Mechanical Engineering Commons^™

Scale Models Of Acoustic Scattering Problems Including Barriers And Sound Absorption, Nan Zhang

Theses and Dissertations--Mechanical and Aerospace Engineering

Scale modeling has been commonly used for architectural acoustics but use in other noise control areas is nominal. Acoustic scale modeling theory is first reviewed and then feasibility for small-scale applications, such as is common in the electronics industry, is investigated. Three application cases are used to examine the viability. In the first example, a scale model is used to determine the insertion loss of a rectangular barrier. In the second example, the transmission loss through parallel tubes drilled through a cylinder is measured and results are compared to a 2.85 times scale model with good agreement. The third example …

NoX Formation In Light-Hydrocarbon, Premixed Flames, Robert T. Hughes

Theses and Dissertations--Mechanical and Aerospace Engineering

This study explores the reactions and related species of NO_x pollutants in methane flames in order to understand their production and consumption during the combustion process. To do this, several analytical simulations were run to explore the behavior of nitrogen species in the pre-flame, post- flame, and reaction layer regions. The results were then analyzed in order to identify all "steady-state" species in the flame as well as the determine all the unnecessary reactions and species that are not required to meet a defined accuracy. The reductions were then applied and proven to be viable.

Numerical And Experimental Techniques For Assessing The Acoustic Performance Of Duct Systems Above The Plane Wave Cutoff Frequency, Kangping Ruan

Theses and Dissertations--Mechanical and Aerospace Engineering

This research deals with determining the acoustic attenuation of heating, ventilation, and air conditioning (HVAC) ductwork. A finite element approach was developed for calculating insertion loss and breakout transmission loss. Procedures for simulating the source and receiving rooms were developed and the effect of structureborne flanking was included. Simulation results have been compared with measurements from the literature and the agreement is very good. With a good model in place, the work was extended in three ways. 1) Since measurements on full-scale equipment are difficult, scale modeling rules were developed and validated. 2) Two different numerical approaches were developed for …

Characterization Of Methane-Air Diffusion Flames For Flame Synthesis Application Through Optical Diagnostics, Zhaojin Diao

Theses and Dissertations--Mechanical and Aerospace Engineering

Flame synthesis is a growing field of research aiming at forming new materials and coatings through injection of seed materials into a flame. Accurate prediction of the thermal structure of these flames requires detailed information on the radiative properties and a thorough understanding of the governing combustion processes. The objective of this work is to establish a basic optical diagnostic characterization of different methane-air diffusion flames of different complexity. The basic principles are developed and demonstrated at a rotational symmetric co-flow burner and finally applied to a burner consisting of six clustered microflames which is designed for future flame synthesis …

Bayesian-Integrated System Dynamics Modelling For Production Line Risk Assessment, Sudhir Punyamurthula

Theses and Dissertations--Mechanical and Aerospace Engineering

Companies, across the globe are concerned with risks that impair their ability to produce quality products at a low cost and deliver them to customers on time. Risk assessment, comprising of both external and internal elements, prepares companies to identify and manage the risks affecting them. Although both external/supply chain and internal/production line risk assessments are necessary, internal risk assessment is often ignored. Internal risk assessment helps companies recognize vulnerable sections of production operations and provide opportunities for risk mitigation.

In this research, a novel production line risk assessment methodology is proposed. Traditional simulation techniques fail to capture the complex …

The Kentucky Re-Entry Universal Payload System (Krups): Sub-Orbital Flights, James Devin Sparks

Theses and Dissertations--Mechanical and Aerospace Engineering

The Kentucky Re-entry Universal Payload System (KRUPS) is an adaptable testbed for atmosphere entry science experiments, with an initial application to thermal protection systems (TPS). Because of the uniqueness of atmospheric entry conditions that ground testing is unable to replicate, scientists principally rely on numerical models for predicting entry conditions. The KRUPS spacecraft, developed at the University of Kentucky, provides an inexpensive means of obtaining validation data to verify and improve these models.

