Mechanical Engineering Commons^™

Analysis Of Gait Parameters And Knee Angles In Ultimate Frisbee Players: Implications For Balance And Injury, Ethan Nikcevich

Master's Theses

Biomechanics research investigating gait and balance of ultimate frisbee players is an unexplored topic. Ultimate requires a wide range of motions that could improve balance and is also a sport prone to frequent injury. This study explores the impact of playing ultimate on gait parameters associated with balance and knee angles associated with joint injury. Gait trials were conducted on 8 ultimate players and 8 control participants between the ages of 18 and 23 to obtain total double support time, stance phase time, single support time, load response time, abduction-adduction (AA) angles, internal-external (IE) rotation angles, and flexion angles of …

Non-Planar 3d Printing Of Thermosetting Prepolymers, Junaid Abid Ali

Master's Theses

Additive manufacturing or three-dimensional (3D) printing is an advanced process of manufacturing that challenges traditional manufacturing methodologies. However, the current 3D printing process does exhibit specific limitations. It generates printing paths that are in a horizontal plane, proving inadequate for printing curved or non-flat structures. This study established a printing procedure capable of simultaneously executing printing in X, Y, and Z directions. The limitations posed by conventional 3D printing lead to the poor surface quality of curved printed objects. In contrast, non-planar 3D printing provides smoother surfaces. This work developed a program capable of producing non-planar print paths for the …

Co-Simulation Of Active Magnetic Bearing Rotors Using Adams, Msc Apex, And Simulink, Shea A. Charkowsky

Master's Theses

Apex-Adams-Simulink co-simulation is applied to active magnetic bearing (AMB) rotors, demonstrating results unshown in literature, including continuous frequency response, and unavailable in known rotor dynamics software, including touchdown bearing impact. AMBs levitate rotors without contact, so they involve no friction, wear, lubrication, pollution, or shaft speed limits and are thus valuable for large, high-speed applications. Modeling of such rotors, necessary for safety and performance, simultaneously requires flexible body dynamics and advanced control design, but simulation programs tend to specialize in only one or the other. The co-simulation method combines multiple such programs—MSC Apex (finite element modeling), Adams (multibody dynamics), and …

Theoretical And Experimental Study Of Active Magnetic Bearing Control Integrated On Bently's Rotor Kit, Arturo Mario Flores

Master's Theses

This thesis focuses on the comprehensive study of controlling a customized Active Magnetic Bearing (AMB) installed on Bently Nevada’s RK4 rotor kit in Cal Poly’s Vibrations and Rotordynamics Lab. The AMB was uniquely designed and manufactured by a Cal Poly senior project team to fit Bently’s rotor kit and the results of this research are distinctive to the custom system. To achieve practical functionality of the AMB system, we designed a controller a Virtual Instrument (VI) using the National Instrument software, LabVIEW. From the experimental study, we calibrated the programming to find unknown parameters of the AMB system and validated …

Implementation Of Topology Optimization Into The Mechanical Design Process, Nolan Clapp

Master's Theses

Topology Optimization is a lightweighting method based on finite element analysis that produces a part with optimum material distribution in the design space. Results from topology optimization often have organic shapes and curves that are difficult if not impossible to machine with traditional subtractive manufacturing methods. This paper analyzes the implementation of the Solidworks® Topology Optimization add-in into the mechanical design process and discusses required postprocessing to ensure manufacturability of the optimized part though a case study on two example parts. Results of traditional optimization, topology optimization and “selective” optimization (optimization using the results from topology optimization to selectively remove …

Statistical Uncertainty Of The Ignition Time, Burning Rate, And Extinction Characteristics Of Engineered Timber Products, Jacob David

Master's Theses

The characterization of flammability parameters such as time to ignition, mass loss rate (MLR), and extinction criteria is critical for understanding ignition and burning behavior of timber products. These parameters, often determined with bench scale experiments, have previously been presented in literature. However, standard test methods generally use relatively low trial quantities (e.g., n=3) which can potentially cause large variation in reported values. This study investigates the influence of trial quantity on observed statistical variation in key flammability metrics for timber products (e.g., ignition time, peak MLR, MLR at extinction). Using a conical heater, 100 repeat trials were conducted …

