Mechanical Engineering Commons^™

Six Years Of Service, Supply, And Success: Processing Harvested Ccr From Impoundments, William Fedorka, P.E.

World of Coal Ash Proceedings

No abstract provided.

Developing Single Use Deposits Of Coal Derived Fly Ash As A National Resource, Nigel Cooke

World of Coal Ash Proceedings

No abstract provided.

In-Situ Calibrated Digital Process Twin Models For Resource Efficient Manufacturing, David Adeniji, Julius Schoop

Mechanical Engineering Faculty Publications

The chief objective of manufacturing process improvement efforts is to significantly minimize process resources such as time, cost, waste, and consumed energy while improving product quality and process productivity. This paper presents a novel physics-informed optimization approach based on artificial intelligence (AI) to generate digital process twins (DPTs). The utility of the DPT approach is demonstrated in the case of finish machining of aerospace components made from gamma titanium aluminide alloy (γ-TiAl). This particular component has been plagued with persistent quality defects, including surface and sub-surface cracks, which adversely affect resource efficiency. Previous process improvement efforts have been restricted to …

Enhanced Immunoprecipitation Techniques For The Identification Of Rna-Binding Protein Partners: Igf2bp1 Interactions In Mammary Epithelial Cells, Saja A. Fakhraldeen, Scott M. Berry, David J. Beebe, Avtar Roopra, Celia M. Bisbach, Vladimir S. Spiegelman, Natalie M. Niemi, Caroline M. Alexander

Mechanical Engineering Faculty Publications

RNA-binding proteins (RBPs) regulate the expression of large cohorts of RNA species to produce programmatic changes in cellular phenotypes. To describe the function of RBPs within a cell, it is key to identify their mRNA-binding partners. This is often done by crosslinking nucleic acids to RBPs, followed by chemical release of the nucleic acid fragments for analysis. However, this methodology is lengthy, which involves complex processing with attendant sample losses, thus large amounts of starting materials and prone to artifacts. To evaluate potential alternative technologies, we tested “exclusion-based” purification of immunoprecipitates (IFAST or SLIDE) and report here that these methods …

Amplitude And Wavelength Scaling Of Sinusoidal Roughness Effects In Turbulent Channel Flow At Fixed ReΤ, Sparsh Ganju, Sean C. C. Bailey, Christoph Brehm

Mechanical Engineering Faculty Publications

Direct numerical simulations are performed for incompressible, turbulent channel flow over a smooth wall and different sinusoidal wall roughness configurations at a constant Re_τ = 720. Sinusoidal walls are used to study the effects of well-defined geometric features of roughness-amplitude, a, and wavelength, λ, on the flow. The flow in the near-wall region is strongly influenced by both a and λ. Establishing appropriate scaling laws will aid in understanding the effects of roughness and identifying the relevant physical mechanisms. Using inner variables and the roughness function to scale the flow quantities provides support for Townsend’s hypothesis, …

Volumetric Lattice Boltzmann Method For Wall Stresses Of Image-Based Pulsatile Flows, Xiaoyu Zhang, Joan Gomez-Paz, Xi Chen, James M. Mcdonough, Md Mahfuzul Islam, Yiannis Andreopoulos, Luoding Zhu, Huidan Yu

Mechanical Engineering Faculty Publications

Image-based computational fluid dynamics (CFD) has become a new capability for determining wall stresses of pulsatile flows. However, a computational platform that directly connects image information to pulsatile wall stresses is lacking. Prevailing methods rely on manual crafting of a hodgepodge of multidisciplinary software packages, which is usually laborious and error-prone. We present a new computational platform, to compute wall stresses in image-based pulsatile flows using the volumetric lattice Boltzmann method (VLBM). The novelty includes: (1) a unique image processing to extract flow domain and local wall normality, (2) a seamless connection between image extraction and VLBM, (3) an en-route …

A Novel Approach For Real-Time Quality Monitoring In Machining Of Aerospace Alloy Through Acoustic Emission Signal Transformation For Dnn, David Adeniji, Kyle Oligee, Julius Schoop