To increase the technology readiness level (TRL) of the spacecraft, two sub-orbital missions were developed. The first mission, KUDOS, launched August 13th, 2017 on a Terrier-Improved Malamute …

Assisted Development Of Mesophase Pitch With Dispersed Graphene And Its Resulting Carbon Fibers, Aaron Owen

Theses and Dissertations--Mechanical and Aerospace Engineering

The efficacy of dispersed reduced graphene oxide (rGO) as a nucleation site for the growth of mesophase in an isotropic pitch was investigated and quantified in this study. Concentrations of rGO were systematically tested in an isotropic petroleum and coal-tar pitch during thermal treatments and compared to pitch without rGO. The mesophase content of each thermally treated pitch was quantified by polarized light point counting. Further characterization of softening temperature and insolubles were quantified. Additionally, the pitches with and without rGO were melt spun, graphitized, and tensile tested to determine the effects of rGO on graphitized fiber mechanical properties and …

Design And Analysis Of A 3d-Printed, Thermoplastic Elastomer (Tpe) Spring Element For Use In Corrective Hand Orthotics, Kevin Thomas Richardson

Theses and Dissertations--Mechanical and Aerospace Engineering

This thesis proposes an algorithm that determine the geometry of 3D-printed, custom-designed spring element bands made of thermoplastic elastomer (TPE) for use in a wearable orthotic device to aid in the physical therapy of a human hand exhibiting spasticity after stroke. Each finger of the hand is modeled as a mechanical system consisting of a triple-rod pendulum with nonlinear stiffness at each joint and forces applied at the attachment point of each flexor muscle. The system is assumed quasi-static, which leads to a torque balance between the flexor tendons in the hand, joint stiffness and the design force applied to …

Multiphase Interaction In Low Density Volumetric Charring Ablators, Ali D. Omidy

Theses and Dissertations--Mechanical and Aerospace Engineering

The present thesis provides a description of historical and current modeling methods with recent discoveries within the ablation community. Several historical assumptions are challenged, namely the presence of water in Thermal Protection System (TPS) materials, presence of coking in TPS materials, non-uniform elemental production during pyrolysis reactions, and boundary layer gases, more specifically oxygen, interactions with the charred carbon interface.

The first topic assess the potential effect that water has when present within the ablator by examining the temperature prole histories of the recent flight case Mars Science Laboratory. The next topic uses experimental data to consider the instantaneous gas …

Attitude Control On So(3) With Piecewise Sinusoids, Shaoqian Wang

Theses and Dissertations--Mechanical and Aerospace Engineering

This dissertation addresses rigid body attitude control with piecewise sinusoidal signals. We consider rigid-body attitude kinematics on SO(3) with a class of sinusoidal inputs. We present a new closed-form solution of the rotation matrix kinematics. The solution is analyzed and used to prove controllability. We then present kinematic-level orientation-feedback controllers for setpoint tracking and command following.

Next, we extend the sinusoidal kinematic-level control to the dynamic level. As a representative dynamic system, we consider a CubeSat with vibrating momentum actuators that are driven by small $\epsilon$-amplitude piecewise sinusoidal internal torques. The CubeSat kinetics are derived using Newton-Euler's equations of motion. …

Discrete-Time Adaptive Control Algorithms For Rejection Of Sinusoidal Disturbances, Mohammadreza Kamaldar

Theses and Dissertations--Mechanical and Aerospace Engineering

We present new adaptive control algorithms that address the problem of rejecting sinusoids with known frequencies that act on an unknown asymptotically stable linear time-invariant system. To achieve asymptotic disturbance rejection, adaptive control algorithms of this dissertation rely on limited or no system model information. These algorithms are developed in discrete time, meaning that the control computations use sampled-data measurements. We demonstrate the effectiveness of algorithms via analysis, numerical simulations, and experimental testings. We also present extensions to these algorithms that address systems with decentralized control architecture and systems subject to disturbances with unknown frequencies.

Sustainable Living Factories For Next Generation Manufacturing, Yoram Koren, Xi Gu, Fazleena Badurdeen, Ibrahim S. Jawahir

Mechanical Engineering Faculty Publications

To be profitable and to generate sustainable value for all stakeholders, next generation manufacturers must develop capabilities to rapidly and economically respond to changing market needs while at the same time minimizing adverse impacts on the environment and benefiting society. 6R-based (Reduce, Reuse, Recycle, Recover, Redesign and Remanufacturing) sustainable manufacturing practices enable closed-loop and multi-life cycle material flow; they facilitate producing more sustainable products using manufacturing processes and systems that are more sustainable. Reconfigurable Manufacturing Systems (RMS) and its characteristics of scalability, convertibility, diagnosability, customization, modularity and integrability have emerged as a basis for living factories for next generation manufacturing …