Development Of A Low-Cost Acoustic Gauge For Simultaneous Tide And Wave Measurement, Alexander Kalman Dunn

Master's Theses

High-quality tide and wave data are essential in a variety of fields including coastal engineering, climate science, disaster response, and recreational activities. Accurate data are publicly accessible from government organizations such as the National Oceanic and Atmospheric Administration (NOAA), however the high costs associated with deploying and maintaining their high accuracy gauges results in a deficit of localized data. Commercial gauges available starting at $2,000 are still expensive for local agencies and individual users to deploy and maintain. These commercial options can also be limited in their scope, accuracy, or ease of use. In this thesis, a low-cost acoustic gauge …

A Proof Of Concept For Detection Of Palato-Lingual Contact Without Intraoral Electrodes In A Human Participant, Amitava Biswas

Master's Theses

The author of this thesis conceived and investigated an unexpected electrical signal that may not be noticed during regular electroglottography (EGG) when electrodes are conventionally placed on the anterior surface of the throat. It appears that there is a measurable electrical signal from the EGG equipment when electrodes are placed over the frontal cheek (belly of zygomatic muscle), and the tongue is elevated to contact the hard palate, or the tongue is lowered to break the contact. Therefore, this phenomenon is designated as unconventional electroglottography (UEGG, Dr. Steven Cloud, private communication, July 17, 2022).

Two distinctive patterns of waveforms were …

Trace Dna Detection Using Diamond Dye: A Recovery Technique To Yield More Dna, Leah Davis

Master's Theses

This study aspires to find a new screening approach to trace DNA recovery techniques to yield a higher quantity of trace DNA from larger items of evidence. It takes the path of visualizing trace DNA on items of evidence with potential DNA so analysts can swab a more localized area rather than attempting to recover trace DNA through the general swabbing technique currently used for trace DNA recovery. The first and second parts consisted of observing trace DNA interaction with Diamond Dye on porous and non-porous surfaces.

The third part involved applying the Diamond Dye solution by spraying it onto …

Rattus Norvegicus As A Biological Detector Of Clandestine Remains And The Use Of Ultrasonic Vocalizations As A Locating Mechanism, Gabrielle M. Johnston

Master's Theses

In investigations, locating missing persons and clandestine remains are imperative. One way that first responder and police agencies can search for the remains is by using cadaver dogs as biological detectors. Cadaver dogs are typically used due to their olfactory sensitivity and ability to detect low concentrations of volatile organic compounds produced by biological remains. Cadaver dogs are typically chosen for their stamina, agility, and olfactory sensitivity. However, what is not taken into account often is the size of the animal and the expense of maintaining and training the animal. Cadaver dogs are typically large breeds that cannot fit in …

Development Of Mirror Flexures For Use In The Muvi Instrument, Colin W. Harrop

Master's Theses

The Miniaturized Ultraviolet Imager (MUVI), is a compact wide field UV imaging instrument in development at UC Berkeley Space Sciences Laboratory and Cal Poly, San Luis Obispo. MUVI is designed to fit in a 2U CubeSat form factor and provide wide field, high resolution images of the ionosphere at far ultraviolet wavelengths. This thesis details the design and analyses of MUVI’s deployable cover mirror mounting flexures. Three different flexure geometries were evaluated, an optimal candidate was determined based on a number of criteria including isolation of vibration and stress to the mirrors, manufacturability and cost. The design of the flexure …

Trajectory-Tracking Control Of The Ball-And-Plate System, Dominic E. Riccoboni

Master's Theses

The Mechatronics group in the Mechanical Engineering department of Cal Poly is interested in creating a demonstration of a ball-and-plate trajectory tracking controller on hardware. The display piece will serve to inspire engineering students to pursue Mechatronics and control theory as an area of study. The ball-and-plate system is open-loop unstable, underactuated, and has complicated, nonlinear equations of motion. These features present substantial challenges for control - especially if the objective is trajectory tracking. Because the system is underactuated, common nonlinear trajectory tracking control techniques are ineffective. This thesis lays out a theoretical foundation for controlling the hardware.

