Mechanical Engineering Commons^™

Thickness-Shear And Thickness-Twist Vibrations Of Circular At-Cut Quartz Resonators, Huijing He, Jiashi Yang, Qing Jiang

Department of Mechanical and Materials Engineering: Faculty Publications

Exact solutions for free vibration frequencies and modes are obtained for thickness-shear and thickness-twist vibrations of unelectroded circular AT-cut quartz plates governed by the two-dimensional scalar differential equation derived by Tiersten and Smythe. Comparisons are made with experimental results and the widely-used perturbation solution by Tiersten and Smythe under the assumption of weak in-plane anisotropy. Our solution is found to be much closer to the experimental results than the perturbation solution . For the frequency of the fundamental thickness- shear mode, the error of the perturbation method is 0.4549%, significant in resonator applications.

Experimental Assessment Of The Impact Of Asymptomatic Gas Emboli On The Vessel Wall, Linxia Gu, Eric L. Cutler

Department of Mechanical and Materials Engineering: Faculty Publications

Quantitative evaluation of shear stress in the vessel wall due to the presence of asymptomatic gas emboli is lacking. The goal of this work was to assess the impact of chronic asymptomatic gas emboli on the risk of atherosclerosis through a custom-built cardiovascular flow simulator. Gas bubbles were created by forced air from a syringe pump. The influences of embolism injection rate, pulse rate, and time-averaged flow rate on the wall mean shear stress were investigated at resting and elevated heart rate conditions. The recorded pressure and volumetric flow rate from 24 experimental settings with four repetitions each were used …

Zone Of Intrusion For Permanent 9.1-Degree Single Slope Concrete Barriers, Cale J. Stolle

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Three WDOT 9.1-degree single-slope concrete barriers, with top heights of 36 in. (914 mm), 42 in. (1,067 mm), and 56 in. (1,422 mm) (Standard 14B32), were analyzed for Zone of Intrusion (ZOI)’ and working width using nonlinear finite element analysis (FEA). Tire-barrier friction, vehicle-barrier friction, barrier stiffness, mesh size, tire deflation, and suspension component failures were all found to have effects on simulation results. The zone of intrusion and working width were evaluated for each barrier under varying tire deflation and suspension failure conditions and determined to have a maximum value of 12.2 in. (310 mm) for the front fender …

Design Of Experimental Methods To Test The Performance Of Pads And Helmets Under Blast Loading Conditions, Kurtis Palu

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Improvised explosive devices (IEDs) have become a primary weapon in conflicts against US and allied forces. Improvements in body armor and medicine have increased the survivability of such events. These factors have caused an increase in traumatic brain injury (TBI) and mild traumatic brain injury (mTBI) induced by primary blast waves. Injury mechanisms caused from primary blast waves are not clearly understood or defined. How primary blast waves interact with materials or between narrow gaps found between helmet pads is not known. Two novel test fixtures were developed to provide a basic understanding of these two issues.

The first fixture …

High-Resolution Correlation Spectroscopy Of 13c Spins Near A Nitrogen-Vacancy Centre In Diamond, Abdelghani Laraoui, Florian Dolde, Christian Burk, Friedemann Reinhard, Jorg Wrachtrup, Carlos A. Meriles

Department of Mechanical and Materials Engineering: Faculty Publications

Spin complexes comprising the nitrogen-vacancy centre and neighbouring spins are being considered as a building block for a new generation of spintronic and quantum information processing devices. As assembling identical spin clusters is difficult, new strategies are being developed to determine individual node structures with the highest precision. Here we use a pulse protocol to monitor the time evolution of the 13C ensemble in the vicinity of a nitrogenvacancy centre. We observe long-lived time correlations in the nuclear spin dynamics, limited by nitrogen-vacancy spin–lattice relaxation. We use the host 14N spin as a quantum register and demonstrate that hyperfine-shifted resonances …

Thickness-Shear Vibration Of A Rectangular Quartz Plate With Partial Electrodes, Huijing He, Jiashi Yang, John A. Kosinski, Ji Wang

Department of Mechanical and Materials Engineering: Faculty Publications

We study free vibration of a thickness-shear mode crystal resonator of AT-cut quartz. The resonator is a rectangular plate partially and symmetrically electroded at the center with rectangular electrodes. A single-mode, three-dimensional equation governing the thickness-shear displacement is used. A Fourier series solution is obtained. Numerical results calculated from the series show that there exist trapped thickness-shear modes whose vibration is mainly under the electrodes and decays rapidly outside the electrodes. The effects of the electrode size and thickness on the trapped modes are examined.

