Mechanical Engineering Commons^™

Test 2237: John Deere 8rx 340, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2245: Fendt 1156 Vario Mt, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2244: Fendt 1151 Vario Mt, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2239: Kubota M8-211, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2231: John Deere 8r 250, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2084a: John Deere 7r 270, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Preperitoneal Insufflation Pressure Of The Abdominal Wall In A Porcine Model, Riley E. Reynolds, Benjamin Wankum, Sean J. Crimmins, Mark A. Carlson, Benjamin S. Terry

Department of Mechanical and Materials Engineering: Faculty Publications

Background Most complications and adverse events during laparoscopic surgery occur during initial entry into the peritoneal cavity. Among them, preperitoneal insufflation occurs when the insufflation needle is incorrectly placed, and the abdominal wall is insufflated. The objective of this study was to find a range for static pressure which is low enough to allow placement of a Veress needle into the peritoneal space without causing preperitoneal insufflation, yet high enough to separate abdominal viscera from the parietal peritoneum.

Methods A pressure test was performed on twelve fresh porcine carcasses to determine the minimum preperitoneal insufflation pressure and the minimum initial …

Nondestructive Evaluation Of Aluminium Foam Panels Subjected To Impact Loading, Gabriella Epasto, Fabio Distefano, Hozhabar Mozafari, Emanoil Linul, Vincenzo Crupi

Department of Mechanical and Materials Engineering: Faculty Publications

Aluminium foam sandwich structures have excellent energy absorption capacity, combined with good mechanical properties and low density. Some of the authors of this paper proposed an innovative Metallic Foam Shell protective device against flying ballast impact damage in railway axles. A closed-cell aluminium foam was chosen for the Metallic Foam Shell device. The main goal of this study was the experimental investigation of the impact responses of aluminium foam panels. Low velocity impact tests were carried out at different energies on different types of aluminium foam panels in order to investigate the effects of some parameters, such as core thickness, …

Surface Strengthening Of Single-Crystal Alumina By High-Temperature Laser Shock Peening, Fei Wang, X. L. Yan, Lei Liu, Michael Nastasi, Yongfeng Lu, Bai Cui

Department of Mechanical and Materials Engineering: Faculty Publications

This manuscript reports a novel process of high-temperature laser shock peening (HTLSP) for surface strengthening of single-crystal ceramics such as sapphire and reveals its fundamental mechanisms. HTLSP at 1200°C can induce a high compressive residual stress on the surface of sapphire while minimize the damage of laser-driven shock waves. Transmission electron microscopy characteriza- tions revealed high dislocation densities near the surface, suggesting that plastic deformation at an ultrahigh strain rate was generated by the high shock wave pressure. The HTLSP-induced compres- sive residual stress can significantly improve the hardness and fracture toughness of sapphire, while maintain its outstanding optical transmittance.

The Role Of Microenvironmental Cues And Mechanical Loading Milieus In Breast Cancer Cell Progression And Metastasis, Brandon D. Riehl, Eunju Kim, Tasneem Bouzid, Jung Yul Lim

Department of Mechanical and Materials Engineering: Faculty Publications

Cancer can disrupt the microenvironments and mechanical homeostatic actions in multiple scales from large tissue modification to altered cellular signaling pathway in mechanotransduction. In this review, we highlight recent progresses in breast cancer cell mechanobiology focusing on cell-microenvironment interaction and mechanical loading regulation of cells. First, the effects of microenvironmental cues on breast cancer cell progression and metastasis will be reviewed with respect to substrate stiffness, chemical/topographic substrate patterning, and 2D vs. 3D cultures. Then, the role of mechanical loading situations such as tensile stretch, compression, and flow-induced shear will be discussed in relation to breast cancer cell mechanobiology and …

Ligand Assisted Growth Of Perovskite Single Crystals With Low Defect Density, Ye Liu, Xiaopeng Zheng, Yanjun Fang, Ying Zhou, Zhenyi Ni, Xun Xiao, Shangshang Chen, Jinsong Huang

