Mechanical Engineering Commons^™

Prove Primary Battery Structure, John D. Burkhart, Andy Mccormick, Ryan Yu, Soren Barclay

Mechanical Engineering

In conjunction with Prototype Vehicle (PROVE) Laboratory, our group designed, manufactured, and tested a prototype structure to house the battery boxes for PROVE’s endurance vehicle. Our structure was designed to support the batteries during normal use, and in the event of a front crash. Our design is comprised of a secondary composite box to house the battery boxes, a bottom plate to affix the secondary box to the chassis floor, a horizontal plate fastened to the chassis, and a brace structure welded to the chassis. From the outset, we chose to use a secondary box, the primary battery boxes must …

Rapid Composter, Shannon Shinozaki, Avin Atencio, Jonathan Fraser, Lukas Kolbl, Russell Occhipinti

Mechanical Engineering

This project was created with the intent of automatically composting equine bio waste to be reused as plant fertilizer. The system consists of four subsystems: power generation and storage, automatic controls, aeration, and structure. Each subsystem may be manufactured independently, then put together. This system will not have access to power outlets, so it was designed to be solar-powered.

Parametric Bicycle Yoke, Colin Reay, Walter Minehart, Robby Harrigan, Jordan Olson

Mechanical Engineering

This report outlines the entire design, fabrication, and validation process of a parametric yoke design that addresses the packaging problem of the bottom-bracket chainstay junction in modern bicycle frames. The goal was to create an elegant, space-efficient solution that is accessible to the Cal Poly Bike Builders Club. The report includes documentation of the three-part fixture system, manufacturing process, and testing results for the yoke.

Our yoke design outperforms traditional round-tube weldments in torsional and vertical stiffness. Additionally, all manufacturing fixtures and machining operations function as intended, resulting in a finished yoke that meets all required tolerances in under an …

Treadmill Platform For Quadrupedal Robots, Baxter J. Bartlett, Jack F. Butler, Phillip A. Shafik, Tarun S. Ganamur

Mechanical Engineering

Cal Poly Legged Robots, led by Professor Refvem and Professor Xing, has been leading Cal Poly’s attempts to simulate, produce, and test their legged robots. The initial testing of the locomotion of these robots can be dangerous to the robot since any bugs in the code could cause the robot to fall over and harm itself. Our responsibility as a team was to deliver a portable platform for testing the locomotion capabilities containing a fall prevention mechanism. In short, we have designed a platform for this purpose that consists of a treadmill surrounded by a wheeled chassis with a system …

Perforated Groove Cam Lock, Matthew J. Redmond, Samuel A. Potter, Dylan Weiglein, Andrew Reese

Mechanical Engineering

NASA Artemis III astronauts need a way to attach and detach various tools to an extension handle to be used during lunar EVA sample collection. Because lunar dust is so harsh and abundant, mechanisms must be designed to function regardless of the number of contact particulates. Past designs used on the Apollo missions proved to be problematic for their operators, opening the door for innovative improvement. A new mechanism has been proposed that directly addresses the performance issues of the original handle extension mentioned in NASA’s Apollo mission reports. The new mechanism boasts an open design that promotes dust tolerance …

3d Printed Aircraft, Matthew Nagy, Charles D'Amico, Alexis Salgado Medina

Mechanical Engineering

This project is to design, build, and test a 3D-printable aircraft. The goal is to create a final design that will be able to fly for the longest duration possible, around 20 seconds. To determine the correct preliminary design and manufacturing process for a 3D printed RC aircraft, an analysis of multiple design options and manufacturing materials was performed. This allowed for a variety of choices for aircraft type, airfoil design, structure, among other topics to be narrowed down to the most promising option. It has been found that the aircraft will follow a design similar to industry motor-gliders, with …

Backflow Relief Valve Test Stand, Olivia Mcnulty, Wiill Halvorsen, Ryan Dubois, David Leaman

Mechanical Engineering

This Final Design Review (FDR) document details the final design, manufacturing, testing, and results of the Zurn Wilkins Backflow Relief Valve Test Stand Project under the sponsorship of Brian Yale and Rueben Westmoreland. This project involves simulating real-world conditions of static pressure and water hammer cycling. The stand will give Zurn Wilkins’ engineers a method by which to test their relief valves prior to a rigorous, yearlong University of Southern California (USC) testing procedure. Our design involves using city water, a pump, a Zurn backflow preventer, and a control system to apply specific pressures to each end of the relief …

Saver: Surface Autonomous Vehicle For Emergency Rescue, Lucas Je Sandsor, Michelangelo Coltelli, Brian Wong, Sebastion Rivero, Kobe Hayashi

Mechanical Engineering

The design, fabrication, and testing of an unmanned surface vehicle for the NASA Micro-G NExT SAVER challenge. This device features a radio direction finding phase array to autonomously navigate to an emergency distress beacon to deliver emergency supplies.

