Mechanical Engineering Commons^™

Fundamental Characteristics Of Supercritical Co2 Combustion, Raghu Veera Manikantachari Kancherla

Electronic Theses and Dissertations

The direct-fired supercritical CO2 (sCO2) cycle is conceptually superior to many of the trending energy production technologies due to their remarkably promising efficiency, environmental friendliness and cost. The accurate simulation of this combustion is very important because the operating conditions are very challenging to its experimentation. Hence, the current work focuses on identifying various thermal, transport, chemical kinetic models, investigating various fundamental characteristics and verifying the validity of important underlying modeling assumptions in focus to supercritical CO2 combustion. In the current work, various thermal and transport property models are identified based on accuracy, computational cost and ease of implementation for …

Analytical Modeling And Life Cycle Assessment Of A Solar Powered Vapor Absorption Cooling System, Harold A. Walters

Electronic Theses and Dissertations

Vapor absorption cooling systems (VACS) offer an environmentally friendly alternative to the standard vapor compression cooling systems (VCCS) for cooling homes, businesses, factories, and other buildings. VACS use low-grade thermal energy to achieve a cooling effect and require minimal electrical input for the liquid solution pump used for circulation within the system. The thermal energy which powers these systems can be provided through several means; one popular form is through the use of solar thermal collectors. This paper provides a process for determining the overall size and configuration of the VACS depending upon the operating conditions of selected components. A …

Numerical Investigation And Optimization Of Pin Fins In Micro Heat Sinks, Fuad Ismayilov

Electronic Theses and Dissertations

Operating temperature in electronics applications is continuously increasing. Therefore, for the past few decades, high heat flux removing micro heat sinks are investigated in terms of heat transfer effectiveness. This study generally concentrates on improving the passive heat transfer techniques. Micro heat sinks used in experiments are fabricated using MEMS techniques. Resistance temperature detectors, RTDs, were used for temperature measurements. The experimental data was obtained for single and two phase flow regions; however, only single phase flow results were considered in numerical simulations. Numerical validations were performed on the micro heat sinks, including cylinder and hydrofoil shaped pin fins. Following …

Fluid Flow Characteristics Of A Co-Flow Fluidic Slot Jet Thrust Augmentation Propulsion System, Brian Garrett

Electronic Theses and Dissertations

The UAV industry is booming with investments in research and development on improving UAV systems in order to increase applications and reduce costs of the use of these machines. Current UAV machines are developed according to the quadcopter design which has a rotary propulsion system which provides the lift needed for the aerial vehicles. This design has some flaws; namely safety concerns and noise/vibration production both of which come from the rotary propulsion system. As such, a novel propulsion system using slip stream air passed through high performance slot jets is proposed and analysis of the fluid characteristics is presented …

A Study Of Organo-Phosphorous Simulants Thermal Destruction Using Shock Tube/Laser Diagnostics Techniques And Chemical Kinetics Modeling, Sneha Neupane

Electronic Theses and Dissertations

High-fidelity chemical kinetic models are critical in predictive modeling during design and optimization of next generation energy systems. Shock tube provides an ideal tool to investigate high-temperature chemical kinetics. Non-intrusive laser absorption diagnostics provide in-situ measurements of quantitative, time-resolved species concentration data in this complex chemically reacting system. In this work, shock tube and laser absorption spectroscopy were utilized to measure species concentration time-histories during pyrolysis and oxidation of organo-phosphorous compounds (OPCs). The experiments data obtained were used as benchmark to develop an improved kinetic model of OPCs combustion. Interest in combustion chemistry of OPCs is associated to their use …

Molecular Dynamics Study Of Sintering Behavior Of Single-Crystal, Bimetallic Core/Shell Alloy, And Intermetallic Alloy Nanoparticles, Jungmin Jeon

