Mechanical Engineering Commons^™

Computational Fluid Dynamics Simulation Of United Launch Alliance Delta Iv Hydrogen Plume Mitigation Strategies, Stephen Guimond

Electronic Theses and Dissertations

During the launch sequence of the United Launch Alliance Delta IV launch vehicle, large amounts of pure hydrogen are introduced into the launch table and ignited by Radial-Outward-Firing-Igniters (ROFIs). This ignition results in a significant flame, or plume, that rises upwards out of the launch table due to buoyancy. The presence of the plume causes increased and unwanted heat loads on the surface of the vehicle. A proposed solution is to add a series of fans and structures to the existing launch table configuration that are designed to inject ambient air in the immediate vicinity of the launch vehicle's nozzles …

Piezospectroscopic Calibration Of Alumina-Nanocomposites For The Development Of Stress-Sensing Structures, Daniela Fugon-Dessources

Electronic Theses and Dissertations

Alpha-alumina is known to exhibit photo-luminescent (PL) properties, mainly characteristic R-lines that shift according to applied stress. In addition to showing excellent PL properties, polymers with embedded alumina nanoparticles have been shown to improve the overall composite mechanical properties. While the use of the PL properties to develop stress-sensing materials using an alumina-epoxy material has been success- fully shown in compression, the properties have not been developed for tension. In this study, the PL response of variable volume fraction alumina-epoxy composites will be determined under tensile conditions. It is expected that increasing the volume fraction of alumina nanoparticles will increase …

Response Of Electrified Micro-Jets To Electrohydrodynamic Perturbations, Weiwei Yang

Electronic Theses and Dissertations

The breakup of liquid jets is ubiquitous with rich underpinning physics and widespread applications. The natural breakup of liquid jets originates from small ambient perturbations, which can grow exponentially until the amplitude as large as the jet radius is reached. For unelectrified inviscid jets, surface energy analysis shows that only the axisymmetric perturbation is possibly unstable, and this mode is referred as varicose instability. For electrified jets, the presence of surface charge enables additional unstable modes, among which the most common one is the whipping (or kink) instability that bends and stretches the charged jet that is responsible for the …

A Study Of Compressive Sensing For Application To Structural Health Monitoring, Vaahini Ganesan

Electronic Theses and Dissertations

One of the key areas that have attracted attention in the construction industry today is Structural Health Monitoring, more commonly known as SHM. It is a concept developed to monitor the quality and longevity of various engineering structures. The incorporation of such a system would help to continuously track health of the structure, indicate the occurrence/presence of any damage in real time and give us an idea of the number of useful years for the same. Being a recently conceived idea, the state of the art technique in the field is straight forward - populating a given structure with sensors …

Mechanical And Thermal Characterization Of Continuous Fiber-Reinforced Pyrolysis-Derived Carbon-Matrix Composites, Donovan Lui

Electronic Theses and Dissertations

Maturity of high-temperature polymer-reinforced composites defer to conventionally expensive and intensive methods in both material and manufacturing aspects. Even traditional carbon-carbon, aerogel, and ceramic approaches are highly limited by difficult manufacturing techniques and are subject to sensitive handling throughout their processing and lifetime. Despite their utility in extreme environments, the high costs of existing high-temperature composites find limited practical applicability under high-performance applications. The development of continuous fiber-reinforced pyrolysis-derived carbon-matrix composites aim to circumvent the issues surrounding the manufacturing and handling of conventional high-temperature composites. Polymer matrix composites (PMCs) have a number of attractive properties including light weight, high stiffness-to-weight …

Bio-Inspired Attitude Control Of Micro Air Vehicles Using Rich Information From Airflow Sensors, He Shen

Electronic Theses and Dissertations

Biological phenomena found in nature can be learned and customized to obtain innovative engineering solutions. In recent years, biologists found that birds and bats use their mechanoreceptors to sense the airflow information and use this information directly to achieve their agile flight performance. Inspired by this phenomenon, an attitude control system for micro air vehicles using rich amount of airflow sensor information is proposed, designed and tested. The dissertation discusses our research findings on this topic. First, we quantified the errors between the calculated and measured lift and moment profiles using a limited number of micro pressure sensors over a …

