Mechanical Engineering Commons^™

The Status Of Gas-Lubricated Bearings, Bhaskar Dattatraya Shiwalkar

Masters Theses

"The idea of gas-lubricated bearings was suggested as far back as 1854 by Hirn, but it is only very recently that they have aroused a great amount of interest. The interest is centered on the advantages of gas-bearings for the following major applications:

1. High temperature lubrication where ordinary liquid or grease lubrication fails.
2. Bearings operating in radio-active atmospheres where conventional lubrication may break down.
3. Applications sensitive to contamination where fouling from lubricating oil becomes serious.
4. Low-friction devices--an especially important advantage because of the trend to high speed machinery.
5. Applications where positional accuracies down to micro-inches are required.

As a result …

The Determination Of The Heat Transfer Film Coefficients Of Internally Heated And Twisted Strips, Karpurapu Venkata Apparao

Masters Theses

"As the demand for power supply is increasing, the power from nuclear fission is assuming an important role in the field of power production. The enormous quantity of heat generated during the fission process can be utilized for the generation of power. To get maximum advantage out of the fission process, the fission material must be fabricated into a unit of proper shape to permit the control of the process and safe removal of heat generated. This unit, composed of fuel elements is known as the reactor core and is one of the major concerns in nuclear power development.

The …

The Effect Of Boundry Layer Control By Passing Fluid Through Transverse Slots On Heat Transfer From A Pipe, Perakatte Joseph George

Masters Theses

"The object of this work is an experimental investigation into the possibility of obtaining an increase in the forced convection heat transfer coefficient for a pipe by passing the fluid through narrow transverse slots cut in the pipe, and thereby altering the boundary layer pattern.

Since the greatest barrier to the flow of heat from a solid to liquid exists at the boundary layer, it can be expected that any device which will alter the boundary layer pattern will alter the heat transfer coefficient. When mass crosses a boundary layer in a direction perpendicular to the main motion of the …

Effect Of Boundry Layer Control, Through Surface Holes, On The Film Coefficient Of Convective Heat Transfer, Jainti Prasad

Masters Theses

"This thesis has as its objective, the effect of some boundary layer control on the convective heat transfer film coefficient, metal to liquid. The boundary layer control was produced by drilling 1/16 inch diameter holes on the tube surface.

In this modern world of atoms and the current development of large quantities of its energy at low cost, the subject of designing heat exchange devices of higher efficiency is receiving considerable attention. In a reactor, or any type of heat exchange device, there are limits for the temperatures of a heat exchange surface because of corrosion, strength of metals etc. …

An Experimental Study Of The Effects Of Additives On The Collapsibility Of Carbon Dioxode-Sodium Silicate Bonded Foundry Cores, Robert G. Liptai

Masters Theses

"Every foundry is searching for methods and tools to raise product quality and production while lowering cost. In early 1954 published articles on the new carbon dioxide-sodium silicate process of core hardening began to stir the imagination of most of the foundries throughout the United States, This process has probably claimed more space in the foundry journals than any other subject, hailed by some as a cure-all and dismissed by others as unsatisfactory.

The list of advantages of this process was impressive, but anyone associated with the process was confronted with daily problems that had to be solved regardless of …

Critical Load For A Rectangular Plate Simply Supported On Three Edges, Built In On The Fourth Edge, And Compressed On Two Opposite Simply Supported Edges By A Load In The Plane Of The Plate, Bert Louis Smith

Masters Theses

"There are many engineering structures in which thin plates are used extensively, some examples of which can be found in ship and airplane structures, bridges, etc. The problem contained in this thesis is the analysis of a thin rectangular plate simply supported on three edges, built in on the fourth edge, and compressed on two opposite simply supported edges by a load in the plane or the plate. This problem becomes one of stability, and the object of the solution is to find the smallest load that will cause the plate to buckle"--Introduction, page vi.

Electronic Three-Phase Wave Generator, Don Cronin

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The present invention relates to electric signal generators, and more particularly to an electronic three-phase Wave generator.

