Mechanical Engineering Commons^™

Hydropower Collegiate Competition, Aiden D. Foster, Devon Bountry, Joanna Vo, Timothy Rinker, Amanda Rodriguez, Minh Nguyen, Eli Haushalter, Sophie Watkinson, Maiya Holton, Breanne Evans

Mechanical Engineering

The Cal Poly SLO HCC team presents a feasibility study and engineering design review package for retrofitting the non-powered Ritschard Dam in Colorado into a hydroelectric facility as part of the 2025 Hydropower Collegiate Competition. Through a rigorous and multi-staged assessment of plausible dam sites in the western US, the team has chosen the Ritschard Dam in Colorado to implement an electromechanical component designed to accommodate a large range of flowrates stemming from a large variance in upper reservoir capacity due to geographical and climate effects. The team evaluated non-powered dams based on technical feasibility, electric grid proximity, power generation …

Automation Of Post Fermentation Must Removal, Grace Hurley, Jakob Spink, Ariel Metscher

Industrial and Manufacturing Engineering

The Harvest Haulers project addresses a critical operational inefficiency at Saucelito Canyon Winery, where post-fermentation must removal from wine barrels was labor-intensive and potentially hazardous. This project aimed to develop a custom forklift attachment that could securely handle Bordeaux and Burgundy barrels, streamline the dumping process, and improve worker safety.

The resulting solution is a forklift-compatible fixture designed to lift, secure, and tilt barrels using a robust combination of a modified aluminum pallet, padded hoop, ratchet straps, and a custom hinge mechanism. The design meets all engineering requirements, including a 600 lb. load capacity, 135° tilt, and a single-operator setup …

Multimodal Self-Folding Of Shape Memory Polymer Using Laser Induced Graphene, Liam Harrison Drew

Master's Theses

Shape memory polymers (SMPs) can undergo programmed shape transformations when heated above their glass transition temperature (T_g), enabling actuation through stimuli such as infrared (IR) radiation and Joule heating. These materials are promising for deployable systems and soft robotics due to their lightweight structure and elimination of traditional mechanical components. While IR-based actuation is simple and low-cost, it lacks precision in uncontrolled environments. Joule heating offers improved control but is often limited by conductive ink properties such as thickness, stiffness, or poor adhesion. This work introduces a novel method for multimodal SMP actuation using laser-induced graphene (LIG) transferred …

Effect Of Manufacturing And Machining Process On Recycled Composite Connecting Rods Under Tension And Compression, Walter W. Oppelt

Master's Theses

Carbon fiber reinforced polymer (CFRP) is an engineering material renowned for its high-strength and low-density material properties. Such properties make CFRPs especially useful for applications across many industries, including aerospace, automotive, marine, sporting goods, oil and gas, and more. However, with such favorable material properties comes the cost of high energy usage required to produce raw carbon fiber. Recycled carbon fiber (rCF) has emerged as a promising alternative, offering a significant reduction in energy usage. This research explores the viability of applying recycled CFRPs to internal combustion engines to both reduce energy costs during manufacturing and while in use. Mechanical …

Cryogenic Fuel Delivery System, Carter Josef, Reilly Humphreys, Joseph O'Connor, Nick Spreen

Mechanical Engineering

This project presents the design and validation of a cryogenic fuel delivery system aimed at enabling sustainable aviation through hydrogen fuel vaporization. Developed by a team of senior mechanical engineering students at Cal Poly and sponsored by Boeing, the system utilizes atmospheric air to vaporize liquid nitrogen, used as a stand-in for hydrogen, via forced convection heat exchangers, eliminating the need for engine-supplied heat and reducing parasitic loads. A feedback loop and turbine component are integrated to regulate pressure and recover energy, respectively. A benchtop prototype was built and tested to evaluate system performance, with results closely aligning with analytical …

Conversational Social Robot, Julianna M. Christopoulos, Mackenzie Goldman, Cece E. Hujanen, Jared Hunter

Mechanical Engineering

Background: Social robots are used in various settings to reduce burden on human workers and expand opportunities for people in need of assistance.

