Mechanical Engineering Commons^™

Stabilized Wide Bandgap MapbbrXI3– X Perovskite By Enhanced Grain Size And Improved Crystallinity, Miao Hu, Cheng Bi, Yongbo Yuan, Yang Bai, Jinsong Huang

Department of Mechanical and Materials Engineering: Faculty Publications

Methylammonium lead trihalide perovskite (MAPbX₃, where MA is methylammonium, and X is a halide)-based solar cells have been intensively investigated recently, with the demonstrated certified solar power conversion efficiency (PCE) exceeding 20%. To further boost the PCE to beyond the Schockley–Queisser limit, tandem structured solar cells have been investigated based on integrating MAPbX₃ and low bandgap solar cells. However, the efficiency of the two-terminal integrated perovskite-silicon tandem cells is still low. The best reported efficiency of 13.7% for this type of tandem cells is far smaller than the individual cells yet, partially due to the limited performance …

Ultrahigh Sensitivity Of Methylammonium Lead Tribromide Perovskite Single Crystals To Environmental Gases, Hong-Hua Fang, Sampson Adjokatse, Haotong Wei, Jie Yang, Graeme R. Blake, Jinsong Huang, Jacky Even, Maria Antonietta Loi

Department of Mechanical and Materials Engineering: Faculty Publications

One of the limiting factors to high device performance in photovoltaics is the presence of surface traps. Hence, the understanding and control of carrier recombination at the surface of organic-inorganic hybrid perovskite is critical for the design and optimization of devices with this material as the active layer. We demonstrate that the surface recombination rate (or surface trap state density) inmethylammonium lead tribromide (MAPbBr3) single crystals can be fully and reversibly controlled by the physisorption of oxygen and water molecules, leading to a modulation of the photoluminescence intensity by over two orders of magnitude.We report an unusually low surface recombination …

Pulsed Laser Cutting Of Magnesium-Calcium For Biodegradable Stents, M. P. Sealy, Y. B. Guo, J. F. Liu, C. Li

Department of Mechanical and Materials Engineering: Faculty Publications

There is growing interests in the use of biodegradable magnesium implants for cardiovascular and pulmonary applications such as stents. Magnesium is a metal that has the ability to gradually dissolve and absorb into the human body after implantation. There is very little work discussing the relationship between process parameters and cut quality of magnesium stents by laser cutting. The objective of this research is to determine the effect of laser cutting conditions including peak laser power and cutting speed of a millisecond range pulsed laser on kerf geometry, surface topography, surface roughness, and microstructure. An assessment on the experimental work …

Impact Of Patient Factors On Operative Duration During Laparoscopic Cholecystectomy: Evaluation From The National Surgical Quality Improvement Program Database, Bethany Rose Lowndes, Cornelius A. Thiels, Elizabeth B. Habermann, Juliane Bingener, M. Susan Hallbeck, Denny Yu

Department of Mechanical and Materials Engineering: Faculty Publications

BACKGROUND: Patient factors impact laparoscopic cholecystectomy (LC) difficulty, specifically operative duration. This study quantifies the impact of patient factors on LC duration.

METHODS: The national surgery database (American College of Surgeons National Surgical Quality Improvement Program) was reviewed for all elective LC for biliary colic from 2005 to 2013. Multivariate general linear model and logistic regression were used to evaluate patient factors as predictors of operative duration greater than 60 minutes, adjusted for resident involvement and cholangiography.