Design And Development Of Heterogenous Combustion Systems For Lean Burn Applications, Anthony Terracciano

Electronic Theses and Dissertations

Combustion with a high surface area continuous solid immersed within the flame, referred to as combustion in porous media, is an innovative approach to combustion as the solid within the flame acts as an internal regenerator distributing heat from the combustion byproducts to the upstream reactants. By including the solid structure, radiative energy extraction becomes viable, while the solid enables a vast extension of flammability limits compared to conventional flames, while offering dramatically reduced emissions of NOx and CO, and dramatically increased burning velocities. Efforts documented within are used for the development of a streamlined set of design principles, and …

A Lab-Scale Experimental Framework For Studying The Phenomenon Of Autorotation, Sigitas Rimkus

Electronic Theses and Dissertations

While wind energy has emerged as a popular source of renewable energy, the traditional wind turbine has an inherent limitation, namely that it only generates power in the presence of sufficiently high and consistent wind speeds. As a result, wind farms are typically built in areas with a high probability of the required wind speeds, which are geographically sparse. One way of overcoming this drawback is to tap into the energy available in winds at high altitudes which are not only consistent and of high magnitude, but also globally pervasive. An airborne wind energy device based upon the phenomenon of …

Modeling Repair Patches Of Ship Hull And Studying The Effect Of Their Orientation On Stresses, Halima Enwegy

Electronic Theses and Dissertations

The hull is the most important structural part of any maritime vessel. It must be adequately designed to withstand the harsh sailing environmental conditions and associated forces. In the past, the basic material used to manufacture the ship hull was wood, where the hull was usually shaped as cylindrical wooden shanks. In the present, hull designs have developed to steel columns or stiffened panels that are made of different types of materials. Panels that are stiffened orthogonally in two or more directions and have nine independent material constants are defined as orthotropic panels, and they achieve high specific strength. This …

Perovskite Catalysts Enhanced Combustion On Porous Media And Thermoelectric Power Conversion, Manuel Robayo

Electronic Theses and Dissertations

A combustion chamber incorporating a high temperature porous matrix was design and tested. The effects and merits of combining combustion on porous media and catalytic enhancement were explored, in addition to the proof of concept of integrating these technologies with simple heat engines, such as thermoelectric generators, to generate efficient and reliable power. The direct observation of the flame during the combustion becomes possible due to a specially designed stainless steel chamber incorporating a quartz window where the initiation and propagation of the combustion reaction/flame was directly visible. The simple design of the combustion chamber allowed for a series of …

Modeling And Contour Control Of Multi-Axis Linear Driven Machine Tools, Ran Zhao

Electronic Theses and Dissertations

In modern manufacturing industries, many applications require precision motion control of multi-agent systems, like multi-joint robot arms and multi-axis machine tools. Cutter (end effector) should stay as close as possible to the reference trajectory to ensure the quality of the final products. In conventional computer numerical control (CNC), the control unit of each axis is independently designed to achieve the best individual tracking performance. However, this becomes less effective when dealing with multi-axis contour following tasks because of the lack of coordination among axes. This dissertation studies the control of multi-axis machine tools with focus on reducing the contour error. …

Decentralized Power Management And Transient Control In Hybrid Fuel Cell Ultra-Capacitor System, Seyed Omid Madani

Electronic Theses and Dissertations

Solid Oxide Fuel Cells (SOFCs) are considered suitable for alternative energy solutions due to advantages such as high efficiency, fuel flexibility, tolerance to impurities, and potential for combined cycle operations. One of the main operating constraints of SOFCs is fuel starvation, which can occur under fluctuating power demands. It leads to voltage loss and detrimental effects on cell integrity and longevity. In addition, reformer based SOFCs require sufficient steam for fuel reforming to avoid carbon deposition and catalyst degradation. Steam to carbon ratio (STCR) is an index indicating availability of the steam in the reformer. This work takes a holistic …

Combustion Instability Mechanism Of A Reacting Jet In Cross Flow At Gas Turbine Operating Conditions, Jared Pent