Challenge: Design a humanoid robot head and torso capable of holding conversations and interacting with a user using a LLM and motion. Conversations are limited to discussing Cal Poly resources and opportunities with visitors to the Bently Research Center on campus.

Scitechatorium, Olivia Lafferty, Yvonne Brien Miller, Colton Swinth, Savannah Pinheiro, Gage Heinze

Mechanical Engineering

Bellevue Santa-Fe Charter School (Bellevue) is a K6th grade public charter elementary school in Avila Beach, California. The primary focus at Bellevue is fostering unique learning experiences, empowering students through project-based learning, and engaging students in creative endeavors. Following these themes, the school has allocated space and funding for an on-campus science and technology museum known as the SciTechatorium. The museum is currently open during students’ lunch period, providing interactive displays on concepts in human biology, nature and wildlife, physics, and electronics. Bellevue’s K-6th grade science teacher, Christian Strauli, and Bellevue parent volunteers are primarily responsible for the museum’s upkeep …

Evoque Delivery System Fixture Optimization, Jack Ellis, Florence Duff, Noah Dunsmore, Timothy Hunter, Rafael Castillo

Mechanical Engineering

No abstract provided.

3d Printed Fixed Wing Aircraft Competition, Sidney E. Long, Mitchell Heise, Jack Bride, Daniel Salinas

Mechanical Engineering

Cal State LA and Arlington University, Texas are hosting the same 3D printed, fixed wing aircraft competition for 2025. Cal Poly requires a competitive plane that can adhere to each rule and be piloted remotely to achieve the longest time in the air. The plane must utilize solely 3D printing technology for the wings, body, and all other structures. The only off-the-shelf components can be the motor and electronics, as well as mechanical devices such as hinges.

Combustion Liner Optimization, William Weeks, Daniel Reed, Isaac Trull

Mechanical Engineering

Solar Turbines provides gas power generation solutions, focusing on gas turbine engines and compressors. The Gas Turbine Products Engineering (GTPE) team at Solar Turbines needs a way to efficiently and cost-effectively maintain the combustion liner of the Taurus model gas turbine at or below the cold-side temperature target. The current system involves a manufacturing process with ergonomic concerns and uncertain cooling effectiveness.

To address this, our team proposed a new combustion liner system featuring impingement cooling. We provided Solar Turbines with heat transfer models of both the existing and proposed designs, demonstrating improved cooling performance. Additionally, a prototype of the …

License To Drill, Gabrielle Noemi Orlando, Alexcias Olga Meeks, Dayana Guadalupe Gonzalez, Mark Dahmen

Mechanical Engineering

The goal of this project is to provide the student machine shops with an updated License to Drill (LTD) certification training, formally known as the Red Tag. The current training has two key components: a preliminary Canvas course and an in-person training with a safety tour, safety quiz, and a hands-on project. Currently, the hands-on project is outdated and unengaging. Thus, the primary focus is to replace it with an inspiring and memorable project, which includes written and visual instructional content on how to make it. The Canvas will thus be updated, a new instructional video will be created, and …

Pendulum Wave Generator, Abigail Jocelyn Romero, Paul Staley, Wendy Dong, Kyle Schumacher

Mechanical Engineering

The Cal Poly Mechanical Vibrations Laboratory (Vibes Lab) serves to educate and excite students about mechanical vibrations through hands-on experiments. While the lab contains several relatively complicated technical experiments, it lacks simple demonstrations with immediate visual interest to appeal to audiences with less technical backgrounds. Because of this, faculty desired a fun and interactive demonstration project that could be operated with no prior training. The project chosen for this is a Pendulum Wave Generator which is a set of multiple pendulums with differing lengths that combine to create complex and observable patterns over time. This project was completed by a …

Adaptive Riding Mount Block, Lucas R. Reynolds, Lukas M. Moreau, Patrick J. Michael, Jandre D. Lafradez

Mechanical Engineering

Professor Sarah Stewart from the Animal Science Department at Cal Poly seeks to develop a solution to help people with disabilities mount horses. Users need a mounting block that can bring them closer to the horse’s back to ease mounting. The current system, consisting of two plastic two-step blocks, is inadequate—unstable, too small, and inaccessible for wheelchair users.