Electronic Theses and Dissertations

There has been rapidly growing interest in the sintering process of nanoparticles (NPs) among academia and modern industry due to their promising applications in additive manufacturing (AM) based on the overall improved properties at nanoscale. In the past decade a lot of experimental and computational work has been conducted to study the sintering process of powder materials. However there is still a significant knowledge gap in a fundamental understanding of the thermodynamics and nanostructural evolution of NPs undergoing additive manufacturing. This thesis aims to gain fundamental insights into melting behavior of different materials including single-crystal bimetallic core/shell alloy and intermetallic …

Experimental And Numerical Investigation Of A Novel Adsorption Bed Design For Cooling Applications, Ramy H. Mohammed

Electronic Theses and Dissertations

A global challenge is to develop environmentally friendly, affordable, compact and sustainable technologies to provide heating and cooling power. Adsorption cooling (AC) technology is one of the most promising ways to solve the environmental issues and cut down the energy consumption related to the traditional air conditioning and refrigeration systems. However, AC systems still suffer from poor heat and mass transfer inside the adsorption bed, which is the main obstacle to commercialization of adsorption cooling units. The main goal of this study is designing an efficient adsorption cooling cycle. In this research work, an in-depth scaling analysis of heat and …

Applied Deep Learning In Orthopaedics, William Stewart Burton Ii

Electronic Theses and Dissertations

The reemergence of deep learning in recent years has led to its successful application in a wide variety of fields. As a subfield of machine learning, deep learning offers an array of powerful algorithms for data-driven applications. Orthopaedics stands to benefit from the potential of deep learning for advancements in the field. This thesis investigated applications of deep learning for the field of orthopaedics through the development of three distinct projects.

First, algorithms were developed for the automatic segmentation of the structures in the knee from MRI. The resulting algorithms can be used to accurately segment full MRI scans in …

Knee Balance Assessment During Cementation Is Detrimental To Initial Tka Tibial Tray Fixation, Yashar Ali Behnam

Electronic Theses and Dissertations

Despite recent advancements in implant design and cement technique, aseptic tibial loosening remains the primary cause of revision after cemented total knee arthroplasty (TKA) [1]. While the mechanisms of tibial loosening are multifactorial, previous research has shown that third-generation cement techniques, including the use of jet lavage and cement pressurization, can reduce contamination of the implant surface by lipids endogenous to the surrounding cancellous bone and thereby enhance fixation strength between the implant and bone [2]. The purpose of this thesis is to understand the role contaminating lipids play in the mechanism of aseptic loosening and to perform a cadaveric …

Controlled Bubble Dynamics Inside Micropillar Arrays, Faraz Khalil Arya

Electronic Theses and Dissertations

Bubble dynamics inside micro domains was manipulated and used to pump liquid. Micropillars were formed inside two 1.5 mm wide and 220 µm high microchannels with a length of 23 mm. One microchannel had three arrays of micropillars with diameters of 40 µm and the other had a single array of micropillars with diameters of 30 µm. An array of five 200 µm by 200 µm heaters was deposited inside these micropillar arrays and was used to control bubble size and trajectory. A sequential power switching of the heaters was used to pump liquid in a desired direction with a …

Development Of A Neural Network-Based Object Detection For Multirotor Target Tracking, Spencer Harwood

Electronic Theses and Dissertations

Unmanned aerial vehicles (UAVs) have, for the past few decades, seen an increased popularity in industry and research centres. Despite this intense utilization by both markets there exists an active demand for the development of autonomous guidance, navigation, and control strategies. One need relates to the achievement of a high level of autonomy to identify and track a target object. An elective technique for this set of tasks is neural networks. In the development and study of these networks there is a distinct lack of substantive validation techniques to qualify network performances when implemented in a multirotor UAV. This thesis …

Static Load Bolted Joint Elastic Resilience Testing Methodology, Paul Melino

Electronic Theses and Dissertations

Elastic resilience is the ratio of deformation over force an object experiences when under stress. Knowing the how much the bolt and clamped part deform under load is critical when determining fasteners for a bolted joint. VDI 2230 is the internationally recognized bolt sizing standard and contains the equations used to determine each of the bolted joint component’s resilience as well as values for embedment estimates based on component surface roughness. Embedment is the local plastic deformation due to uneven contact over the contact planes of a bolt-clamped interface (Bolt head to plate, plate to plate, plate to nut, and …

