Mechanical Engineering Commons^™

Coupled Dem-Fem For Dynamic Analysis Of Granular Systems In Bending, Kitti Rattanadit

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Characterizing the dynamic behavior of granular materials is one of the great challenges in the mechanics of granular matter. Methods for evaluating the mechanical properties of granular matter have applications in a variety of industries, mining and geotechnical activities, defense and military operations. A coupled 2D Discrete Element Method-Finite Element Method (DEM-FEM) code, called "BobKit", is developed and implemented for analyzing the behavior of a 2D granular layer on top of an elastic beam under deforming (quasi-static) or vibrating (dynamic) of the beam. The explicit time-integration dynamic code is used to simulate quasi-static and dynamic bending of the granular layer …

Luminescence Enhancement Of Cdte Nanostructures In Laf3:Ce/Cdte Nanocomposites, Mingzhen Yao, Xing Zhang, Lun Ma, Wei Chen, Alan G. Joly, Jinsong Huang, Qingwu Wang

Department of Mechanical and Materials Engineering: Faculty Publications

Radiation detection demands new scintillators with high quantum efficiency, high energy resolution, and short luminescence lifetimes. Nanocomposites consisting of quantum dots and Ce³⁺ doped nanophosphors may be able to meet these requirements. Here, we report the luminescence enhancement of LaF₃:Ce/CdTe nanocomposites which were synthesized by a wet chemistry method. CdTe quantum dots in LaF₃:Ce/CdTe nanocomposites are converted into nanowires, while in LaF₃ /CdTe nanocomposites no such conversion is observed. As a result, the CdTe luminescence in LaF₃:Ce/CdTe nanocomposites is enhanced about five times, while in LaF₃ /CdTe nanocomposites no enhancement was …

Sensitivity Analysis Of The Johnson-Cook Plasticity Model For Hypervelocity Impacts: A Hydro-Code Study, Carlos David Castellanos

Open Access Theses & Dissertations

Computer simulations have been in use for decades in the modeling of hypervelocity impacts and general large deformation problems. Several computer codes have been developed to simulate this type of problems under a variety of geometric configurations and for any number of materials. These codes make use of several constitutive material models to simulate the response of the material under a variety of thermo-mechanical conditions. The Johnson-Cook constitutive model is widely used in the simulation hypervelocity impacts for the simulation of crater formation and even perforation of target structures. This thesis presents the results of a sensitivity study of this …

Processing Of Zrb2-Zrc-Zrxsiy Ceramic By Reactive Metal Penetration, Nischel B. Maheswaraiah

Open Access Theses & Dissertations

The processing of ZrB2-ZrC-ZrxSiy composite by reactive metal penetration was investigated as a successor to the ZrB2-SiC composites for hypersonic vehicles application, which cannot be used for extended time at temperatures greater than 1600C due to formation of SiO and CO gases. Zirconium (Zr), zirconium disilicide (ZrSi2), and boron carbide (B4C) were reacted in graphite crucibles for 60, 120, 180, and 240 minutes. Microscopy and x-ray diffraction (XRD) deduced the formation of a heterogeneous microstructure of ZrB2-ZrC-ZrxSiy precipitates surrounded by a solidified Zr-Si melt. Unreacted boron carbide was observed in samples held at 1860C for 60 minutes and 120 minutes, …

Studies Of Dynamic Crack Propagation And Crack Branching With Peridynamics, Youn Doh Ha, Florin Bobaru

Department of Engineering Mechanics: Faculty Publications

In this paper we discuss the peridynamic analysis of dynamic crack branching in brittle materials and show results of convergence studies under uniform grid refinement (m-convergence) and under decreasing the peridynamic horizon (δ-convergence). Comparisons with experimentally obtained values are made for the crack-tip propagation speed with three different peridynamic horizons.We also analyze the influence of the particular shape of themicro-modulus function and of different materials (Duran 50 glass and soda-lime glass) on the crack propagation behavior. We show that the peridynamic solution for this problem captures all the main features, observed experimentally, of dynamic crack propagation and branching, as well …