Electronic Theses and Dissertations

Modern gas turbine designs often include lean premixed combustion for its emissions benefits; however, this type of combustion process is susceptible to self-excited combustion instabilities that can lead to damaging heat loads and system vibrations. This study focuses on identifying a mechanism of combustion instability of a reacting jet in cross flow, a flow feature that is widely used in the design of gas turbine combustion systems. Experimental results from a related study are used to validate and complement three numerical tools that are applied in this study – self-excited Large Eddy Simulations, 3D thermoacoustic modeling, and 1D instability modeling. …

In-Situ Synchrotron Studies Of Turbine Blade Thermal Barrier Coatings Under Extreme Environments, Kevin Knipe

Electronic Theses and Dissertations

Thermal Barrier Coatings have been used for decades to impose a thermal gradient between the hot combustion gases and the underlying superalloy substrate in engine turbine blades. Yttria Stabilized Zirconia (YSZ) is an industry standard high temperature ceramic for turbine applications. The protective coating is adhered to the substrate using a nickel based alloy bond coat. Through exposure to high temperature, a Thermally Grown Oxide (TGO) layer develops at the bond coat-YSZ interface. Large residual stresses develop in these layers due to thermal expansion mismatch that occurs during cool down from high temperature spraying and cyclic operating conditions. Despite their …

Synchrotron X-Ray Diffraction And Piezospectroscopy Used For The Investigation Of Individual Mechanical Effects From Environmental Contaminants And Oxide Layer Undulations In Thermal Barrier Coatings, Sanna Siddiqui

Electronic Theses and Dissertations

The durability of Thermal Barrier Coatings (TBCs) used on the turbine blades of aircraft and power generation engines has been known to be affected by sand particle ingression comprised of Calcium-Magnesium-Alumina-Silicate (CMAS). Previous studies have shown that these effects present themselves through variations in the thermomechanical and thermochemical properties of the coating. This study investigated the impact of CMAS ingression on the Yttria Stabilized Zirconia Topcoat (YSZ) and Thermally Grown Oxide (TGO) strain in sprayed Thermal Barrier Coating (TBC) samples of varying porosity with and without CMAS ingression. In-Situ Synchrotron X-ray Diffraction measurements were taken on the sample under thermal …

Nanocomposite Coating Mechanics Via Piezospectroscopy, Gregory Freihofer

Electronic Theses and Dissertations

Coatings utilizing the piezospectroscopic (PS) effect of alpha alumina could enable on the fly stress sensing for structural health monitoring applications. While the PS effect has been historically utilized in several applications, here by distributing the photo-luminescent material in nanoparticle form within a matrix, a stress sensing coating is created. Parallel to developing PS coatings for stress sensing, the multi-scale mechanics associated with the observed PS response of nanocomposites and their coatings has been applied to give material property measurements, providing an understanding of particle reinforced composite behavior. Understanding the nanoparticle-coating-substrate mechanics is essential to interpreting the spectral shifts for …

An Introductory Study Of The Dynamics Of Autorotation For Wind Energy Harvesting, Bilal Salih

Electronic Theses and Dissertations

Wind turbines have been used for decades to harvest wind energy. They are suitable only to work on close to ground, and have several drawbacks that are related to the availability of the wind and the amount of extracted power compared with the cost of construction. On the other hand, there is an abundant wind power that is available at high altitudes. The wind jet streams at high elevations 8 - 12 kms are pervasive and persistent, and can potentially produce immense wind energy. Even at moderate elevations of 4 - 5 kms, wind power densities are much higher than …

Development Of Full Surface Transient Thermochromic Liquid Crystal Technique For Internal Cooling Channels, Lucky Tran

Electronic Theses and Dissertations

Proper design of high performance industrial heat transfer equipment relies on accurate knowledge and prediction of the thermal boundary conditions. In order to enhance the overall gas turbine efficiency, advancements in cooling technology for gas turbines and related applications are continuously investigated to increase the turbine inlet temperature without compromising the durability of the materials used. For detailed design, local distributions are needed in addition to bulk quantities. Detailed local distributions require advanced experimental techniques whereas they are readily available using numerical tools. Numerical predictions using a computational fluid dynamics approach with popular turbulence models are benchmarked against a semi-empirical …

