Mechanical Engineering Commons^™

Investigation Of The Iced Flowfield Characteristics Related To The Stall Margin Instrumentation Used In Icing Conditions, Erik Pederson

Dissertations

The purpose of this dissertation is to investigate the relationship between the flowfield surrounding an iced airfoil and the stall margin instrumentation developed for use in icing conditions. The stall margin system indicates to the pilot the change in available lift due to ice accretions on the leading edge of an airfoil. This system displays the change in the form of a normalized lift coefficient. Four pressure ports are chosen to specifically maintain a constant calibration curve, for pressure versus normalized lift coefficient, regardless of ice shape. This allows these pressures to be used to determine the change in maximum …

Theoretical And Experimental Studies Of The Field-Induced Phenomena In Flowing Suspensions, Nikolai Markarian

Dissertations

The present work describes results of experimental and theoretical studies of the behavior of dilute suspensions subject to high gradient AC electric fields. When a spatially non-uniform electric field is applied to a suspension, in which the particles and the suspending fluid have different dielectric permittivities andlor conductivities, the particles migrate towards the regions of high or low electric field strengths depending on the sign of their polarization. This phenomenon, referred to as dielectrophoresis, has found numerous applications for the control and manipulation of the particle motions.

Presented in Chapter 3 are the results of studying the field -induced motion …

Acoustical Characterization And Parameter Optimization Of Polymeric Noise Control Materials, Emile N. Homsi

Dissertations

The sound transmission loss (STL) characteristics of polymer-based materials are considered. Analytical models that predict, characterize and optimize the STL of polymeric materials, with respect to physical parameters that affect performance, are developed for single layer panel configuration and adapted for layered panel construction with homogenous core. An optimum set of material parameters is selected and translated into practical applications for validation.

Sound attenuating thermoplastic materials designed to be used as barrier systems in the automotive and consumer industries have certain acoustical characteristics that vary in function of the stiffness and density of the selected material. The validity and applicability …

Numerical And Experimental Investigation Of Dry Particle Coating, Ajit Mujumdar

Dissertations

Dry particle coating is an emerging field in the industries that deal with particulate products and powder processing. Compared to the widely reported experimental studies of the dry particle coating, the theoretical modeling of such processes is found to be less comprehensive. The work presented in this thesis is an attempt to fill this gap.

The first part of the dissertation aims at the numerical investigation of the hybridization system (Nara Machinery, Tokyo, Japan). The flow behavior of different materials processed in this device is analyzed using three-dimensional Discrete Element Method (DEM) as well as the computational fluid dynamics (CFD) …

Evaporating Crossflow Sprays In Gas-Solid Flows, Guangliang Liu

Dissertations

Injection of evaporating sprays into gas-solid flows is encountered in many engineering processes such as energy production industry and chemical industry. The phenomenon involves phase change, three-phase interactions, heat and mass transfer. All of these characteristics control the process efficiency, pollutant production and product quality. However, very limited studies are available on the evaporating spray jets in gas-solid flows, especially on the spray evaporation rate within a gas-solid medium. A combined study of experiments and theoretical analysis has been carried out here to investigate the fundamental mechanism of evaporating Crossflow spray jets in gas-solid flows.

In this study, in addition …

Destructive Disassembly Of Bolts And Screws Using Impact, Kyung Geun Pak

Dissertations

Disassembly, the process of separating parts or components at the end of their useful life is complex due to a variety of fastener shapes and variability in their damage during use. As a natural solution, mechanical impact has been suggested as a cost-effective method for destructive disassembly of joining elements.