Programmable Vibration Table Retrofit With Eagle Medical, Jonathan Ilagan, Madhav Asok, Max Lewter

Biomedical Engineering

This project aimed to repair and upgrade a vibration table used for package testing for the sponsor, Eagle Medical - a medical packaging and sterilization company based in Paso Robles, California. The current vibration table is not programmable and lacks circuit diagrams, making it difficult to repair. In addition, it is not functional due to internal circuitry issues and power requirements. To address these issues, the team will implement several upgrades to improve the product and allow for better random cyclic vibration testing. A full assessment of the existing vibration table will be conducted to ensure the viability of these …

Statistical Uncertainty Of The Ignition Time, Burning Rate, And Extinction Characteristics Of Engineered Timber Products, Jacob David

Master's Theses

The characterization of flammability parameters such as time to ignition, mass loss rate (MLR), and extinction criteria is critical for understanding ignition and burning behavior of timber products. These parameters, often determined with bench scale experiments, have previously been presented in literature. However, standard test methods generally use relatively low trial quantities (e.g., n=3) which can potentially cause large variation in reported values. This study investigates the influence of trial quantity on observed statistical variation in key flammability metrics for timber products (e.g., ignition time, peak MLR, MLR at extinction). Using a conical heater, 100 repeat trials were conducted …

Development Of A Low-Cost Acoustic Gauge For Simultaneous Tide And Wave Measurement, Alexander Kalman Dunn

Master's Theses

High-quality tide and wave data are essential in a variety of fields including coastal engineering, climate science, disaster response, and recreational activities. Accurate data are publicly accessible from government organizations such as the National Oceanic and Atmospheric Administration (NOAA), however the high costs associated with deploying and maintaining their high accuracy gauges results in a deficit of localized data. Commercial gauges available starting at $2,000 are still expensive for local agencies and individual users to deploy and maintain. These commercial options can also be limited in their scope, accuracy, or ease of use. In this thesis, a low-cost acoustic gauge …

Development Of Mirror Flexures For Use In The Muvi Instrument, Colin W. Harrop

Master's Theses

The Miniaturized Ultraviolet Imager (MUVI), is a compact wide field UV imaging instrument in development at UC Berkeley Space Sciences Laboratory and Cal Poly, San Luis Obispo. MUVI is designed to fit in a 2U CubeSat form factor and provide wide field, high resolution images of the ionosphere at far ultraviolet wavelengths. This thesis details the design and analyses of MUVI’s deployable cover mirror mounting flexures. Three different flexure geometries were evaluated, an optimal candidate was determined based on a number of criteria including isolation of vibration and stress to the mirrors, manufacturability and cost. The design of the flexure …

Portable Drinking Water Cooler And Dispenser, Gustavo Hernandez-Lerena, Erik Torres, Caleb Francis Parham, Terry Leung

Mechanical Engineering

This document serves as the comprehensive report for the testing and building for the Portable Water-Cooling System by team AquaCool. Team AquaCool is comprised of four mechanical engineers with a passion to help the agricultural industry in their efforts to keep the health of the workers at their peak. The four engineers who partook in helping the farm workers are as follows: Caleb F. Parham, Erik Torres, Gustavo Hernandez-Lerena, and Terry Leung. To reduce the risk of heatstroke and other unwanted effects from the harsh working conditions during summer, a small and portable system was built to help in the …

Reflect To Connect, Sophia Rae Guzules

Liberal Arts and Engineering Studies

Engineering statics is an important course and a prerequisite for many subsequent courses for many engineering majors. It is often students’ first exposure to technical engineering sciences. Most statics concepts are addressed in ways disconnected from students’ prior experiences and interests. Utility Value Interventions (UVIs) have been employed in fields like biology and chemistry to help students connect concepts in class and their lives outside the classroom. However, UVI usage in engineering so far has been limited. In this Senior Project paper, I will describe the process that the team Critical Research in Engineering and Technology Education (CREATE) and I …

Ultrasonic Mapping Needle, Katie R. Stone, Stu Bembenek

Mechanical Engineering

When gaining access to a vein or organ for the purpose of ablation or other reasons, the common procedural method of entry is to use the Seldinger technique. This has been the standard entry procedure since its introduction in 1953, and the technique has not been modified during this time. While effective, it is prone to complication as it relies solely on the operator's precision and experience. It is our task and goal to develop a modifying kit for this procedure that would aid the operator in this process. It would make use of mapping technology and standard products used …

Trajectory-Tracking Control Of The Ball-And-Plate System, Dominic E. Riccoboni

Master's Theses

The Mechatronics group in the Mechanical Engineering department of Cal Poly is interested in creating a demonstration of a ball-and-plate trajectory tracking controller on hardware. The display piece will serve to inspire engineering students to pursue Mechatronics and control theory as an area of study. The ball-and-plate system is open-loop unstable, underactuated, and has complicated, nonlinear equations of motion. These features present substantial challenges for control - especially if the objective is trajectory tracking. Because the system is underactuated, common nonlinear trajectory tracking control techniques are ineffective. This thesis lays out a theoretical foundation for controlling the hardware.

