Mechanical Engineering Commons^™

Combustion And Emission Characteristics Of Ic Engines Fueled By Hydrogen And Hydrogen/Diesel Mixtures And Multi-Objective Optimization Of Operating Parameters, Abdulhakim Issa Jabbr

Doctoral Dissertations

“The present study considers combustion of hydrogen in IC engines. In general, the work focuses on simulating the engine performance and emissions at different operation parameters, and using optimization techniques. Task I work deals with the engine performance and emissions of a single cylinder spark-ignition (SI) engine fueled by hydrogen. The engine was simulated at different equivalence ratios, exhaust gas recirculation (EGR) and ignition timing. The results indicate that NOx emissions, engine power, and efficiency are reduced by increasing EGR level, and increased with increasing equivalence ratio and advanced ignition timing. The best operating conditions for hydrogen engines were obtained …

Development Of Horizontal Axis Hydrokinetic Turbine Using Experimental And Numerical Approaches, Abdulaziz Abutunis

Doctoral Dissertations

“Hydrokinetic energy conversion systems (HECSs) are emerging as viable solutions for harnessing the kinetic energy in river streams and tidal currents due to their low operating head and flexible mobility. This study is focused on the experimental and numerical aspects of developing an axial HECS for applications with low head ranges and limited operational space. In Part I, blade element momentum (BEM) and neural network (NN) models were developed and coupled to overcome the BEM’s inherent convergence issues which hinder the blade design process. The NNs were also used as a multivariate interpolation tool to estimate the blade hydrodynamic characteristics …

Hydrokinetic Turbine Composite Blades And Sandwich Structures: Damage Evaluation And Numerical Simulation, Mokhtar Fal

Doctoral Dissertations

“Composite materials are gaining interest due to their high strength to weight ratio. This study deals with both experimental and numerical approaches to cover the aspects of the failure of composite materials in hydrokinetic turbine applications. In Part I, the location and magnitude of failure in the horizontal axis water turbine carbon fiber-reinforced polymer (CFRP) composite blades with different laminate stacking sequences were investigated. Two lay-up orientations were adopted for this work ([0⁰]₄ and [0⁰/90⁰]_2s). A finite element analysis model was generated to examine the stresses along the blade. Five angles were introduced to study the effect …

Additive Manufacturing Of Customized Lithium-Ion Batteries: Process Fundamentals And Applications, Xiaowei Yu

Doctoral Dissertations

“In the pasting decades, considerable efforts have been spent in developing the next-generation lithium-ion batteries (LIBs), from advanced active materials to new manufacturing methods. The development of additive manufacturing (AM) has brought new opportunities to LIBs. In this work, two AM methods are introduced for fabricating electrodes of LIBs. The first method is aerosol printing, which is a solvent-based wet additive method. Whereas the second method is a solvent-free, dry printing method. The commonly used materials for current collectors and active materials (including cathodes and anodes) of LIBs are aerosol printed and the electrochemical functionalities of the printed materials are …

Fabrication And Characterization Of Multifunctional Composites, Aditya R. Thakur

Doctoral Dissertations

“This study details the research to facilitate fabrication and characterization of novel structural composites reinforced with carbon fibers. Across industries, materials with high performance-to-weight ratio are sought after. Using carbon fibers as secondary phases in these proposed composites, specific characteristics can be tailored in these materials to manufacture strong, lightweight, high performance structures. The first part of the research focused on the improvement in the mechanical properties of the composites using carbon fiber reinforcement. As a part of this study, toughened ceramic composites with predictable failure patterns were produced using carbon fiber inclusions. A closed-form analytical model was developed to …

Finite Time Suboptimal Control Design Of Nonlinear Systems With Θ-D Technique And Implementation To Aerospace Applications, Jie Yao

Doctoral Dissertations

“A finite time suboptimal control strategy (named θ - D approximated algorithm) was proposed in this study, which can provide the control engineers with a novel effective and efficient design tool from the finite time optimal perspective. Based on the framework of this proposed method, the original nonlinear dynamics were formulated in pseudo-linear form, and the performance index was denoted by a linear quadratic regulator prototype in this research. After that, the approximated solutions to intractable Hamilton-Jacobi-Bellman (HJB) equation were acquired by putting vanishing perturbation terms into the performance index. By tuning the parameters in perturbation terms, semi-global stability and …