Synthesis, Processing And Characterization Of Polymer Derived Ceramic Nanocomposite Coating Reinforced With Carbon Nanotube Preforms, Hongjiang Yang

Electronic Theses and Dissertations

Ceramics have a number of applications as coating material due to their high hardness, wear and corrosion resistance, and the ability to withstand high temperatures. Critical to the success of these materials is the effective heat transfer through a material to allow for heat diffusion or effective cooling, which is often limited by the low thermal conductivity of many ceramic materials. To meet the challenge of improving the thermal conductivity of ceramics without lowering their performance envelope, carbon nanotubes were selected to improve the mechanical properties and thermal dispersion ability due to its excellent mechanical properties and high thermal conductivity …

Decentralized Power Management In Microgrids, Amit Bhattacharjee

Electronic Theses and Dissertations

A large number of power sources, operational in a microgrid, optimum power sharing and accordingly controlling the power sources along with scheduling loads are the biggest challenges in modern power system. In the era of smart grid, the solution is certainly not simple paralleling. Hence it is required to develop a control scheme that delivers the overall power requirements while also adhering to the power limitations of each source. As the penetration of distributed generators increase and are diversifi ed, the choice of decentralized control becomes preferable. In this work, a decentralized control framework is conceived. The primary approach is …

Applying Best Practices To Florida Local Government Retrofit Programs, Florida Solar Energy Center, Janet Mcilvaine

FSEC Energy Research Center®

In some communities, local government and non-profit entities have funds to purchase and renovate distressed, foreclosed homes for resale in the affordable housing market. Numerous opportunities to improve whole house energy efficiency are inherent in these comprehensive renovations. BA-PIRC worked together in a multiyear field study making recommendations in individual homes, meanwhile compiling improvement costs, projected energy savings, practical challenges, and labor force factors surrounding common energy-related renovation measures. The field study, Phase 1 of this research, resulted in a set of best practices appropriate to the current labor pool and market conditions in central Florida to achieve projected annual …

Characterization Of Polyetherimide Under Static, Dynamic, And Multiple Impact Conditions, Bryan Zuanetti

HIM 1990-2015

The application of polymers in robust engineering designs is on the rise due to their excellent mechanical properties such as high fracture toughness, specific strength, durability, as well as, thermal and chemical resistances. Implementation of some advanced polymeric solids is limited due to the lack of available mechanical properties. In order for these materials to endure strenuous engineering designs it is vital to investigate their response in multiple loading rates and conditions. In this thesis, the mechanical response of polyethermide (PEI) is characterized under quasi-static, high strain rate, and multiple impact conditions. Standard tension, torsion, and compression experiments are performed …

Fracture Toughness Of A Hyperelastic Material During Surgical Cutting, Kevin Smith

HIM 1990-2015

Despite being one of the most important organs of vertebrates, the material properties of skin are also one of the most poorly understood. In the field of designing medical devices and surgical tools there are significant advantages to having a model that describes the interaction of forces between a blade tip and skin during surgical cutting. In general, skin can best be described as a composite layer consisting of a viscoelastic dermis with interwoven collagen and elastin fibers beneath a superficial epidermis. The purpose of this research is to study the fracture toughness of porcine skin during practical cutting applications, …

Development And Validation Of An Absorption Sensor For Time-Resolved Measurements Of Co And Co2, Kyle Thurmond

HIM 1990-2015

A sensor was developed for simultaneous measurements of carbon monoxide and carbon dioxide fluctuations in internal combustion engine exhaust gases. This sensor utilizes low-cost and compact LEDs that emit in the 3-5[micro]m wavelength range which are more appropriate for practical applications than the more traditionally used lasers. An affordable, fast response sensor that can measure these gases has broad application that can lead to more efficient, fuel flexible engines and regulations of harmful emissions. LEDs have a more spectrally broad and diverging emission than lasers which presented many design challenges. The optical design software ZEMAX was utilized to overcome these …

Flexible Residential Test Facility: Impact Of Infiltration And Ventilation On Measured Heating Season Energy And Moisture Levels, Florida Solar Energy Center, Danny Parker

FSEC Energy Research Center®

Perhaps no residential topic has been discussed as much among building scientists as air infiltration and required mechanical ventilation. Usually, envelope tightening is recommended as an efficiency strategy for retrofitting an existing home. In humid climates, reducing infiltration can reduce summer moisture loads. However, during drier weather when the air conditioner is not running, lower infiltration can lead to potential condensation. Even though severe cold weather is rare in the Deep South, the prevalence of single-pane windows can lead to condensation events.

