Mechanical Engineering Commons^™

Particle Modeling Of Non-Equilibrium Field Emission Driven Rf Microplasmas, Siva Sashank Tholeti

Open Access Dissertations

Non-equilibrium microplasmas at atmospheric pressures have been investigated for active flow control, micropropulsion and electronic display applications to name a few. The operational voltages for these microplasmas are on the order of kilovolts. When the electric field at the electrodes reaches GV/m or tens of GV/m either due to reduced interelectrode spacing and surface irregularities or due to carefully designed nanostructures on the electrodes, quantum processes such as field emission and field ionization come into effect. These can potentially reduce the operational voltages of microplasma devices by an order of magnitude. Due to the rarefied and non-equilibrium nature of these …

Data Driven Low-Bandwidth Intelligent Control Of A Jet Engine Combustor, Nathan L. Toner

Open Access Dissertations

This thesis introduces a low-bandwidth control architecture for navigating the input space of an un-modeled combustor system between desired operating conditions while avoiding regions of instability and blow-out. An experimental procedure is discussed for identifying regions of instability and gathering sufficient data to build a data-driven model of the system's operating modes. Regions of instability and blow-out are identified experimentally and a data-driven operating point classifier is designed. This classifier acts as a map of the operating space of the combustor, indicating regions in which the flame is in a "good" or "bad" operating mode. A data-driven predictor is also …

Implementing And Testing A Panel-Based Method For Modeling Acoustic Scattering From Cfd Input, S. Hales Swift

Open Access Dissertations

Exposure of sailors to high levels of noise in the aircraft carrier deck environment is a problem that has serious human and economic consequences. A variety of approaches to quieting exhausting jets from high-performance aircraft are undergoing development. However, testing of noise abatement solutions at full-scale may be prohibitively costly when many possible nozzle treatments are under consideration. A relatively efficient and accurate means of predicting the noise levels resulting from engine-quieting technologies at personnel locations is needed. This is complicated by the need to model both the direct and the scattered sound field in order to determine the resultant …

Delay-Independent Stability Analysis Of Linear Time-Delay Systems Based On Frequency, Xianwei Li, Huijun Gao, Keqin Gu

SIUE Faculty Research, Scholarship, and Creative Activity

This paper studies strong delay-independent stability of linear time-invariant systems. It is known that delay-independent stability of time-delay systems is equivalent to some frequency-dependent linear matrix inequalities. To reduce or eliminate conservatism of stability criteria, the frequency domain is discretized into several sub-intervals, and piecewise constant Lyapunov matrices are employed to analyze the frequency-dependent stability condition. Applying the generalized Kalman–Yakubovich–Popov lemma, new necessary and sufficient criteria are then obtained for strong delay-independent stability of systems with a single delay. The effectiveness of the proposed method is illustrated by a numerical example.

Ionic Polymer-Metal Composite Actuators Based On Nafion Blends With Functional Polymers, Jungsoo Nam

UNLV Theses, Dissertations, Professional Papers, and Capstones

Ionic polymer metal composites (IPMCs) have been an attractive research subject for use in underwater robotic applications, biomedical and biomimetic application owing to their great potential as actuators, artificial muscles, and more. IPMC is synthetic composite nanomaterial of ion exchange membranes and metal electrode. Although both components are important, the properties of ion exchange membranes should be emphasized since it is responsible of the path for the mobile ions to migrate when voltage is applied to exhibit deformation. Most of the researches that have been done on IPMCs used commercially available Nafion as their ion exchange membranes. However, its high …

Effects Of Emf Emissions From Undersea Electric Cables On Coral Reef Fishes, Robert F. Jermain

HCNSO Student Theses and Dissertations

The objective of this project was to determine if the electromagnetic field (EMF) emissions from undersea power cables impacted the local and transient marine life, with an emphasis on reef fishes. The work was done at South Florida Ocean Measurement Facility of Naval Surface Warfare Center, Carderock Division, Broward County, Florida. This facility functions as the hub for a range of active undersea detection and data transmission cables. It has multiple active submarine power cables that extend several miles offshore and which can deliver power and enable data transmission to and from a range of acoustic and EMF sensors. The …

