Mechanical Engineering Commons^™

Process Study And Control Of Electron Beam Melting Technology Using Infrared Thermography, Jorge Mireles

Open Access Theses & Dissertations

An IR camera was installed in an Arcam A2 system (Arcam AB, Mölndal, Sweeden) and layer-by-layer image acquisition was achieved. The camera's capability to detect manufacturing defects was evaluated by implementing computer vision techniques using LabVIEW measurement and programming software (National Instruments, Austin, TX). Thermal maps acquired by the IR camera allowed layer-by-layer part temperature to be recorded. A core objective of this research was to study the impact of processing temperature on EBM-fabricated Ti-6Al-4V parts and achieve controlled mechanical properties. In this research, build variations were achieved by modifying parameters that change processing temperature from the standard processing temperature. …

Experimental Study On The Fabrication Of Advanced Materials For Energy Applications Using High Energy Mechanical Milling, Ashvin Kumar Narayana Swamy

Open Access Theses & Dissertations

The reaction of aluminum (Al) powder with water has the potential for on demand hydrogen generation. Conventional Al powders, however, react with water slowly due to a highly protective oxide layer on the particle surface. Current methods for Al activation involve harmful and expensive materials. The nano-scale Al powders also remain very expensive and have problems such as a large amount of oxide on the surface. The use of aluminum in an energy generation cycle is also hindered by the fact that, although Al is the most abundant metal in the Earth's crust, its recovery from ore consumes a lot …

Effect Of Hafnium-Incorporation On The Microstructure And Dielectric Properties Of Cobalt Ferrite Ceramics, Stephen Josiah Wells

Open Access Theses & Dissertations

The effect of hafnium ion (Hf⁴⁺) incorporation in cobalt ferrite (CFO) was studied. Samples of Hf substituted CFO ceramic (CoFe_2-xHf_xO₄), were synthesized in the laboratory with hafnium concentrations ranging from x=0.000 to x=0.200. X-ray diffraction scans show that the Hafnium CFO crystalizes in the inverse spinel phase. Inclusion of hafnium causes lattice expansion, increasing the lattice parameter from 8.374 í? for pure CoFe2O4 to 8.391 í? for the highest concentration of hafnium tested (x=0.020). The dielectric properties of CFO are greatly enhanced by inclusion of hafnium. The enhancement is due to the …

Thermal Barrier Coatings (Tbc's) For High Heat Flux Thrust Chambers, Christopher Michael Bradley

Open Access Theses & Dissertations

The last 30 years materials engineers have been under continual pressure to develop materials with a greater temperature potential or to produce configurations that can be effectively cooled or otherwise protected at elevated temperature conditions. Turbines and thrust chambers produce some of the harshest service conditions for materials which lead to the challenges engineers face in order to increase the efficiencies of current technologies due to the energy crisis that the world is facing. The key tasks for the future of gas turbines are to increase overall efficiencies to meet energy demands of a growing world population and reduce the …

New Topics On Nanoindentation Of Polymers And Composite Materials, Ricardo Martinez-Hernandez

Open Access Theses & Dissertations

In this study, nanoindentation was used to determine Young's modulus of homogeneous plastic materials as well as inhomogeneous epoxy woven fabric composites using various indenters. In the first part, homogeneous PMMA and polycarbonate were characterized using conical and spherical indenters. The conventional approach of the inverse analysis was modified in order to account for effects obtained during spherical nanoindentation. The experimental results were verified using FEA analysis in ABAQUS. It was found that viscous effects were present in conical nanoindentations which led to an overestimation of contact stiffness. The second part, the response of carbon and glass fiber woven fabric …

Solution-Processed Nanoparticle Super-Float-Gated Organic Field-Effect Transistor As Un-Cooled Ultraviolet And Infrared Photon Counter, Yongbo Yuan, Qingfeng Dong, Bin Yang, Fawen Guo, Qi Zhang, Ming Han, Jinsong Huang

Department of Mechanical and Materials Engineering: Faculty Publications

High sensitivity photodetectors in ultraviolet (UV) and infrared (IR) range have broad civilian and military applications. Here we report on an un-cooled solution-processed UV-IR photon counter based on modified organic field-effect transistors. This type of UV detectors have light absorbing zinc oxide nanoparticles (NPs) sandwiched between two gate dielectric layers as a floating gate. The photon-generated charges on the floating gate cause high resistance regions in the transistor channel and tune the source-drain output current. This ‘‘super-float-gating’’ mechanism enables very high sensitivity photodetectors with a minimum detectable ultraviolet light intensity of 2.6 photons/µm²s at room temperature as well …