Side-To-Side Comparison Of Total Shoulder Arthroplasty And Intact Function In Individuals, Sarah Rose Walden

Electronic Theses and Dissertations

Total Shoulder Arthroplasty (TSA) is a surgery which replaces the shoulder joint, or the interface between the humerus and the scapula glenoid. To test TSA success, most prior research compares patients with TSA to healthy controls. However, the shoulder anthropometry, motion, and musculature of individuals varies widely across the population making it important to assess TSA performance in individuals. The overall goal of this study is to determine if patients with one of two TSA implant designs on one side achieve the same range of motion as their intact side, and if so to find if they compensate using increased …

Process-Property-Microstructure Relationships In Laser-Powder Bed Fusion Of 420 Stainless Steel., Subrata Deb Nath

Electronic Theses and Dissertations

Laser-powder bed fusion (L-PBF) is an additive manufacturing technique for fabricating metal components with complex design and customized features. However, only a limited number of materials have been widely studied using L-PBF. AISI 420 stainless steel, an alloy with a useful combination of high strength, hardness, and corrosion resistance, is an example of one such material where few L-PBF investigations have emerged to date. In this dissertation, L-PBF experiments were conducted using 420 stainless steel powders to understand the effects of chemical composition, particle size distribution and processing parameters on ensuing physical, mechanical and corrosion properties and microstructure in comparison …

Low Temperature Desiccants In Atmospheric Water Generation., Sunil Gupta

Electronic Theses and Dissertations

Surging global water demand as well as changes to weather patterns and over exploitation of natural water sources, such as ground water, has made potable water a critical resource in many parts of the World already – one rapidly heading towards a crisis situation. Desalination has been adopted as a solution – this is however energy intensive and impractical for most of the developing countries - those most in need of water. A renewable source of energy is solar thermal and solar photovoltaic. A plentiful source of water is the humidity in the atmosphere. This research is to push the …

Thermodynamic Modeling And Transient Simulation Of A Low-Pressure Heat Recovery Steam Generator Using Siemens T3000, Andres Caesar

Electronic Theses and Dissertations

With world energy consumption rising, and nonrenewable energy resources quickly depleting, it is essential to design more efficient power plants and thereby economically utilize fossil fuels. To that end, this work focuses on the thermodynamic modeling of steam power systems to enhance our understanding of their dynamic and transient behavior. This thesis discusses the physical phenomena behind a heat recovery steam generator (HRSG) and develops a mathematical description of its system dynamics. The model is developed from fundamentals of fluid dynamics, phase change, heat transfer, conservation laws and unsteady flow energy equations. The resulting model captures coupled physical phenomena with …

Large Scale Cryogenic Storage With Active Refrigeration, Adam Swanger

Electronic Theses and Dissertations

Storage and transfer of cryogenic liquefied gases on volume scales from under 10 liters for lab use, up to hundreds of millions of liters for industrial applications is of paramount importance across a vast range of industries. Traditionally, these commodities have been stored at or near the normal boiling point due to relative ease of operation and safety-related considerations; however, this also means that some percentage will always be lost due to environmental heat leaking into the vessel and causing boiloff. These losses become more concerning as scales increase, and are of particular importance for high-cost commodities such helium and …

Temperature Effects On Helium Filled Soap Bubble Particle Tracking Velocimetry., Michael C. Blum

Electronic Theses and Dissertations

Helium Filled Soap Bubble (HFSB) Particle Tracking Velocimetry (PTV) methods are becoming increasingly popular as they provide a low cost, safe option for reliable flow visualization. Several studies have been conducted to understand the accuracy of such systems under normal temperatures and pressures; however, no such studies to date have examined accuracy of HFSB PTV at high temperatures. The goal of this study is to characterize the capability of HFSB PTV methods to visualize air flow through a rectangular duct at elevated temperature. A heated wind tunnel was designed to heat up to 150 m³/h of 25 °C …