The required solution must meet several key specifications: it should accommodate at least three people standing side by side, be sturdy enough to support their combined weight, and remain stable on rugged terrain like gravel or sand without tilting or sinking. Additionally, …

Lidss Raft Battery Pack Integration, Jack Maxwell, Vincent Stevens, Matthew Hoodmaker, Colin Flanders

Mechanical Engineering

Lawrence Livermore National Laboratory is a critical member of the United States Department of Defense. Their Independent Diagnostics Scoring System (LIDSS) uses rafts that operate in the ocean to collect missile test data. Several times a year, the United States will test their Inter-Continental Ballistic Missiles by launching them into the ocean near the Marshall Islands. This is where the LIDSS rafts collect their test data. Our project was centered around re-designing the battery pack used by the rafts. The current battery pack design experiences water ingress problems and is difficult to access. Our re-designed battery pack is waterproof to …

Thermal Modeling Techniques For Additively Manufactured Porous Metals, Lucas D. Rambo

Master's Theses

Advances in additive manufacturing have enabled the creation of metallic components with tailored porosity, offering design flexibility for thermal, structural, and fluid transport applications. This thesis investigates the effective thermal conductivity (ETC) of porous Inconel 625 (IN625) and Inconel-ceramic composites (IN625-RAM2) fabricated by Laser Powder Bed Fusion (LPBF) using Elementum 3D’s PermiAM technology. Experimental measurements of thermal conductivity using the laser flash method are compared to numerical models built from micro-computed tomography data. Simulations were performed using both finite element (FE) and finite volume (FV) methods to evaluate thermal transport in real microstructures. The study investigates the effects of micro- …

Comparative Study Of Experimental And Fea Strain Data For Cnt-Coated Fiberglass Sensors, Extensometers, And Metal Foil Strain Gauges, Omar Dwidar

Master's Theses

Material testing is essential across industries such as aerospace, automotive, and construction, playing a critical role in verifying material selection, diagnosing failures, and understanding the development of flaws in structures. These insights are key to designing successful, reliable systems. Conventional metal foil strain gauges are low cost and reliable but provide limited sensitivity with a typical gauge factor around 2. Extensometers provide highly sensitive strain measurements with the disadvantage of a bulky form factor. With advanced materials such as carbon nanotubes, it is possible to manufacture a sensor with the sensitivity closer to that of an extensometer with the small …

Design, Fabrication, And Testing Of A Dual-Rate Spring System For Mountain Bike Frames, Lucas P. Grizzle

Master's Theses

The design of full-suspension mountain bikes is a careful balance of suspension kinematics, structural dynamics, and manufacturing optimization for the expected use case. A bike designed to excel in one area will likely exhibit reduced performance in others. This optimization problem is addressed by designing, integrating, and testing a dual-rate spring system within a fully custom frame. The dual-rate spring is fully decoupled from the rest of the suspension kinematics, providing designers with an additional parameter to achieve ideal suspension behavior. This is accomplished by placing a thermoplastic polyurethane (TPU) bushing in series with the rear shock. The influence of …

Model-Based Design Of Compressed Lithium-Metal Pouch Cell Battery Modules For Evtol Applications, Scott J. Stirling

Master's Theses

Batteries with higher specific energy and power are essential for extending the range and performance of electric vertical takeoff and landing aircraft (eVTOLs). Anode-free lithium-metal pouch cells offer strong potential at the cell-level but require high compressive pressures to enhance cycle life and discharge performance. These pressures necessitate heavier structural components, reducing packaging efficiency at the module level.