Department of Mechanical and Materials Engineering: Faculty Publications

A low defect density in metal halide perovskite single crystals is critical to achieve high performance optoelectronic devices. Here we show the reduction of defect density in per[1]ovskite single crystals grown by a ligand-assisted solution process with 3‐(decyldimethy[1]lammonio)‐propane‐sulfonate inner salt (DPSI) as an additive. DPSI ligands anchoring with lead ions on perovskite crystal surfaces not only suppress nucleation in solution, but also regulate the addition of proper ions to the growing surface, which greatly enhances the crystal quality. The grown CH₃NH₃PbI₃ crystals show better crystallinity and a 23-fold smaller trap density of 7 × 10 …

Social Connectedness And Negative Affect Uniquely Explain Individual Differences In Response To Emotional Ambiguity, Maital Neta, Rebecca L. Brock

Department of Mechanical and Materials Engineering: Faculty Publications

Negativity bias is not only central to mood and anxiety disorders, but can powerfully impact our decision-making across domains (e.g., financial, medical, social). This project builds on previous work examining negativity bias using dual-valence ambiguity. Specifically, although some facial expressions have a relatively clear negative (angry) or positive valence (happy), surprised expressions are interpreted negatively by some and positively by others, providing insight into one’s valence bias. Here, we examine putative sources of variability that distinguish individuals with a more negative versus positive valence bias using structural equation modeling. Our model reveals that one’s propensity toward negativity (operationalized as temperamental …

Direct Numerical Simulation Of A Pulsatile Flow In A Stenotic Channel Using Immersed Boundary Method, Siamak Mirfendereski, Jae Sung Park

Department of Mechanical and Materials Engineering: Faculty Publications

A three-dimensional direct numerical simulation model coupled with the immersed boundary method has been developed to simulate a pulsatile flow in a planar channel with single and double one-sided semicircular constrictions. For relevance to blood flow in large arteries, simulations have been performed at Reynolds numbers of 750 and 1000. Flow physics and resultant wall shear stress (WSS)-based hemodynamic parameters are presented. The instantaneous vortex dynamics, mean flow characteristics, and turbulent energy spectra are evaluated for flow physics. Subsequently, three WSS-based parameters, namely the time-averaged WSS, oscillatory shear index, and relative residence time, are calculated over the stenotic wall and …

Large-Scale Synthesis Of Compressible And Re-Expandable Three-Dimensional Nanofiber Matrices, Alec Mccarthy, Lorenzo Saldana, Daniel Mcgoldrick, Johnson V. John, Mitchell Kuss, Shixuan Chen, Bin Duan, Mark A. Carlson, Jingwei Xie

Department of Mechanical and Materials Engineering: Faculty Publications

Due to their biomimetic properties, electrospun nanofibers have shown great potential in many biomedical fields. However, traditionally-produced nanofibers are typically two-dimensional (2D) membranes limiting their applications. Herein, we report a large-scale synthesis of compressible and reexpandable three-dimensional (3D) nanofiber matrices for potential biomedical applications. The reproducible mass production of such matrices is achieved using a multiple-emitter electrospinning machine with a controlled environment (e.g., temperature, humidity, and air flow rate) followed by an innovative gas-foaming expansion. The modified 20-emitter circular array with 3D-printed needle caps is capable of maintaining stable Taylor cones under extremely high flow rates. The introduction of such …

Assembly Of Close-Packed Ferroelectric Polymer Nanowires Via Interface-Epitaxy With Res2, Dawei Li, Shuo Sun, Kun Wang, Zahra Ahmadi, Jeffrey E. Shield, Stephen Ducharme, Xia Hong

Department of Mechanical and Materials Engineering: Faculty Publications

The flexible, transparent, and low-weight nature of ferroelectric polymers makes them promising for wearable electronic and optical applications. To reach the full potential of the polarization-enabled device functionalities, large-scale fabrication of polymer thin films with well-controlled polar directions is called for, which remains a central challenge. The widely exploited Langmuir–Blodgett, spin-coating, and electrospinning methods only yield polymorphous or polycrystalline films, where the net polarization is compromised. Here, an easily scalable approach is reported to achieve poly(vinylidene fluoride-trifluoroethylene) P(VDF-TrFE) thin films composed of close-packed crystalline nanowires via interface-epitaxy with 1T′-ReS₂. Upon controlled thermal treatment, uniform P(VDF-TrFE) films restructure into …

