Mechanical Engineering Commons^™

Benchmark Burnishing With Almen Strip For Surface Integrity, Z. Y. Liu, C. H. Fu, M. P. Sealy, Y. Zhao, Y. B. Guo

Department of Mechanical and Materials Engineering: Faculty Publications

Burnishing is a surface treatment process widely used in aerospace, navy and other industries to improve fatigue and corrosion resistance by introducing a compressive residual stress layer. The measurement of residual stress by XRD is expensive, time consuming, and tedious. This work presented a quick method to determine the residual stress by using Almen strips. Inspired by the application of Almen strips in shot peening, deflections of burnished Almen strips under different burnishing conditions were measured. It was found that the deflection of Almen strip reflects the magnitude and penetration depth into subsurface of induced stress. Higher burnishing force, smaller …

Effects Of Aspect Ratio On The Mode Couplings Of Thin-Film Bulk Acoustic Wave Resonators, Nian Li, Zhenghua Qian, Jiashi Yang

Department of Mechanical and Materials Engineering: Faculty Publications

We studied mode couplings in thin film bulk acoustic wave resonators of a piezoelectric film on a dielectric layer operating with the fundamental thickness-extensional mode. A system of plate equations derived in our previous paper was used which includes the couplings to the unwanted in-plane extension, flexure, fundamental and second-order thickness shear modes. It was shown that the couplings depend strongly on the plate length/thickness ratio. For a relatively clean operating mode with weak couplings to unwanted modes, a series of discrete values of the plate length/thickness ratio should be avoided and these values were determined in the present paper. …

Clustering On Magnesium Surfaces – Formation And Diffusion Energies, Haijian Chu, Hanchen Huang, Jian Wang

Department of Mechanical and Materials Engineering: Faculty Publications

The formation and diffusion energies of atomic clusters on Mg surfaces determine the surface roughness and formation of faulted structure, which in turn affect the mechanical deformation of Mg. This paper reports first principles density function theory (DFT) based quantum mechanics calculation results of atomic clustering on the low energy surfaces {0001} and {1011}. In parallel, molecular statics calculations serve to test the validity of two interatomic potentials and to extend the scope of the DFT studies. On a {0001} surface, a compact cluster consisting of few than three atoms energetically prefers a facecentered- cubic stacking, to serve as a …

Review Of Sustainability Issues In Non-Traditional Machining Processes, Kamlakar Rajurkar, H. Hadidi, J. Pariti, G. C. Reddy

Department of Mechanical and Materials Engineering: Faculty Publications

Non-traditional machining processes (such as EDM and ECM) provide alternatives or sometimes the only alternative in generating highly complex 3-D features in very difficult-to -machine materials. This paper reviews recently published work on sustainability issues related to these processes. For example in Electrochemical machining (ECM) the effect of sludge generation and selection of dielectric in Electrodischarge machining (EDM) need to be investigated from the sustainability point of view. All processes need to be studied not only for resulting productivity and accuracy but also their environmental impact during product generation and usage. This paper addresses process mechanisms, surface integrity, sensing and …

Accommodation Of The Human Lens Capsule Using A Finite Element Model Based On Nonlinear Regionally Anisotropic Biomembranes, G. David, Ryan M. Pedrigi, J. D. Humphrey

Department of Mechanical and Materials Engineering: Faculty Publications

Accommodation of the eyes, the mechanism that allows humans to focus their vision on near objects, naturally diminishes with age via presbyopia. People who have undergone cataract surgery, using current surgical methods and artificial lens implants, are also left without the ability to accommodate. The process of accommodation is generally well known; however the specific mechanical details have not been adequately explained due to difficulties and consequences of performing in vivo studies. Most studies have modeled the mechanics of accommodation under assumptions of a linearly elastic, isotropic, homogenous lens and lens capsule. Recent experimental and numerical studies showed that the …

Growth Mechanisms Of Multiscale, Mound-Like Surface Structures On Titanium By Femtosecond Laser Processing, Edwin Peng, Ryan Bell, Craig A. Zuhlke, Meiyu Wang, Dennis R. Alexander, George Gogos, Jeffrey E. Shield

Department of Mechanical and Materials Engineering: Faculty Publications

Femtosecond laser surface processing (FLSP) can be used to functionalize many surfaces, imparting specialized properties such as increased broadband optical absorption or superhydrophobicity/-hydrophilicity. In this study, the subsurface microstructure of a series of mound-like FLSP structures formed on commercially pure titanium using five combinations of laser fluence and cumulative pulse counts was studied. Using a dual beam Scanning Electron Microscope with a Focused Ion Beam, the subsurface microstructure for each FLSP structure type was revealed by cross-sectioning. The microstructure of the mounds formed using the lowest fluence value consists of the original Ti grains. This is evidence that preferential laser …