Analysis Of Electrically-Forced Vibrations Of Piezoelectric Mesa Resonators, Huijing He, Guo-Quan Nie, Jin-Xi Liu, Jiashi Yang

Department of Mechanical and Materials Engineering: Faculty Publications

We study the electrically forced thickness-shear and thickness-twist vibrations of stepped thickness piezoelectric plate mesa resonators made of polarized ceramics or 6-mm class crystals. A theoretical analysis based on the theory of piezoelectricity is performed, and an analytical solution is obtained using the trigonometric series. The electrical admittance, resonant frequencies, and mode shapes are calculated, and strong energy trapping of the modes is observed. Their dependence on the geometric parameters of the resonator is also examined.

Review Of Electrochemical And Electrodischarge Machining, Kamlakar P. Rajurkar, M. M. Sundaram, A. P. Malshe

Department of Mechanical and Materials Engineering: Faculty Publications

Electrochemical and electro-discharge machining processes are the two major electro-machining processes with unique capabilities. Electrical Discharge Machining (EDM) and Electrochemical Machining (ECM) offer a better alternative or sometimes the only alternative in generating accurate 3-D complex shaped macro, micro and nano features and components of difficult–to-machine materials. Technological advances reported in electrochemical and electro discharge machining processes, which reflect the state of the art in academic and industrial research and applications, are briefly reviewed in this paper.

Wire Electro-Discharge Machining Of Titanium Alloy, Farnaz Nourbakhsh, Kamlakar P. Rajurkar, Ajay P. Malshe, Jian Cao

Department of Mechanical and Materials Engineering: Faculty Publications

This paper presents an experimental investigation of wire electro-discharge machining (WEDM) of titanium alloy. The objective is to investigate the effect of seven process parameters including pulse width, servo reference voltage, pulse current, and wire tension on process performance parameters (such as cutting speed, wire rupture and surface integrity). A Taguchi L18 design of experiment (DOE) has been applied. All experiments have been conducted using Charmilles WEDM. It was also found that the cutting speed increases with peak current and pulse interval. Surface roughness was found to increase with pulse width and decrease with pulse interval. The Analysis of Variance …

Selective Detection And Automated Counting Of Fluorescently-Labeled Chrysotile Asbestos Using A Dual-Mode High-Throughput Microscopy (Dm-Htm) Method, Myoung-Ock Cho, Hyo Mi Chang, Donghee Lee, Yeon Gyu Yu, Hwataik Han, Jung Kyung Kim

Department of Mechanical and Materials Engineering: Faculty Publications

Phase contrast microscopy (PCM) is a widely used analytical method for airborne asbestos, but it is unable to distinguish asbestos from non-asbestos fibers and requires time-consuming and laborious manual counting of fibers. Previously, we developed a high-throughput microscopy (HTM) method that could greatly reduce human intervention and analysis time through automated image acquisition and counting of fibers. In this study, we designed a dual-mode HTM (DM-HTM) device for the combined reflection and fluorescence imaging of asbestos, and automated a series of built-in image processing commands of ImageJ software to test its capabilities. We used DksA, a chrysotile-adhesive protein, for selective …

Photovoltaic Device, Jinsong Huang, Bin Yang, Yongbo Yuan

Department of Mechanical and Materials Engineering: Faculty Publications

An apparatus includes a substrate; and a photoactive layer disposed on the substrate. The photoactive layer includes an electron acceptor material; an electron donor material; and a material having dipoles.

Energy Trapping Of Thickness-Shear And Thickness-Twist Modes In A Partially Electroded At-Cut Quartz Resonator, Huijing He, Guoquan Nie, Jinxi Liu, Jiashi Yang

Department of Mechanical and Materials Engineering: Faculty Publications

The thickness-shear and thickness-twist vibrations of a finite and partially electroded AT-cut quartz resonator are investigated. The equations of anisotropic elasticity are used with the omission of the small elastic constant c56 . An analytical solution is obtained using Fourier series from which the free vibration resonant frequencies, mode shapes, and energy trapping are calculated and examined.