Reducing Corrosion Of Additive Manufactured Magnesium Alloys By Interlayer Ultrasonic Peening, M. P. Sealy, R. Karunakaran, S. Ortgies, G. Madireddy, A. P. Malshe, K. P. Rajurkar

Department of Mechanical and Materials Engineering: Faculty Publications

Additive manufad (AM) magn alloys corrode rapidly due to tensile stress and coarse microstructures. Cyclically combining (hybridizing) additive manufacturing with interlayer ultrasonic peening was proposed as a solution to improve corrosion resistance of additive manufactured magnesium WE43 alloy through strengthening mechanisms and compressive residual stress. Applying interlayer peening work hardened discrete layers and formed a glocal integrity of regional grain refinement and subsurface compressive residual stress barriers. Tensile residual stress that typically accelerates corrosion decreased 90%. Results showed time-resolved control over corrosion was attainable by interlayer peening, and local corrosion within print cells decreased 57% with respect to as-printed WE43.

Ultra-Fast Charging In Aluminum-Ion Batteries: Electric Double Layers On Active Anode, Xuejing Shen, Tao Sun, Lei Yang, Alexey Krasnoslobodtsev, Renat F. Sabirianov, Michael P. Sealy, Wai-Ning Mei, Zhanjun Wu, Li Tan

Department of Mechanical and Materials Engineering: Faculty Publications

With the rapid iteration of portable electronics and electric vehicles, developing high-capacity batteries with ultra-fast charging capability has become a holy grail. Here we report rechargeable aluminum-ion batteries capable of reaching a high specific capacity of 200 mAh g^−1. When liquid metal is further used to lower the energy barrier from the anode, fastest charging rate of 10⁴ C (duration of 0.35 s to reach a full capacity) and 500% more specific capacity under high-rate conditions are achieved. Phase boundaries from the active anode are believed to encourage a high-flux charge transfer through the electric double layers. As …

Twinning-Assisted Dynamic Adjustment Of Grain Boundary Mobility, Qishan Huang, Qi Zhu, Yingbin Chen, Mingyu Gong, Jixue Li, Ze Zhang, Wei Yang, Jian Wang, Haofei Zhou, Jiangwei Wang

Department of Mechanical and Materials Engineering: Faculty Publications

Grain boundary (GB) plasticity dominates the mechanical behaviours of nanocrystalline materials. Under mechanical loading, GB configuration and its local deformation geometry change dynamically with the deformation; the dynamic variation of GB deformability, however, remains largely elusive, especially regarding its relation with the frequently-observed GB-associated deformation twins in nanocrystalline materials. Attention here is focused on the GB dynamics in metallic nanocrystals, by means of well-designed in situ nanomechanical testing integrated with molecular dynamics simulations. GBs with low mobility are found to dynamically adjust their configurations and local deformation geometries via crystallographic twinning, which instantly changes the GB dynamics and enhances the …

Electron Microscopy Observation Of Electric Field-Assisted Sintering Of Stainless Steel Nanoparticles, Fei Wang, Qin Zhou, Xing-Zhong Li, Yongchul Yoo, Michael Nastasi, Bai Cui

Department of Mechanical and Materials Engineering: Faculty Publications

The intrinsic role of electrical current on the electric field-assisted sintering (EFAS) process of stainless steel 316L nanoparticles has been revealed by both ex situ and in situ experiments. A novel device on the Si chip has been designed and fabricated to fit into the sample holder of a transmission electron microscope for these experiments. The evolution of nanoparticle morphology and microstructures during the EFAS process has been studied using scanning electron microscopy and transmission electron microscopy, which has been combined with the simultaneous measurement of the electric voltage and current changes. A preliminary four-stage mechanism for the EFAS process …