Bonded Joint Strength Versus Loading Rate, Charless William Fowlkes

Masters Theses

"The purpose of this investigation was to determine the influence of the rate of loading variable on the apparent shear strengths of joints bonded with some of the currently available metal-to-metal adhesives. The effects of this variable are sometimes neglected by testing laboratories. The results of an experimental evaluation of the mechanical behavior of a group on modern metal-to-metal adhesives as a function of the rate of load application are used to more accurately establish the importance of rate of load considerations in adhesive joint testing. An attempt is made to explain observations of other investigators engaged in adhesive joint …

Steady State Temperature Distribution In A Rotating Disk, George Henry Morgan

Masters Theses

"The purpose of this investigation was to obtain an expression for the steady state temperature distribution of a disk of uniform thickness rotating at a constant speed in ambient air while absorbing heat through the periphery at a constant rate. Engineers encounter such problems in connection with brakes of several varieties. The general solution obtained here could be extended to similar physical problems such as grinding wheels, disk clutches, and so on.

A differential equation was obtained for the temperature in the disk by the application of Fourier's conduction law and Newton’s convection law. A solution of this equation was …

Unsteady State Heat Transfer From A Hot Body To A Liquid, Larry Clinton Atha

Masters Theses

"The problem investigated in this thesis is that of unsteady state heat transfer from a hot body to a liquid, a quenching problem. Unsteady state or transient heat transfer is heat transfer in which the temperature distribution changes with time.

If a hot body was suddenly quenched in a large mass of liquid, a film of vapor would form between the hot body and the liquid. For example, if a hot body was quenched in water a film of steam would form between the hot body and the water. It is the purpose of this thesis to determine the heat …

Stability Of Rectangular Plates By Arbitrary Deflection Method, James Arthur Jones

Masters Theses

"Many engineering structures use thin rectangular plates as members. These plates may be loaded and supported in numerous ways. The edges may be freely supported, rigidly supported, or supported by elastic members. The load may be applied normal to the plane of the plate, in which case the problem becomes essentially one of bending. If the load is applied in the plane of the plate, placing it in compression, the problem becomes one of stability.

This investigation is concerned with the stability of plates rigidly supported on all edges and having a compressive load applied to two opposite edges of …

Generator Control System Employing Semiconductor Apparatus, Don Cronin

Mechanical and Aerospace Engineering Faculty Research & Creative Works

This invention relates generally to new and improved transistor control apparatus for controlling the excitation of rotary generators. In the field of transistor control of generators, especially where it is desired to control relatively large field excitation currents, the problem arises of obtaining suitable transistors having a sufficiently large current carrying capacity to properly control the current flowing in the generator exciting field. It has been found that the answer does not lie in paralleling two or more transistors directly, since only by extremely carefully matching of transistors or by utilizing auxiliary electronic components in the circuit can it be …

Performance Characteristics Of A Tubular Regenerative Heat Exchanger, Harry J. Sauer Jr.

Masters Theses

"The term regenerator is widely used to define any type of heat exchanger in which the heat is alternately stored and removed...The present investigation is concerned with the calculation of the characteristics of the "single-blow", tubular regenerative heater, its dimensions and performance. In the analysis in this thesis, the heat is considered to be stored in bundles of tubes initially preheated by hot gases flowing through the heater and subsequently cooled by the flow of air. This paper makes no attempt to deal with the effects of radiation from the outer row of tubes to the heater shell"--Introduction, page 1-3.

Frost Formation And Its Influence Upon Heat Transfer, Jack Lewis Loper

Masters Theses

"The cooling of a gas-vapor mixture or a mixture of several vapors, in the general case, results in condensation (phase-change) of one or more of the vapors when their respective dew-points are reached. This results in a mass transfer of the vapor to the cooling surface accompanied by energy transfer as the vapor gives up its latent heat of vaporization to the surface and becomes a liquid. The liquid accumulation adds a resistance to the further transfer of mass and energy unless some means is provided for its removal from the surface, such as gravity action.

In this paper we …

Surface Temperature Measurement Of Metal Undergoing Induction Heating, Ding-Yee Nee

Masters Theses

"It is the object of this thesis to investigate the possibility of using thermoelectric pyrometry for surface temperature measurement of metal undergoing induction heating. The temperature range under investigation, as stated before, is 400 °F to 1250 °F. This research may actually be treated by two sections.