RESULTS: A total of 24,099 LC met inclusion criteria. Regression analysis found procedure duration greater than 60 minutes was less likely for patients …

A Comparative Study On Machining Capabilities Of Wet And Dry Nanoscale Electro-Machining, Muhammad P. Jahan, Kamlakar P. Rajurkar, Ajay P. Malshe

Department of Mechanical and Materials Engineering: Faculty Publications

Presently, the nano scale electro-machining (nano-EM) process has been demonstrated in both the liquid and air dielectric mediums, which are known as wet and dry nano-EM respectively. In the current study, two important aspects of the nano-EM have been investigated: the minimum possible feature dimension and mass fabrication capability of nano-EM. Firstly, the investigation has been done on the capability of machining graphene at atomic scale with focus on obtaining smallest possible nano-feature using the wet nano-EM. Secondly, the ability of the nano-EM process for the fabrication of arrays of nano-holes has been investigated using dry nano-EM. It was found …

Bioink Properties Before, During And After 3d Bioprinting, Katja Holzl, Shengmao Lin, Liesbeth Tytgat, Sandra Van Vlierberghe, Linxia Gu, Aleksandr Ovsianikov

Department of Mechanical and Materials Engineering: Faculty Publications

Bioprinting is a process based on additive manufacturing from materials containing living cells. These materials, often referred to as bioink, are based on cytocompatible hydrogel precursor formulations, which gel in a manner compatible with different bioprinting approaches. The bioink properties before, during and after gelation are essential for its printability, comprising such features as achievable structural resolution, shape fidelity and cell survival. However, it is the final properties of the matured bioprinted tissue construct that are crucial for the end application. During tissue formation these properties are influenced by the amount of cells present in the construct, their proliferation, migration …

Development Of A Synthetic Gene Network To Modulate Gene Expression By Mechanical Forces, Zoltan Kis, Tania Rodin, Asma Zafar, Zhangxing Lai, Grace Freke, Oliver Fleck, Armando Del Rio Hernandez, Leila Towhidi, Ryan M. Pedrigi, Takayuki Homma, Rob Krams

Department of Mechanical and Materials Engineering: Faculty Publications

The majority of (mammalian) cells in our body are sensitive to mechanical forces, but little work has been done to develop assays to monitor mechanosensor activity. Furthermore, it is currently impossible to use mechanosensor activity to drive gene expression. To address these needs, we developed the first mammalian mechanosensitive synthetic gene network to monitor endothelial cell shear stress levels and directly modulate expression of an atheroprotective transcription factor by shear stress. The technique is highly modular, easily scalable and allows graded control of gene expression by mechanical stimuli in hard-to-transfect mammalian cells. We call this new approach mechanosyngenetics. To insert …

Portable Camera Aided Simulator (Portcas) For Minimally Invasive Surgical Training, Ka-Chun Sui, Carl Nelson, Mohsen Zahiri, Dmitry Oleynikov

Department of Mechanical and Materials Engineering: Faculty Publications

The present disclosure is directed to a system and method for surgical training with low cost, reusable materials and a highly customizable virtual environment for skill-building. According to various embodiments, a surgical training tool is usable in conjunction with a support structure configured to at least partially constrain the tool movement. Meanwhile, the tool is tracked in real-time with off-tool detectors to generate a tool path driving a virtual rendering of the surgical training tool in an operative environment. The virtual rendering may be visually observable via a display device and may include a customizable and/or selectable operative environment with …

Secondary Pool Boiling Effects, C. Kruse, A. Tsubaki, C. A. Zuhlke, T. P. Anderson, Dennis R. Alexander, George Gogos, Sidy Ndao

Department of Mechanical and Materials Engineering: Faculty Publications

A pool boiling phenomenon referred to as secondary boiling effects is discussed. Based on the experimental trends, a mechanism is proposed that identifies the parameters that lead to this phenomenon. Secondary boiling effects refer to a distinct decrease in the wall superheat temperature near the critical heat flux due to a significant increase in the heat transfer coefficient. Recent pool boiling heat transfer experiments using femtosecond laser processed Inconel, stainless steel, and copper multiscale surfaces consistently displayed secondary boiling effects, which were found to be a result of both temperature drop along the microstructures and nucleation characteristic length scales. The …