Experimental Investigation And Numerical Simulation Of A Copper Micro-Channel Heat Exchanger With Hfe-7200 Working Fluid, Eric Borquist

Doctoral Dissertations

Ever increasing cost and consumption of global energy resources has inspired the development of energy harvesting techniques which increase system efficiency, sustainability, and environmental impact by using waste energy otherwise lost to the surroundings. As part of a larger effort to produce a multi-energy source prototype, this study focused on the fabrication and testing of a waste heat recovery micro-channel heat exchanger. Reducing cost and facility requirements were a priority for potential industry and commercial adoption of such energy harvesting devices. During development of the micro-channel heat exchanger, a new fabrication process using mature technologies was created that reduced cost, …

Simulation Model Of An Automatic Commercial Ice Machine, Haithem Murgham, David Myszka, Vijay Bahel, Rajan Rajendran, Kurt Knapke, Suresh Shivashankar, Kyaw Wynn

Mechanical and Aerospace Engineering Faculty Publications

Automatic commercial ice-making machines that produce a batch of cube ice at regular intervals are known as “cubers." Such machines are commonly used in food service, food preservation, hotel, and health service industries. The machines are typically rated for the weight of ice produced over a 24-hour period at ambient air temperatures of 90°F and water inlet temperature of 70°F.

These cubers typically utilize an air-cooled, vapor-compression cycle to freeze circulating water flowing over an evaporator grid. Once a sufficient amount ice is formed, a valve switches to enable a harvest mode, where the compressor’s discharge gas is routed into …

Large Length Scale Capillary Fluidics: From Jumping Bubbles To Drinking In Space, Andrew Paul Wollman

Dissertations and Theses

In orbit, finding the "bottom" of your coffee cup is a non-trivial task. Subtle forces often masked by gravity influence the containment and transport of fluids aboard spacecraft, often in surprising non-intuitive ways. Terrestrial experience with capillary forces is typically relegated to the micro-scale, but engineering community exposure to large length scale capillary fluidics critical to spacecraft fluid management design is low indeed. Low-cost drop towers and fast-to-flight International Space Station (ISS) experiments are increasing designer exposure to this fresh field of study. This work first provides a wide variety of drop tower tests that demonstrate fundamental and applied capillary …

Analysis Of A Parallel Machine Scheduling Problem With Sequence Dependent Setup Times And Job Availability Intervals, Ridvan Gedik, Chase Rainwater, Heather Nachtmann, Edward A. Pohl

Mechanical and Industrial Engineering Faculty Publications

In this study, we propose constraint programming (CP) model and logic-based Benders algorithms in order to make the best decisions for scheduling non-identical jobs with availability intervals and sequence dependent setup times on unrelated parallel machines in a fixed planning horizon. In this problem, each job has a profit, cost and must be assigned to at most one machine in such a way that total profit is maximized. In addition, the total cost has to be less than or equal to a budget level. Computational tests are performed on a real-life case study prepared in collaboration with the U.S. Army …

Experimental Building Demonstration Model With Viscous Fluid Dampers, Blake Thomas Reeve, Brianna Jean Kufa, Aden Malek Stepanians, Sophie Carmion Ratkovich

Architectural Engineering

The Architectural Engineering major places a heavy emphasis on structural dynamics and the role of wind and seismic loading in building analysis and design. Buildings of high importance that are critical to community function, such as hospitals, often utilize supplemental damping devices like supplemental viscous fluid dampers or base isolators to reduce the overall demands on the structural system. The design and analysis of these dampers are typically not taught at the undergraduate level, and is frequently performed by mechanical engineers, in lieu of structural engineers.

To better understand and research building behavior with supplemental damping devices, our multi-disciplinary team …

Metals Additive Manufacturing Powder Aging Characterization, Thomas Russell Lovejoy, Nicholas Karl Muetterties, David Takeo Otsu

Mechanical Engineering

The metallic additive manufacturing process known as selective laser melting requires highly spherical, normally distributed powder with diameters in the range of 10 to 50 microns. Previous observations have shown a degradation in powder quality over time, resulting in unwanted characteristics in the final printed parts. 21-6-9 stainless steel powder was used to fabricate test parts, with leftover powder recycled back into the machine. Powder samples and test specimens were characterized to observe changes across build cycles. Few changes were observed in the physical and mechanical properties of the specimens, however, there were indications of chemical changes across cycles. Potential …

Bunch Splitting Simulations For The Jleic Ion Collider Ring, R. Gamage, T. Satogata

Physics Faculty Publications

We describe the bunch splitting strategies for the proposed JLEIC ion collider ring at Jefferson Lab. This complex requires an unprecedented 9:6832 bunch splitting, performed in several stages. We outline the problem and current results, optimized with ESME including general parameterization of 1:2 bunch splitting for JLEIC parameters.