The objective of this research is to improve the efficiency of impact disassembly process by studying the characteristics of elastic waves caused by impact. This research presents a new method for increasing the shear stress applied on the bolt head without increasing the energy input invested on launching striker. The …

Development Of Icejet-Based Surface Processing Technology, Dimitri V. Shishkin

Dissertations

The objective of the proposed work is to acquire knowledge needed for the development and deployment of manufacturing processes utilizing the enormous technological potential of water ice. Material removal by blasting with ice media such as particles, pellets and slugs was investigated. The ice media was accelerated by entrainment in a fluid stream (air, steam, liquid water, supercritical C0₂), impact of rotating blades, fluid expansion, etc. The ice-airjet has to replace sand blasting and the ice-waterjet has to replace the abrasive waterjet. Based on these results, technical approaches for surface processing and machining will be improved. A primary …

Concurrent Evaporating Spray Jets In Dilute Gas-Solid Pipe Flows, Xiaohua Wang

Dissertations

Evaporating spray jets into gas-solids suspensions are encountered in many industrial applications. The rapid evaporation of spray jets has significant effects on the gas-solids mixing near the jet nozzle regions, including non-uniform solids concentration dilution, gas/solids temperature reduction, and gas/solids velocity acceleration. Furthermore, the jet structure is altered by the change of solids loading, jet mass flow rate and initial droplet size distribution. These interactions of gas, solids and evaporating droplets dominate the process efficiency and product quality. There is an urgent need for exploring fundamental mechanisms of the multi-phase interactions with heat and mass transfer as there are few …

Numerical Simulation Of Mechanofusion System For Dry Particle Coating Process, Wenliang Chen

Dissertations

A numerical simulation of the Meclianofusion device for dry particle coating is carried out using Discrete Element Method (DEM) technique. In dry particle coating, tiny sub-micron guest particles are coated onto larger micron sized host particles by using mechanical forces, which the Mechanofusion device provides. It consists of a rotating cylindrical chamber that contains the powder mixture, a stationary inner piece (which has a cylindrical surface at the end), and a fixed scraper blade, which prevents powder from caking against the chamber wall. The simulation studies are performed on two scales: system scale to investigate the particle-particle and particle system …

Experimental And Numerical Study Of Flow Characteristics And Segregation In Flow Enhanced Systems, Gregory James

Dissertations

In the study of granular materials, two major topics of importance are powder flow enhancement mechanisms and the flow characterization. This dissertation is involved with both of these topics. With respect to the powder flow enhancement, this study involves investigation of two types of flow enhancement methods. The first flow enhancement method examined is a novel method called the Magnetically Assisted Powder Flow (MAPF) method. In the MAPF, small magnetic particles and powders are placed in a test hopper. A mesh is placed at the bottom of the hopper to hold the magnetic particles while the powder is discharged through …

Computation And Control Of Flow-Induced Noise Behind A Circular Cylinder Using An Acoustic Analogy Approach, Sirivit Taechajedcadarungsri

Dissertations

The computational aeroacoustics (CAA) research, which focuses on predicting acoustics by means of advanced numerical techniques, has recently gained a great deal of progress. In most applications, the prediction of both the sound source and its far-field propagation is necessary as required by regulations. Recently, powerful computers and reliable algorithms have allowed the prediction of far-field noise through the use of Computational Fluid Dynamics (CFD) data as near-field sound sources. One of the most useful analytical methods, used for the computation of noise, is Lighthill's acoustic analogy. The latter will be used in the present study.

Lighthill's acoustic analogy, combined …

Buckling Of Composite Conical Shells Under Combined Axial Compression, External Pressure, And Bending, Youngjin Chung

Dissertations

Conical shells are extensively used in space crafts, robots, shelters, domes, tanks, and in machinery or devices (e.g. as Belleville washers). Thus, the design of minimum weight, maximum strength, stiffened conical (and cylindrical) shells under combined loads has long been of interest to designers. The objective of this study is to improve the strength of conical shells and reduce the weight of the structure. Buckling of composite conical shells subjected to combined axial loading, external pressure, and bending is investigated using energy and finite element methods. The conical shells have single and multiple layers, different cone angle, length, and radius. …