Design And Field Testing Of A Combined Flaming And Cultivation Implement For Effective Weed Control, Brian D. Neilson, Chris A. Bruening, Strahinja Stepanovic, Avishek Datta, Stevan Z. Knezevic, George Gogos

Department of Mechanical and Materials Engineering: Faculty Publications

Flaming is a thermal weed control method that uses heat to control weeds within or between crop rows. Mechanical cultivation is another weed control method which undercuts weeds between crop rows, while leaving a strip of weeds within the crop row. A combination flamer/cultivator implement was designed to take advantage of the good qualities of both flaming and cultivation methods to provide a more consistent weed control than using either flaming or mechanical cultivation alone. Flaming hoods were designed in the spring of 2010 and retrofitted on an existing row crop cultivator. The flaming hoods were redesigned in the spring …

Robotic Surgical Devices, Systems, And Related Methods, Shane M. Farritor, Erik Mumm, Philip Chu, Nishant Kumar, Jason Dumpert, Yutaka Tsutano

Department of Mechanical and Materials Engineering: Faculty Publications

The embodiments disclosed herein relate to various medical device components, including components that can be incorporated into robotic and/or in vivo medical devices. Certain embodiments include various modular medical devices for in vivo medical procedures.

Methods , Systems , And Devices Relating To Surgical End Effectors, Shane M. Farritor, Tom Fredrick, Joe Bartels

Department of Mechanical and Materials Engineering: Faculty Publications

The embodiments disclosed herein relate to various medical device components, including components that can be incorporated into robotic and/or in vivo medical devices, and more specifically including end effectors that can be incorporated into such devices. Certain end effector embodiments include various vessel cautery devices that have rotational movement as well as cautery and cutting functions while maintaining a relatively compact structure. Other end effector embodiments include various end effector devices that have more than one end effector.

System For Imaging And Measuring Rail Deflection, Shane M. Farritor

Department of Mechanical and Materials Engineering: Faculty Publications

Devices, systems, and methods for imaging and measuring deflections in structures such as railroad rail are disclosed. One exemplary embodiment relates to a vision system having a high-speed, visible-light imaging camera and an evaluation unit configured for analyzing images from the camera to detect geometric variations in the structure. In a second example, additional sensors are used to identify the wheel location(s) in the same reference frame as the mea Surement system. In analyzing structures Such as railroad track rail, the imaging camera can be coupled to a moving rail vehicle and configured for generating images of the rail as …

Effect Of Random Ethylene Comonomer On Relaxation Of Flow-Induced Precursors In Isotactic Polypropylene, Benjamin Schammé, Eric Dargent, Lucia Fernandez-Ballester

Department of Mechanical and Materials Engineering: Faculty Publications

The effect of comonomer on structure and relaxation of flow-induced precursors was investigated in a series of isotactic polypropylene and random propylene−ethylene copolymers. The polymers were subjected to flow by fiber pulling and allowed to relax above their nominal melting temperature for specific times. The type of morphology developed after cooling revealed whether flow-induced precursors were still present or the melt had fully reequilibrated. Precursors were long-lived and, at fixed temperature, decayed significantly faster with higher ethylene content. The critical time for precursor relaxation followed an Arrhenius-type dependence with temperature. The apparent energy of activation for precursor dissolution decreased with …

Rapidly Solidified Rare-Earth Permanent Magnets: Processing, Properties, And Applications, Shampa Aich, Dillip K. Satapathy, Jeffrey E. Shield

Department of Mechanical and Materials Engineering: Faculty Publications

Rapidly solidified rare-earth-based permanent magnets are considered to have better potential as permanent magnets compared to the conventional bulk materials, which can be attributed to their improved microstructure and better magnetic properties compared to rare-earth magnets synthesized by the conventional (powder metallurgy) routes. The performance (quality) of these magnets depends on the thermodynamics and kinetics of the different processing routes, such as atomization, melt spinning, and melt extraction. Here, we review the various processing routes of rapidly solidified rare-earth permanent magnets and the related properties and applications. In the review, some specific alloy systems, such as Sm–Co-based alloys, Nd–Fe–B, and …