Experimental Explanation Of The Formation Mechanism Of Surface Mound-Structures By Femtosecond Laser On Polycrystalline Ni60Nb40, Edwin Peng, A. Tsubaki, Craig A. Zuhlke, Meiyu Wang, Ryan Bell, Michael J. Lucis, Troy P. Anderson, Dennis R. Alexander, George Gogos, Jeffrey E. Shield

Department of Mechanical and Materials Engineering: Faculty Publications

Femtosecond laser surface processing (FLSP) is an emerging technique for creating functionalized surfaces with specialized properties, such as broadband optical absorption or superhydrophobicity/ superhydrophilicity. It has been demonstrated in the past that FLSP can be used to form two distinct classes of mound-like, self-organized micro/nanostructures on the surfaces of various metals. Here, the formation mechanisms of below surface growth (BSG) and above surface growth (ASG) mounds on polycrystalline Ni₆₀Nb₄₀ are studied. Cross-sectional imaging of these mounds by focused ion beam milling and subsequent scanning electron microscopy revealed evidence of the unique formation processes for each class of …

Process Development For Compression Molding Of Hybrid Continuous And Chopped Carbon Fiber Prepreg For Production Of Functionally Graded Composite Structures, Corinne Marie Warnock

Master's Theses

Composite materials offer a high strength-to-weight ratio and directional load bearing capabilities. Compression molding of composite materials yields a superior surface finish and good dimensional stability between component lots with faster processing compared to traditional manufacturing methods. This experimental compression molding capability was developed for the ME composites lab using unidirectional carbon fiber prepreg composites. A direct comparison was drawn between autoclave and compression molding methods to validate compression molding as an alternative manufacturing method in that lab. A method of manufacturing chopped fiber from existing unidirectional prepreg materials was developed and evaluated using destructive testing methods. The results from …

Imaging Thermal Conductivity With Nanoscale Resolution Using A Scanning Spin Probe, Abdelghani Laraoui, Halley Aycock-Rizzo, Yang Gao, Xi Lu, Elisa Riedo, Carlos A. Meriles

Department of Mechanical and Materials Engineering: Faculty Publications

The ability to probe nanoscale heat flow in a material is often limited by lack of spatial resolution. Here, we use a diamond-nanocrystal-hosted nitrogen-vacancy centre attached to the apex of a silicon thermal tip as a local temperature sensor. We apply an electrical current to heat up the tip and rely on the nitrogen vacancy to monitor the thermal changes the tip experiences as it is brought into contact with surfaces of varying thermal conductivity. By combining atomic force and confocal microscopy, we image phantom microstructures with nanoscale resolution, and attain excellent agreement between the thermal conductivity and topographic maps. …

System And Method For Estimating States Of Spacecraft In Planet-Moon Environment, Piyush Grover

Department of Mechanical and Materials Engineering: Faculty Publications

A method estimates a state of a spacecraft in a planet-moon environment by executing iteratively a particle filter. The particle filter comprising integrates individually states of each particle of the particle filter according to a probability-evolution equation using a model of the state of the spacecraft represented as a planar circular restricted three-body problem and determines a prior probability of each particle as a previous posterior probability of a corresponding particle during a previous iteration. A joint probability distribution of the state of the spacecraft is determines using the states of each particle and the prior probabilities of each particle …

An Estimate Of The Second-Order In-Plane Acceleration Sensitivity Of A Y-Cut Quartz Thickness-Shear Resonator, Huijing He, Jiashi Yang, John A. Kosinski

Department of Mechanical and Materials Engineering: Faculty Publications

We perform a theoretical analysis of the second-order in-plane acceleration sensitivity of a Y-cut quartz thick-ness-shear mode resonator. The second-order nonlinear theory of elasticity for anisotropic crystals is used to determine the biasing fields in the resonator under in-plane acceleration. The acceleration-induced frequency shift is determined from a per-turbation analysis based on the plate equations for small-amplitude vibrations superposed on a finite bias. We show that, whereas the first-order acceleration-induced frequency shift is zero for a structurally symmetric resonator under in-plane ac-celeration, the second-order frequency shift is nonzero and is quadratic in the acceleration. As the fourth-order nonlinear elastic constants …