Observer-Based Event-Triggered And Set-Theoretic Neuro-Adaptive Controls For Constrained Uncertain Systems, Abdul Ghafoor

Doctoral Dissertations

"In this study, several new observer-based event-triggered and set-theoretic control schemes are presented to advance the state of the art in neuro-adaptive controls. In the first part, six new event-triggered neuro-adaptive control (ETNAC) schemes are presented for uncertain linear systems. These comprehensive designs offer flexibility to choose a design depending upon system performance requirements. Stability proofs for each scheme are presented and their performance is analyzed using benchmark examples. In the second part, the scope of the ETNAC is extended to uncertain nonlinear systems. It is applied to a case of precision formation flight of the microsatellites at the Sun-Earth/Moon …

Characterization And Recyclability Of 304l Stainless Steel Powder For Use In The Selective Laser Melting Process, Austin Taylor Sutton

Doctoral Dissertations

"Powder-bed fusion refers to a subset of additive manufacturing (AM) methods which successively melts and solidifies selected regions within a powder bed on a layer-by-layer basis to construct components directly from computer-aided design files. Laser Powder-Bed Fusion (L-PBF) is a process among the powder-bed fusion techniques that utilizes a laser to consolidate particles into a material with little porosity. During the L-PBF process, the large energy input from the laser causes the production of ejecta in the form of laser spatter and condensate, both of which have the potential to settle in the surrounding powder bed compromising its reusability. In …

Trajectory Control Of A Wheeled Robot Using Interaction Forces For Intuitive Overground Human-Robot Interaction, George Leno Holmes Jr.

Doctoral Dissertations

"Effective and intuitive physical human robot interaction (pHRI) requires an understanding of how humans communicate movement intentions with one another. It has been suggested that humans can guide another human by hand through complex tasks using force information only. However, no clear and applicable paradigm has been set forth to understand these relationships. While the human partner can readily understand and adhere to this expectation, it would be difficult for anyone to explain their intuitive motions with strict rules, algorithms, or steps. Uncovering such a procedural framework for the control of robotic systems to execute expected performance simply from force …

Development Of A Counter-Flow Thermal Gradient Microfluidic Device, Shayan Davani

Doctoral Dissertations

This work presents a novel counter-flow design for thermal stabilization of microfluidic thermal reactors. In these reactors, precise control of temperature of the liquid sample is achieved by moving the liquid sample through the thermal zones established ideally through the conduction in the solid material of the device. The goal here is to establish a linear thermal distribution when there is no flow and to minimize the temperature change at flow condition. External convection as well as internal flowinduced effects influence the prescribed thermal distribution. The counter-flow thermal gradient device developed in this study is capable of both stabilizing the …

Active-Passive Dynamic Consensus Filters: Theory And Applications, John Daniel Peterson

Doctoral Dissertations

”This dissertation presents a new method for distributively sensing dynamic environments utilizing integral action based system theoretic distributed information fusion methods. Specifically, the main contribution is a new class of dynamic consensus filters, termed active-passive dynamic consensus filters, in which agents are considered to be active, if they are able to sense an exogenous quantity of interest and are considered to be passive, otherwise, where the objective is to drive the states of all agents to the convex hull spanned by the exogenous inputs sensed by active agents. Additionally, we generalize these results to allow agents to locally …

Build Strategy Investigation Of Ti-6al-4v Produced Via A Hybrid Additive Manufacturing Process, Lei Yan

Doctoral Dissertations

“Till now, laser metal deposition (LMD) has been developed with the capability of near-net shape high-performance metal parts fabrication, especially complicated titanium alloys, nickel alloys, and aluminum alloys. However, LMD processed parts usually do not meet end-use requirements without post treatments. In-process part quality inspection and inner features machining are impossible within a single LMD process. Hybrid additive manufacturing (HAM), which integrates additive and subtractive manufacturing in one process, has been proposed to increase the feasibility of complex parts fabrication. This dissertation aims to improve the applications of Ti-6Al-4V parts fabricated via a HAM technique. The first research topic is …

Time-Dependent Reliability Methodologies With Saddlepoint Approximation, Zhangli Hu