Integration Of E-Business Strategy For Multi-Lifecycle Production Systems, Yanchun Luo

Dissertations

Internet use has grown exponentially on the last few years becoming a global communication and business resource. Internet-based business, or e-Business will truly affect every sector of the economy in ways that today we can only imagine. The manufacturing sector will be at the forefront of this change. This doctoral dissertation provides a scientific framework and a set of novel decision support tools for evaluating, modeling, and optimizing the overall performance of e-Business integrated multi-lifecycle production systems. The characteristics of this framework include environmental lifecycle study, environmental performance metrics, hyper-network model of integrated e-supply chain networks, fuzzy multi-objective optimization method, …

Parametric Study Of Heavy Metal Partitioning In A Pilot Scale Incinerator Burning Simulated Municipal Solid Waste, Sukrut S. Thipse

Dissertations

Incineration is a combustion process used to convert toxic waste to benign gases and residue in presence of excess air. The products of the incineration process are bottom ash, fly ash and the flue gas. Most of the metal-based phases formed in incineration are toxic and their emissions need to be strictly controlled. Therefore, behavior of metal species during incineration must be well understood. Such understanding is possible based on the experimental identification of the metal phases formed in the waste combustion and determination of their concentration in various incineration products.

A pilot-scale incinerator of 140,000 Btu/hr capacity was constructed, …

Force And Effort Analysis Of Unfastening Actions In Disassembly Processes, Manuela Sonnenberg

Dissertations

Fastening is the process of connecting one or more parts together with the aid of fastening elements. Unfastening, the reverse of fastening, is the process of separating components from each other by removing or detaching fastening elements. So far, the unfastening process is not well understood, and the analysis about it is not very extensive.

However, the need for disassembly is currently increasing. First, parts have to be taken apart for service and repair, and secondly, for the recycling process. Therefore, there is a need to consider unfastening during the design process in order to enable efficient disassemblies.

The purpose …

Study Of Automotive Hydromount Mechanism, Min Lu

Dissertations

The hydromount mechanism is studied. It was determined that the dynamic characteristics of the hydromounts are related to the rubber static stiffness, rubber damping coefficient, volumetric stiffness, and effectiveness of the oscillating fluid in the inertia track. At high frequencies the motion of the fluid in the inertia track diminishes so that its effect is negligible and may be ignored. It is also concluded that the rubber damping has a minimal effect on the hydromount dynamic properties and may be neglected. The maximum loss angle, which corresponds to the maximum damping coefficient of the hydromount, occurs near the inertia track …

Numerical Stimulation Of Stress-Induced Crystallization Of Injection Molded Semicrystalline Thermoplastics, Jianxin Guo

Dissertations

Injection molded semicrystalline plastic products exhibit variable morphology along their thickness directions. The processing conditions have a significant effect on the crystallinity distribution in the final parts. However, because of the lack of sound theoretical models for stress-induced crystallization kinetics in thermoplastics, simulations of the injection molding process of semicrystalline plastics with the consideration of stress-induced crystallization have been scarce.

A stress-induced crystallization model for semicrystalline plastics is proposed based on the theory that stress induced orientation of polymer chains increase the melting temperature of the plastics, and hence, the supercooling which is the driving force for crystallization. By assuming …

Numerical Modeling And Optimization Of Waterjet Based Surface Decontamination, Konstantin Babets

Dissertations

The mission of this study is to investigate the high-pressure waterjet based surface decontamination. Our specific objective is to develop a practical procedure for selection of process conditions at given constraints and available knowledge. This investigation is expected to improve information processing in the course of material decontamination and assist in the implementation of the waterjet decontamination technology into practice. The development of a realistic procedure for processing of a chaotic and non-accurate information constitutes the main accomplishment of this study.