Biodegradable Medical Device Having An Adjustable Degradation Rate And Methods Of Making The Same, Yuebin Guo, Michael Sealy, Meisam Salahshoor Pirsoltan

Department of Mechanical and Materials Engineering: Faculty Publications

Disclosed herein are biodegradable medical devices comprising biodegradable material (e.g., magnesium-calcium alloys) having an adjustable rate of degradation that can be used in various applications, including, but not limited to, drug delivery applications, cardiovascular applications, and orthopedic applications to make biodegradable and biocompatible devices. Also disclosed herein are methods of making biodegradable medical devices comprising biodegradable materials by using, for instance, hybrid dry cutting/hydrostatic burnishing.

Traction-Separation Relationships For Hydrogen-Induced Grain Boundary Embrittlement In Nickel Via Molecular Dynamics Simulations, Wesley Allen Barrows

Graduate Theses and Dissertations

The deleterious effects of atomic and molecular hydrogen on the mechanical properties of metals have long been observed. Although several theories exist describing the mechanisms by which hydrogen negatively influences the failure of materials, a consensus has yet to be reached regarding the exact mechanism or combination of mechanisms. Two mechanisms have gained support in explaining hydrogen’s degradative role in non-hydride forming metals: hydrogen-enhanced localized plasticity and hydrogen-enhanced decohesion. Yet, the interplay between these mechanisms and microstructure in metallic materials has not been explained. Accordingly, for this thesis, the three main objectives are: (i) to develop a numerical methodology to …

Non-Wetting Surface-Driven High-Aspect-Ratio Crystalline Grain Growth For Efficient Hybrid Perovskite Solar Cells, Cheng Bi, Qi Wang, Yongbo Yuan, Zhengguo Xiao, Jinsong Huang

Department of Mechanical and Materials Engineering: Faculty Publications

Large-aspect-ratio grains are needed in polycrystalline thin-film solar cells for reduced charge recombination at grain boundaries; however, the grain size in organolead trihalide perovskite (OTP) films is generally limited by the film thickness. Here we report the growth of OTP grains with high average aspect ratio of 2.3–7.9 on a wide range of non-wetting hole transport layers (HTLs), which increase nucleus spacing by suppressing heterogeneous nucleation and facilitate grain boundary migration in grain growth by imposing less drag force. The reduced grain boundary area and improved crystallinity dramatically reduce the charge recombination in OTP thin films to the level in …

Analysis Of A Carbon Fiber Reinforced Polymer Impact Attenuator For A Formula Sae Vehicle Using Finite Element Analysis, John T. Rappolt

Master's Theses

The Hashin failure criteria and damage evolution model for laminated fiber reinforced polymers are explored. A series of tensile coupon finite element analyses are run to characterize the variables in the physical model as well as modeling techniques for using an explicit dynamic solver for a quasi-static problem. An attempt to validate the model on an axial tube crush is presented. It was found that fiber buckling was not occurring at the impactor-tube interface. Results and speculation as to why the failure initiation is incorrect are discussed. Lessons learned from the tube crush are applied successfully to the quasi-static Formula …

Local Control Robotic Surgical Devices And Related Methods, Eric Markvicka, Tom Frederick, Jack Mondry, Joe Bartels, Shane Farritor

Department of Mechanical and Materials Engineering: Faculty Publications

The various robotic medical devices include robotic devices that are disposed within a body cavity and positioned using a support component disposed through an orifice or opening in the body cavity. Additional embodiments relate to devices having arms coupled to a device body wherein the device has a minimal profile such that the device can be easily inserted through smaller incisions in comparison to other devices without such a small profile. Further embodiments relate to methods of operating the above devices.