The first section concerns the methods of using thermocouples for ordinary surface temperature measurements. The second section concerns the effect, if any, on thermocouple e.m.f. readings while it is measuring the surface temperature of a metal undergoing induction heating. The first section of the investigation has been well covered by literature and will …

The Stability Of Rectangular Plates With Built-In Supports At The Edges, John Bruce Miles

Masters Theses

"The purpose of this investigation is to derive an expression for the critical stress for a thin rectangular plate with compressive edge loading. The load is applied on two opposite edges with the remaining two edges built-in. (See Fig. 1) This is essentially a stability problem.

Rectangular plates with compressive edge loading and various edge restraints appear in a number of engineering structures. Bulkheads of ships could be so classified, as could certain components of fabricated beams and columns. The new supersonic B-58 bomber developed by Convair has a honeycomb wing structure dictated by heat conduction requirements. This, too, involves …

Naval Shipyard Workload Distribution, Leonard Charles Wolff

Professional Degree Theses

"In developing the subject of Naval Shipyard workload distribution emphasis will be given to the functions performed by the Workload Planning Branch of the Bureau of Ships, Navy Department, Washington, D. C.

If the naval ship repair and conversion workload for the next few years was firm, and if the workload remained constant, and if sufficient funds were available for the work, and if plans, materials and equipment were available, and if the employment level to accomplish the work assigned to the naval shipyards remained constant, the Bureau of Ships' problem of scheduling work would be minimized. The only problem …

The Closure Of Thin Wall Pressure Vessels, Archie W. Culp Jr.

Masters Theses

"The object of this thesis is to find various methods of closing thin wall aluminum cylinders. Such a closure must be strong enough, that when internal pressure is applied, ultimate failure will occur along a longitudinal element of the cylinder and not at the closure. Moreover, such a method must not only be mechanically sound, but it must be readily adaptable to mass production"--Introduction.

Heat Flow In A Two-Dimensional Steady-Flow System Without Radial Symmetry, George H. Parharoglu

Masters Theses

"As the extent of the science of heat conduction depends on the multiplicity of the boundary conditions that can be applied to the basic differential equation, a particular case in which the use of one set boundary conditions for the development of the general equation for the temperature distribution as well as the the amount of heat flow in a steady-state, two-dimensional heat flow system with a source of heat plased at the center of or along the axis of a cylinder, and without radial symmetry has been the object of this problem. Radial symmetry means the variation of temperature …

Metallurgical Pulp Mill Processing For The White Pine Copper Company Project, White Pine, Michigan, Steve Theodorides

Professional Degree Theses

No abstract provided.

Crimp Method Of Closure Of Small Pressure Vessels, Zafiri Bersu

Masters Theses

"The object of this thesis is to design a means of closing the ends of thin aluminum alloy tubing in the 1” O.D. to 2” O.D. by .035 to .065 inch thick sizes, so that the closure will withstand internal hydrostatic pressure sufficient to burst the tube along the longitudinal element.

The aim is to approach the ultimate mechanical efficiency possible, and at the same time to keep actual production in mind.…

Summarizing the aims of this investigation, it can be said that the objectives of this investigation are:

1. To design ends for closed vessels.
2. To form the designs.
3. To …

Photoelastic Investigation Of The Stresses In A Capless Connecting Rod, Gerald Delaine Smith

Masters Theses

"For a great many years the primary method used to solve engineering problems was by the use of mathematics. However, rigorous and simple mathematical solutions are only possible if the geometry of the member and its loadings are relatively simple. When irregular shapes with complex loadings are encountered, rigorous mathematical solutions for stresses induced are either impossible or very cumbersome. In such cases, the engineer must resort to other methods which are available today.

This paper attempts to show the application of the photoelastic method to such a problem. Moreover, it will show the comparative ease with which the designer …

Effect Of Viscosity On The Cetane Number Of A Diesel Fuel, Moris Bolay

Masters Theses

"The object of this paper is to determine or rather experimentally establish the effect of a change in viscosity of a given diesel oil in regard to the ignition quality (cetane rating) of the oil.

The author did not attempt to prove why or find out how much the cetane number was affected. But, merely, tried to experimentally verify the fact that the cetane number of the fuel used underwent a change when its viscosity was decreased by preheating it.