Method Of Transferring Strained Semiconductor Structure, Michael Nastasi

Department of Mechanical and Materials Engineering: Faculty Publications

The transfer of strained semiconductor layers from one substrate to another substrate involves depositing a multilayer structure on a substrate having surface contaminants. An interface that includes the contaminants if formed in between the deposited layer and the substrate. Hydrogen atoms are introduced into the structure and allowed to diffuse to the interface. Afterward, the deposited multilayer structure is bonded to a second substrate and is separated away at the interface, which results in transferring a multilayer structure from one substrate at least one strained semiconductor layer and at least one strain-induced seed layer. The strain-induced seed layer can be …

Imprinting Polymerfilm On Patterned Substrate, Li Tan, Yen-Peng Kong, Stella W. Pang, Albert F. Yee

Department of Mechanical and Materials Engineering: Faculty Publications

A method of applying a pattern on a topography includes first applying a polymer film to an elastormer member, such as PDMS, to form a pad. The pad is then applied to a substrate having a varying topography under pressure. The polymer film is transferred to the substrate due to the plastic deformation of the polymer film under pressure compared to the elastic deformation of the PDMS member pulls away from the polymer layer, thereby depositing the polymer layer, thereby depositing the polymer layer upon the substrate.

Indentation Creep Analysis For Self Similar Indenters, Sandeep V. Thube

Mechanical & Aerospace Engineering Theses & Dissertations

In indentation creep experiments, it is difficult to characterize the mechanical properties of small size specimens using conventional methods. This study uses finite element modeling to investigate rate-sensitive deformation of materials with different hardness and strain rate sensitivities for self similar indenter tip geometries. The simulation model is developed using commercially available finite element software Abaqus/Standard. Our study investigates the difference between strain rate sensitivity of hardness (vH) and of flow stress (vu) and their relation to the hardness/modulus ratio. It reveals that the commonly held assumption that vH = vu is violated except for materials with low hardness/modulus …

Flexible Electronics Using Ion Implantation To Adhere Polymer Substrate To Single Crystal Silicon Substrate, Terry L. Alford, Douglas C. Thompson Jr., Hyunchul Kim, Michael A. Nastasi, James W. Mayer, Daniel Adams

Department of Mechanical and Materials Engineering: Faculty Publications

An electronic apparatus uses a single crystalline silicon Substrate disposed adjacent to a flexible substrate. The electronic apparatus may be a flexible flat panel display, or a flexible printed circuit board. The flexible substrate can be made from polymer, plastic, paper, flexible glass, and stainless steel. The flexible substrate is bonded to the single crystalline substrate using an ion implantation process. The ion implantation process involves the use of a noble gas Such as hydrogen, helium, Xenon, and krypton. A plurality of semiconductor devices are formed on the single crystalline silicon Substrate. The semi conductor devices may be thin film …

Performance Analysis Of Coal-Fired Boiler And Natural Gas Fired Boiler At Morehead State University, Devender Banne

Morehead State Theses and Dissertations

A thesis presented to the faculty of the College of Science & Technology at Morehead State University in partial fulfillment of the requirements for the Degree of Master of Science by Devender Banne on May 4, 2009.