Implementation Of Magnetic Resonance Elastography For The Investigation Of Traumatic Brain Injuries, Thomas Boulet

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Magnetic resonance elastography (MRE) is a potentially transformative imaging modality allowing local and non-invasive measurement of biological tissue mechanical properties. It uses a specific phase contrast MR pulse sequence to measure induced vibratory motion in soft material, from which material properties can be estimated. Compared to other imaging techniques, MRE is able to detect tissue pathology at early stages by quantifying the changes in tissue stiffness associated with diseases. In an effort to develop the technique and improve its capabilities, two inversion algorithms were written to evaluate viscoelastic properties from the measured displacements fields. The first one was based on …

Maximal Force Characteristics Of The Ca2+-Powered Actuator Of Vorticella Convallaria, Sangjin Ryu, Matthew J. Lang, Paul Matsudaira

Department of Mechanical and Materials Engineering: Faculty Publications

The millisecond stalk contraction of the sessile ciliate Vorticella convallaria is powered by energy from Ca²⁺ binding to generate contractile forces of ~10 nN. Its contractile organelle, the spasmoneme, generates higher contractile force under increased stall resistances. By applying viscous drag force to contracting V. convallaria in a microfluidic channel, we observed that the mechanical force and work of the spasmoneme depended on the stalk length, i.e., the maximum tension (150–350 nN) and work linearly depended on the stalk length (~2.5 nN and ~30 fJ per 1 mm of the stalk). This stalk-length dependency suggests that motor units of …

Shear-Horizontal Vibration Modes Of An Oblate Elliptical Cylinder And Energy Trapping In Contoured Acoustic Wave Resonators, Huijing He, Jiashi Yang, John A. Kosinski

Department of Mechanical and Materials Engineering: Faculty Publications

We study shear-horizontal free vibrations of an elastic cylinder with an oblate elliptical cross section and a traction-free surface. Exact vibration modes and frequencies are obtained. The results show the existence of thickness-shear and thickness-twist modes. The energy-trapping behavior of these modes is examined. Trapped modes are found wherein the vibration energy is largely confined to the central portion of the cross section and little vibration energy is found at the edges. It is also shown that face-shear modes are not allowed in such a cylinder. The results are useful for the understanding of the energy trapping phenomenon in contoured …

Propagation Of Ultrasound Through Freshly Excised Human Calvarium, Armando Garcia Noguera

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

The propagation of ultrasound through complex biological media, such as the human calvarium, poses a great challenge for modern medicine. Several ultrasonic techniques commonly used for treatment and diagnosis in most of the human body are still difficult to apply to the human brain, in part, because of the properties of the skull. Moreover, an understanding of the biomechanics of transcranial ultrasound may provide needed insight into the problem of blast wave induced traumatic brain injury (TBI). In the present study, the spatial variability of ultrasonic properties was evaluated for relevant frequencies of 0.5, 1, and 2.25 MHz. A total …

Nonlinear Mechanical Behavior Of The Human Common, External And Internal Carotid Arteries In Vivo, Alexey Kamenskiy, Yuris A. Dzenis, Jason N. Mactaggart, Thomas G. Lynch, Syed A. Jaffar Kazmi, Iraklis I. Pipinos

Department of Mechanical and Materials Engineering: Faculty Publications

Introduction—The mechanical environment and properties of the carotid artery play an important role in the formation and progression of atherosclerosis in the carotid bifurcation. The purpose of this work was to measure and compare the range and variation of circumferential stress and tangent elastic moduli in the human common (CCA), external (ECA) and internal (ICA) carotid arteries over the cardiac cycle in vivo.

Methods—Measurements were performed in the surgically exposed proximal cervical CCA, distal ECA and distal ICA of normotensive patients (n = 16) undergoing carotid endarterectomy. All measurements were completed in vivo over the cardiac cycle …

Three-Dimensional Geometry Of The Human Carotid Artery, Alexey Kamenskiy, Jason N. Mactaggart, Iraklis I. Pipinos, Jai Bikhchandani, Yuris A. Dzenis