Fluid Modeling And Analysis Of A Mash Tl-6 Vehicle Model, Elisa Vasquez

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

The objective of this research project was to replicate the dynamic behavior of a truck-tank trailer combination vehicle using representative dimensions, properties, and inertias of the trailer/fluid ballast combination. A literature review was completed describing techniques for modeling fluids and fluid-container interactions using finite element analysis. Various fluid modeling techniques were identified, and parameters associated with those models were archived. Next, researchers utilized the tank geometry of the elliptical straight-frame 5949 trailer produced by LBT Inc. to generate a finite element mesh using finite element analysis preprocessors HyperMesh and LS PrePost. Material properties were taken from reference guides, research papers, …

Toward Understanding Underlying Mechanisms Of Drag Reduction In Turbulent Flow Control, Alex Rogge

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

The underlying mechanisms of three different flow-control strategies on drag reduction in a turbulent channel flow are investigated by direct numerical simulations. These strategies include the addition of a small concentration of long-chain polymers into a fluid, the incorporation of slip surfaces, and the application of an external body force. While it has been believed that such methods lead to a skin-friction reduction by controlling near-wall flow structures, the underlying mechanisms at play are still not as clear. In this study, a temporal analysis is employed to elucidate underlying drag-reduction mechanisms among these methods. The analysis is based on the …

Sustainable Drug Release From Polycaprolactone Coated Chitin‑Lignin Gel Fibrous Scaffolds, Turdimuhammad Abdullah, Kalamegam Gauthaman, Azadeh Mostafavi, Ahmed Alshahrie, Numan Salah, Pierfrancesco Morganti, Angelo Chianese, Ali Tamayol, Adnan Memic

Department of Mechanical and Materials Engineering: Faculty Publications

Non-healing wounds have placed an enormous stress on both patients and healthcare systems worldwide. Severe complications induced by these wounds can lead to limb amputation or even death and urgently require more effective treatments. Electrospun scaffolds have great potential for improving wound healing treatments by providing controlled drug delivery. Previously, we developed fibrous scaffolds from complex carbohydrate polymers [i.e. chitin-lignin (CL) gels]. However, their application was limited by solubility and undesirable burst drug release. Here, a coaxial electrospinning is applied to encapsulate the CL gels with polycaprolactone (PCL). Presence of a PCL shell layer thus provides longer shelf-life for the …

Machine Learning Augmentation Micro-Sensors For Smart Device Applications, Mohammad H. Hasan

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Novel smart technologies such as wearable devices and unconventional robotics have been enabled by advancements in semiconductor technologies, which have miniaturized the sizes of transistors and sensors. These technologies promise great improvements to public health. However, current computational paradigms are ill-suited for use in novel smart technologies as they fail to meet their strict power and size requirements. In this dissertation, we present two bio-inspired colocalized sensing-and-computing schemes performed at the sensor level: continuous-time recurrent neural networks (CTRNNs) and reservoir computers (RCs). These schemes arise from the nonlinear dynamics of micro-electro-mechanical systems (MEMS), which facilitates computing, and the inherent ability …

Leveraging Abet Accreditation To Promote Inclusion Of Noise Control Engineering Concepts In Engineering Programs, Lily M. Wang, Bryan Beamer

Durham School of Architectural Engineering and Construction: Faculty Publications

Accreditation Board for Engineering and Technology, Inc. (ABET) accreditation is an internationally recognized system ensuring consistency and quality in engineering education programs. As a part of ABET accreditation, there is no set requirement for any general engineering program to include noise control engineering concepts in their curricula. However, one of the seven student outcomes that each ABET accredited engineering program must document is their students’ “ability to apply engineering design to produce solutions that meet specified needs with consideration of public health, safety, and welfare…” Controlling noise in the authors’ view is a fundamental strategy for protecting workers from occupational …

Optimal Control Of Active Nematics, Michael M. Norton, Piyush Grover, Michael F. Hagan, Seth Fraden

Department of Mechanical and Materials Engineering: Faculty Publications

In this work we present the first systematic framework to sculpt active nematic systems, using optimal control theory and a hydrodynamic model of active nematics. We demonstrate the use of two different control fields, (i) applied vorticity and (ii) activity strength, to shape the dynamics of an extensile active nematic that is confined to a disk. In the absence of control inputs, the system exhibits two attractors, clockwise and counterclockwise circulating states characterized by two co-rotating topological þ1 2 defects. We specifically seek spatiotemporal inputs that switch the system from one attractor to the other; we also examine phase-shifting perturbations. …