Several important …

Micro-Scale Laser-Induced Fluorescence Thermometry For Multiphase Flow In Porous Media, Samuel J. Simmons

Master's Theses

In this thesis the use of Laser-Induced Fluorescence (LIF) thermometry was evaluated as a temperature measurement for multiphase flow in porous media. This optical temperature measurement technique utilizes the temperature-dependent emissive properties of fluorescent dyes to measure temperature. This research evaluates the accuracy, spatial resolution, and temporal resolution of LIF thermometry compared to existing temperature measurements. In this research water-soluble and oil-soluble fluorescent dyes are evaluated in terms of their temperature sensitivity. The ability of these dyes to measure temperature is compared to an Ansys FEA simulation of a fixed temperature gradient. For multiphase flow, the fluorescent dyes were both …

Design Of A System To Investigate The Relationship Between Feedback And Delivery Medium For A Novel Motor Task, Ashley Humpal

Master's Theses

Stroke is a chronic, lifelong illness, and full recovery requires continuous physical and cognitive rehabilitation. Such long-term rehabilitation is cost-prohibitive; however an approach to providing long-term therapy that has recently gained traction is the use of socially assistive agent (SAA) systems. These systems make use of non-contact communication devices and can be used to guide people through a variety of rehabilitative tasks. They have the potential supplement current rehabilitation practices by providing motivation during intense exercises, and can extend the reach of the therapist into remote and home settings.

Though SAA systems have been used in a variety of rehabilitative …

The Rise Of Terrorism In Africa And What It Means For U.S. Policymakers, Bridget Mary Hughes

Master's Theses

This thesis utilizes three case studies to measure the rise of terrorism in Africa. This qualitative data leads the reader to one ultimate question: what does the rise in terrorism in Africa mean for the United States (U.S.) and U.S. policymakers, National Security academia, students in National Security, if anything at all? The answer is: if civilian and military compounds are being targeted by these violent extremists, as these three case studies demonstrate, it is my recommendation that U.S. policymakers cease sending troops to the African theater and, instead, allocate funding to the citizens and nonprofits of the countries whom …

Hypoxic Incubation Chamber, Simone Lisette Helfrich, Makenzie Nicole Jones

Master's Theses

This paper describes the design, manufacturing, and testing of a novel controllable hypoxic incubator with fully functional oxygen gas control and temperature control in a humid environment. On the current market, a majority of the few hypoxic incubators use pre-mixed gas that does not offer precise control over gas concentration. The objective for this project was to create a chamber that allows the user to set the O2 concentration to varying set points of % O2 while maintaining the chamber at a constant body temperature, CO2 level, humidity, and sterility. To start the project, multiple concepts were developed for the …

Pressure Disturbance Upstream Of The Boundary Layer Data System, Michelle S. Leclere

Master's Theses

The primary objective for this work was to evaluate the reliability of computational fluid dynamics (CFD) tools in the prediction of upstream surface pressure disturbance and pressure drag of various instrument excrescence shapes for a small aircraft flight test device called the Boundary Layer Data System (BLDS). Insights on pressure disturbance will serve as a guide for the placement of BLDS probes/sensors, and pressure drag can be used to ensure sufficient adhesive is used to install BLDS instrumentation. The Mach number for all CFD cases was 0.12 and the Reynolds number based on excrescence height varied from 4 x 10 …

System Identification Of A Cantilever Beam With Interferometer Measurement Using Adaptive Filters, Jordan D. Kochavi

Master's Theses

Laser interferometry, commonly used in high-precision motion control systems, is rarely adopted in experimental vibration analysis because its installation and mounting is invasive to dynamical systems. However, metrology systems that already utilize laser interferometry, such as profilometry in semiconductor manufacturing, may benefit from interferometer feedback for signal processing. This study investigates the use of laser interferometry for system identification through a piezoelectrically actuated cantilevered beam.