Material-Process-Property Relationships Of 17-4 Stainless Steel Fabricated By Laser-Powder Bed Fusion Followed By Hot Isostatic Pressing., Harish Irrinki

Electronic Theses and Dissertations

17-4 PH stainless steel is commonly used in medical, tooling, automotive, chemical and aerospace industries due to its excellent strength and corrosion properties. Additive manufacturing processes such as laser-powder bed fusion (L-PBF) have gained attention and importance due to the potential to produce complex-shaped three-dimensional parts for various industries. In order to manufacture three-dimensional components from 17-4 PH stainless steel powder using L-PBF, it is critical for design and manufacturing engineers to have an awareness of various material options and corresponding processing and post-processing conditions to obtain useful mechanical properties from the process. The goal of this dissertation is to …

Microstructure And Mechanical Properties Of Selective Laser Melted Superalloy Inconel 625., Md Ashabul Anam

Electronic Theses and Dissertations

Selective Laser Melting (SLM), a powder based Additive Manufacturing (AM) process, has gained considerable attention in the aerospace, biomedical and automotive industries due to its many potential benefits, such as, capability of fabricating complex three-dimensional components, shortened design to product time, reduction in process steps, component mass reduction and material flexibility. This process uses metallic powder and is capable of fabricating complex structures with excellent microstructure which make SLM not only an improvement over other manufacturing processes but also innovative material processing technology. Inconel 625, a nickel-based super alloy is widely popular in aerospace, chemical and nuclear industries. This alloy …

High Dynamic Range Optical Devices And Applications., Elijah Robert Jensen

Electronic Theses and Dissertations

Much of what we know about fundamental physical law and the universe derives from observations and measurements using optical methods. The passive use of the electromagnetic spectrum can be the best way of studying physical phenomenon in general with minimal disturbance of the system in the process. While for many applications ambient visible light is sufficient, light outside of the visible range may convey more information. The signals of interest are also often a small fraction of the background, and their changes occur on time scales so quickly that they are visually imperceptible. This thesis reports techniques and technologies developed …

Translating Data From The Laboratory Into Simulation: A Computational Framework For Subject-Specific Finite Element Musculoskeletal Simulation, Donald R. Hume

Electronic Theses and Dissertations

Computational modeling is a powerful tool which has been used to inform decisions made by engineers, scientists, and clinicians for decades. Musculoskeletal modeling has emerged as a computational modeling technique used to understand the interaction between the body and its surroundings. There are several common approaches used for musculoskeletal modeling which take advantage of different model formulations to obtain information of interest. Unfortunately, models with different joint formulations inherit disparities in representations of ligament, muscle, and cartilage at joints of interest. These differences affect the way the joint functions and limit the insight it provides through computational analysis. Musculoskeletal models …

Modeling And Validations Of Control Parameters For Material Extrusion-Based Additive Manufacturing Of Thixotropic Aluminum Alloys., Lars Herhold

Electronic Theses and Dissertations

Additive Manufacturing (AM) with metals has been accomplished mainly through powder bed fusion processes. Initial experiments and simulations using Material Extrusion Additive Manufacturing (MEAM) have been performed by various researchers especially using low melting alloys. Recently Stratasys Inc. submitted a patent application for the use of their Material Extrusion technology also called Fused Deposition Modeling (FDM) where they describe the process using thixotropic semi-solid alloys. Currently this process using semi-solid, engineering type alloys such as A356 or THIXALLOY 540 aluminum have not been researched to evaluate the control parameters. This research combines the in-depth knowledge of applying thixotropic semi-solid aluminum …

Selecting The Most Effective Energy Modeling Tool Based On A Project Requirement, Sodiq Akande

Electronic Theses and Dissertations

Building energy usage can be derived and controlled by performing building energy modeling. BEM can be performed using numerous software tools such as DesignBuilder, OpenStudio, EnergyPlus etc. These modeling tools can be sorted into three different modeling categories: Black-box, Gray-box and White-box. It is important for a modeler to be able to quickly select the proper tool from the proper category to meet the need of the project. To validate the method of categorizing tools, the three models generated using tools from each category and the modeling outputs required were compared. Each model was designed to estimate the amount of …