How Can Occupancy Modeling And Occupancy Sensors Reduce Energy Usage In Academic Buildings: An Application Approach To University Of San Francisco, Paloma R. Duong

Master's Projects and Capstones

Buildings are amongst the highest energy consumers relative to industry and transportation. They account for 40% of the world’s energy consumption, due to the need for lighting, equipment, heating, cooling and ventilation. Academic buildings are multi-purpose buildings that create a challenge on energy reduction. Most are old and have fixed occupancy schedules, resulting in high energy consumption because these buildings experience significant occupancy variation throughout the day. Five academic buildings were analyzed; their building information, energy consumption data and methods to project energy savings have been analyzed. The case studies presented different strategies on predicting energy savings, but these have …

Measuring Accuracy Of Two 3d Printing Materials, Mudassir Ali

Master of Technology Management Plan II Graduate Projects

Part accuracy is one of the important aspect in the manufacturing industry. The overall inaccuracy of the parts being built by RP technology has been one of the major challenges that need to be overcome. Though all the printing materials come with specifications, but the suppliers and manufactures does not specify the accuracy of the materials. In this study we established a study which compares the accuracy of the materials in consideration and performed an experiment to establish the superiority of a material in terms of accuracy over each other. The purpose of this project was to compare the dimensional …

College Of Engineering Senior Design Competition Spring 2016, University Of Nevada, Las Vegas

Fred and Harriet Cox Senior Design Competition Projects

Part of every UNLV engineering student’s academic experience, the senior design project stimulates engineering innovation and entrepreneurship. Each student in their senior year chooses, plans, designs, and prototypes a product in this required element of the curriculum. A capstone to the student’s educational career, the senior design project encourages the student to use everything learned in the engineering program to create a practical, real world solution to an engineering challenge. The senior design competition helps focus the senior students in increasing the quality and potential for commercial application for their design projects. Judges from local industry evaluate the projects on …

Satellite Retrievals Of Karenia Brevis Harmful Algal Blooms In The West Florida Shelf Using Neural Networks And Comparisons With Other Techniques, Ahmed El-Habashi, Ioannis Ioannou, Michelle Tomlinson, Richard P. Stumpf, Sam Ahmed

Publications and Research

We describe the application of a Neural Network (NN) previously developed by us, to the detection and tracking, of Karenia brevis Harmful Algal Blooms (KB HABs) that plague the coasts of the West Florida Shelf (WFS) using Visible Infrared Imaging Radiometer Suite (VIIRS) satellite observations. Previous approaches for the detection of KB HABs in the WFS primarily used observations from the Moderate Resolution Imaging Spectroradiometer Aqua (MODIS-A) satellite. They depended on the remote sensing reflectance signal at the 678 nm chlorophyll fluorescence band (Rrs678) needed for both the normalized fluorescence height (nFLH) and Red Band Difference algorithms (RBD) currently used. …

Optical Analysis And Fabrication Of Micro And Nanoscale Plasmonically Enhanced Devices, Avery M. Hill

Physics Undergraduate Honors Theses

Plasmonic nanostructures have been shown to act as optical antennas that enhance optical devices due to their ability to focus light below the diffraction limit of light and enhance the intensity of the incident light. This study focuses on computational electromagnetic (CEM) analysis of two devices: 1) GaAs photodetectors with Au interdigital electrodes and 2) Au thin-film microstructures. Experiments showed that the photoresponse of the interdigital photodetectors depend greatly on the electrode gap and the polarization of the incident light. Smaller electrode gap and transverse polarization give rise to a larger photoresponse. It was also shown that the response from …

Optical Analysis And Fabrication Of Micro And Nanoscale Plasmonically Enhanced Devices, Avery M. Hill