Energy And Economic Optimization To Achieve Near Zero Energy Homes In Europe: Implications Of Inclusion Of Lighting And Appliances, Florida Solar Energy Center, Danny Parker

FSEC Energy Research Center®

Achieving annual net zero energy use in homes has been demonstrated as feasible in dozens of monitored projects in the United States.[1] In particular, very low energy use homes in Europe have been proven within the Passivhaus approach.[2] Achieving 'nearly zero energy buildings' (NZEB) has also been established as a vital objective over the next decade within the European Union (EU) (Boermans et al., 2011). However, reaching this result at the lowest possible cost remains a key challenge around the world. Balancing renewable power generation with energy efficiency will be vital in Europe as anticipated by Voss, Musall and Lichtmeß.[4] …

Technical Subtopic 2.1: Modeling Variable Refrigerant Flow Heat Pump And Heat Recovery Equipment In Energyplus, Florida Solar Energy Center, Richard Raustad

FSEC Energy Research Center®

The University of Central Florida/Florida Solar Energy Center, in cooperation with the Electric Power Research Institute and several variable-refrigerant-flow air conditioning (VRF AC) manufacturers, provided a detailed computer model for a VRF AC system in the United States Department of Energy's (U.S. DOE) EnergyPlus' building energy simulation tool. No other simulation tool currently has the capability to accurately model this state-of-the-art VRF heating, ventilating, and air conditioning (HVAC) equipment. Detailed laboratory testing and field demonstrations were performed to measure equipment performance and compare this performance with that predicted by the use of this new model through computer simulation.

This project …

Current Best Practices For High Performance, Deep Energy Retrofits In Florida Affordable Housing, Florida Solar Energy Center, Janet Mcilvaine

FSEC Energy Research Center®

In the fall of 2009, researchers at the Florida Solar Energy Center (FSEC) began working with affordable housing entities that were conducting major renovation projects in unoccupied, foreclosed homes. The study was funded by the Florida Energy Systems Consortium and the U.S. Department of Energy's Building America program. When components and equipment were being replaced because they were worn out, researchers provided savings projections for higher-efficiency choices. Savings were also projected for improvements that were strictly for energy efficiency, such as adding ceiling insulation. The best practices summarized in this document are a mixture of assessment, design, specification, quality assurance, …

Hers Index Scores As An Alternative Compliance Path For The 2015 Iecc, Florida Solar Energy Center, Philip W. Fairey

FSEC Energy Research Center®

The analysis presented here is an extension of a previous study on HERS Index Scores as they relate to various version of the International Energy Conservation Code (IECC) by the same author. This extension of the previous study is designed to examine the impact of advanced, ultra-high efficiency appliances and high efficiency HVAC systems on HERS Index Scores as they relate to reductions in the HERS Index Scores that may be used as 'tradeoffs' against best practice envelope efficiencies.

A Simplified Approach To Thermomechanical Fatigue And Application To V-Shaped Notches, Thomas Bouchenot

HIM 1990-2015

A vast array of high value parts in land- and air-based turbomachinery are subjected to non-isothermal cycling in the presence of mechanical loading. Crack initiation, growth and eventual failure more significantly reduce life in these components compared to isothermal conditions. More accurate simulation of the stress and strain evolution at critical locations of components, as well as test specimens, can lead to a more accurate prediction of remaining life to a structural integrity specialists. The focus of this thesis is to characterize the effects of thermomechanical fatigue (TMF) on generic turbomachinery alloy. An expression that can be used to estimate …