Doctoral Dissertations

"Engineers always encounter time-dependent uncertainties that ubiquitously exist, such as the random deterioration of material properties and time-variant loads. Therefore the reliability of engineering systems becomes time-dependent. It is crucial to predict the time-dependent reliability in the design stage, given possible catastrophic consequences of a failure. Although extensive research has been conducted on reliability analysis, estimating the reliability accurately and efficiently is still challenging. The objective of this work is to develop accurate and efficient reliability methodologies for engineering design. The basic idea is the integration of traditional reliability methods with saddlepoint approximation (SPA), which can accurately approximate the tail …

Reliability Analysis For Systems With Outsourced Components, Zhengwei Hu

Doctoral Dissertations

"The current business model for many industrial firms is to function as system integrators, depending on numerous outsourced components from outside component suppliers. This practice has resulted in tremendous cost savings; it makes system reliability analysis, however, more challenging due to the limited component information available to system designers. The component information is often proprietary to component suppliers. Motivated by the need of system reliability prediction with outsourced components, this work aims to explore feasible ways to accurately predict the system reliability during the system design stage. Four methods are proposed. The first method reconstructs component reliability functions using limited …

Laser Welding Of Metallic Glass To Crystalline Metal In Laser-Foil-Printing Additive Manufacturing, Yingqi Li

Doctoral Dissertations

"The application of metallic glasses has been traditionally limited to parts with small dimensions and simple geometries, due to the requirement of fast cooling during the conventional process of casting. In addition, joining metallic glass to crystalline metal is of interest for many applications that require locally tailored functions and properties, but it is challenging. This research describes a promising additive manufacturing technology, i.e., laser-foil-printing, to make high-quality metallic glass parts with large dimensions and complex geometries and to fabricate multi-material components from metallic glass and crystalline metal. In this research, Zr_52.5Ti₅Al₁₀Ni_14.6Cu …

Freeform Extrusion Fabrication Of Advanced Ceramics And Ceramic-Based Composites, Wenbin Li

Doctoral Dissertations

"Ceramic On-Demand Extrusion (CODE) is a recently developed freeform extrusion fabrication process for producing dense ceramic components from single and multiple constituents. In this process, aqueous paste of ceramic particles with a very low binder content ( < 1 vol%) is extruded through a moving nozzle to print each layer sequentially. Once one layer is printed, it is surrounded by oil to prevent undesirable water evaporation from the perimeters of the part. The oil level is regulated just below the topmost layer of the part being fabricated. Infrared radiation is then applied to uniformly and partially dry the top layer so that the yield stress of the paste increases to avoid part deformation. By repeating the above steps, the part is printed in a layer-wise fashion, followed by post-processing. Paste extrusion precision of different extrusion mechanisms was compared and analyzed, with an auger extruder determined to be the most suitable paste extruder for the CODE system. A novel fabrication system was developed based on a motion gantry, auger extruders, and peripheral devices. Sample specimens were then produced from 3 mol% yttria stabilized zirconia using this fabrication system, and their properties, including density, flexural strength, Young's modulus, Weibull modulus, fracture toughness, and hardness were measured. The results indicated that superior mechanical properties were achieved by the CODE process among all the additive manufacturing processes. Further development was made on the CODE process to fabricate ceramic components that have external/internal features such as overhangs by using fugitive support material. Finally, ceramic composites with functionally graded materials (FGMs) were fabricated by the CODE process using a dynamic mixing device"--Abstract, page iv.

Solvent-Free Additive Manufacturing Of Electrodes For Li-Ion Batteries, Brandon Joshua Ludwig

Doctoral Dissertations

"A new Li-ion battery electrode manufacturing process using a solvent free additive manufacturing method has been developed. Li-ion battery electrodes consist of active material particles, a binder additive, and a conductive additive. Traditionally, Li-ion battery electrodes are manufacturing using the "slurry casting" technique. In this method, the electrode materials are mixed with a solvent to create a slurry. Electrodes fabricated in this method are readily implemented for small platforms, such as portable electronics. However, this method isn't as economically viable in large platforms due to high material and manufacturing costs. High material and manufacturing costs are mostly attributed to the …

Deep Understanding Of Degradation In Lithium Ion Batteries Through Experimental And First-Principles Study, Yufang He