Towards Developing Sustainable Reconfigurable Manufacturing Systems, Aihua Huang, Fazleena Badurdeen, Ibrahim S. Jawahir

Mechanical Engineering Faculty Publications

This paper aims to examine the sustainable manufacturing performance of Reconfigurable Manufacturing Systems (RMSs) using existing sustainable manufacturing metrics. RMS has six key characteristics including modularity, integrability, customization, scalability, convertibility, and diagnosability. In this paper, ‘convertibility’ is quantified by considering configuration convertibility, machine convertibility, and material handling device convertibility from the RMS perspective. In addition, the performance of RMSs with different convertibility levels is also evaluated by using sustainable manufacturing metrics. A numerical example is used to demonstrate the computational approach. Results of the analysis are used to show how sustainable manufacturing performance of RMS changes as system convertibility varies. …

Mitochondrial Dynamics And Respiration Within Cells With Increased Open Pore Cytoskeletal Meshes, David H. Jang, Sarah C. Seeger, Martha E. Grady, Frances S. Shofer, David M. Eckmann

Mechanical Engineering Faculty Publications

The cytoskeletal architecture directly affects the morphology, motility, and tensional homeostasis of the cell. In addition, the cytoskeleton is important for mitosis, intracellular traffic, organelle motility, and even cellular respiration. The organelle responsible for a majority of the energy conversion for the cell, the mitochondrion, has a dependence on the cytoskeleton for mobility and function. In previous studies, we established that cytoskeletal inhibitors altered the movement of the mitochondria, their morphology, and their respiration in human dermal fibroblasts. Here, we use this protocol to investigate applicability of power law diffusion to describe mitochondrial locomotion, assessment of rates of fission and …

Transient Analysis Of Fracture Initiation In A Coupled Thermoelastic Solid, Louis Milton Brock

Mechanical Engineering Faculty Publications

An isotropic, thermoelastic solid is initially at rest at uniform (absolute) temperature, and contains a semi-infinite, plane crack. Application of in-plane and normal point forces to each face of the crack causes transient 3D growth. The related problem of discontinuities in temperature and displacement that exist on regions that exhibit dynamic similarity is first considered. Asymptotic expressions, whose inverses are valid near the crack edges for short times, are obtained in integral transform space. These lead to equations of the Wiener–Hopf type for the fracture problem. Analytical solutions are obtained and, upon inversion, subjected to a dynamic energy release rate …

Universality Of Local Dissipation Scales In Turbulent Boundary Layer Flows With And Without Free-Stream Turbulence, Sabah F. H. Alhamdi, Sean C. C. Bailey

Mechanical Engineering Faculty Publications

Measurements of the small-scale dissipation statistics of turbulent boundary layer flows with and without free-stream turbulence are reported for Re_τ ≈ 1000 (Re_θ ≈ 2000). The scaling of the dissipation scale distribution is examined in these two boundary conditions. Results demonstrated that the local large-scale Reynolds number based on the measured longitudinal integral length scale fails to properly normalize the dissipation scale distribution near the wall in these two free-stream conditions due to the imperfect characterization of the upper bound of the inertial cascade by the integral length scale. A surrogate found from turbulent kinetic energy and …

Computational Sensitivity Investigation Of Hydrogel Injection Characteristics For Myocardial Support, Hua Wang, Christopher B. Rodell, Madonna E. Lee, Neville N. Dusaj, Joseph H. Gorman Iii, Jason A. Burdick, Robert C. Gorman, Jonathan F. Wenk

Mechanical Engineering Faculty Publications

Biomaterial injection is a potential new therapy for augmenting ventricular mechanics after myocardial infarction (MI). Recent in vivo studies have demonstrated that hydrogel injections can mitigate the adverse remodeling due to MI. More importantly, the material properties of these injections influence the efficacy of the therapy. The goal of the current study is to explore the interrelated effects of injection stiffness and injection volume on diastolic ventricular wall stress and thickness. To achieve this, finite element models were constructed with different hydrogel injection volumes (150 µL and 300 µL), where the modulus was assessed over a range of 0.1 kPa …

Rapid Characterization Of Local Shape Memory Properties Through Indentation, Peizhen Li, Haluk E. Karaca, Yang-Tse Cheng

Mechanical Engineering Faculty Publications

Shape memory alloys (SMAs) have the ability to show large recoverable shape changes upon temperature, stress or magnetic field cycling. Their shape memory, material and magnetic properties (e.g. transformation temperatures, strain, saturation magnetization and strength) determine their prospects for applications from small-scale microelectromechanical systems to large scale aerospace and biomedical systems. It should be noted that properties of SMAs are highly temperature dependent. Generally, the conventional mechanical characterization methods (e.g, tension, compression, and torsion) are used on bulk samples of SMAs to determine those properties. In this article, it will be shown that indentation technique can be used as an …

Additional Data Via Autonomous Systems To Supplement Traditional Sparse Sources For Weather Forecasting And Atmospheric Science, Suzanne Weaver Smith

Commonwealth Computational Summit

No abstract provided.

The Effect Of Inlet Pulsations On Primary Atomization Of Liquid Jets, Kyle Windland, Prashant Khare

Commonwealth Computational Summit

Objectives

• Elucidate the physics underlying the primary atomization of liquid jets.
• Investigate the effect of inlet pulsations on the atomization process.
• Identify the reliability of numerical predictions using uncertainty quantification techniques (UQ) and sensitivity analyses.

High-Fidelity Simulations Of Water Jet In Air Crossflow, Austin Johnston, Prashant Khare

Commonwealth Computational Summit

Objectives

• Investigate detailed physics underlying liquid jets in crossflow configurations applicable to various applications such as, gas-turbine, scramjet, and afterburner fuel injection.
• Develop models to predict the statistical behaviors of resulting droplets.

Note On The Rate And Energy Efficiency Limits For Additive Manufacturing, Timothy Gutowski, Sheng Jiang, Daniel Cooper, Gero Corman, Michael Hausmann, Jan-Anders Manson, Timo Schudeleit, Konrad Wegener, Matias Sabelle, Jorge Ramos-Grez, Dusan P. Sekulic

Mechanical Engineering Faculty Publications

We review the process rates and energy intensities of various additive processing technologies and focus on recent progress in improving these metrics for laser powder bed fusion processing of metals, and filament and pellet extrusion processing of polymers and composites. Over the last decade, observed progress in raw build rates has been quite substantial, with laser metal processes improving by about 1 order of magnitude, and polymer extrusion processes by more than 2 orders of magnitude. We develop simple heat transfer models that explain these improvements, point to other possible strategies for improvement, and highlight rate limits. We observe a …

Development Of An Unmanned Aerial Vehicle For The Measurement Of Turbulence In The Atmospheric Boundary Layer, Brandon M. Witte, Robert F. Singler, Sean C. C. Bailey

Mechanical Engineering Faculty Publications

This paper describes the components and usage of an unmanned aerial vehicle developed for measuring turbulence in the atmospheric boundary layer. A method of computing the time-dependent wind speed from a moving velocity sensor data is provided. The physical system built to implement this method using a five-hole probe velocity sensor is described along with the approach used to combine data from the different on-board sensors to allow for extraction of the wind speed as a function of time and position. The approach is demonstrated using data from three flights of two unmanned aerial vehicles (UAVs) measuring the lower atmospheric …

Orientation Dependent Compression Behavior Of Co35Ni35Al30 Single Crystals, Peizhen Li, Haluk E. Karaca, Yury I. Chumlyakov

Mechanical Engineering Faculty Publications

The shape memory effect (SME) and superelasticity (SE) behavior of homogenized Co₃₅Ni₃₅Al₃₀ single crystals were systematically characterized along the [100], [110] and [111] orientations under compression. The shape memory behavior of CoNiAl was found to be highly orientation and stress/temperature dependent. Maximum compressive recoverable strains were 3.98 % in [110], 3 % in [100] and 0.30 % in [111] orientations, respectively. The Co₃₅Ni₃₅Al₃₀ demonstrated a very high superelastic temperature window of more than 350 °C along the [100] and [110] orientations. Moreover, two-way shape memory effect with very low thermal …

High Resolution Imaging Of The Mitral Valve In The Natural State With 7 Tesla Mri, Sam E. Stephens, Serguei Liachenko, Neil B. Ingels, Jonathan F. Wenk, Morten O. Jensen

Mechanical Engineering Faculty Publications

Imaging techniques of the mitral valve have improved tremendously during the last decade, but challenges persist. The delicate changes in annulus shape and papillary muscle position throughout the cardiac cycle have significant impact on the stress distribution in the leaflets and chords, thus preservation of anatomically accurate positioning is critical. The aim of this study was to develop an in vitro method and apparatus for obtaining high-resolution 3D MRI images of porcine mitral valves in both the diastolic and systolic configurations with physiologically appropriate annular shape, papillary muscle positions and orientations, specific to the heart from which the valve was …

Pulsed Laser Beam Welding Of Pd43Cu27Ni10P20 Bulk Metallic Glass, Ling Shao, Amit Datye, Jiankang Huang, Jittisa Ketkaew, Sung Woo Sohn, Shaofan Zhao, Sujun Wu, Yuming Zhang, Udo D. Schwarz, Jan Schroers

Electrical and Computer Engineering Faculty Publications

We used pulsed laser beam welding method to join Pd₄₃Cu₂₇Ni₁₀P₂₀ (at.%) bulk metallic glass and characterized the properties of the joint. Fusion zone and heat-affected zone in the weld joint can be maintained completely amorphous as confirmed by X-ray diffraction and differential scanning calorimetry. No visible defects were observed in the weld joint. Nanoindentation and bend tests were carried out to determine the mechanical properties of the weld joint. Fusion zone and heat-affected zone exhibit very similar elastic moduli and hardness when compared to the base material, and the weld joint shows high …

Maximizing Operating Room Performance Using Portfolio Selection, Vivek Reddy Gunna, Amin Abedini, Wei Li

Mechanical Engineering Faculty Publications

The operating room (OR) is responsible for most hospital admissions and is one of the most cost and work intensive areas in the hospital. From recent trends, we observe an ironic parallel increase among expenditure and waiting time. Therefore, improving OR scheduling has become obligatory, particularly in terms of patient flow and benefit. Most of the hospitals rely on average patient arrivals and processing times in OR planning. But in practice, variations in arrivals and processing times causes high instability in OR performance. Our model of optimization provides OR schedules maximizing patient flow and benefit at a fixed level of …

An Optimization Model For Operating Room Scheduling To Reduce Blocking Across The Perioperative Process, Amin Abedini, Wei Li, Honghan Ye

Mechanical Engineering Faculty Publications

Operating room (OR) scheduling is important. Because of increasing demand for surgical services, hospitals must provide high quality care more efficiently with limited resources. When constructing the OR schedule, it is necessary to consider the availability of downstream resources, such as intensive care unit (ICU) and post anaesthesia care unit (PACU). The unavailability of downstream resources causes blockings between every two consecutive stages. In this paper we address the master surgical schedule (MSS) problem in order to minimize blockings between two consecutive stages. First, we present a blocking minimization (BM) model for the MSS by using integer programming, based on …

Solubility And Thermodynamic Modeling Of Carcinogenic Nitrosamines In Aqueous Amine Solvents For Co2 Capture, Jesse Thompson, Naser Matin, Kunlei Liu

Center for Applied Energy Research Faculty and Staff Publications

A better understanding of key fundamental properties of nitrosamines, including their solubility in aqueous amine solvents, is needed to understand and accurately model the vapor-phase emission levels from operating CO₂ capture systems. In this work, the first experimental Henry's volatility coefficient of a nitrosamine was obtained with a novel method using static headspace solid phase micro extraction (SPME) and gas chromatography mass spectrometry (GC/MS). The experimentally determined Henry's volatility coefficient of nitrosopyrrolidine (NPY) was found to be around 0.02 (dimensionless) at 25 °C, and falls in the range of a semi-volatile compound. A linear temperature dependency of the Henry's …

Techno-Economic Analysis Of A Secondary Air Stripper Process, J. R. Heberle, Heather Nikolic, Jesse Thompson, Kunlei Liu, Lora L. Pinkerton, David Brubaker, James C. Simpson, Song Wu, Abhoyjit S. Bhown

Center for Applied Energy Research Faculty and Staff Publications

We present results of an initial techno-economic assessment on a post-combustion CO₂ capture process developed by the Center for Applied Energy Research (CAER) at the University of Kentucky using Mitsubishi Hitachi Power Systems’ H3-1 aqueous amine solvent. The analysis is based on data collected at a 0.7 MWe pilot unit combined with laboratory data and process simulations. The process adds a secondary air stripper to a conventional solvent process, which increases the cyclic loading of the solvent in two ways. First, air strips additional CO₂ from the solvent downstream of the conventional steam-heated thermal stripper. This extra stripping …