Mechanical Engineering Undergraduate Honors Theses

Plasmonic nanostructures have been shown to act as optical antennas that enhance optical devices due to their ability to focus light below the diffraction limit of light and enhance the intensity of the incident light. This study focuses on computational electromagnetic (CEM) analysis of two devices: 1) GaAs photodetectors with Au interdigital electrodes and 2) Au thin-film microstructures. Experiments showed that the photoresponse of the interdigital photodetectors depend greatly on the electrode gap and the polarization of the incident light. Smaller electrode gap and transverse polarization give rise to a larger photoresponse. It was also shown that the response from …

Haul Truck Tires Recycling, Jessica N. Lizarazu

Chemical Engineering Undergraduate Honors Theses

The disposal of large Off-the-Road (OTR) tires is an increasingly important concern. These tires can weigh up to 8,450 pounds with an overall diameter and width of approximately 140.7 inches and 45.1 inches respectively. OTR tires are used for mining vehicles such as haul trucks, wheel loaders, backhoes, graders, and trenchers. These new tires cost between $38,000 and $50,000 each, depending on multiple factors including oil prices and the cyclical nature of the industry. Haul trucks contain six tires per vehicle, and mines replace these tires around every 9-12 months. Statistics regarding discarded OTR tires are not provided by the …

Cfd Model For Ventilation In Broiler Holding Sheds, Christian Heymsfield

Biological and Agricultural Engineering Undergraduate Honors Theses

Broiler production in Arkansas was valued at over $3.6 billion in 2013 (University of Arkansas Extension of Agriculture). Consequently, improvement in any phase of the production process can have significant economic impact and animal welfare implications. From the time poultry leave the farm and until they are slaughtered, they can be exposed to harsh environmental conditions, both in winter and in summer. After road transportation, birds are left to wait in holding sheds once they arrive at the processing plant, for periods of approximately 30 minutes to two hours. This project was interested in this holding shed waiting time during …

Particle Image Velocimetry Design & Installation, Zach Ritchie

Mechanical Engineering Undergraduate Honors Theses

This work will mainly focus on the design, construction, and installation of the Particle Image Velocimetry (PIV) system in the Chemical Hazards Research Center wind tunnel. The PIV system utilizes a Class IV (double pulsed) laser, optics to produce a light sheet, timing circuitry, and a high-resolution camera (with buffered output) to measure a system’s velocity (two-dimensional) field by determining the displacement of particles over the time between laser pulses. For maximum mobility and functionality, the PIV system was installed in the center of the tunnel on a moveable cart with the laser and camera mounted to an adjustable support. …

Investigating The Effect Of Carbon Nanotube Functionalization In A Polydimethylsiloxane Composite Through Use Of A Stepped Bar Apparatus, Matthew I. Ralphs

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Thermal interface materials (TIMs) are used in transporting heat away from a circuit or electronic module. Composite materials are a popular research area for TIMs because they allow the desired properties to be joined in a composite to take advantage of the best properties from all the constituents involved. The composite selected for this study uses carbon nanotubes (CNT) as the filler and an elastomeric polymer for the matrix, specifically a multiwalled carbon nanotube (MWCNT) / polydimethylsiloxane (PDMS) composite. This study looks at chemical modification (functionalization) of the CNTin an effort to produce a better bond between the CNT and …

Neutron-Gamma Discrimination In Elpasolite Scintillator Detector, Brittany Morgan

UNLV Theses, Dissertations, Professional Papers, and Capstones

Existing nuclear stockpiles and weapons-making capabilities imperil the global community. Current nonproliferation efforts involve the research and development of newer, more efficient detection systems that can be deployed for the interdiction and monitoring of special nuclear materials (SNM). Spontaneous and induced fission events in SNM produce neutrons and gamma rays, which can be detected and analyzed, in particular, using scintillator detectors. Various electronic data acquisition systems and data analysis methods have been employed to record and characterize neutron and photon signatures. The goal of this thesis is to develop a new method of discrimination between neutrons and photons in the …

On The Scattering Of An Acoustic Plane Wave By A Soft Prolate Spheroid, Joseph Michael Borromeo