Multiscale Modeling Of Impact On Heterogeneous Viscoelastic Solids With Evolving Microcracks, Flavio V. Souza

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Multiscale computational techniques play a major role in solving problems related to viscoelastic composite materials due to the complexities inherent to these materials. In the present work, a numerical procedure for multiscale modeling of impact on heterogeneous viscoelastic solids containing evolving microcracks is proposed in which the (global scale) homogenized viscoelastic incremental constitutive equations have the same form as the local scale viscoelastic incremental constitutive equations, but the homogenized tangent constitutive tensor and the homogenized incremental history dependent stress tensor depend on the amount of damage accumulated at the local scale. Furthermore, the developed technique allows the computation of the …

The Effect Of Silicon Content On Impact Toughness Of T91 Grade Steels, Ajit K. Roy, Pankaj Kumar, Debajyoti Maitra

Mechanical Engineering Faculty Research

The impact resistance of silicon (Si)-containing modified 9Cr-1Mo steels has been investigated within a temperature regime of -40 to 440°C using the Charpy method. The results indicate that the energies absorbed in fracturing the tested specimens were substantially lower at temperatures of -40, 25, and 75°C compared to those at elevated temperatures. Lower impact energies and higher ductile-to-brittle-transition-temperatures (DBTTs) were observed with the steels containing 1.5 and 1.9 wt.% Si. The steels containing higher Si levels exhibited both ductile and brittle failures at elevated temperatures. However, at lower temperatures, brittle failures characterized by cleavage and intergranular cracking were observed for …

Identification Of Multiple Oscillation States Of Carbon Nanotube Tipped Cantilevers Interacting With Surfaces In Dynamic Atomic Force Microscopy, Mark Strus, Arvind Raman

Birck and NCN Publications

Carbon nanotubes (CNTs) have gained increased interest in dynamic atomic force microscopy (dAFM) as sharp, flexible, conducting, nonreactive tips for high-resolution imaging, oxidation lithography, and electrostatic force microscopy. By means of theory and experiments we lay out a map of several distinct tapping mode AFM oscillation states for CNT tipped AFM cantilevers: namely, noncontact attractive regime oscillation, intermittent contact with CNT slipping or pinning, or permanent contact with the CNT in point or line contact with the surface while the cantilever oscillates with large amplitude. Each state represents fundamentally different origins of CNT-surface interactions, CNT tip-substrate dissipation, and phase contrast …

Computational Model For Predicting Nonlinear Viscoelastic Damage Evolution In Materials Subjected To Dynamic Loading, Flavio V. Souza, Yong-Rak Kim, George A. Gazonas, David H. Allen

Department of Mechanical and Materials Engineering: Faculty Publications

Many inelastic solids accumulate numerous cracks before failure due to impact loading, thus rendering any exact solution of the IBVP untenable. It is therefore useful to construct computational models that can accurately predict the evolution of damage during actual impact/dynamic events in order to develop design tools for assessing performance characteristics. This paper presents a computational model for predicting the evolution of cracking in structures subjected to dynamic loading. Fracture is modeled via a nonlinear viscoelastic cohesive zone model. Two example problems are shown: one for model validation through comparison with a one-dimensional analytical solution for dynamic viscoelastic debonding, and …

Impacting Testing Of High Temperature Ceramics Through The Use Of A Vitiated Heater For Hot And Cold Fire Collisions, Adrian Trejo

Open Access Theses & Dissertations

Material testing is a crucial step during the design process as particular materials serve as safety and life saving conditions. In this study, a MoSi2 is chosen as the target specimen to undergo impact under high temperatures. An impact apparatus is designed and constructed for the purpose of propelling alumina particles at high velocities. A nozzle using compressed nitrogen gas is used to fire the particle at the desired velocities. Due to the possibility of thermal shock occurring at higher temperatures, a separate nozzle utilizing vitiation heating is designed to fire the particle at equally higher temperatures to prove the …

Effects Of Aggregate Structure On Hot-Mix Asphalt Rutting Performance In Low Traffic Volume Local Pavements, Yong-Rak Kim, Hee Mun Park, Francisco Thiago Sacramento Aragão, Jamilla Emi Sudo Lutif