Department of Mechanical and Materials Engineering: Faculty Publications

Accurate characterization of carotid artery geometry is vital to our understanding of the pathogenesis of atherosclerosis. Three-dimensional computer reconstructions based on medical imaging are now ubiquitous; however, mean carotid artery geometry has not yet been comprehensively characterized. The goal of this work was to build and study such geometry based on data from 16 male patients with severe carotid artery disease. Results of computerized tomography angiography were used to analyze the cross-sectional images implementing a semiautomated segmentation algorithm. Extracted data were used to reconstruct the mean three-dimensional geometry and to determine average values and variability of bifurcation and planarity angles, …

Development And Validation Of A Model For Granular Material Volume Measurements, Pourya Fasounaki

Department of Industrial and Management Systems Engineering: Dissertations, Theses, and Student Research

Keeping inventory record of packed grains in silos poses challenges since the bulk material’s different segments do not discharge uniformly, leading to formation of random peaks and valleys on the surface. To facilitate obtaining accurate volume measurement of the grains by taking into account this non-linear behavior on the surface, laser or plumb-bob level-sensing devices are employed at different part of the surface to probe the level of material under those regions.

The main goals of this research is to study the behavior of granular material in silo while discharging downward and by doing so, differentiate certain flow patterns formed …

Rehabilitation And Exercise Machine, Judith M. Burnfield, Yu Shu, Thad W. Buster, Carl Nelson

Department of Mechanical and Materials Engineering: Faculty Publications

An improved rehabilitation and exercise machine is provided which allows a person with physical limitations, disabilities or chronic conditions to use the machine in order to rehabilitate their muscles, improve joint flexibility, and enhance cardiovascular fitness.

Shock And Vibration Isolation System For Ambulatory And Litter Patients In Ground And Air Medical Transport, Mohamad R. Hachem

UNLV Theses, Dissertations, Professional Papers, and Capstones

This project explored the effectiveness of seat and litter air bladder technologies in reducing patient exposure to whole body shock and vibration during ground borne and airborne medical transport. Several seat and litter air bladder configurations were examined during field tests in a U.S. Army RG-33 MRAP ambulance and a U.S. Army HH-60M Black Hawk helicopter. The MRAP field tests were conducted at Ft. Detrick, Maryland. The Black Hawk field tests were conducted at Ft. Rucker, Alabama.

During the field tests, tri-axial vibration signals were recorded on a 16-channel CoCo90 Data Logger/Frequency Analyzer and then post processed in the laboratory …

Numerical Modeling Of High Temperature Bayonet Heat Exchanger And Decomposer For Decomposition Of Sulfur Trioxide, Vijaisri Nagarajan, Yitung Chen, Tzu-Chen Hung, Qiuwang Wang, Valery Ponyavin

College of Engineering: Graduate Celebration Programs

Motivation

• Hydrogen is an attractive energy carrier in the future energy technology.

• Hydrogen is produced from splitting of water through various process namely electrolysis, photo-electrolysis, photo-biological production and thermochemical water-splitting.

• The aim of this study is to numerically investigate fluid flow, heat transfer and chemical reaction in bayonet high temperature heat exchanger and decomposer.

• Parametric studies are performed to achieve maximum decomposition with less pressure drop.

Model-Based Systems And Methods For Analyzing And Predicting Outcomes Of Vascular Interventions And Reconstructions, Yuris A. Dzenis, Alexey Kamenskiy, Iraklis I. Pipinos, Jason N. Mactaggart

Department of Mechanical and Materials Engineering: Faculty Publications

Systems and methods for analyzing and predicting treatment outcomes of medical procedures such as vascular interventions and reconstructions are disclosed. An illustrative system for analyzing and predicting therapeutic outcomes of medical procedures comprises a relational database configured for classifying and storing patient specific input data for multiple patients, a fluid-solid interaction biomechanical model configured for performing a biomechanics simulation and generating biomechanics data, and a graphical user interface.

Effects Of Mismatched Electrodes On An At-Cut Quartz Resonator, Huijing He, Jinxi Liu, Jiashi Yang

Department of Mechanical and Materials Engineering: Faculty Publications

We study thickness-shear and thickness-twist free vibrations of a finite AT-cut quartz resonator with mismatched electrodes. The equations of anisotropic elasticity are used with the omission of the small elastic constant c56. An analytical solution is obtained using Fourier series from which the resonant frequencies, mode shapes, and vibration confinement resulting from the electrode inertia are calculated and examined.