Since his professional interests lie in the field of automotive engineering, several thesis problems were suggested to him by Dr. …

The Holding Strength Of Crimps On Tubes, Aydin Cansever

Masters Theses

"The object of this thesis is to determine by analytical means and laboratory tests the holding force of various crimp methods of fastening sheet metals and special tubing. The study is conducted with heat treated Aluminum alloy 24S.T3.

The problem of joining relatively thin walled tubing of high strength material or the application of a plug to such a tube has been investigated by many manufacturers, but the literature in this field is limited and still there are many cases where a better method may prove very useful. At the suggestion of Dr. Aaron J. Miles, the author decided to …

The Effect Of Various Binders And Moisture Content On The Apparent Thermal Conductivity Of Green Foundry Sand, Robert V. Wolf

Masters Theses

"The broad field of heat transfer is well developed in its theory and mathematics, however, some few applications of varying heat transfer rates have been explored only recently.

Previous to the nineteen-thirties, foundrymen had apparently been interested in heat transfer measurements only from the standpoint of the melting of metals and the heat treatment of the finished castings, with the rate of solidification and the transfer of heat from the casting through the mold being ignored, or at least accepted as an uncontrollable factor. This does not apply, of course, to the use of metal chills to adjust solidification rates …

Photoelastic Investigation Of Notched Corners In Square Apertures In Flat Plates Subjected To Tension, Lloyd E. Byrd Jr.

Masters Theses

"Photoelastic stress analysis is one of the most effective methods available to the engineer for solving problems of stress distribution. The effect of forces, such as pressure and tension may be studied using a scale model of a structural part. Special transparent models are subjected to forces proportional to those acting on the real object. The stress problem produced in the model indicates the stress distribution through a cross-section of the structural part.

Analysis of the photographic record of the stress analysis pattern provides data with a high degree of accuracy within a relatively short time. In simple cases, this …

Air Flow Through Cloth Screening, Kurt Rauf Basakinci

Masters Theses

"The object of this investigation is to obtain an expression whereby flow of air through woven cloth can be predicted with a reasonable degree of accuracy, in terms of the pressure drop across the screen, the density, the viscosity of the air flowing; these latter properties being functions of the pressure and temperature of the air.

The development of an expression from which to predict the relationship between the air flow through a screen and the pressure drop across it without resort to experimental procedure seems to the author to be worthwhile undertaking.

The chief aim of this investigation was …

The Effect Of Back Pressure Created By A Venturi Tube On Power Output And Efficiency Of An Internal Combustion Engine, James J. Trace

Masters Theses

"The exhaust pressure against which an engine works affects the amount of pumping losses, the volumetric efficiency and the rate of advance of the flame front during the combustion process.

When the back pressure is decreased to the same pressure as the intake pressure, the amount of negative work done during the exhaust-intake process approaches the positive work done during the process. It can be seen from a PV diagram that it is possible to make this negative work less than the positive work and gain work during the process.

Because of the "15 to 30 degrees” of intake valve …

Highway Construction And Maintenance Equipment With Machine And Automotive Repair Shops For The Reconstruction Of The Highways Of The Iv Division, Ankara, Turkey, Steve Theodorides

Masters Theses

"With the rapid advancements being made in travel and communication facilities today, the world is steadily growing smaller and people in the far places of the world are no longer strangers.

There is no doubting the importance of tractors, dozers, scrapers, power shovels, graders, bituminus construction equipment, aggregate handling, etc., in the present-day world, in aiding the progress of civilization and bringing to all people the good things of life.

It must be remembered that money expended for highways is not wasted, and can be classified as an asset.

In substance, this is a general project for the reconstruction and …

The Effect Of A Uniform Layer Of Insulation On The Temperature Amplitude In Periodic Heat Flow, Ralph E. Schowalter

Masters Theses

"The object of this thesis is to determine by analytical methods the temperature at any time within a homogeneous semi-infinite solid protected by a uniform layer of insulation, while its one and only one plane face is subjected to a periodically fluctuating temperature. The temperature at an infinite distance within the solid is to remain constant, and the heat flow in the other two directions is to be considered negligible.

Periodically fluctuating temperatures are frequent in both nature and engineering. The surface of the earth is subjected to temperature changes which are very nearly periodic, and these changes are made …