Doctoral Dissertations

"The growing interests in Lithium-ion Batteries (LIBs) have significantly accelerated the development of active materials. However, the key challenge is that electrode materials suffer from degradation, which include transition metal dissolution, solid electrolyte interphase (SEI) layer formation, and mechanical fracture. To address these issues, applying an ultrathin coating onto active materials via Atomic Layer Deposition (ALD) is an efficient way. Although numerious works have been done for active material performance improvement via ALD technology, the fundamental enhancement mechanisms of ALD coating on battery performance improvement are not yet known. Therefore, this dissertation consists of four papers, which focused on the …

Design, Fabrication, And Characterization Of Functionally Graded Materials, Sreekar Karnati

Doctoral Dissertations

“The aim of this research was to investigate the feasibility of fabricating custom designed, graded materials using Laser Metal Deposition (LMD) that will cater for functionality and unconventional repair. The ultimate goal of the project is to establish the versatility of LMD for fabricating advanced materials and tackling problems that have been conventionally difficult or in cases infeasible. In order to accomplish these goals, this research involved investigations into, the feasibility of using elemental powders as modular feedstocks, the feasibility of fabricating tailored gradients with these custom compositions, and finally leveraging the advantages of grading materials using LMD to successfully …

Plasmonic Metamaterial For Structural Color Printing And Spontaneous Emission Control, Wei Wang

Doctoral Dissertations

”Plasmon polaritons or plasmons are a collective oscillation movement of free electrons in metal at optical frequencies. The frequency-dependent complex dielectric function makes the metal property at optical frequencies behave totally different with that at other spectral ranges with lower frequency such as infrared and microwaves. This novel property makes the so called plasmonics or nanoplasmonics a rapid growing research field over the past few years. Many innovative concepts and applications have been developed such as perfect absorber, structural color printing, and quantum emitter spontaneous emission enhancement.

In this dissertation two of the most important applications will be addressed. The …

Plenum-To-Plenum Heat Transfer Characteristics Under Natural Circulation In A Scaled-Down Prismatic Modular Reactor, Salman Mohammed Alshehri

Doctoral Dissertations

“Gas-cooled reactor (GCR) is being developed under the Next Generation Nuclear Plant Program (NGNP) in nuclear engineering studies. As the world searches for an energy source with high energy density, clean, abundant, and storable nature to avoid global warming issues, GCR seems to be a promising solution, particularly the possibility of producing hydrogen. Studying and developing the safety analysis and GCR technologies are required for the optimum design and safety of GCR system. Multiphase Reactors Engineering and Applications Laboratory (mReal) at Missouri University of Science and Technology (S&T) has developed a natural convection heat transfer test facility with one riser …

Characterization Of Aerosols In An Underground Mine, Arash A. Habibi

Doctoral Dissertations

“Diesel-powered engines are a common source of submicron carbon-rich particles. Characterizing morphological and physical attributes of diesel agglomerates is therefore of great importance to be able to identify the source and improve removal technology. Size-segregated sampling was conducted in two phases of underground experiments. Scanning transmission electron microscopy and fast mobility particle sizers were used to determine the size distribution of agglomerates based on particle mobility and projected area diameter. Controlled zone sampling test results were used to determine the morphological characteristics of agglomerates for specific types of diesel equipment both with and without removal strategies. Changes in fractal dimension, …

Volumetric Error Compensation For Industrial Robots And Machine Tools, Le Ma

Doctoral Dissertations

“A more efficient and increasingly popular volumetric error compensation method for machine tools is to compute compensation tables in axis space with tool tip volumetric measurements. However, machine tools have high-order geometric errors and some workspace is not reachable by measurement devices, the compensation method suffers a curve-fitting challenge, overfitting measurements in measured space and losing accuracy around and out of the measured space. Paper I presents a novel method that aims to uniformly interpolate and extrapolate the compensation tables throughout the entire workspace. By using a uniform constraint to bound the tool tip error slopes, an optimal model with …

Scaleable Nanomanufacturing Of Metasurfaces Using Microsphere Photolithography, Chuang Qu

Doctoral Dissertations

“The cost-effective manufacturing of metasurfaces over large areas is a critical issue that limits their implementations. Microsphere photolithography (MPL) uses a scalable self-assembled microsphere array as an optical element to focus collimated light to nanoscale photonic jets in a photoresist layer. This dissertation investigates the fabrication capabilities, process control, and potential applications of MPL. First, the MPL concept is applied to the fabrication of metasurfaces with engineered IR absorption (e.g. perfect absorption with multiband/broadband and wavelength/polarization dependences). Improving the patterning of the photoresist requires a fundamental understanding the photochemical photonic jet interactions. The dissertation presents a model of the MPL …