The model of the beam including piezo actuators and optical measurement components are established through the Euler-Bernoulli beam theory. From the method of separation of variables, the continuous system is transformed into a discrete system …

Modeling And Control Of A Planar Bounding Quadrupedal Robot, Patrick John Ward

Master's Theses

Legged robots have the potential to be a valuable technology that provides agile and adaptive locomotion over complex terrain. To realize legged locomotion's full abilities a control design must consider the nonlinear piecewise dynamics of the systems. This paper aims to develop a controller for the planar bounding of a quadrupedal robot.

The bounding of the quadruped robot is characterized by a simplified hybrid model that consists of two subsystems for stance and flight phases and the switching laws between the two states. An additional model, the Multibody model, with fewer simplifications, is used concurrently to best approximate real-world behavior. …

Design Of A Proprioceptive Actuator Utilizing A Cycloidal Gearbox, Craig John Kimball

Master's Theses

Legged robotics creates the demand for high torque compact actuators able to develop high instantaneous torque. Proprioceptive actuator design theory is a design theory that removes the need for a torque feedback device and relies on the stiffness in the leg for absorbing the high Ground Impact Forces created by walking locomotion. It utilizes a high torque density motor paired with a gearbox with a high gear ratio for torque multiplication. Previously work has been done to design a proprioceptive actuator design that utilizes a planetary gearbox to create a modular low-cost actuator for legged robotics. The purpose of this …

Numerical Modelling Of Elastic Wave Propagation In Anisotropic Media Using The Finite-Difference Time Domain (Fdtd) And Elastodynamic Finite Integration Technique (Efit), Seth M. Golembeski

Master's Theses

As ultrasonic testing becomes increasingly widespread, education and simulation in UT becomes increasingly useful. This thesis describes development of two simulations - the first, a Finite Difference Time Domain method that can be deployed to consumer GPUs. This simulation is designed to be user-friendly and provide quick interactivity for pedagogical use, for example, in a classroom or industry training. The second simulation is an anisotropic Elastodynamic Finite Integration Technique implementation, which can be deployed to high performance computers for large-scale parallel simulations. This anisotropic simulation is, to the author’s knowledge, the first open-source implementation of anisotropic EFIT.

Model-Based Design Of An Optimal Lqg Regulator For A Piezoelectric Actuated Smart Structure Using A High-Precision Laser Interferometry Measurement System, Grant P. Gallagher

Master's Theses

Smart structure control systems commonly use piezoceramic sensors or accelerometers as vibration measurement devices. These measurement devices often produce noisy and/or low-precision signals, which makes it difficult to measure small-amplitude vibrations. Laser interferometry devices pose as an alternative high-precision position measurement method, capable of nanometer-scale resolution. The aim of this research is to utilize a model-based design approach to develop and implement a real-time Linear Quadratic Gaussian (LQG) regulator for a piezoelectric actuated smart structure using a high-precision laser interferometry measurement system to suppress the excitation of vibratory modes.

The analytical model of the smart structure is derived using the …

Development Of A Body Weight Reduction Algorithm In Micro-Gravity Treadmills™, Alexander Hibbert

Master's Theses

Boost Treadmills™, a company specializing in the use of differential air-pressure (DAP) technology in the realm of exercise and rehabilitation, is developing their second-generation micro-gravity treadmill™ named the Boost 2. This machine will allow individuals in all types of fitness environments to move and exercise at a fraction of their normal body weight, reducing the impact forces on lower body extremities and allowing for accelerated returns to activity.

The purpose of this thesis was to create an algorithm to be implemented on the Boost 2 that related the percentage of body weight reduction of a user to a required pressure …

Development Of A Prototype Ball-And-Plate Balancing Platform, Scott J. Mangin

Master's Theses

Ball-and-plate balancing platforms have been utilized throughout academia to further understanding of nonlinearities that can occur when applying control algorithms to nonholonomic and underactuated systems. The objective of this thesis is to build upon an existing ball-and-plate balancing platform used in the Intro to Mechatronics class and create a robust platform system that can be utilized by future students to test various controller designs derived from MATLAB/Simulink®. The ball-and-plate platform design uses a myriad of sensors to track the system components in real time: a resistive touch panel is used to track the position of the ball on the plate, …