Department of Mechanical and Materials Engineering: Faculty Publications

The objective of this study is to evaluate the effect of mix gradations associated with the Superpave restricted zone on rutting potential specifically for low traffic volume roadways. Although the elim-ination of the restricted zone requirement in Superpave mix design is highly recommended, some questions still remain unanswered as the research conclusions supporting the elimination of the re-stricted zone were largely made for medium to high traffic volume roadways, where aggregates are highly crushed and of good quality. The applicability of such research conclusions based on high traffic volume mixes needs to be verified for low volume mixes because many …

Convergence, Adaptive Refinement, And Scaling In 1d Peridynamics, Florin Bobaru Ph.D., Mijia Yabg Ph.D., Leonardo F. Alves M.S., Stewart A. Silling Ph.D., Ebrahim Askari Ph.D., Jifeng Xu Ph.D.

Department of Engineering Mechanics: Faculty Publications

We introduce here adaptive refinement algorithms for the non-local method peridynamics, which was proposed (in J. Mech. Phys. Solids 2000; 48:175–209) as a reformulation of classical elasticity for discontinuities and long-range forces. We use scaling of the micromodulus and horizon and discuss the particular features of adaptivity in peridynamics for which multiscale modeling and grid refinement are closely connected. We discuss three types of numerical convergence for peridynamics and obtain uniform convergence to the classical solutions of static and dynamic elasticity problems in 1D in the limit of the horizon going to zero. Continuous micromoduli lead to optimal rates of …

Comparison Of Fuzzy Clustering Methods And Their Applications To Geophysics Data, David J. Miller, Carl A. Nelson, Molly Boeka Cannon, Kenneth P. Cannon

Department of Mechanical and Materials Engineering: Faculty Publications

Fuzzy clustering algorithms are helpful when there exists a dataset with subgroupings of points having indistinct boundaries and overlap between the clusters. Traditional methods have been extensively studied and used on real-world data, but require users to have some knowledge of the outcome a priori in order to determine howmany clusters to look for. Additionally, iterative algorithms choose the optimal number of clusters based on one of several performance measures. In this study, the authors compare the performance of three algorithms (fuzzy c-means, Gustafson-Kessel, and an iterative version of Gustafson-Kessel) when clustering a traditional data set as well as real-world …

Experimental Investigation Of A Novel Blast Wave Mitigation Device, Zhenbi Su, Wen Peng, Zhaoyan Zhang, George Gogos, Reed Skaggs, Bryan Cheeseman, Chian Fong Yen

Department of Mechanical and Materials Engineering: Faculty Publications

A novel blast wave mitigation device was investigated experimentally in this paper. The device consists of a pistoncylinder assembly. A shock wave is induced within the cylinder when a blast wave impacts on the piston. The shock wave propagates inside the device and is reflected repeatedly. The shock wave propagation process inside the device lengthens the duration of the force on the base of the device to several orders of magnitude of the duration of the blast wave, while it decreases the maximum pressure over an order of magnitude. Two types of experiments were carried out to study the blast …

The Role Of Silicon Content On Environmental Degradations Of T91 Steels, Ajit K. Roy, D. Maitra, Pankaj Kumar

Mechanical Engineering Faculty Research

T91 grade steels showed a gradual enhancement in tensile ductility at ambient temperature due to an increase in Si content from 0.5 to 2.0 weight percent (wt.%). However, the ultimate tensile strength was reduced only above 1.5 wt.% Si. The corrosion potential became more active in an acidic solution with increasing temperature. The cracking susceptibility in a similar environment under a slow-strain-rate (SSR) condition was enhanced at higher temperatures showing reduced ductility, time to failure, and true failure stress. Cathodic potentials applied to the test specimens in SSR testing caused an enhanced cracking tendency at 30 and 60°C, suggesting hydrogen …

Tensile Deformation Of A Nickel-Base Alloy At Elevated Temperatures, Ajit K. Roy, Anand Venkatesh, Vikram Marthandam