Method For Increasing The Efficiency Of Organic Photovoltaic Cells, Jinsong Huang, Yongbo Yuan

Department of Mechanical and Materials Engineering: Faculty Publications

The present invention is directed to an organic photovoltaic cell that contains one or more dipole regions generally disposed between an organic active region and the electrodes and a process for producing such an organic photovoltaic cell.

Macro And Microfluidic Flows For Skeletal Regenerative Medicine, Brandon D. Riehl, Jung Yul Lim

Department of Mechanical and Materials Engineering: Faculty Publications

Fluid flow has a great potential as a cell stimulatory tool for skeletal regenerative medicine, because fluid flow-induced bone cell mechanotransduction in vivo plays a critical role in maintaining healthy bone homeostasis. Applications of fluid flow for skeletal regenerative medicine are reviewed at macro and microscale. Macroflow in two dimensions (2D), in which flow velocity varies along the normal direction to the flow, has explored molecular mechanisms of bone forming cell mechanotransduction responsible for flow-regulated differentiation, mineralized matrix deposition, and stem cell osteogenesis. Though 2D flow set-ups are useful for mechanistic studies due to easiness in in situ and post-flow …

Development Of A Multi-Material, Multi-Technology Fdm System For Process Improvement Experimentation, David Espalin

Open Access Theses & Dissertations

Over the last three decades, developments within the area of Additive Manufacturing (AM) have resulted in novel technologies capable of producing highly customized, complex part geometries in a fraction of the lead time required by traditional manufacturing methods (e.g., injection molding, metal casting). In particular, fused deposition modeling (FDM), a material extrusion AM process, can produce parts using production-grade thermoplastics like acrylonitrile butadiene styrene, polycarbonate, and polyetherimide. Additionally, non-commercial materials (e.g., polycaprolactone, ceramic loaded polymers, carbon nanotube loaded polymers) have been processed using FDM in part to demonstrate the potential diversity in material selection.

Recently, a myriad of personal 3D …

Oxidation Of Borides And Carbides With Y2o3 And Ta Additions, Salvador Manuel Rodriguez

Open Access Theses & Dissertations

The study presented here describes an investigation of an oxidation scale of a fully-sintered Y2O3-ZrB2-TiC composite exposed in air at 1173K. Upon oxidation of the boride/carbide, a ZrO2-TiO2 was expected to form similar to the ZrO2-SiO2 dual scale of an oxidized ZrB2-SiC. The 47wt% Y2O3-38wt%ZrB2-16wt%TiC composite formed a dual scale consisting primarily of an Y2O3-ZrO2-TiC inner scale with an outer scale of ZrO2-TiO2-Y2O3.

The samples oxidized with a parabolic layer growth allowing the calculation of the effective diffusion coefficient indicating that the oxidation was controlled by oxygen ingress through primarily the ZrO2-Y2O3 phase. The oxygen potential between the inner layer …

Sacrificial Structure Preforms For Thin Part Machining, Scott Smith, Robert Wilhelm, Brian Dutterer, Harish Cherukuri, Gaurav Goel

Department of Mechanical and Materials Engineering: Faculty Publications

Thin parts are often difficult to create by machining because they have insufficient static and dynamic stiffness. Accurate thin parts are difficult to achieve due to clamping forces, cutting forces, residual stresses, and chatter. Sacrificial structure preforms support the part during machining, but they are not part of the finished component. Preforms may be created in many ways, including forging, welding, gluing, casting, or additive processes. They can be used in many workpiece materials including metals, polymers, and ceramics. We describe a novel process that uses sacrificial structures to make machining insensitive to the thinness of finished parts.

Moisture Damage Characterization Of Warm-Mix Asphalt Mixtures Based On Laboratory-Field Evaluation, Yong-Rak Kim, Jun Zhang, Hoki Ban

Department of Mechanical and Materials Engineering: Faculty Publications

This study presents laboratory evaluation integrated with field performance to examine two widely used warm-mix asphalt (WMA) approaches—foaming and emulsion technology. For a more realistic evaluation of the WMA approaches, trial pavement sections of the WMA mixtures and their counterpart hot-mix asphalt (HMA) mixtures were implemented in Antelope County, Nebraska. Field-mixed loose mixtures collected at the time of paving were transported to the laboratories to conduct various experimental evaluations of the individual mixtures. Among the laboratory tests, three (two conventional and one newly attempted) were performed to characterize moisture damage potential which is the primary focus of this study. From …