Mechanics Of Blast Loading On Post-Mortem Human And Surrogate Heads In The Study Of Traumatic Brain Injury (Tbi) Using Experimental And Computational Approaches, Shailesh Govind Ganpule

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Blast induced neurotrauma (BINT) has been designated as the “signature injury” to warfighters in the recent military conflicts. The occurrence of traumatic brain injury (TBI) in blasts is controversial in the medical and scientific communities because the manifesting symptoms occur without visible injuries. Whether the primary blast waves alone can cause mechanical insult that is comparable to existing traumatic brain injury thresholds is still an open question, and this work is aimed to address this issue.

In the first part of this dissertation, mechanics of primary blast loading on Realistic Explosive Dummy (RED) head with and without helmets is studied …

Relationships Between Unoccupied Classroom Acoustical Conditions And Elementary Student Achievement Measured In Eastern Nebraska, Lauren M. Ronsse, Lily M. Wang

Durham School of Architectural Engineering and Construction: Faculty Publications

Building standards recommend maximum background noise levels (BNL) and reverberation times (RT) for unoccupied classrooms. However, existing research does not show a consistent correlation between these parameters and student achievement. Through in situ testing, this research seeks to determine what acoustical conditions should be attained in elementary schools for students to meet educational goals. Acoustical measurements were conducted in a Nebraska public school system and correlated to achievement scores from students in the surveyed classrooms. Unoccupied BNLs and RTs were gathered in 34 third and 33 fifth-grade classrooms. Additionally, binaural room impulse response measurements were gathered in a subset of …

Room-Temperature Organic Ferromagnetism In The Crystalline Poly(3-Hexylthiophene): Phenyl-C61-Butyric Acid Methyl Ester Blend Film, Bin Yang, Zhengguo Xiao, Yongbo Yuan, Tanjore V. Jayaraman, Jeffrey E. Shield, Ralph Skomski, Jinsong Huang

Department of Mechanical and Materials Engineering: Faculty Publications

Pronounced ferromagnetism was observed in a crystalline blend film of conjugated polymer poly(3-hexylthiophene) (P3HT) and phenyl-C61-butyric acid methyl ester (PCBM) by using magnetic force microscopy measurements. A substantial room-temperature saturation magnetization of about 0.65 emu g−1 was measured by an alternating gradient field magnetometer. Multiple experimental evidences demonstrate the charge transfer from the P3HT to the PCBM and the formation of P3HT crystal domain are expected to be two critical factors for the originals of room-temperature organic ferromagnetism.

Test 2064: Kubota M135gx, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

A Mathematical Evaluation Of Hemodynamic Parameters After Carotid Eversion And Conventional Patch Angioplasty, Alexey Kamenskiy, Iraklis I. Pipinos, Yuris A. Dzenis, Prateek K. Gupta, Syed A. Jaffar Kazmi, Jason N. Mactaggart

Department of Mechanical and Materials Engineering: Faculty Publications

Carotid endarterectomy has a long history in stroke prevention, yet controversy remains concerning optimal techniques. Two methods frequently used are endarterectomy with patch angioplasty (CEAP) and eversion endarterectomy (CEE). The objective of this study was to compare hemodynamics-related stress and strain distributions between arteries repaired using CEAP and CEE. Mathematical models were based on in vivo three-dimensional arterial geometry, pulsatile velocity profiles, and intraluminal pressure inputs obtained from 16 patients with carotid artery disease. These data were combined with experimentally derived nonlinear, anisotropic carotid artery mechanical properties to create fluid-structure interaction models of CEAP and CEE. These models were then …