Effect Of Indentation On Sandwich Composite Structure Mechanical Behavior, Marius V. Jatulis

Master's Theses

Composite sandwich structures are prevalent in engineering applications where high strength to weight ratios are critical. A composite sandwich includes the addition of a core material between two composite face sheets to increase ultimate stress in compression and bending loading cases. The performance of many composite sandwich structure configurations is well understood in the undamaged case. This analysis examines a type of damage, low velocity indentation, and determines the effect on mechanical behavior. The scope of the analysis includes manufacturing sandwich composite structures, creating indentation in the composite, and testing the sandwich composite structure. The mechanical behavior of the composite …

System Performance Model And Control System For A Small-Scale Horizontal Axis Wind Turbine, Niko Banks

Master's Theses

Predicting the performance of wind turbines is a key part of the turbine design process and operation, as predictive models play a large role in determining potential power output and efficiency at different operating conditions to help maximize production. On small-scale wind turbines performance models become more complex, as the rotor aerodynamic performance depends not only on the tip speed ratio, but also on the flow Reynolds number. An accurate predictive model that includes this behavior on small-scale wind turbines can be used to find the optimal operating conditions for power output, and is also a critical component of the …

An Analysis Of Thermal Comfort Perception In Cal Poly's Math & Science Building, Pouria Ali Fariborzi

Master's Theses

Since Americans, on average, spend approximately 90% of their time indoors according to the EPA, it is crucial to provide room occupants with the best, most comfortable, and healthiest possible environment, which is known as Indoor Environmental Quality (IEQ). This thesis aims to identify how we can provide comfortable learning environments to improve student success. To determine the best possible environment for occupants, a model of the Math & Science Building was developed, validated, and modified using DesignBuilder. In addition, we compared thermal comfort surveys to actual measured conditions for some classrooms. Analysis indicates that students prefer a cooler thermal …

Medial And Lateral Tibiofemoral Contact Forces For Individuals With High Body Mass Index In Gait And Cycling Training, Reymil Fernandez

Master's Theses

The prevalence of knee osteoarthritis, a degenerative joint disease characterized by the degradation of articular cartilage, is correlated with the rise in obesity. The rising rates of obesity in children and adults highlight the need for identifying a sustainable physical activity that promotes fitness while mitigating initiation and progression of osteoarthritis. The objective of this study was to determine an effective rehabilitation and lifelong fitness sustainment exercise regimen that minimize risk of osteoarthritis in individuals with high body mass index (BMI). The aim was to examine knee medial and lateral contact forces in gait and cycling training. Gait at self-selected …

Triangular Cosserat Point Element Method For Reducing Soft Tissue Artifact: Validation And Application To Gait, Jake Edward Deschamps, Stephen Klisch

Master's Theses

Human motion capture technology is a powerful tool for advancing the understanding of human motion biomechanics (Andriacchi and Alexander, 2000). This is most readily accomplished by applying retroreflective markers to a participant’s skin and tracking the position of the markers during motion. Skin and adipose tissue move independently of the underlying bone during motion creating error known as soft tissue artifact (STA), the primary source of error in human motion capture (Leardini et al., 2005).

(Solav et al., 2014) proposed and (Solav et al., 2015) expanded the triangular Cosserat point element (TCPE) method to reduce the effect of STA on …

Printed Circuit Board Design And Layout For Hobbyists, Engineers, And Students, Michael A. Derrenbacher

Master's Theses

Printed Circuit Boards (PCBs) are a ubiquitous element of virtually every electronic system manufactured world-wide. It is not a stretch of the imagination to say that if it’s electronic, there is a PCB in it. PCBs are necessary tools for electronics work, and tools need to have instructions. For better or worse, PCB knowledge is a deep and wide ocean. There is much to cover for even a surface level understanding, and there are deep areas rich in technical expertise. Navigating the ocean of knowledge is treacherous; common knowledge of yore can be downright dubious now. PCB manufacturing and electronics …