Mechanical Engineering Faculty Publications

Gamma titanium aluminide (γ-TiAl) is considered a high-performance, low-density replacement for nickel-based superalloys in the aerospace industry due to its high specific strength, which is retained at temperatures above 800 °C. However, low damage tolerance, i.e., brittle material behavior with a propensity to rapid crack propagation, has limited the application of γ-TiAl. Any cracks introduced during manufacturing would dramatically lower the useful (fatigue) life of γ-TiAl components, making the workpiece surface’s quality from finish machining a critical component to product quality and performance. To address this issue and enable more widespread use of γ-TiAl, this research aims to develop a …

A Novel Approach For Real-Time Quality Monitoring In Machining Of Aerospace Alloy Through Acoustic Emission Signal Transformation For Dnn, David Adeniji, Kyle Oligee, Julius Schoop

Mechanical Engineering Faculty Publications

Gamma titanium aluminide (γ-TiAl) is considered a high-performance, low-density replacement for nickel-based superalloys in the aerospace industry due to its high specific strength, which is retained at temperatures above 800◦C. However, low damage tolerance, i.e., brittle material behavior with a propensity to rapid crack propagation, has limited the application of γ-TiAl. Any cracks introduced during manufacturing would dramatically lower the useful (fatigue) life of γ-TiAl components, making the workpiece surface’s quality from finish machining a critical component to product quality and performance. To address this issue and enable more widespread use of γ-TiAl, this research aims to develop a real-time …

Evaluation Of The Accuracy Of Different Pv Estimation Models And The Effect Of Dust Cleaning: Case Study A 103 Mw Pv Plant In Jordan, Loiy Al-Ghussain, Moath Abu Subaih, Andres Annuk

Mechanical Engineering Graduate Research

The estimation of PV production has been widely investigated previously, where many empirical models have been proposed to account for wind and soiling effects for specific locations. However, the performance of these models varies among the investigated sites. Hence, it is vital to assess and evaluate the performance of these models and benchmark them against the common PV estimation model that accounts only for the ambient temperature. Therefore, this study aims to evaluate the accuracy and performance of four empirical wind models considering the soiling effect, and compare them to the standard model for a 103 MW PV plant in …

The Toyota Production System (Tps) In A Non-Traditional Manufacturing Environment: The Role Of Standardization In The Fast-Food Industry, Kevin Mccracken

Theses and Dissertations--Manufacturing Systems Engineering

The Toyota Production System (TPS), also known as Lean Manufacturing (LM), was founded in the automotive industry and has contributed to Toyota’s decades of success. This has brought much attention to TPS and how this system may be implemented in other industries. Focusing on the TPS foundational element of standardization, this study examines the impact of target cycle time (TCT) on process fluctuation in a fast-food environment. In order to observe the effects of TCT, team members within 3 production lines were timed. Times were measured before and after the addition of a TCT to the Standardized Work (STW) in …

Laptop Recycling Case Study: Estimating The Contained Value And Value Recovery Process Feasibility Of End-Of-Life Consumer Electronics, Zebulon Hart

Theses and Dissertations--Mining Engineering

Work has been done to establish, through the development and use of novel assay techniques and analysis metrics, the contained value of a sampling of laptop computers (as an analog for myriad e-waste sources). This work has conceptualized e-waste as an alternative to geologic-origin complex metallic ores and has likewise evaluated the feasibility of value recovery from e-waste sources in a similar manner to an ore. The application of conventional and novel mineral separation techniques to e-waste recycling processes has been evaluated and positive results are demonstrated. Further, this work has demonstrated the ability to identify the presence of base …

Modeling Human Control Behavior In Command-Following Tasks, Sajad Koushkbaghi

Theses and Dissertations--Mechanical and Aerospace Engineering

Humans interact with a variety of complex dynamic systems on a daily basis. However, they are often the lesser understood component of human-in-the-loop (HITL) systems. In this dissertation, we present the results of two HITL experiments to investigate the control strategies that humans use when performing command-following tasks. The first experiment is designed to investigate the control strategies that humans use to interact with nonlinear dynamic systems. Two groups of human subjects interact with a dynamic system and perform a command-following task. One group interacts with a linear time-invariant (LTI) dynamic system and the other group interacts with a Wiener …

Energy And Economic Modeling Of Stillage Dewatering Processes In Kentucky Bourbon Distilleries, William Brennan