Remanufacturing Of Precision Metal Components Using Additive Manufacturing Technology, Xinchang Zhang

Doctoral Dissertations

"Critical metallic components such as jet engine turbine blades and casting die/mold may be damaged after servicing for a period at harsh working environments such as elevated temperature and pressure, impact with foreign objects, wear, corrosion, and fatigue. Additive manufacturing has a promising application for the refurbishment of such high-costly parts by depositing materials at the damaged zone to restore the nominal geometry. However, several issues such as pre-processing of worn parts to assure the repairability, reconstructing the repair volume to generate a repair tool path for material deposition, and inspection of repaired parts are challenging. The current research aims …

Improvements In Digital Image Correlation And Application In Material Mechanical Test, Yunlu Zhang

Doctoral Dissertations

"Digital image correlation (DIC) is a non-contact full-field optical measurement method. With the advantages of high accuracy, low cost, and simple implementation, it has been widely applied in the area of experimental mechanics. In this study, DIC algorithm has been improved in the aspects of the pixel-level searching method and reference frame update strategy. The feature matching based method is proposed to provide an initial guess for all points of interest with semi-subpixel level accuracy in cases with small or large translation, deformation, or rotation. The bisection searching strategy is presented to automatically adjust the frame step for varying practical …

Computational Fluid Dynamics Modeling And Comparison Of Advanced Techniques For Heat Transfer Augmentation For Nuclear Applications, Salman Mohammed Alzahrani

Doctoral Dissertations

“Passive safety is the most important feature of NuScale’s reactor designs. Twist tape is one passive heat enhance heat technique. The present research investigated thermo-hydraulic characteristics of natural and forced convection of water under different configurations of twisted tape inserted in tube as well as NuScale rod bundles for uniform wall heat flux using computational fluid dynamics (CFD) using ANSYS Fluent 18.1. Results for twist tape inserted in tube under natural circulation showed that heat transfer enhanced and pressure drop increased to 28% and 102.8% over the plain tube respectively. Regularly spaced tapes, and different widths of the twisted tapes …

Soy-Based Polyurethane Foam For Insulation And Structural Applications, Gurjot S. Dhaliwal

Doctoral Dissertations

"Polyurethane (PU) foams are widely used as insulation materials due to their high insulation properties and low cost compared to conventional materials such as styrene and mineral wool. PU foams are traditionally fabricated with petroleum-based precursors. However, high crude price and higher carbon footprint has lead interest of researchers to synthesis PU foams using plant-based raw materials, that are inexpensive and renewable. In this dissertation, PU foams were fabricated using soy-based polyol and its thermal and mechanical properties were investigated. In the first part, of PU foam samples with different formulations were fabricated using soy-based polyol HB230, and varying amounts …

Laser Foil Printing And Surface Polishing Processes, Chen Chen

Doctoral Dissertations

"A foil-based additive manufacturing technology for fabricating metal parts, called Laser Foil Printing (LFP), was proposed and developed in this dissertation. The manufacturing sub-processes comprising the LFP technology were comprehensively studied, which include the laser spot welding of foil, laser raster-scan welding of foil, laser cutting of foil, and laser polishing processes. The fabricated free-form parts were demonstrated and own better mechanical properties (micro hardness and tensile strength) than the raw material, because of the rapid-cooling process of laser welding. The full and strong bond between layers was formed by the laser welding process, with no micro-cracks or pores observed. …

Fabrication And Characterization Of Advanced Materials Using Laser Metal Deposition From Elemental Powder Mixture, Xueyang Chen

Doctoral Dissertations

"Over the past decades of years, a great deal of money has been spent to machine large and complex parts from high-performance metals (i.e., titanium components for aerospace applications), so users attempt to circumvent the high cost of materials. Laser metal deposition (LMD) is an additive manufacturing technique capable of fabricating complicated structures with superior properties. This dissertation aims to improve the applications of LMD technique for manufacturing metallic components by using various elemental powder mixture according to the following three categories of research topics. The first research topic is to investigate and develop a cost-effective possibility by using elemental …