Several important …

Mechanical Metamaterials, Brent A. Peluso, Oliver T. Parker

Mechanical Engineering

Mechanical metamaterials are an emerging design strategy aimed at tailoring lattice structures to achieve specific properties such as negative Poisson’s ratios and guiding wave propagation. These metamaterials have received increasing attention from various application domains, including medical devices, aerospace, automobile, and infrastructure. The scope of this project is to vary a single lattice parameter and quantify its effect on the structural properties of the given 3D lattice.

Planar Element Alignment System, Benjamin E. Lavigna, Benny F. Cruz, Samuel Gierhan, Jacob Q. Henriksen

Mechanical Engineering

Precise alignment to the micron level is a necessity for microfluidic/micromechanical devices to function as designed. Because of this, a micro-alignment device was commissioned by Professor Hans Mayer on behalf of the Cal Poly Microfluidics Laboratory. Prototype creation was bounded by a set of requirements including, ability to align PDMS & Silicon wafer halves to ± 10 microns, total process speed of three minutes, and total budget of $3000. Some major design hurdles included an ability to verify alignment, possible non-planar alignment pieces, and an inability to contact any point on the face of the alignment pieces after bonding treatment. …

Northrop Grumman Collaboration Project, Nikkia Rae Psomas-Sheridan, Santiago Robles, Ben Elkayam, Benjamin Ulfhake

Mechanical Engineering

The Northrop Grumman Collaboration Project (NGCP) is a collaborative club project sponsored by Northrop Grumman for the students of Cal Poly San Luis Obispo (CPSLO) and Cal Poly Pomona (CPP) to create a fleet of vehicles to aid in the simulated rescue of stranded hiker. The CPSLO club is responsible for delivering an autonomous flight vehicle that can suppress a fire and retrieve a payload. Mechanical Design Team of the CPSLO team was responsible for the design of the frame, electronics housing, and payload and fire suppression systems.

Design Of A System To Investigate The Relationship Between Feedback And Delivery Medium For A Novel Motor Task, Ashley Humpal

Master's Theses

Stroke is a chronic, lifelong illness, and full recovery requires continuous physical and cognitive rehabilitation. Such long-term rehabilitation is cost-prohibitive; however an approach to providing long-term therapy that has recently gained traction is the use of socially assistive agent (SAA) systems. These systems make use of non-contact communication devices and can be used to guide people through a variety of rehabilitative tasks. They have the potential supplement current rehabilitation practices by providing motivation during intense exercises, and can extend the reach of the therapist into remote and home settings.

Though SAA systems have been used in a variety of rehabilitative …

Use Of Precious Plastic Method Of Bricks For The Construction Of Tiny Homes, Haylie E. Tallon

Architectural Engineering

Precious Plastics, a Netherlands based company, created an open source project that can be used to create different objects from recycled plastics. The San Luis Obispo area has a large amount of recyclable plastic that is being treated as trash, adding to the pollution of the ocean and the air. This project is to determine the necessary steps to create plastic building blocks, using the Precious Plastic process, as a construction material for low-income, temporary housing. This report covers the process that was used to build two of the machines that will be used to create the bricks. This requires …

Callaway Measurement Device, Andre S. Fisher, Roman Hays, Blake Sousa, Grant Gabrielson

Mechanical Engineering

The purpose of this document is to illustrate the Callaway Measurement Device senior project from start to finish. The challenge given to the team was to update and improve a gauge used by Callaway employees to measure the loft, lie, and face angle of their full spectrum of golf clubs. Once the team understood how the pre-existing gauge operates, the team conducted background research into other technologies that could improve the gauge. The team decided to digitalize the device amongst other tweaks to reduce error. Because the CAD files were not available for the pre-existing device, the team began reverse …

Gasifier Wall Wash Manifold, Ashley Sieu Che, Gintaras Julius Baipsys, Peyton Joseph Archibald, Michael Thomas Kieran