Theses and Dissertations--Mechanical and Aerospace Engineering

Stillage is a byproduct of alcohol distillation and must be managed in all distilleries to sustain operations. In the United States, fuel ethanol plants typically convert all stillage into Dried Distillers’ Grains with Solubles (DDGS). This process and its variations are well known. Typical stillage management approaches are not well known, however, for the Kentucky bourbon industry. A survey of stillage management approaches in operational bourbon distilleries was conducted. Process modeling was performed to evaluate the energy and economic considerations of the available stillage dewatering methods for a 7 Million Original Proof Gallon (MMOPG) distillery. Monte Carlo simulations were performed …

Quantitative Methods For Total Lifecycle Risk Likelihood And Impact Assessment In Sustainable Product Design Decision Making, Christian Enyoghasi

Theses and Dissertations--Mechanical and Aerospace Engineering

Sustainable products promise significant economic, environmental, and societal benefits. Numerous methods are available for use during the new product development process to identify alternate product designs that optimize sustainability performance. Once any such design is selected and the product is launched, many uncertainties are likely to affect its performance over the total lifecycle. Such uncertainties give rise to risks that can influence the overall product sustainability performance. However, comprehensive quantitative methods to evaluate the likelihood or the impact of different risks to enable sustainable product design decision making are lacking.

This research aims to address this gap by developing a …

In-Situ Characterization Of Surface Quality In Γ-Tial Aerospace Alloy Machining, David Adeniji

Theses and Dissertations--Mechanical and Aerospace Engineering

The functional performance of critical aerospace components such as low-pressure turbine blades is highly dependent on both the material property and machining induced surface integrity. Many resources have been invested in developing novel metallic, ceramic, and composite materials, such as gamma-titanium aluminide (γ-TiAl), capable of improved product and process performance. However, while γ-TiAl is known for its excellent performance in high-temperature operating environments, it lacks the manufacturing science necessary to process them efficiently under manufacturing-specific thermomechanical regimes. Current finish machining efforts have resulted in poor surface integrity of the machined component with defects such as surface cracks, …

Radiative Conductivity Estimation Using Direct Approach For Fibrous Materials, Mohammad Khaleel

Theses and Dissertations--Mechanical and Aerospace Engineering

During planetary entry, space vehicles encounter high loads of thermal energy which requires a thermal protection system. Ablative thermal protection systems are usually made out of fibrous materials that exhibit internal radiation. In order to model the internal radiation response of a thermal protection system one should obtain proper radiative properties as well as thermal properties. The objective of this work is to provide a method that solves for the solid/gas thermal conductivity. Which can be used in coupled detailed radiative analysis.

Keywords: radiative conductivity, fibrous materials, radiative transfer, thermal protection system, P1 approximation, Finite Volume method.

A Decoupled Engineering Methodology For Accurate Prediction Of Ablative Surface Boundary Conditions In Thermal Protection Systems, Justin Cooper

Theses and Dissertations--Mechanical and Aerospace Engineering

The main objective of the present work is to demonstrate a method for prediction of aerothermal environments in the engineering design of hypersonic vehicles as an alternative to the current heritage method. Flat plate and stagnation point boundary layer theory require multiple assumptions to establish the current engineering paradigm. Chief among these assumptions is the similarity between mass and heat transfer. Origins of these assumptions are demonstrated and their relationship to conservative engineering design is analyzed, as well as conditions where they possibly break down. An alternative approach for assessing aerothermal environments from the fluid domain is presented, which permits …

Formation Control With Bounded Controls And Collision Avoidance: Theory And Application To Quadrotor Unmanned Air Vehicles, Zachary S. Lippay

Theses and Dissertations--Mechanical and Aerospace Engineering

This dissertation presents new results on multi-agent formation control and applies the new control algorithms to quadrotor unmanned air vehicles. First, this dissertation presents a formation control algorithm for double-integrator agents, where the formation is time varying and the agents’ controls satisfy a priori bounds (e.g., the controls accommodate actuator saturation). The main analytic results provide sufficient conditions such that all agents converge to the desired time-varying relative positions with one another and the leader, and have a priori bounded controls (if applicable). We also present results from rotorcraft experiments that demonstrate the algorithm with time-varying formations and bounded controls. …

The Effects Of Reference-Command Preview On The Strategies That Humans Use In Command-Following Tasks, Amelia J. S. Sheffler