Biodegradable Elastic Nanofibrous Platforms With Integrated Flexible Heaters For On-Demand Drug Delivery, Ali Tamayol, Alireza Hassani Najafabadi, Pooria Mostafalu, Ali K. Yetisen, Mattia Commotto, Musab Aldhahri, Mohamed Shaaban Abdel-Wahab, Zeynab Izadi Najafabadi, Shahrzad Latifi, Mohsen Akbari, Nasim Annabi, Seok Hyun Yun, Adnan Memic, Mehmet R. Dokmeci, Ali Khademhosseini

Department of Mechanical and Materials Engineering: Faculty Publications

Delivery of drugs with controlled temporal profiles is essential for wound treatment and regenerative medicine applications. For example, bacterial infection is a key challenge in the treatment of chronic and deep wounds. Current treatment strategies are based on systemic administration of high doses of antibiotics, which result in side effects and drug resistance. On-demand delivery of drugs with controlled temporal profile is highly desirable. Here, we have developed thermally controllable, antibiotic-releasing nanofibrous sheets. Poly(glycerol sebacate)- poly(caprolactone) (PGS-PCL) blends were electrospun to form elastic polymeric sheets with fiber diameters ranging from 350 to 1100 nm and substrates with a tensile modulus …

Nondestructive Testing System Design For Biological Product Based On Vibration Signal Analysis Of Acceleration Sensor, Xiaohao Li, Tao Shen

Department of Mechanical and Materials Engineering: Faculty Publications

In order to reduce the disadvantages of current biological product quality testing methods, taking the quality testing in cocoon trade markets as an example, this paper has proposed a quality nondestructive testing method for biological products based on the analysis of vibration signal from acceleration sensors. According to the wavelet transformation analysis on the random vibration signal acquired from the acceleration sensor, the random vibration signal related to the silkworm chrysalis quality has been analyzed and reconstructed; then the characteristic values such as: mean value, variance, mean square root, waveform index, pulse factor, and so on of the quality signal …

Solution Nuclear Magnetic Resonance Spectroscopy On A Nanostructured Diamond Chip, P. Kehayias, A. Jarmola, N. Mosavian, I. Fescenko, F.M. Benito, A. Laraoui, J. Smits, L. Bougas, D. Budker, A. Neumann, S.R.J. Brueck, V.M. Acosta

Department of Mechanical and Materials Engineering: Faculty Publications

Sensors using nitrogen-vacancy centers in diamond are a promising tool for small-volume nuclear magnetic resonance (NMR) spectroscopy, but the limited sensitivity remains a challenge. Here we show nearly two orders of magnitude improvement in concentration sensitivity over previous nitrogen-vacancy and picoliter NMR studies. We demonstrate NMR spectroscopy of picoliter-volume solutions using a nanostructured diamond chip with dense, high-aspect-ratio nanogratings, enhancing the surface area by 15 times. The nanograting sidewalls are doped with nitrogen-vacancies located a few nanometers from the diamond surface to detect the NMR spectrum of roughly 1 pl of fluid lying within adjacent nanograting grooves. We perform 1H …

Micro/Nanostructures Formation By Femtosecond Laser Surface Processing On Amorphous And Polycrystalline Ni60nb40, Edwin Peng, Alfred Tsubaki, Craig A. Zuhlke, Meiyu Wang, Ryan Bell, Michael J. Lucis, Troy P. Anderson, Dennis R. Alexander, George Gogos, Jeffrey E. Shield

Department of Mechanical and Materials Engineering: Faculty Publications

Femtosecond laser surface processing is a technology that can be used to functionalize many surfaces, imparting specialized properties such as increased broadband optical absorption or superhydrophilicity/superhydrophobicity. In this study, two unique classes of surface structures, below surface growth (BSG) and above surface growth (ASG) mounds, were formed by femtosecond laser surface processing on amorphous and polycrystalline Ni₆₀Nb₄₀ with two different grain sizes. Cross sectional imaging of these mounds revealed thermal evidence of the unique formation processes for each class of surface structure. BSG mounds formed on all three substrates using the same laser parameters had similar surface …

Methods , Systems , And Devices Relating To Robotic Surgical Devices , End Effectors , And Controllers, Shane M. Farritor, Thomas Frederick, Joe Bartels, Eric Markvicka, Jack Mondry

Department of Mechanical and Materials Engineering: Faculty Publications

The various embodiments disclosed herein relate to improved robotic surgical systems, including robotic surgical devices having improved arm components and/or bio metric sensors, contact detection systems for robotic surgical devices, gross positioning systems and devices for use in robotic surgical systems, and improved external controllers and consoles.