Mechanical Engineering Faculty Research

The results of tensile testing involving Waspaloy indicate that the failure strain was gradually reduced at temperatures ranging between ambient and 300 °C. Further, serrations were observed in the engineering stress versus strain diagrams in the temperature range of 300-600 °C. The reduced failure strain and the formation of serrations in these temperature regimes could be the result of dynamic strain aging of this alloy. The extent of work hardening due to plastic deformation was reduced at temperatures above 300 °C. A combination of ductile and intergranular brittle failures was seen at temperatures above 600 °C. γ′ was detected at …

Stereolithography Of Poly(Ethylene Glycol) Hydrogels With Application In Tissue Engineering As Peripheral Nerve Regeneration Scaffolds, Karina Arcaute

Open Access Theses & Dissertations

In recent years, rapid prototyping (RP) technologies initially developed to create prototypes prior to production for the automotive, aerospace, and other industries, have found applications in tissue engineering (TE). Several different RP technologies are being used to fabricate biocompatible 3D structures with controlled micro- and macro-scale characteristics. The focus of this research was to explore the capabilities of the RP technology, stereolithography (SL), for creating complex, 3D scaffolds with applications in TE using a photocrosslinkable biopolymer, poly(ethylene glycol) (PEG). The primary objective was to create an implantable multi-lumen nerve guidance conduit (NGC) for the regeneration of peripheral nerves.

Studies of …

Control Of The Nanoscale Crystallinity And Phase Separation In Polymer Solar Cells, Chih-Wei Chu, Hoichang Yang, Wei-Jen Hou, Jinsong Huang, Gang Li, Yang Yang

Department of Mechanical and Materials Engineering: Faculty Publications

Grazing-incidence x-ray diffraction and atomic force microscopy were performed on bulk heterojunction regioregular poly(3-hexylthiophene) (RR-P3HT) [6,6]-phenyl-C₇₁-butyric acid methyl esters spin-cast films with different film processing conditions to correlate the crystalline nanostructure of P3HT with the corresponding solar cell performance. The increase in long wavelength absorption for solvent annealed films is related to highly conjugated crystal structure of RR-P3HT phase-separated in the active layer. Upon thermal annealing, the solvent annealed 50-nm-thick device shows high solar cell performance with fill factor up to 73% and power conversion efficiency of 3.80%.

Modelagem Da Vida De Fadiga E Do Acúmulo De Deformações Permanentes Em Pavimentos Asfálticos Por Meio De Um Modelo De Dano Contínuo, Victor Ferreira Teixeira, Flavio V. Souza, Jorge Barbosa Soares

Department of Mechanical and Materials Engineering: Faculty Publications

: It is known that the conditions of the Brazilian roadways have an enormous impact over the national economy. In face of this problem, there is a need for new methodologies for pavement analyses and design that can more accurately predict pavement distresses. Among the main methods currently used, one can find purely empirical methods and mechanistic-empirical methods which make use of the pavement structure response. The evolution of numerical methods such as the Finite Element Method (FEM) or the Boundary Element Method (BEM) has made the mechanistic-empirical methods more popular for pavement analysis applications. This work shows a mechanistic …

Improved Hole-Injection Contact For Top-Emitting Polymeric Diodes, Juo-Hao Li, Jinsong Huang, Yang Yang

Department of Mechanical and Materials Engineering: Faculty Publications

In this letter, an efficient hole-injection contact was achieved for the top-emitting polymeric light-emitting diodes (PLEDs). The anode has a structure of metal/molybdenum oxide/ poly(3,4-ethylenedioxythiophene) poly(styrenesulfonate) (PEDOT:PSS). It has been found that hole injection was significantly improved by inserting a thin layer of MoO₃ between aluminum and PEDOT:PSS. An ultraviolet photoelectron spectroscopy (UPS) was used to investigate the change of work function, and photovoltaic measurement confirmed that the improved hole injection is due to the reduction of barrier height, resulted from the addition of transition metal oxide. PEDOT:PSS layer was found necessary in anode structure to further enhance the …

Influence Of Van Der Waals Forces On Increasing The Strength And Toughness In Dynamic Fracture Of Nanofibre Networks: A Peridynamic Approach, Florin Bobaru Ph.D.