Theses and Dissertations--Mechanical and Aerospace Engineering

This thesis presents results from an experiment in which 22 human subjects each interact with a dynamic system 40 times over a one-week period. For each interaction, a subject performs a command-following task, where the reference command is the same for all 22 subjects but different on each trial. The subjects are divided into 2 groups of 11 subjects. One group performs the command-following task without reference-command preview. The other group is provided with 1-s preview of the reference command. The experimental results are used to examine the effects of reference-command preview. For the group with 1-s reference-command preview, the …

Small-Satellite Attitude Control Using Sinusoidal Actuator Motion: Experiments On The International Space Station, K. Ryan Lush

Theses and Dissertations--Mechanical and Aerospace Engineering

In this work, we design, build, and test two 1.25U CubeSats. These small satellites were deployed on the International Space Station to perform attitude control experiments in microgravity. These CubeSats use an oscillating-mass actuation system for attitude control as opposed to traditional flywheels. Each CubeSat uses 3 pairs of servomotors to oscillate masses about 3 orthogonal axes. The servomotors have strict rotational stroke limits. Thus, they cannot spin continually. To oscillate each pair of masses, the angle of each servomotor is commanded using signals that are continuous and piecewise sinusoidal with amplitudes that do not violate the servomotor stroke constraints. …

Experimental Comparison Of Two Sampled-Data Adaptive Control Algorithms For Rejecting Sinusoidal Disturbances, William Grayson Woods

Theses and Dissertations--Mechanical and Aerospace Engineering

We review two adaptive control algorithms that address the problem of rejecting sinusoids with known frequencies that act on an unknown asymptotically stable linear time-invariant system. We present modifications to the algorithms that address the problems of sensor noise and actuator saturation. We demonstrate the effectiveness of the algorithms and compare the performance of the algorithms via numerical simulation and experimental testing.

Numerical And Scaling Study On Application Of Inkjet Technology To Automotive Coating, Masoud Arabghahestani Dr.

Theses and Dissertations--Mechanical and Aerospace Engineering

A thorough literature review identified lack of precision control over quality of droplets generated by the currently available industrial sprayers and a growing need for higher quality droplets in the coating industry. Particularly, lack of knowledge and understanding in continuous inkjets (CIJ) and drop-on-demand (DOD) technologies is identified as significant. Motivated by these needs, this dissertation is dedicated to computational fluid dynamics (CFD) and scaling studies to improve existing inkjet technologies and develop new designs of efficient coating with single and/or multiple piezoelectric sensors to produce on-demand droplets. This dissertation study aims at developing a new DOD type coating technology, …

In-Situ Characterization Of Burr Formation In Finish Machining Of Inconel 718, Hamzah M. Zannoun

Theses and Dissertations--Mechanical and Aerospace Engineering

One of the undesirable byproducts that occur during the machining process is the development of burrs, which are defined as rough excess material that forms around the geometric discontinuities of a part. Burrs are especially problematic because they have negative impacts across the triple bottom line: economic, environmental, societal. For one, they are expensive to remove because the deburring process is entirely manual and requires skill. Further, burr material is typically discarded which is adding to the already mounting waste generated from machining such as in coolant and chip disposal. Lastly, there are many societal implications, such as operator injury …

Peridynamic Material Correspondence Models: Bond-Associated And Higher-Order Formulations, Wailam Chan

Theses and Dissertations--Mechanical and Aerospace Engineering

Peridynamic material correspondence model is able to incorporate material constitutive models directly from classical continuum mechanics theory. However, conventional correspondence model faces two major technical issues for its application to practical problems. The first is the material instability, which results severe oscillations in the predicted displacement fields. The second issue is the length scale effects of materials mechanical behavior at low length scales. This research journey mainly consists of three stages. The first two stages of this research journey focus on the development of the bond-associated peridynamic material correspondence model to inherently remove the material instability. The last stage focuses …

Shape Memory Behavior Of Nitihf Alloys Fabricated By Laser Powder Bed Fusion, Guher Pelin Toker