UNLV Theses, Dissertations, Professional Papers, and Capstones

This thesis solves the scattering problem in which an acoustic plane wave of propagation number K1 is scattered by a soft prolate spheroid. The interior field of the scatterer is characterized by a propagation number K2, while the field radiated by the scatterer is characterized by the propagation number K3. The three fields and their normal derivatives satisfy boundary conditions at the surface of the scatterer. These boundary conditions involve six complex parameters depending on the propagation numbers. The scattered wave also satisfies the Sommerfeld radiation condition at infinity. Through analytical methods, series representations are constructed for the interior field …

Thermal Property Measurement Of Thin Fibers By Complementary Methods, Troy Robert Munro

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Thin fibers are prevalent in many engineering materials. Measuring how well heat transfers in such small fibers can be difficult to determine, and previous methods have led to erroneous results. This dissertation details three proposed methods to improve the measurement of the thermal conductivity, thermal diffusivity, and volumetric heat capacity of thin fibers. Of particular interest is natural and synthetic spider silks because previously published values of the natural silk thermal conductivity was similar to copper, an excellent thermal conductor.

The three methods developed are the improved transient electrothermal technique (which was redeveloped to include radiation and convection heat losses …

Method For Determining Time-Resolved Heat Transfer Coefficient And Adiabatic Effectiveness Waveforms With Unsteady Film Cooling, James L. Rutledge, Jonathan F. Mccall

AFIT Patents

A new method for determining heat transfer coefficient (h) and adiabatic effectiveness (η) waveforms h(t) and η(t) from a single test uses a novel inverse heat transfer methodology to use surface temperature histories obtained using prior art approaches to approximate the h(t) and η(t) waveforms. The method best curve fits the data to a pair of truncated Fourier series.

Parametric Analysis Of A Solid Oxide Fuel Cell Auxiliary Power Unit Operating On Syngas Produced By Autothermal Reforming Of Hydrocarbon Fuels, Jun Dong, Xinhai Xu, Ben Xu, Shuyang Zhang

Mechanical Engineering Faculty Publications

A 1 kWe integrated auxiliary power unit (APU) system consisting of an autothermal reformer and a solid oxide fuel cell (SOFC) unit, as well as balance-of-plant components, was designed and analyzed. A relatively easy-to-approach SOFC model was developed in order to conveniently calculate V-I and P-I curves and the system's net efficiency at different operating conditions. The effects of steam to carbon and oxygen to carbon ratios in the reactants, channel dimensions of the SOFC unit, and hydrocarbon fuel types on the integrated APU system's performance were discussed. Five hydrocarbon fuels including diesel, Jet-A, gasoline, ethanol, and methanol were studied …

Spatio-Temporal Linear Stability Analysis Of Stratified Planar Wakes: Velocity And Density Asymmetry Effects, Benjamin Emerson, Swapnil Jagtap, J. Mathew Quinlan, Michael W. Renfro, Baki M. Cetegen, Tim Lieuwen

Mechanical Engineering Faculty Publications

This paper explores the hydrodynamic stability of bluff body wakes with non-uniform mean density, asymmetric mean density, and velocity profiles. This work is motivated by experiments [S. Tuttle et al., “Lean blow off behavior of asymmetrically-fueled bluff body-stabilized flames,” Combust. Flame 160, 1677 (2013)], which investigated reacting wakes with equivalence ratio stratification and, hence, asymmetry in the base flow density profiles. They showed that highly stratified cases exhibited strong, narrowband oscillations, suggestive of global hydrodynamic instability. In this paper, we present a local hydrodynamic stability analysis for non-uniform density wakes that includes base flow asymmetry. The results show …

Secondary Electron Emission From Plasma Processed Accelerating Cavity Grade Niobium, Miloš Bašović

Mechanical & Aerospace Engineering Theses & Dissertations

Advances in the particle accelerator technology have enabled numerous fundamental discoveries in 20th century physics. Extensive interdisciplinary research has always supported further development of accelerator technology in efforts of reaching each new energy frontier.

Accelerating cavities, which are used to transfer energy to accelerated charged particles, have been one of the main focuses of research and development in the particle accelerator field. Over the last fifty years, in the race to break energy barriers, there has been constant improvement of the maximum stable accelerating field achieved in accelerating cavities. Every increase in the maximum attainable accelerating fields allowed for higher …