To evaluate this tradeoff, a full-factorial enumeration model was developed to explore viable module designs within a constrained packaging volume. The model scales subsystem masses, enforces design rules and material limits, and accounts for large (~20%) cell thickness changes during cycling.

Results …

Hands-Free Balance Protocol And Development Of An Iphone App For Self-Assessment, Jacob Matties

Master's Theses

For many clinical populations, the measurement of balance is a critical task. Previous studies have agreed that smartphone IMUs provide a valid measure of balance that can be significantly correlated with force plate measurements and is sensitive enough to distinguish between various balance poses, but many balance assessment protocols require uncommon equipment or the use of hands during assessment. These limit accessibility of balance assessment. To eliminate the need for hands or any additional equipment, this study assessed the use of a smartphone recording the root mean square of 3D acceleration magnitude. The goal of the study was to determine …

Adjustable Dynamometer Motor Mount, Garrett Carson Ng, Elijah Siegel Reuven, Ethan Fong, Daniel Larimer

Mechanical Engineering

The Cal Poly Electrical Engineering Department and sponsor Dr. Dolan needs a manufacturable motor fixture that securely aligns motors of various sizes with dynamometers. Previous lab motor fixtures could not accommodate motors of different sizes, making precise alignment between motors and dynamometers time-consuming and unreliable. Our team developed a modular, manufacturable fixture capable of aligning various motor sizes quickly, accurately, and securely, enhancing lab consistency and usability.

Baja Sae Brakes, Carson Moore, Jaedyn Michael Imhoff, Will Duncan, Matthew Shaffer

Mechanical Engineering

Historically, the Cal Poly Racing Baja SAE has produced a braking system that has proven unreliable and barely passes competition rules and inspections, leading to ill performing and unsafe brakes. The goal of this project is to produce a system and documentation that meets the requirements provided by Cal Poly Racing Baja SAE. The final design includes a transient braking model of the vehicle to set system requirements, universal custom front and rear calipers modified from “Cal Poly BSAE Custom Brake Caliper Senior Project”, and a revamped hydraulic harness. Leaning on the team’s previous work and modifying the custom calipers …

Cruising On The Beach (Cob), Juan Diego Molina Ii, Ashley Kianna Burga

Biomedical Engineering

This report details the design and development process of Cruising on the Beach (COB), a modular motorized wheelchair intended to improve beach accessibility for high school students with mobility impairments. The project aimed to create an affordable, portable, and sand-capable device using balloon wheels, an adjustable control panel, and a customizable base. Extensive background research, market analysis, design modeling, and test plans were completed. However, final fabrication was not achieved due to financial constraints and limited access to industrial machining tools needed for custom metal components. Despite these setbacks, the project delivered a robust conceptual design and a fully …

Helical Products Parts Display Stand, Binh Nguyen, Emily Yuan Mendyke, Zoe Porter

Mechanical Engineering

Helical Products needs a new product display stand that will demonstrate their custom springs, couplings, and u-joints. Their current display stand, a marble run contraption, is large, loud, and difficult to transport, so they would like the new stand to remedy these issues. The goal of this senior project is to create a display stand that captures the attention of their customers with dynamic product demonstrations while addressing the issues outlined above.

The new display stand is also a marble run contraption, but instead of being almost 4 feet tall and 3 feet long, it is 23” tall, 26.25” long, …

Vanlife Desalination, Emily Rhee, Tomas Franco, Marco Jimenez

Mechanical Engineering

Van life can be defined as the unconventional lifestyle of living in a car, van, or motor vehicle. Living in a motor vehicle allows for you to effectively live in whatever location you deem fit, and with that comes certain standards that need to be met; one being fresh potable water used for drinking, hygiene, and basic living. The scope of this project is to design a system that can effectively remove salt from seawater (desalinate) and can be integrated into a van that can be used for off-grid living.