Theses and Dissertations--Mechanical and Aerospace Engineering

NiTiHf-based alloys have emerged as potential materials for applications requiring high transformation temperatures (> 100 °C) with high strength and work output. Currently, it is challenging to produce complex shapes of these materials with tailored shape memory properties or reduce the material waste from machining operations given the cost of these materials. Additive manufacturing via Laser Powder Bed Fusion (L-PBF) represents an attractive way to fill this gap by producing unique geometries from powder-based feedstock. In this method, process parameters such as laser power, scanning speed, hatch spacing and energy density play significant roles in controlling the mechanical behavior and …

Formation Control With Collision Avoidance For Fixed-Wing Unmanned Air Vehicles With Speed Constraints, Christopher Heintz

Theses and Dissertations--Mechanical and Aerospace Engineering

Advances in the miniaturization of powerful electronic components and motors, the democratization of global navigation satellite systems (GNSS), and improvements in the performance, safety, and cost in lithium batteries has led to the proliferation of small and relatively inexpensive unmanned aerial vehicles (UAVs). Many of these UAVs are of the multi-rotor design, however, fixed-wing designs are often more efficient than rotary-wing aircraft, leading to a reduction in the power required for a UAV of a given mass to stay airborne. Autonomous cooperation between multiple UAVs would enable them to complete objectives that would be difficult or impossible for a single …

Numerical Investigation On The Effect Of Spectral Radiative Heat Transfer Within An Ablative Material, Raghava S. C. Davuluri, Rui Fu, Kaveh A. Tagavi, Alexandre Martin

Mechanical Engineering Faculty Publications

The spectral radiative heat flux could impact the material response. In order to evaluate it, a coupling scheme between KATS - MR and P1 approximation model of radiation transfer equation (RTE) is constructed and used. A Band model is developed that divides the spectral domain into small bands of unequal widths. Two verification studies are conducted: one by comparing the simulation computed by the Band model with pure conduction results and the other by comparing with similar models of RTE. The comparative results from the verification studies indicate that the Band model is computationally efficient and can be used to …

Fischer–Tropsch Synthesis: Effect Of The Promoter’S Ionic Charge And Valence Level Energy On Activity, Mirtha Z. Leguizamón León Ribeiro, Joice C. Souza, Muthu Kumaran Gnanamani, Michela Martinelli, Gabriel F. Upton, Gary Jacobs, Mauro C. Ribeiro

Center for Applied Energy Research Faculty and Staff Publications

In this contribution, we examine the effect of the promoter´s ionic charge and valence orbital energy on the catalytic activity of Fe-based catalysts, based on in situ synchrotron X-ray powder diffraction (SXRPD), temperature-programmed-based techniques (TPR, TPD, CO-TP carburization), and Fischer–Tropsch synthesis catalytic testing studies. We compared the promoting effects of K (a known promoter for longer-chained products) with Ba, which has a similar ionic radius but has double the ionic charge. Despite being partially “buried” in a crystalline BaCO₃ phase, the carburization of the Ba-promoted catalyst was more effective than that of K; this was primarily due to its …

Fully-Developed Fire Temperature In A Compartment With Varying Wood Fuel Loads, Keisuke Himoto, Masaki Noaki, Ken Matsuyama

Progress in Scale Modeling, an International Journal

Appropriate evaluation of fire behavior during the fully-developed phase is important for assessing the risk of building collapse and fire spread to adjacent buildings. In this study, a series of model experiments was conducted to investigate the fire behavior in compartments with varying wood fuel loads. Under small opening conditions, the increase in the wood fuel load had no notable effect on the heat release rate (HRR), but increased the fire duration and gas temperature. In certain cases, wood surface combustion continued even after flame ejection from the opening had ended, which maintained a high gas temperature for a long …

Fully Coupled Internal Radiative Heat Transfer For The 3d Material Response Of Heat Shield, Raghava S. C. Davuluri, Rui Fu, Kaveh A. Tagavi, Alexandre Martin

Mechanical Engineering Faculty Publications

The radiative transfer equation (RTE) is strongly coupled to the material response code KATS. A P-1 approximation model of RTE is used to account for radiation heat transfer within the material. First, the verification of the RTE model is performed by comparing the numerical and analytical solutions. Next, the coupling scheme is validated by comparing the temperature profiles of pure conduction and conduction coupled with radiative emission. The validation study is conducted on Marschall et al. cases (radiant heating, arc-jet heating, and space shuttle entry), 3D Block, 2D IsoQ sample, and Stardust Return Capsule. The validation results agree well for …