Methods And Systems For Handling Or Delivering Materials For Natural Orifice Surgery, Carl Nelson, Jeff Midday, Dimitry Oleynikov, Alan Goyzueta

Department of Mechanical and Materials Engineering: Faculty Publications

The embodiments disclosed herein relate to various medical systems, including systems that can be used in conjunction with medical devices used in endoscopic surgery. Certain embodiments include various material handling devices that can transport materials between the inside and the outside of an endoscopic surgery patient.

Chloride Incorporation Process In Ch3Nh3Pbi3-XClX Perovskites Via Nanoscale Bandgap Maps, Jungseok Chae, Qingfeng Dong, Jinsong Huang, Andrea Centrone

Department of Mechanical and Materials Engineering: Faculty Publications

CH₃NH₃PbI_3-xCl_x perovskites enable fabrication of highly efficient solar cells. Chloride ions benefit the morphology, carrier diffusion length and stability of perovskite films; however, whether those benefits stem from the presence of Cl⁻ in the precursor solution or from their incorporation in annealed films is debated. In this work, the photothermal induced resonance (PTIR), an in situ technique with nanoscale resolution, is leveraged to measure the bandgap of CH₃NH₃PbI_3-xCl_x films obtained by a multicycle coating process that produces high efficiency (≈16 %) solar cells. Because chloride …

Role Of Interphase In The Mechanical Behavior Of Silica/Epoxy Resin Nanocomposites, Yi Hua, Linxia Gu, Sundaralingam Premaraj, Xiaodong Zhang

Department of Mechanical and Materials Engineering: Faculty Publications

A nanoscale representative volume element has been developed to investigate the effect of interphase geometry and property on the mechanical behavior of silica/epoxy resin nanocomposites. The role of interphase–matrix bonding was also examined. Results suggested that interphase modulus and interfacial bonding conditions had significant influence on the effective stiffness of nanocomposites, while its sensitivities with respect to both the thickness and the gradient property of the interphase was minimal. The stiffer interphase demonstrated a higher load-sharing capacity, which also increased the stress distribution uniformity within the resin nanocomposites. Under the condition of imperfect interfacial bonding, the effective stiffness of nanocomposites …

Relevance Of Blood Vessel Networks In Blast-Induced Traumatic Brain Injury, Yi Hua, Shengmao Lin, Linxia Gu

Department of Mechanical and Materials Engineering: Faculty Publications

Cerebral vasculature is a complex network that circulates blood through the brain. However, the role of this networking effect in brain dynamics has seldom been inspected. This work is to study the effects of blood vessel networks on dynamic responses of the brain under blast loading. Voronoi tessellations were implemented to represent the network of blood vessels in the brain. The brain dynamics in terms of maximumprincipal strain (MPS), shear strain (SS), and intracranial pressure (ICP) weremonitored and compared. Results show that blood vessel networks significantly affected brain responses.The increased MPS and SS were observed within the brain embedded with …

In Situ Longitudinal Pre-Stretch In The Human Femoropopliteal Artery, Alexey Kamenskiy, Andreas Seas, Grant Bowen, Paul Deegan, Anastasia Desyatova, Nick Bohlim, William Poulson, Jason N. Mactaggart

Department of Mechanical and Materials Engineering: Faculty Publications

In situ longitudinal (axial) pre-stretch (LPS) plays a fundamental role in the mechanics of the femoropopliteal artery (FPA). It conserves energy during pulsation and prevents buckling of the artery during limb movement. We investigated how LPS is affected by demographics and risk factors, and how these patient characteristics associate with the structural and physiologic features of the FPA. LPS was measured in n=148 fresh human FPAs (14–80 years old). Mechanical properties were characterized with biaxial extension and histopathological characteristics were quantified with Verhoeff-Van Gieson Staining. Constitutive modeling was used to calculate physiological stresses and stretches which were then analyzed …

Asphalt Composition, David Allen, Flavio Souza, Yong-Rak Kim, Roberto Soares

Department of Mechanical and Materials Engineering: Faculty Publications

A computational method is provided for predicting roadway failure due to degradation of the roadway over time as a function of the input loads, the roadway geometry, the material properties of the constituents in the asphaltic pavement, the shape, distribution, orientation and volume fractions of the constituents, and environmental conditions. The unique and new feature of the method is that it employs several physically based predictive methodologies simultaneously.