Effects Of Mode Coupling On The Admittance Of An At-Cut Quartz Thickness-Shear Resonator, Huijing He, Jiashi Yang, Wei-Ping Zhang, Ji Wang

Department of Mechanical and Materials Engineering: Faculty Publications

We study the effects of couplings to flexure and face-shear modes on the admittance of an AT-cut quartz plate thickness-shear mode resonator. Mindlin’s two-dimensional equations for piezoelectric plates are employed. Electrically forced vibration solutions are obtained for three cases: pure thickness-shear mode alone; two coupled modes of thickness shear and flexure; and three coupled modes of thickness shear, flexure, and face shear. Admittance is calculated and its dependence on the driving frequency and the length/thickness ratio of the resonator is examined. Results show that near the thickness-shear resonance, admittance assumes maxima, and that for certain values of the length/thickness ratio, …

Nebraska Summary: S922 Massey Ferguson 7615, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: 913 Challenger Mt525d, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2062: Challenger Mt765d, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

A Comparative Study Of The Dry And Wet Nano-Scale Electro-Machining, M. P. Jahan, K. R. Virwani, Kamlakar P. Rajurkar, A. P. Malshe

Department of Mechanical and Materials Engineering: Faculty Publications

In recent years, a nano-electromachining (nano-EM) process based on a scanning tunneling microscope (STM) platform has been demonstrated. Nano-EM is capable of machining nano-features, under both, liquid dielectric (wet nano-EM) and air dielectric (dry nano-EM) media. The objective of this paper is to present a comparative study between the wet and dry nano-EM processes based on process mechanism, machining performance, consistency and dimensional repeatability of these two processes. The comparison of the two processes has been conducted at near field nano-EM, where the gap between the tool electrode and workpiece is 2 nm and the machining is performed at room …

Inducing Neurite Outgrowth By Mechanical Cell Stretch, Suzanne Higgins, Jeong Soon Lee, Ligyeom Ha, Jung Yul Lim

Department of Mechanical and Materials Engineering: Faculty Publications

Establishing extracellular milieus to stimulate neuronal regeneration is a critical need in neuronal tissue engineering. Many studies have used a soluble factor (such as nerve growth factor or retinoic acid [RA]), micropatterned substrate, and electrical stimulation to induce enhanced neurogenesis in neuronal precursor cells. However, little attention has been paid to mechanical stimulation because neuronal cells are not generally recognized as being mechanically functional, a characteristic of mechanoresponsive cells such as osteoblasts, chondrocytes, and muscle cells. In this study, we performed proof-of-concept experiments to demonstrate the potential anabolic effects of mechanical stretch to enhance cellular neurogenesis. We cultured human neuroblastoma …

Systems Biology Of The Functional And Dysfunctional Endothelium, Jennifer Frueh, Nataly Maimari, Takayuki Homma, Sandra M. Bovens, Ryan M. Pedrigi, Leila Towhidi, Rob Krams

Department of Mechanical and Materials Engineering: Faculty Publications

This review provides an overview of the effect of blood flow on endothelial cell (EC) signalling pathways, applying microarray technologies to cultured cells, and in vivo studies of normal and atherosclerotic animals. It is found that in cultured ECs, 5–10% of genes are up- or down-regulated in response to fluid flow, whereas only 3–6% of genes are regulated by varying levels of fluid flow. Of all genes, 90%are regulated by the steady part of fluid flow and 10% by pulsatile components. The associated gene profiles show high variability from experiment to experiment depending on experimental conditions, and importantly, the bioinformatical …

Test 2078: John Deere 6125m, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2081: John Deere 6170m, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2071: Case Ih Steiger 450 Rowtrac, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2080: John Deere 6150m, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2079: John Deere 6140m, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2072: Case Ih Steiger 450 Quadtrac, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2070: Case Ih Steiger 400 Rowtrac, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2069: Case Ih Steiger 350 Rowtrac, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2068: Versatile 400, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2067: Versatile 450, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2065: Kubota M9960, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2058: John Deere 6140d, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …