Mechanical Engineering Commons^™

Modeling Thin Layers In Material Response Solvers, Christen Setters

Theses and Dissertations--Mechanical and Aerospace Engineering

Thermal Protection Systems (TPS) are a necessary component for atmospheric entry. Most TPS contain thin layers of various materials such as ceramic coatings, pore sealers and bonding agents. When modeling TPS, these thin layers are often neglected due to the difference in scale between the TPS (centimeters) and the thin layers (micrometers). In this study, a volume-averaging flux-conservation method is implemented in the governing equations of a finite volume material response code. The model proposes the addition of a volume and area fraction coefficient which utilizes a weighted-averaging between the amount of thin layer and heat shield material in a …

Cell And Biofilm Adhesion Strength Quantified By The Laser Spallation Technique Yields A Novel Biocompatibility Metric, The Adhesion Index, James Boyd

Theses and Dissertations--Mechanical and Aerospace Engineering

Implant associated infections are one of the leading causes of hospital acquired infections in the United States. Medical orthopedic implant devices are designed to improve adhesion of relevant cells within our body. In the case of orthopedic implants, osteoblast cells will adhere and allow for proper integration with the body’s bones. However, virulent bacteria will also adhere onto medical implants and proliferate into biofilms. Bacterial biofilms become extremely difficult to eradicate clinically as antibiotics are not as effective, resulting in severe infections or loss of implant. The aim of this research is to quantify the adhesion strength differential between relevant …

Effective Modulus Of Cracked Bodies: A Finite Element Analysis, Alan Thomas Varughese

Theses and Dissertations--Mechanical and Aerospace Engineering

This thesis considers how cracks in an elastic body can alter the body’s elastic properties. In the present study the elastic property of note is the elastic or young’s modulus. It is desired to investigate to what extent the number and orientation of cracks can cause a reduction in the elastic modulus. Because of the complex nature of the elastic fields resulting from multiple cracks interacting together in a finite geometry an analytical solution is not possible or considered. Rather the Finite Element Method is used to determine the elastic response to a body with many cracks. This provides a …

Structural Optimization Of Space Transit Vehicle Concept, Hercules, James Philip Rogers

Theses and Dissertations--Mechanical and Aerospace Engineering

STRUCTURAL OPTIMIZATION OF SPACE TRANSIT VEHICLE CONCEPT, HERCULES:

A COMPARATIVE STUDY OF STRUCTURAL OPTIONS

Hercules is a vehicle concept developed by NASA Langley's Vehicle Analysis Branch to satisfy the need for sustainable transit between Earth, the moon, and Mars. Hercules features unprecedented abort capabilities and mission flexibility to aid in NASA's Mars campaign. By utilizing modern software to perform structural analysis and optimization for a large selection of stiffened panel concepts, beam concepts, and materials trends in the structural optimization emerge. These trends will be invaluable for the design of future spacecraft needed to fulfill similar roles.

The structural optimization …

Electromagnetic Formation Control Using Frequency Multiplexing, Zahra Abbasi

Theses and Dissertations--Mechanical and Aerospace Engineering

This dissertation addresses control of relative positions and orientations of formation flying satellites using magnetic interactions. Electromagnetic formation flight (EMFF) is implemented, in which each satellite is equipped with a set of electromagnetic coils to generate an electromagnetic field. Traditional EMFF technique applies DC magnetic fields which lead to a nonlinear and highly coupled formation dynamics that allow for only position or orientation control of the satellites. We present a new frequency multiplexing method, which is a technique that uses multi-frequency sinusoidal controls, to approximately decouple the formation dynamics and to provide enough controls for both position and orientation control. …

Additive Manufacturing In Personalized Medicine: Patient-Customized Solid Dose Medicines, And Patient-Customized Wound Care Device, Amir Najarzadeh

Theses and Dissertations--Mechanical and Aerospace Engineering

Personalized Medicine - from a one-size fits all to a tailored approach is the future in pharmaceutical therapeutics and medical applications. The aim of this study is demonstrate additive manufacturing in two personalized medicine applications: 1. Patient- customized solid dose medicines, and 2. Patient-customized wound care device. The aim of the first application is to develop an inexpensive and accurate method to design and fabricate patient-customized tablets. Particularly this paper focuses on fabricating and dose controlling of patient-customized extended release prednisolone-poly(vinyle alcohole) PVA. Dry-Blending, Wet Granulation, Extrusion, Spherionization, Hot melt extrusion (HME) was adopted to produce drug loaded prednisolone-PVA filaments …

Toward Intelligent Welding By Building Its Digital Twin, Qiyue Wang

Theses and Dissertations--Electrical and Computer Engineering

To meet the increasing requirements for production on individualization, efficiency and quality, traditional manufacturing processes are evolving to smart manufacturing with the support from the information technology advancements including cyber-physical systems (CPS), Internet of Things (IoT), big industrial data, and artificial intelligence (AI). The pre-requirement for integrating with these advanced information technologies is to digitalize manufacturing processes such that they can be analyzed, controlled, and interacted with other digitalized components. Digital twin is developed as a general framework to do that by building the digital replicas for the physical entities. This work takes welding manufacturing as the case study to …

Data Generated During The 2018 Lapse-Rate Campaign: An Introduction And Overview, Gijs De Boer, Adam Houston, Jamey D. Jacob, Phillip B. Chilson, Suzanne W. Smith, Brian Argrow, Dale Lawrence, Jack Elston, David Brus, Osku Kemppinen, Petra Klein, Julie K. Lundquist, Sean Waugh, Sean C. C. Bailey, Amy E. Frazier, Michael P. Sama, Christopher Crick, David G. Schmale Iii, James Pinto, Elizabeth A. Pillar-Little, Victoria Natalie, Anders Jensen

Mechanical Engineering Faculty Publications

Unmanned aircraft systems (UASs) offer innovative capabilities for providing new perspectives on the atmosphere, and therefore atmospheric scientists are rapidly expanding their use, particularly for studying the planetary boundary layer. In support of this expansion, from 14 to 20 July 2018 the International Society for Atmospheric Research using Remotely piloted Aircraft (ISARRA) hosted a community flight week, dubbed the Lower Atmospheric Profiling Studies at Elevation – a Remotely-piloted Aircraft Team Experiment (LAPSE-RATE; de Boer et al., 2020a). This field campaign spanned a 1-week deployment to Colorado's San Luis Valley, involving over 100 students, scientists, engineers, pilots, and outreach coordinators. These …

Application Of A Small Unmanned Aerial System To Measure Ammonia Emissions From A Pilot Amine-Co2 Capture System, Travis J. Schuyler, Bradley Irvin, Keemia Abad, Jesse G. Thompson, Kunlei Liu, Marcelo I. Guzman

Chemistry Faculty Publications

The quantification of atmospheric gases with small unmanned aerial systems (sUAS) is expanding the ability to safely perform environmental monitoring tasks and quickly evaluate the impact of technologies. In this work, a calibrated sUAS is used to quantify the emissions of ammonia (NH₃) gas from the exit stack a 0.1 MWth pilot-scale carbon capture system (CCS) employing a 5 M monoethanolamine (MEA) solvent to scrub CO₂ from coal combustion flue gas. A comparison of the results using the sUAS against the ion chromatography technique with the EPA CTM-027 method for the standard emission sampling of NH_{3 …}

Experimental And Mathematical Tools To Predict Droplet Size And Velocity Distribution For A Two-Fluid Nozzle, Sadegh Poozesh, Nelson K. Akafuah, Heather R. Campbell, Faezeh Bashiri, Kozo Saito

Mechanical Engineering Faculty Publications

Despite progress in laser-based and computational tools, an accessible model that relies on fundamentals and offers a reasonably accurate estimation of droplet size and velocity is lacking, primarily due to entangled complex breakup mechanisms. Therefore, this study aims at using the integral form of the conservation equations to create a system of equations by solving which, the far-field secondary atomization can be analyzed through predicting droplet size and velocity distributions of the involved phases. To validate the model predictions, experiments are conducted at ambient conditions using water, methanol, and acetone as model fluids with varying formulation properties, such as density, …

Subsystem Identification Of Feedback And Feedforward Systems With Time Delay, S. Alireza Seyyed Mousavi, Xingye Zhang, Thomas M. Seigler, Jesse B. Hoagg

Mechanical Engineering Faculty Publications

We present an algorithm for identifying discrete-time feedback-and-feedforward subsystems with time delay that are interconnected in closed loop with a known subsystem. This frequency-domain algorithm uses only measured input and output data from a closed-loop discrete-time system, which is single input and single output. No internal signals are assumed to be measured. The orders of the unknown feedback and feedforward transfer functions are assumed to be known. We use a two-candidate-pool multi-convex-optimization approach to identify not only the feedback and feedforward transfer functions but also the feedback and feedforward time delay. The algorithm guarantees asymptotic stability of the identified closed-loop …

Dynamic Body-Weight Support To Boost Rehabilitation Outcomes In Patients With Non-Traumatic Spinal Cord Injury: An Observational Study, Justin P. Huber, Lumy Sawaki

Neurology Faculty Publications

BACKGROUND: Dynamic body-weight support (DBWS) may play an important role in rehabilitation outcomes, but the potential benefit among disease-specific populations is unclear. In this study, we hypothesize that overground therapy with DBWS during inpatient rehabilitation yields greater functional improvement than standard-of-care in adults with non-traumatic spinal cord injury (NT-SCI).

METHODS: This retrospective cohort study included individuals diagnosed with NT-SCI and undergoing inpatient rehabilitation. All participants were recruited at a freestanding inpatient rehabilitation hospital. Individuals who trained with DBWS for at least three sessions were allocated to the experimental group. Participants in the historical control group received standard-of-care (i.e., no DBWS). …

Review Of Γ’ Rafting Behavior In Nickel-Based Superalloys: Crystal Plasticity And Phase-Field Simulation, Zhiyuan Yu, Xinmei Wang, Fuqian Yang, Zhufeng Yue, James C. M. Li

Chemical and Materials Engineering Faculty Publications

Rafting is an important phenomenon of the microstructure evolution in nickel-based single crystal superalloys at elevated temperature. Understanding the rafting mechanism and its effect on the microstructure evolution is of great importance in determining the structural stability and applications of the single crystal superalloys. Phase-field method, which is an excellent tool to analyze the microstructure evolution at mesoscale, has been gradually used to investigate the rafting behavior. In this work, we review the crystal plasticity theory and phase-field method and discuss the application of the crystal plasticity theory and phase-field method in the analysis of the creep deformation and microstructure …

Laser Powder Bed Fusion Of Nitihf High-Temperature Shape Memory Alloy: Effect Of Process Parameters On The Thermomechanical Behavior, Mohammadreza Nematollahi, Guher P. Toker, Keyvan Safaei, Alejandro Hinojos, S. Ehsan Saghaian, Othmane Benafan, Michael J. Mills, Haluk E. Karaca, Mohammad Elahinia

Mechanical Engineering Faculty Publications

Laser powder bed fusion has been widely investigated for shape memory alloys, primarily NiTi alloys, with the goal of tailoring microstructures and producing complex geometries. However, processing high temperature shape memory alloys (HTSMAs) remains unknown. In our previous study, we showed that it is possible to manufacture NiTiHf HTSMA, as one of the most viable alloys in the aerospace industry, using SLM and investigated the effect of parameters on defect formation. The current study elucidates the effect of process parameters (PPs) on the functionality of this alloy. Shape memory properties and the microstructure of additively manufactured Ni-rich NiTiHf alloys were …

100% Renewable Energy Grid For Rural Electrification Of Remote Areas: A Case Study In Jordan, Loiy Al-Ghussain, Mohammad Abujubbeh, Adnan Darwish Ahmad, Ahmad M. Abubaker, Onur Taylan, Murat Fahrioglu, Nelson K. Akafuah

Institute of Research for Technology Development Faculty Publications

Many developing countries suffer from high energy-import dependency and inadequate electrification of rural areas, which aggravates the poverty problem. In this work, Al-Tafilah in Jordan was considered as a case study, where the technical, economic, and environmental benefits of a decentralized hybrid renewable energy system that can match 100% of the city demand were investigated. A tri-hybrid system of wind, solar, and hydropower was integrated with an energy storage system and optimized to maximize the match between the energy demand and production profiles. The optimization aimed at maximizing the renewable energy system (RES) fraction while keeping the levelized cost of …

Near Simultaneous Laser Scanning Confocal And Atomic Force Microscopy (Conpokal) On Live Cells, Joree N. Sandin, Surya P. Aryal, Thomas E. Wilkop, Christopher I. Richards, Martha E. Grady

Physiology Faculty Publications

Techniques available for micro- and nano-scale mechanical characterization have exploded in the last few decades. From further development of the scanning and transmission electron microscope, to the invention of atomic force microscopy, and advances in fluorescent imaging, there have been substantial gains in technologies that enable the study of small materials. Conpokal is a portmanteau that combines confocal microscopy with atomic force microscopy (AFM), where a probe "pokes" the surface. Although each technique is extremely effective for the qualitative and/or quantitative image collection on their own, Conpokal provides the capability to test with blended fluorescence imaging and mechanical characterization. Designed …

University Of Kentucky Measurements Of Wind, Temperature, Pressure And Humidity In Support Of Lapse-Rate Using Multisite Fixed-Wing And Rotorcraft Unmanned Aerial Systems, Sean C. C. Bailey, Michael P. Sama, Caleb A. Canter, Luis Felipe Pampolini, Zachary S. Lippay, Travis J. Schuyler, Jonathan D. Hamilton, Sean B. Macphee, Isaac S. Rowe, Christopher D. Sanders, Virginia G. Smith, Christina N. Vezzi, Harrison M. Wight, Jesse B. Hoagg, Marcelo I. Guzman, Suzanne Weaver Smith

Mechanical Engineering Faculty Publications

In July 2018, unmanned aerial systems (UASs) were deployed to measure the properties of the lower atmosphere within the San Luis Valley, an elevated valley in Colorado, USA, as part of the Lower Atmospheric Profiling Studies at Elevation – a Remotely-piloted Aircraft Team Experiment (LAPSE-RATE). Measurement objectives included detailing boundary layer transition, canyon cold-air drainage and convection initiation within the valley. Details of the contribution to LAPSE-RATE made by the University of Kentucky are provided here, which include measurements by seven different fixed-wing and rotorcraft UASs totaling over 178 flights with validated data. The data from these coordinated UAS flights …

An Iterative Size Effect Model Of Surface Generation In Finish Machining, Ian S. Brown, Julius M. Schoop

Mechanical Engineering Faculty Publications

In this work, a geometric model for surface generation of finish machining was developed in MATLAB, and subsequently verified by experimental surface roughness data gathered from turning tests in Ti-6Al4V. The present model predicts the behavior of surface roughness at multiple length scales, depending on feed, nose radius, tool edge radius, machine tool error, and material-dependent parameters—in particular, the minimum effective rake angle. Experimental tests were conducted on a commercial lathe with slightly modified conventional tooling to provide relevant results. Additionally, the model-predicted roughness was compared against pedigreed surface roughness data from previous efforts that included materials 51CrV4 and AL …

Characterization And Modeling Of Surface Roughness And Burr Formation In Slot Milling Of Polycarbonate, David Adeniji, Julius M. Schoop, Shehan Gunawardena, Craig Hanson, Muhammad Jahan

Mechanical Engineering Faculty Publications

Thermoplastic materials hold great promise for next-generation engineered and sustainable plastics and composites. However, due to their thermoplastic nature and viscoplastic material response, it is difficult to predict the properties of surfaces generated by machining. This is especially problematic in micro-channel machining, where burr formation and excessive surface roughness lead to poor component-surface integrity. This study attempts to model the influence of size effects, which occur due to the finite sharpness of any cutting tool, on surface finish and burr formation during micro-milling of an important thermoplastic material, polycarbonate. Experimental results show that the depth of cut does not affect …

Clinical Evaluation Of Stretchable And Wearable Inkjet-Printed Strain Gauge Sensor For Respiratory Rate Monitoring At Different Body Postures, Ala’Aldeen Al-Halhouli, Loiy Al-Ghussain, Saleem El Bouri, Fuad Habash, Haipeng Liu, Dingchang Zheng

Mechanical Engineering Graduate Research

Respiratory rate (RR) is a vital sign with continuous, convenient, and accurate measurement which is difficult and still under investigation. The present study investigates and evaluates a stretchable and wearable inkjet-printed strain gauge sensor (IJP) to estimate the RR continuously by detecting the respiratory volume change in the chest area. As the volume change could cause different strain changes at different body postures, this study aims to investigate the accuracy of the IJP RR sensor at selected postures. The evaluation was performed twice on 15 healthy male subjects (mean ± SD of age: 24 ± 1.22 years). The RR was …

The Effect Of Cutting Edge Geometry, Nose Radius And Feed On Surface Integrity In Finish Turning Of Ti-6al4v, Ian S. Brown, Julius M. Schoop

Mechanical Engineering Faculty Publications

While the respective effects of nose radius, feed and cutting edge geometry on surface integrity have each been studied at depth, coupling between these effects is not yet sufficiently understood. Recent studies have clearly established that cutting edge micro-geometries may not only have positive effects on tool-life, but can also be used to tailor surface integrity characteristics, such as surface roughness and near-surface severe plastic deformation. To further a more fundamental understanding of the effects of cutting edge micro-geometries on surface integrity, experimental turning data was generated for a varied range of cutting tool geometries and feeds. Scanning laser interferometry …

Numerical Analyses And Integration Of Split Lot Sizing Using Lean Benchmark Model For Small Lot Manufacturing In High Mix Low Volume Production, Omkar Bhosale

Theses and Dissertations--Manufacturing Systems Engineering

As the global demand for automobiles has increased rapidly over the last fifty years, customers have become more particular about the characteristics of the autos they want. This change in demand, in part has pushed manufacturing to become more flexible and created a demand for alternative, more efficient processes like the High Mix Low Volume (HMLV) production of vehicles. During HMLV, manufacturers create production lot sizes and schedule to synchronize the production processes to meet customer demand on time. The demand for the automobile parts may not be uniform or parts may not be consumed by the customer immediately, Due …

Atv Dynamics And Pediatric Rider Safety, James T. Auxier Ii

Theses and Dissertations--Biomedical Engineering

It has been observed through numerous academic and governmental agency studies that pediatric all-terrain vehicle ridership carries significant risk of injury and death. While no doubt valuable to safety, the post-hoc approach employed in these studies does little to explain the why and how behind the risk factors. Furthermore, there has been no prolonged, widespread, organized, and concerted effort to reconstruct and catalog the details and causes of the large (20,000+) number of ATV-related injuries that occur each year as has been done for road-based motor vehicle accidents. This dissertation takes the opposite approach from a meta-analysis and instead examines …

Effects Of A Hip Orthosis On Lumbopelvic Coordination In Individuals With And Without Low Back Pain, Colin Drury

Theses and Dissertations--Biomedical Engineering

Individuals with low back pain (LBP) demonstrate an abnormal lumbopelvic coordination compared to back-healthy individuals. This abnormal coordination presents itself as a reduction in lumbar contribution and an increase in pelvic contribution to trunk motion. This study investigated the ability of a hip orthosis to correct such an abnormal lumbo-pelvic coordination by restricting pelvic rotation and, as a result, increasing lumbar contributions. The effects of the hip orthosis on the magnitude and timing characteristics of lumbopelvic coordination were investigated in 20 patients with LBP and 20 asymptomatic controls. The orthosis significantly increased lumbar contributions by 11%, 5.42%, 4.84%, and 4.89% …

Correlating The Physicochemical Properties Of Magnesium Stearate With Tablet Dissolution And Lubrication, Julie L. Calahan

Theses and Dissertations--Pharmacy

Magnesium stearate (MgSt) is the most commonly used pharmaceutical excipient and is present in over half the tablet formulations on the market. In spite of its popularity as an effective lubricant, it has been repeatedly recognized that there is significant variability between MgSt samples, which can cause inconsistent lubrication between batches of MgSt. The hypothesis of this research is that the batch-to-batch variability in tablet lubrication and dissolution observed in tablet formulations containing different MgSt samples can be correlated with differences in MgSt physicochemical properties (fatty acid salt composition, crystal hydrate form, particle size and surface area). Developing correlations between …

Numerical And Experimental Studies Of Blocked Force Determination On An Offset Interface For Plate And Shell Structures And Duct Acoustic Systems, Keyu Chen

Theses and Dissertations--Mechanical and Aerospace Engineering

Blocked force determination is an alternative to the more routine method of inverse force determination using classical transfer path analysis. One advantage of determining blocked forces is that there is no need for the source to be detached or isolated from the system. Another advantage is that calculated blocked forces are appropriate when modifications are made on the receiver side of the interface. This insures that the blocked forces are suitable for utilization in analysis models where receiver system modifications are considered. Difficulties in using the approach arise when interface locations are difficult to instrument. This thesis demonstrates that blocked …

Coarse-Grained Dynamically Accurate Simulations Of Ionic Liquids At Vacuum-Interface, Tyler D. Stoffel

Theses and Dissertations--Mechanical and Aerospace Engineering

Ionic liquids, possessing improved properties in many areas of technical application, are excellent candidates as components in development of next-generation technology, including ultra-high energy batteries. If they are thus applied, however, extensive interfacial analysis of any selected ionic configuration will likely be required. Molecular dynamics (MD) provides an advantageous route by which this may be accomplished, but can fall short in observing some phenomena only present at larger time/length scales than it can simulate. Often times this is approached by coarse-graining (CG), with which scope of simulation can be significantly increased. However, coarse-grained MD systems are generally known to produce …

Modeling Thin Fluid Film On A Rotary Bell, Mark Doerre

Theses and Dissertations--Mechanical and Aerospace Engineering

A component of the mission in the Institute of Research for Technology Development at the University of Kentucky is advancing research and development and bringing it to the factory floor for continuous improvement. This dissertation delves into the art and science of rotational fluid mechanics in the context of rotary bell atomizers. One outcome proves that an approximation for calculating fluid film thicknesses on high-speed spinning surfaces inferred while working in cylindrical and spherical coordinate systems can be applied to an arbitrary bell profile. However, the analytical limits of this approximation were not investigated. In all cases, a restriction exists …

Molten Aluminum Capillary Hole-Filling, Cheng-Nien Yu

Theses and Dissertations--Mechanical and Aerospace Engineering

The presence of micrometeoroids and space debris in open space raises the question of a mitigation of the damage caused by a possible impact on the man-made structures such as space shuttles, satellites, and the International Space Station. A method achieving metallic sealed hole would be of an interest for development. This dissertation studies a surface tension driven capillary filling/sealing phenomenon in a controlled atmosphere brazing process of aluminum. The filled vs. non-filled results are predictable using minimization of energy, which shows that the outcomes depend heavily on prescribed configurations of the hole. Equilibrium models show excellent agreement with experimental …

Electrophoresis In Heterogeneous Hydrogels And Applications In Surface Patterning, Ning Ge

Theses and Dissertations--Mechanical and Aerospace Engineering

The creation of chemical micropatterns on surfaces makes it possible to add unique chemical functionality to surfaces, modifying properties such as wettability, or even adding the ability to selectively bind other molecules. The creation of biochemical surface patterning in particular is useful in a variety of fields including tissue engineering and highthroughput drug screening. There are many existing surface patterning techniques which focus on precise control over the patterned geometry, even down to submicron scale features, but they do not allow local control over chemical concentration. So the results are high resolution patterns with binary concentration. There are also existing …