Mechanical Engineering

The objective of our Gasifier Wall Wash Manifold Project is to design three different manifolds that will uniformly distribute water on the inner diameter of a pressure vessel. Also, the distributed water should completely cover the circumference of the inner walls. From extensive research of current solutions as well as the conduction of technical analyses, we were able to produce three designs that would be able to meet our engineering specifications. Time constraints led to the fabrication of one manifold design along with a test rig. With a fully functional test rig, we saw positive results from our design verification …

Locking Solar Tracking Bushing, Benjamin James Reed, Andrew Donald Maas, Angel Navarro-Iniguez, John Vincent Bruner

Mechanical Engineering

The contents of this final design review (FDR) outline the progress made by a team of four mechanical engineering students at California Polytechnic State University, San Luis Obispo to solve the problem of torsional galloping in solar tracker panels since the preliminary design review. The project proposed by the sponsor, Christian Friedrich, on behalf of ARaymond is a design for a friction based braking system integrated into a redesigned bushing.

The CDR contains details about the system design, the design justification, the manufacturing plan, and design verification plan. In the system design section, the four manufacturing subsystems (bushing mount, actuation, …

Novel Hitch Cargo Cart, Cesilio Sanchez Ramirez, Lance Haidet, Richard Lontoc, Tyler Selinka

Mechanical Engineering

This document presents the engineering design process used to develop, manufacture, and test a new and improved iteration of a hitch cart prototype. This process was performed by a team of four mechanical engineering seniors as part of California Polytechnic State University, San Luis Obispo’s senior design pathway. The goal of this project was to develop a sturdy and reliable iteration of our sponsor’s hitch cart prototype, that integrated the functionality of a vehicle hitch cargo platform and that of a height adjustable cargo cart into a single streamlined and easy to use product. This design could be used by …

Tree Climbing Limb Saw, Andrew E. Bray, Parker Tenney, Drew M. Robles, Aimee T. Chiem

Mechanical Engineering

This document is the comprehensive report for the Tree Climbing Limb Saw Senior Project. The purpose of the Tree Climbing Limb Saw project, completed by mechanical engineers Andrew Bray, Aimee Chiem, Drew Robles, and Parker Tenney, is to remove low-hanging branches (<15 >ft) to prevent forest fires from travelling up into the canopy, where wind can carry embers for miles. An RC car was heavily modified to create a solution for this problem. A chainsaw was also mounted to deal with the cutting part of the problem. Creating a project which aims to solve this problem is a great step …

Novelty Ice Cream Assembly Prototype, Mason Sylvester, Logan Williamson, Alvaro Martinez, Adin Gilman-Cohen

Mechanical Engineering

Cool Beans USA is a novelty ice cream startup company founded by Keith Zachow. In the winter of 2022, our team began working with Mr. Zachow to develop a machine to automate parts of the production process for his product. This product consists of two hemispherical ice-cream cone shell halves filled with soft serve ice cream and pressed together. The assembled pods are around the size and shape of a small walnut and are intended to be sold in stores as a frozen finger food. At the time of project inception, this product was in its early stages and was …

Rotating Backing Brush, Caleb Savard, David Dalal, Max Allred, Mathis Weyrich

Mechanical Engineering

In the final steps of GAF’s shingle production process, small asphalt particles called fines are applied. Some fines adhere well to the shingle sheet, while others temporarily stick only to fall off the sheet further down the manufacturing line. As a result, the shingle plant floor is covered in fines that have fallen due to vibrations and gravity. The technicians and engineers at GAF want a cleaner working environment and to potentially reuse the loose fines. We are a senior project team that solved this problem by designing a system to remove and collect loose fines. In this document, the …

Baby Soothing Device, Grace Kalene Mekrut, Matteo Gozzini, Miles Angel Ibarra, Christian Joel Roberts

Mechanical Engineering

This document is the official final design review for the Baby Soothing Device. This product is intended to help families sleep throughout the night by allowing a baby to be soothed back to sleep without constant and direct parental interaction. It is maintained by Mechanical Engineering students at California Polytechnic State University, San Luis Obispo for Dustin Yoder, the project sponsor. The purpose of this document is to present the design process from ideation to finished design in great enough detail that its manufacturing procedure may be replicated if desired. This document further explains all the research, testing, and benchmarks …

Hypoxic Incubation Chamber, Simone Lisette Helfrich, Makenzie Nicole Jones

Biomedical Engineering: Graduate Reports and Projects

This paper describes the design, manufacturing, and testing of a novel controllable hypoxic incubator with fully functional oxygen gas control and temperature control in a humid environment. On the current market, a majority of the few hypoxic incubators use pre-mixed gas that does not offer precise control over gas concentration. The objective for this project was to create a chamber that allows the user to set the O2 concentration to varying set points of % O2 while maintaining the chamber at a constant body temperature, CO2 level, humidity, and sterility. To start the project, multiple concepts were developed for the …