Microfluidic Systems With Embedded Cell Culture Chambers For High Throughput Biological Assays, Arian Jaberi, Amir Monemian Esfahani, Fariba Aghabaglou, Jae Sung Park, Sidy Ndao, Ali Tamayol, Ruiguo Yang

Department of Mechanical and Materials Engineering: Faculty Publications

The ability to generate chemical and mechanical gradients on chips is important both for creating biomimetic designs or enabling high-throughput assays. However, there is still a significant knowledge gap in the generation of mechanical and chemical gradients in a single device. In this study, we developed gradient-generating microfluidic circuits with integrated microchambers to allow cell culture and to introduce chemical and mechanical gradients to cultured cells. A chemical gradient is generated across the microchambers, exposing cells to a uniform concentration of drugs. The embedded microchamber also produces a mechanical gradient in the form of varied shear stresses induced upon cells …

Effect Of Motor-Assisted Elliptical Training Speed And Body Weight Support On Center Of Pressure Movement Variability, Farahnaz Fallahtafti, Chase M. Pfeifer, Thad W. Buster, Judith M. Burnfield

Department of Mechanical and Materials Engineering: Faculty Publications

Background: A motor-assisted elliptical trainer is being used clinically to help individuals with physical disabilities regain and/or retain walking ability and cardiorespiratory fitness. Unknown is how the device’s training parameters can be used to optimize movement variability and regularity. This study examined the effect of motor-assisted elliptical training speed as well as body weight support (BWS) on center of pressure (CoP) movement variability and regularity during training. Methods: CoP was recorded using in-shoe pressure insoles as participants motor-assisted elliptical trained at three speeds (20, 40, and 60 cycles per minute) each performed at four BWS levels (0%, 20%, 40%, and …

Wavelength Decomposition Of Hybrid Additive Manufacturing Power Signals And Their Relationship With Surface Integrity, Xingtao Wang

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Additive Manufacturing (AM) has been a promising manufacturing technology in industrial applications and gained a massive amount of attention from researchers all over the world. Directed Energy Deposition (DED) is an AM process in which focused thermal energy is used to fuse materials by melting as they are deposited. One of the most significant challenges involved in current metal AM processes is improving repeatability and consistency. Substantial effort has already been invested in this area of research.

In this dissertation, a milling tool not only played a role in subtractive manufacturing but also acted as a method of monitoring the …

Comparison Of Plantar Pressure Profile Of Young Adults During Training On Elliptical Devices And Overground Walking: A Pilot Study, Guilherme Manna Cesar, Thad W. Buster, Judith M. Burnfield

Department of Mechanical and Materials Engineering: Faculty Publications

Background: Elliptical training may offer advantages over other cardiorespiratory exercises for those requiring podiatric care, since its constant double-limb support diminishes recurring high-impact plantar forces while allowing exercise in a functional, upright posture. Unknown is the impact of distinct elliptical models, that can alter user’s body mechanics, on potential variations in plantar pressure patterns.

Purpose: To compare plantar pressure variables while exercising on four ellipticals and walking.

Methods: For this cross-sectional pilot study, plantar pressure data were recorded from ten young adults while exercising on four ellipticals (True, Octane, Life Fitness, SportsArt) and walking overground. One-way repeated measures ANOVA identified …

Magnetically Induced Carrier Distribution In A Composite Rod Of Piezoelectric Semiconductors And Piezomagnetics, Guolin Wang, Jinxi Liu, Wenjie Feng, Jiashi Yang

Department of Mechanical and Materials Engineering: Faculty Publications

In this work, we study the behavior of a composite rod consisting of a piezoelectric semiconductor layer and two piezomagnetic layers under an applied axial magnetic field. Based on the phenomenological theories of piezoelectric semiconductors and piezomagnetics, a one-dimensional model is developed from which an analytical solution is obtained. The explicit expressions of the coupled fields and the numerical results show that an axially applied magnetic field produces extensional deformation through piezomagnetic coupling, the extension then produces polarization through piezoelectric coupling, and the polarization then causes the redistribution of mobile charges. Thus, the composite rod exhibits a coupling between the …