Toward Human-Like Automated Driving: Learning Spacing Profiles From Human Driving Data, Syed Ali

Wayne State University Dissertations

For automated driving vehicles to be accepted by their users and safely integrate with traffic involving human drivers, they need to act and behave like human drivers. This not only involves understanding how the human driver or occupant in the automated vehicle expects their vehicle to operate, but also involves how other road users perceive the automated vehicle’s intentions. This research aimed at learning how drivers space themselves while driving around other vehicles. It is shown that an optimized lane change maneuver does create a solution that is much different than what a human would do. There is a need …

Controlled Manipulation Of Floating Objects On Deformed Fluid Interfaces And Conditions For Stable Equilibria, Jose M. Carballo, Qi Ni, Jose Vasquez, Nathan B. Crane

Faculty Publications

At the millimeter scale, interactions between floating and semi-immersed objects are significant. The local curvature of the interface is modified by the weight/buoyancy forces of floating objects, and by the surface properties of semi-immersed objects. The curvature changes generate attractive (or repulsive) interactions between floating parts, and semi-immersed objects. This work demonstrates how electrowetting can manipulate these interactions in order to position, align, assemble and transport parts attached to the fluid interface. This demonstrates one way in which fluid interfaces can provide an alternative to standard pick and place technology for part positioning/assembly. Typically, the part/rod forces are purely attractive …

Human Centered Design Of An Open-Drum, Treadle Thresher For Quinoa Farmers In The Andes Of Northern Peru, Robert A. Hayes

Dissertations, Master's Theses and Master's Reports

Growing international demand for quinoa in recent years has led to increased production throughout its South American range, including the Peruvian Andes. Small-scale farmers, who are among the poorest Peruvians, are increasingly growing quinoa for both food security and economic benefit; however, manual harvesting activities, such as threshing, are labor-intensive and time-consuming. This report documents the design, construction and operation of prototype quinoa thresher in a rural village in Northern Peru. In addition, an overview of the history and evolutionary approach to design for the developing world is presented. From this overview, a series of criteria is considered for the …

The Emission And Particulate Matter Oxidation Performance Of A Scr Catalyst On A Diesel Particulate Filter With A Downstream Scr, Sagar Sharma

Dissertations, Master's Theses and Master's Reports

Selective catalytic reduction (SCR) systems along with a NH₃ slip control catalyst (ASC) offers NOₓ conversion efficiency >90 % with NH₃ slip < 20 ppm. However, future heavy duty diesel (HDD) engines are designed for higher engine-out NOₓ to improve fuel consumption. Consequently, there is a strong desire to further improve the NOₓ reduction performance of SCR systems, to meet the 2015 California Optional Low NOₓ Standard. SCR catalysts on a diesel particulate filter provide an effective solution to reduce NOₓ and PM using a single aftertreatment device. It also provides an opportunity to increase the SCR volume to achieve NOₓ conversion efficiency >95 %. A downstream SCR catalyst substrate can be used to get additional NO_x conversion by using the SCRF^® outlet NH₃ to increase the cumulative NOₓ conversion of the system.

In this study, NOₓ reduction, NH₃ slip and PM oxidation performance of a Cu-zeolite SCRF^® with a downstream Cu-zeolite SCR were investigated based on engine experimental data at steady state conditions. The experimental data were collected at varying SCRF^® inlet temperatures, space velocities, inlet …

Simulation Of Diesel Particulate Filter Regeneration Using Lattice Boltzmann Method, Kshitiz Kumar Jain

Dissertations, Master's Theses and Master's Reports

Lattice Boltzmann Method is a novel approach, which has shown promise in solving a wide variety of fluid flow problems including single and multi-phase flows in complex geometries. Volume elements of the fluid domain are considered to be composed of particles and these particles fall under a velocity distribution function at each grid point. Particles collide with each other under the influence of external forces and the rules of collision are defined so as to be compatible with the Navier-Stokes Equation. In the current work, LBM has been applied to Diesel Particulate filters which is a device used for reducing …

The Effect Of A Powered Ankle Foot Orthosis On Walking In A Stroke Subject: A Case Study, Ali Pourghasem, Ismail Ebrahimi Takamjani, Mohammad Taghi Karimi, Mohammad Kamali, Mohammad Jannesari, Iman Salafian

Department of Mechanical and Materials Engineering: Faculty Publications

[Purpose] Standing and walking are impaired in stroke patients. Therefore, assisted devices are required to restore their walking abilities. The ankle foot orthosis with an external powered source is a new type of orthosis. The aim of this study was to evaluate the performance of a powered ankle foot orthosis compared with unpowered orthoses in a stroke patient.