The research involved acquisition of representative information about removal of brittle, elastic and viscous deposits. As a result an …

Electro-Magnetic Control Of Cylinder Wake, Zhihua Chen

Dissertations

The objective of this dissertation is to develop open and closed-loop control algorithms for manipulating wake flows past a solid cylinder in an electrically low-conducting fluid (e.g. seawater). The intent is to avoid both vortex shedding and flow separation from the body. It is desired to reduce the mean drag significantly and prevent the lift from becoming non-zero at all times. This is achieved through the introduction of a Lorentz force in the azimuthal direction generated by an array of permanent magnets and electrodes located on the solid structure. The array of actuators offers the advantage of making the Lorentz …

Kinematic Synthesis Of Adjustable Spatial Four And Five-Bar Mechanisms For Finite And Multiply Separated Positions, Kevin Russell

Dissertations

Although spatial mechanisms are more general in structure than planar mechanisms, their applications are few due to the limited number of practical design tools and the complexity of those available. It is in fact the task of the future to develop effective, but practical design tools for spatial mechanisms.

This research presents several new methods for synthesizing adjustable spatial mechanisms. The first method involves the kinematic synthesis of spatial mechanisms for multiphase motion generation. Using this method, spatial four and five-bar mechanisms can be synthesized to achieve different phases of prescribed rigid body positions. The theory of this approach has …

Numerical Studies Of Newtonian And Viscoelastic Fluids, Felix J. Alcocer

Dissertations

The direct numerical simulation (DNS) approach is used to understand the flow behavior of Newtonian and viscoelastic fluids in porous materials, four-to-one contraction and the flow of a Newtonian fluid past an airfoil.

In simulations the viscoelastic fluid is modeled by the finitely extensible nonlinear elastic (FENE) dumbbell and Oldroyd-B models. The finite element method (FEM) is used to discretize the flow domain. The DNS results show that the permeability of a periodic porous medium depends on the wavelength used for arranging particles in the direction of flow. Specifically, it is shown that for a given particle size and porosity …

Axisymetric Vibrations Of Homogeneous And Sandwich Spherical Shells With A Hole At The Center, Wai-Kwong Wong

Dissertations

Based on Hamilton's principle and the theory of elasticity, both linear and nonlinear governing equations of motion are derived for elastic spherical shells. Most of the analysis is focused on the free axisymmetric vibrations of homogeneous and sandwich shallow spherical shells. The nonlinear behavior, which allows for small deflections, is also discussed.

The linear vibrations of homogeneous and sandwich shallow spherical shells with a hole at the center are investigated with emphasis placed on the effect of thickness-shear deformation and rotatory inertia. The effects of curvature and the size of the central hole are studied for free axisymmetric motions of …

Virtual Reality Based Creation Of Concept Model Designs For Cad Systems, Bilal Yehya Maiteh

Dissertations

This work introduces a novel method to overcome most of the drawbacks in traditional methods for creating design models. The main innovation is the use of virtual tools to simulate the natural physical environment in which freeform. Design models are created by experienced designers. Namely, the model is created in a virtual environment by carving a work piece with tools that simulate NC milling cutters.

Algorithms have been developed to support the approach, in which the design model is created in a Virtual Reality (VR) environment and selection and manipulation of tools can be performed in the virtual space. The …

Rapid Tooling By Integration Of Solid Freedom Fabrication And Electrodepostion, Bo Yang

Dissertations

Rapid tooling (RT) techniques based on solid freeform fabrication (SFF) are being studied worldwide to speed up the design-production cycle and thus keep manufacturers at a competitive edge. This dissertation presents a novel rapid tooling process that integrates SFF with electrodeposition to produce molds, dies, and electrical discharge machining (EDM) electrodes rapidly, accurately and cost effectively. Experimental investigation, thermornechanical modeling and analysis, as well as case studies reveal that integration of electroforming with solid freeform fabrication is a viable way for metal tool making.