Extracting Continuum-Like Deformation And Stress From Molecular Dynamics Simulations, Lili Zhang, John Jasa, George Gazonas, Antoine Jerusalem, Mehrdad Negahban

Department of Mechanical and Materials Engineering: Faculty Publications

We present methods that use results from molecular dynamics (MD) simulations to construct continuum parameters, such as deformation gradient and Cauchy stress, from all or any part of an MD system. These parameters are based on the idea of minimizing the difference between MD measures for deformation and traction and their continuum counterparts. The procedures should be applicable to non-equilibrium and inhomogeneous systems, and to any part of a system, such as a polymer chain. The resulting procedures provide methods to obtain first and higher order deformation gradients associated with any subset of the MD system, and associated expressions for …

Simulation Of Infiltrating Rate Driven By Surface Tension-Viscosity Of Liquid Elements From The Titanium Group Into A Packed Bed, Arturo Medina

Open Access Theses & Dissertations

The simulation of infusion of molten reactive metals (e.g., yttrium) into a porous, carbide packed bed to create carbide and boride composites was studied at ultrahigh temperatures (>1700°C). The infusion was investigated through a computational fluid dynamic (CFD) system of capillary pores and compared to a predicted analytical calculation formulated by Selmak and Rhines. Simulations of two-phase flow penetration of yttrium into a packed bed of B4C were investigated and compared with titanium, zirconium, hafnium, and samarium liquids. The non-reactive, liquid metal infusion was primarily driven by the surface tension and viscosity. The liquid metal depth and rate of …

Reaction Of Liquid Aluminium- Samarium Alloys With B4c At Ultra High Temperatures, Sanjay Shantha-Kumar

Open Access Theses & Dissertations

Reactive studies between a packed bed of B4C and Al-Sm-Me (Me = Ti, Zr, Hf) alloy melts were carried out under a pseudo-isopiestic thermodynamic system. A graphite enclosure isolated the system under a temperature gradient with one end reaching temperatures greater than 1800 K and the opposite end of the graphite enclosure contains liquid Al with temperatures approximating 950 K. The liquid Al establishes an oxygen potential to control oxidation of very reactive elements (i.e., Al, Sm and Ti). The Al-Sm-Me alloy infuses into a packed bed of B4C reacting exothermically to form borides and carbides depending on the thermodynamic …

Defeating Anisotropy In Material Extrusion 3d Printing Via Materials Development, Ángel Ramón Torrado Pérez

Open Access Theses & Dissertations

Additive Manufacturing technologies has been in continuous development for more than 35 years. Specifically, the later denominated Material Extrusion Additive Manufacturing (MEAM), was first developed by S. Scott Crump around 1988 and trademarked later as Fused Deposition Modeling (FDM). Although all of these technologies have been around for a while, it was not until recently that they have been more accessible to everyone. Today, the market of 3D printers covers all ranges of price, from very specialized, heavy and expensive machines, to desktop printers of only a few cubic inches in volume. Until recently, FDM technology had remained somewhat stagnant …

Design And Analysis Of A Novel Latch System Implementing Fiber-Reinforced Composite Materials, Francisco Guevara

Open Access Theses & Dissertations

The use of fiber-reinforced composite materials have increased in the last four decades in high technology applications due to their exceptional mechanical properties and low weight. In the automotive industry carbon fiber have become popular exclusively in luxury cars because of its high cost. However, Carbon-glass hybrid composites offer an effective alternative to designers to implement fiber-reinforced composites into several conventional applications without a considerable price increase maintaining most of their mechanical properties. A door latch system is a complex mechanism that is under high loading conditions during car accidents such as side impacts and rollovers. Therefore, the Department of …