[Subjects and Methods] A single stroke subject participated in this study. The subject was fitted with three types of ankle foot orthosis (powered, posterior leg spring, and carbon ankle foot orthoses). He was asked to walk with and without the three types …

The Mars Desert Research Station - Erau Crew 160 Expedition, Lycourgos Manolopoulos, Ashley Hollis-Bussey, Hiroki Sugimoto, Cassandra Vella, John Herman, Marc Carofano

Student Works

The Mars Desert Research Station (MDRS) is a research program which is owned and operated by the Mars Society. The MDRS is located in Hanksville, Utah which hosts simulations that are typically two weeks long for professional scientists and engineers as well as college students of all levels, in training for human operations specifically on Mars. This space analog facility is in isolation, allowing for rigorous field studies regarding research that represents a true mission as if the crew members are conducting a real expedition on Mars. Participants are assigned specific roles and tasks that are typically aligned with their …

Attitude Determination Control Testing System (Helmholtz Cage And Air Bearing), Nicolas Theoret

Honors Theses

The WALI team at Western Michigan University requested a test environment to validate their CubeSat’s de-tumbling control system and hardware. The test environment required a Helmholtz cage and spherical air bearing. The Helmholtz cage provides an adjustable magnetic field to simulate low earth orbit; the spherical air bearing simulates the friction free environment the CubeSat will experience in space. In conjunction, the two components create an adjustable system that simulates a satellite in low earth orbit.

Photovoltaic Cooking In The Developing World, Tyler Watkins, Christopher O'Day, Omar Arriaga

Mechanical Engineering

The challenge of clean cooking is faced by hundreds of millions of people worldwide. We present a cooking technology consisting of a solar panel directly connected to an electric heater in a well-insulated chamber. Assuming continued decrease in solar panel prices, we anticipate that in a few decades Solar Electric Cooking technologies will be the most common cooking technology for the poor. Appropriate use of insulation reduces the power demand making low-power Insulated Solar Electric Cooking systems already cost competitive.

Android Drone: Remote Quadcopter Control With A Phone, Aubrey John Russell

Computer Engineering

The purpose of the “Android Drone” project was to create a quadcopter that can be controlled by user input sent over the phone’s Wi-Fi connection or 4G internet connection. Furthermore, the purpose was also to be able to receive live video feedback over the internet connection, thus making the drone an inexpensive option compared to other, equivalent drones that might cost thousands of dollars. Not only that, but the Android phone also has a host of other useful features that could be utilized by the drone: this includes GPS, pathing, picture taking, data storage, networking and TCP/IP, a Java software …

Haul Truck Tires Recycling, Omkar Bhave

Chemical Engineering Undergraduate Honors Theses

The disposal of large Off-the-Road (OTR) tires is an increasingly important concern. These tires can weigh up to 8,450 pounds with an overall diameter and width of approximately 140.7 inches and 45.1 inches respectively. OTR tires are used for mining vehicles such as haul trucks, wheel loaders, backhoes, graders, and trenchers.[1] These new tires cost between $38,000 and $50,000 each, depending on multiple factors including oil prices and the cyclical nature of the industry. Haul trucks contain six tires per vehicle, and mines replace these tires around every 9-12 months.[2] Statistics regarding discarded OTR tires are not provided by the …

Self-Patterning Gd Nano-Fibers In Mg-Gd Alloys, Yangxin Li, Jian Wang, Kaiguo Chen, Meiyue Shao, Yao Shen, Li Jin, Guo-Zhen Zhu

Department of Mechanical and Materials Engineering: Faculty Publications

Manipulating the shape and distribution of strengthening units, e.g. particles, fibers, and precipitates, in a bulk metal, has been a widely applied strategy of tailoring their mechanical properties. Here, we report self-assembled patterns of Gd nano-fibers in Mg-Gd alloys for the purpose of improving their strength and deformability. 1-nm Gd nano-fibers, with a 〈c〉-rod shape, are formed and hexagonally patterned in association with Gd segregations along dislocations that nucleated during hot extrusion. Such Gd-fiber patterns are able to regulate the relative activities of slips and twinning, as a result, overcome the inherent limitations in strength and ductility of Mg alloys. …

Single Site Robotc Device And Related Systems And Methods, Jack Mondry, Shane M. Farritor, Eric Markvicka, Thomas Frederick, Joseph Bartels

Department of Mechanical and Materials Engineering: Faculty Publications

The embodiments disclosed herein relate to various medical device components, including components that can be incor porated into robotic and/or in vivo medical devices. Certain embodiments include various medical devices for in vivo medical procedures.