The major research tasks and results of this dissertation study are as follows:

• Rapid electroforming tooling …

Laminar Viscous Resuspension In Two-Dimensional Channels, Wenyue Yin

Dissertations

The laminar viscous resuspension of sphere particles in two-dimensional channel with gravity and electrostatic effects is studied numerically. The constitutive equation for particles include the shear-induced diffusion flux, gravitational sedimentation flux and electro-static diffusion flux. In addition the continuity equation and the momentum equations for incompressible flow are solved for developing flow using finite element method.

The parameters in this study are ratio of particle diameter to channel height d/h, Reynolds number Re, Froude number Fr, uniform inlet particle volume fraction Φ₀, and electrostatic parameter Q. The numerical simulation included d/h from 0.03 to 0.12, Re from 5 …

Simulation And Modeling Of Magnetically-Assisted Impaction Coating (Maic) Process For Dry Particle Coating, Bodhisattwa Chaudhuri

Dissertations

The objective of proposed research is to model, and understand the processes happening at multiple length and time scales in magnetically assisted impaction coating process. The smallest length scale is of the order of the molecular size and is important because during collisions the molecules rearrange themselves to form a semi-permanent bond between the core and secondary particles, which is studied by using the results of direct numerical integration of the governing Newton's equations. The effect of parameters such as size, orientation and relative velocity of particles on the collision mechanics is quantified. The largest length scale which is the …

Interaction Of A Vortex Pair And A Free-Surface : Numerical Simulation, Haisheng Ruan

Dissertations

The interaction between a submerged vortex pair with a deformable free-surface in a viscous, incompressible fluid is directly simulated and the flow is thoroughly analyzed. This is a time-dependent nonlinear free-surface problem which we solve numerically by integrating the two-dimensional Navier-Stokes equations and using boundary-fitted coordinates capable of handling large free-surface deformations. In particular, the numerical simulation of the flow at relatively high Reynolds numbers (Re = 500,1000, 2000 ) and relatively high Froude numbers (Fr = 1. 125, Fr = 2.0) is investigated and analyzed for the first time. Details are given regarding the space-time deformation of …

Reconfiguration And Tool Path Planning Of Hexapod Machine Tools, Zhenqun Li

Dissertations

Hexapod machine tools have the potential to achieve increased accuracy, speed, acceleration and rigidity over conventional machines, and are regarded by many researchers as the machine tools of the next generation. However, their small and complex workspace often limits the range of tasks they can perform, and their parallel structure raises many new issues preventing the direct use of conventional tool path planning methods. This dissertation presents an investigation of new reconfiguration and tool path planning methods for enhancing the ability of hexapods to adapt to workspace changes and assisting them in being integrated into the current manufacturing environments.

A …

Experimental Studies And Modeling Of Mechanical Properties And Morphologies Of In Situ Polymer Composites, Zhigang Li

Dissertations

In this study, a series of experiments was set up in order to analyze the morphology development and mechanical properties of poly(ethylene terephthalate) (PET)/ liquid crystalline polymer (LCP) blends. Simulations of the injection molded blends at various process conditions were performed using CMOLD. In order to determine the effect of the processing parameters on the deformation of the LCP domains during the injection molding, a new analytical method to analyze the melt flow in the advancing melt front (AMF) region was developed. By combining the simulations of the injection molding and analysis of the melt flow in the AMF region, …

Active Local Volume Displacement Cancellation Of A Vibrating Baffled Beam, Marcellin Zahui

Dissertations

An active noise control apparatus is developed. The device reduces the sound radiated from a vibrating clamped beam. The attenuation of the sound field is obtained through minimization of local volume displacements of the vibrating beam. Two single-input/single-output cancellation devices are used. Each device employs a motion sensor and an acoustic actuator. The actuator is a loudspeaker equipped with a pressure sensor to detect its volume displacement. The motion sensor signal is related to the local volume displacement of the structure which is then reduced by a loudspeaker driven with an equal but opposing volume displacement. The volume displacement sensors …