Department of Engineering Mechanics: Faculty Publications

The peridynamic method is used here to analyse the effect of van der Waals forces on the mechanical behaviour and strength and toughness properties of three-dimensional nanofibre networks under imposed stretch deformation. The peridynamic formulation allows for a natural inclusion of long-range forces (such as van der Waals forces) by considering all interactions as ‘long-range’. We use van der Waals interactions only between different fibres and do not need to model individual atoms. Fracture is introduced at the microstructural (peridynamic bond) level for the microelastic type bonds, while van der Waals bonds can reform at any time. We conduct statistical …

Low Voltage And Fast Speed All-Polymeric Optocouplers, Yan Yao, Hsiang-Yu Chen, Jinsong Huang, Yang Yang

Department of Mechanical and Materials Engineering: Faculty Publications

An all-polymeric optocoupler has been demonstrated with a polymer light-emitting diode (PLED) as the light source (input unit) and a polymer/fullerene photodiode (PD) as the detector (output unit). The electroluminescence (EL) peak of the PLED is 560 nm, and the entire EL spectrum is within the response range of the PD. The optocoupler can work at low driving voltages, 5 V on the PLED and 0 V on the PD. The output photocurrent increases linearly with input current, and the current density transfer ratio reaches 1.5%. The frequency response of the optocoupler is at 500 kHz. With comparable performance to …

Origin Of Photomultiplication In C60 Based Devices, Jinsong Huang, Yang Yang

Department of Mechanical and Materials Engineering: Faculty Publications

In this manuscript, the origin of the photomultiplication effect was studied in C₆₀ based devices by evaluating the wavelength dependent external and internal quantum efficiencies under various biases. The effect of materials with disordered structures on the photomultiplication effect was determined by intentionally integrating both ordered and disordered material structures into one organic solar cell device with a configuration of indium tin oxide/poly(3,4-ethylenedioxythiophene) poly(styrenesulfonate) (PEDOT:PSS)/pentacene/C₆₀ fullerene/bathocuproine (BCP)/Al. Our results show that both the disordered structure of C₆₀ and the charge trapping effect at the C₆₀ /PEDOT:PSS interface contribute to the photomultiplication effect. By studying the C60-only …

Deck-Mounted Steel Post Barrier System, John D. Reid, Ronald K. Faller, Jason A. Hascall

Department of Mechanical and Materials Engineering: Faculty Publications

An existing mountable safety barrier system, previously crash tested successfully on a wood bridge deck, was evaluated for use on a fiber reinforced plastic (FRP) bridge deck. In an attempt to avoid expensive full-scale crash testing, components of the existing system were evaluated using worst case conditions on two dynamic bogie crash tests and a series of computer simulations using nonlinear finite-element analysis. Simulation results closely approximated the physical results, with both displaying similar deformation, damage, and force levels. Both testing and simulation demonstrated that the barrier should function sufficiently if used on the FRP deck system. Further, the development …

Regional Mechanical Properties And Stress Analysis Of The Human Anterior Lens Capsule, Ryan M. Pedrigi, G. David, J. Dziezyc, J. D. Humphrey

Department of Mechanical and Materials Engineering: Faculty Publications

The lens capsule of the eye functions, in part, as a deformable support through which the ciliary body applies tractions that can alter lens curvature and corresponding refractive power during the process of accommodation. Although it has long been recognized that characterization of the mechanical properties of the lens capsule is fundamental to understanding this physiologic process as well as clinical interventions, prior data have been limited by one-dimensional testing of excised specimens despite the existence of multiaxial loading in vivo. In this paper, we employ a novel experimental approach to study in situ the regional, multiaxial mechanical behavior of …