In this project we worked to create a design that …

Development Of Planetary Drive System For Formula Sae Electric Race Car, Brian Wong, Bradley Maruoka, Joshua Charles Fine, Madison Kai

Mechanical Engineering

Hub motors are compact electric motors mounted directly on each outboard wheel hub. Utilized in Formula SAE and Formula Student vehicles, this configuration offers several advantages over traditional drivetrains, including packaging optimization within the chassis, vehicle traction, and improved efficiency. Although hub motors are not yet common in 4WD vehicles, they are being explored for use in EVs and may become more common in the future. Every year, Cal Poly Racing FSAE designs and builds a formula-style race car. To improve drivetrain performance, the team is investigating the achievability of a hub motor 4WD drivetrain, requiring extensive research, development, and …

Wind Turbine Rotor Test Stand, Ashlen Brooke Sperry, Cayley Mckee, Kristofer Lee Pascua, Francisco Medina

Mechanical Engineering

Dr. Lemieux and the mechanical engineering department at Cal Poly are renowned for the countless projects that allow students to be a part of hands-on learning and the “Learn by Doing” experience. One such experience is the wind energy class that requires students to design, build, and test wind turbine rotors; however, a test stand for these rotors is needed. Dr. Lemieux and the senior project team will design and build a test stand that will enable the simultaneous testing of two student-designed rotors at the existing wind turbine site. In addition to energy measurement, Lemieux emphasizes the importance of …

Treating Ground Water For Agricultural And Individual Consumption, Gabby Miller, Bronson Scott, Michael Clawson

Biomedical Engineering

This project, conducted in collaboration with Cal Poly seniors and Da Vinci High School students, aims to develop a solar-powered groundwater purification system. This system is designed to provide clean water for agricultural use and individual consumption, addressing the growing concerns of groundwater contamination and accessibility needs. The final prototype integrates a gravity filtration system combined with chemical purification, utilizing aluminum sulfate and chlorine to remove particulates, bacteria, and organic compounds.

The research phase involved an extensive review of groundwater contamination issues, existing filtration technologies, and market analysis. Key design constraints included cost-effectiveness, ease of maintenance, and minimal energy consumption, …

Design, Test, And Comparison Of A Photovoltaic Thermal Hybrid Solar Collector Utilizing A Thermosiphon, And Theory And Analysis Of Related Predictive Computer Model, Lance Brown

Master's Theses

Design, construction and testing of a photovoltaic thermal collector, or PVT, was completed to determine efficiency improvements of this system compared to a conventional solar panel and to find the thermal energy gained through hot water storage. Flow, driven by density changes from solar radiation, creates a thermosiphon, moving water without the use of a pump and ultimately drawing heat away from the solar panel. This is done to create a more efficient solar panel as well as decreasing potential damage due to high temperatures. Evaluation of electrical efficiency, thermal efficiency and flowrate allow for comparison between other PVT systems. …

Rover Chassis & Suspension, Nikki Zainer, Aung Bhone Zaw, Joelle Romero, Colin Thompson

Mechanical Engineering

The Mars rover project is part of the University Rover Challenge (URC), a robotics competition organized by the Mars Society that tasks student teams with designing and building the next generation of Mars rovers. Cal Poly Human Space Technology and Research (CP-HSTAR) has inherited a rover developed by a previous senior design team.

This report documents the progress made in refining the rover’s structure, highlighting key specifications, and detailing design improvements aimed at enhancing the suspension’s structural integrity, improving wheel traction, increasing modularity, and developing an enclosed chassis for electronic components.

This report includes a detailed breakdown of the rover’s …

Design, Manufacturing, And Assembly Of Modular Snake-Like Robotic Arm, Alongside Design And Implementation Of System’S Digital-Twin, Scott Brown

Master's Theses

A unique modular snake-like robotic arm, also referred to as MA\RS – the Modular Arm \ Robotic System - was designed, manufactured, assembled, simulated, and programmed to create a modular robot which could move to a desired end position given the number of links, the position of the end link and the duration of motion. This robotic arm serves as the start of research into a modular space robotic system to be used in low-gravity environments. As such, this project focused on developing the initial design of the robot and its digital twin. The system’s modularity allows for changes to …