Tooling For Injection Molding Using Laser-Powder Bed Fusion., Mohith Ram Buxani

Electronic Theses and Dissertations

Laser-Powder Bed Fusion (L-PBF) has been considered for some time by the injection molding industry for the fabrication of tooling for injection molding in order to address large lead times and costs for tool-making. Computer-aided simulations are also routinely used to evaluate new part and mold designs as well as understanding the effects of material compositions and processing conditions on part quality and overall productivity. However, there remains a significant need to integrate the perspectives from injection molding, 3D printing, metal powders, and component design and process simulation to better utilize LPBF for fabricating tooling required for injection molding. The …

Ultrasonic Nondestructive Evaluation Of Metal Additive Manufacturing., Venkata Karthik Nadimpalli

Electronic Theses and Dissertations

Metal Additive Manufacturing (AM) is increasingly being used to make functional components. One of the barriers for AM components to become mainstream is the difficulty to certify them. AM components can have widely different properties based on process parameters. Improving an AM processes requires an understanding of process-structure-property correlations, which can be gathered in-situ and post-process through nondestructive and destructive methods. In this study, two metal AM processes were studied, the first is Ultrasonic Additive Manufacturing (UAM) and the second is Laser Powder Bed Fusion (L-PBF). The typical problems with UAM components are inter-layer and inter-track defects. To improve the …

Materials Design With Polylactic Acid-Polyethylene Glycol Blends Using 3d Printing And For Medical Applications., Jeremiah R. Bauer

Electronic Theses and Dissertations

This thesis is an examination of two material systems derived from polylactic acid (PLA) and polyethylene glycol (PEG). PLA is a polymer commonly sourced from renewable sources such as starches and sugars. It is a relatively strong, biodegradable polymer, making it ideal for use in the body. Even though it has a relative high strength, PLA is also brittle leading to the use of plasticizers to increase flexibility. One such plasticizer is PEG, which is a material that can exist at room temperature as either a thin liquid, or a hard waxy solid depending on the molecular weight. The first …

Optimal Operation Of Integrated Microgrids, Abdullah Albaker

Electronic Theses and Dissertations

Microgrids' deployments are increasing and projected to increase even more in future due to the significant advantages that are provided by this technology for end-use customers. However, microgrids can be connected to each other to create integrated microgrids system, which can further promote the anticipated and desired benefits. An integrated operation of microgrids can potentially improve the local power system reliability and resilience, increase the individual microgrids' economic benefits, and promote further utilization of renewable energy resources. Integrating microgrids, to achieve a microgrid network or cluster, is expected be an essential application towards smarter power grids and a key operational …

Pressure Image Based Attitude Controller For Small Unmanned Aerial Vehicles, Kenneth Thompson

Electronic Theses and Dissertations

As technology improves, small unmanned aerial vehicles (SUAV) have been identified for their utility in a variety of applications in which larger unmanned craft may be incapable of accomplishing mission objectives. These aircraft with their small size and long flight durations are ideal for hazardous inspection and long duration surveillance missions. One challenge preventing the widespread adoption of these systems is their instability to abrupt changes in the flow field around them due to wind gusts or flow separation. Currently, traditional rigid body based sensors are implemented in their flight control systems, which are sufficient in higher inertia aircraft for …

A Modeling Framework Of Brittle And Ductile Fractures Coexistence In Composites, Yangyang Qiao

Electronic Theses and Dissertations

In order to reduce the weight of automobiles and aircrafts, lightweight materials, such as aluminum alloy, advanced high strength steel, composite materials, are widely used to replace the traditional materials like mild steel. Composite materials are complicated in material mechanical properties and less investigated compared to metallic materials. Engineering composites can be categorized into polymer matrix composites (PMCs), metal matrix composites (MMCs) and ceramic matrix composites (CMCs) according to their matrix materials. A set of mechanical experiments ranging from micro scale (single fiber composite and thin film composite) to macro scale (PMCs and MMCs) were conducted to fully understand the …