Mechanical Engineering Commons^™

Ultrathin Coding Metasurface For Underwater Wave Focusing, Branching And Self-Bending Generation With One Single Actuator, Lixie Song, Zhong Chen, Mehrdad Negahban, Lei Liang, Zheng Li, Zheng Wu

Department of Mechanical and Materials Engineering: Faculty Publications

A novel metasurface is proposed that aims to generate underwater acoustic waves with various functions by only one actuator. Each metasurface unit consists of an air cavity sandwiched on one side by a vibration plate and connecting rubber supports. By properly selecting the ratio of the plate to unit lengths, a phase shift of π can be attained to constitute a binary coding metasurface. Three demonstrations, including focusing, branching and self-bending waves, are chosen to validate the functionality of the design. The design is also shown to work over a wide frequency range through changing the ratio. In addition, the …

Machine Learning Assisted Metamaterial‑Based Reconfigurable Antenna For Low‑Cost Portable Electronic Devices, Shobhit K. Patel, Jaymit Surve, Vijay Katkar, Juveriya Parmar

Department of Mechanical and Materials Engineering: Faculty Publications

Antenna design has evolved from bulkier to small portable designs but there is a need for smarter antenna design using machine learning algorithms that can meet today’s high growing demand for smart and fast devices. Here in this research, main focus is on developing smart antenna design using machine learning applicable in 5G mobile applications and portable Wi-Fi, Wi-MAX, and WLAN applications. Our design is based on the metamaterial concept where the patch is truncated and etched with a split ring resonator (SRR). The high gain requirement is met by adding metamaterial superstrates having thin wires (TW) and SRRs. The …

Symmetric Or Asymmetric Glide Resistance To Twinning Disconnection?, Mingyu Gong, Houyu Ma, Kunming Yang, Yue Liu, Jian-Feng Nie, Jian Wang

Department of Mechanical and Materials Engineering: Faculty Publications

Successive gliding of twinning disconnections (TDs) creates three-dimensional twins in parent crystal and accommodates shear deformation. It is generally recognized that TD is subject to the same Peierls stress as it glides forward or backward because of its dislocation character and the twofold rotation symmetry of the twin plane. Based on atomistic simulations, we demonstrate that the glide of TDs may be subject to a symmetric or asymmetric resistance corresponding to step character, symmetric resistance for A/A type steps but asymmetric resistance for A/B type steps, where A and B represent crystallographic planes in twin and matrix. Furthermore, we experimentally …

Recent Advances In Biosensors For Detection Of Covid-19 And Other Viruses, Shobhit K. Patel, Jaymit Surve, Juveriya Parmar, Kawsar Ahmed, Francis M. Bui, Fahad Ahmed Al-Zahrani

Department of Mechanical and Materials Engineering: Faculty Publications

This century has introduced very deadly, dangerous, and infectious diseases to humankind such as the influenza virus, Ebola virus, Zika virus, and the most infectious SARS-CoV-2 commonly known as COVID-19 and have caused epidemics and pandemics across the globe. For some of these diseases, proper medications, and vaccinations are missing and the early detection of these viruses will be critical to saving the patients. And even the vaccines are available for COVID-19, the new variants of COVID-19 such as Delta, and Omicron are spreading at large. The available virus detection techniques take a long time, are costly, and complex and …

A Robot-Assisted Acoustofluidic End Effector, Jan Durrer, Prajwal Agrawal, Ali Ozgul, Stephen C.F. Neuhauss, Nitesh Nama, Daniel Ahmed

Department of Mechanical and Materials Engineering: Faculty Publications

Liquid manipulation is the foundation of most laboratory processes. For macroscale liquid handling, both do-it-yourself and commercial robotic systems are available; however, for microscale, reagents are expensive and sample preparation is difficult. Over the last decade, lab-on-a-chip (LOC) systems have come to serve for microscale liquid manipulation; however, lacking automation andmulti-functionality. Despite their potential synergies, each has grown separately and no suitable interface yet exists to link macro-level robotics with micro-level LOC or microfluidic devices. Here, we present a robot-assisted acoustofluidic end effector (RAEE) system, comprising a robotic arm and an acoustofluidic end effector, that combines robotics and microfluidic functionalities.We …

Smooth Muscle Cells Affect Differential Nanoparticle Accumulation In Disturbed Blood Flow-Induced Murine Atherosclerosis, Hunter Miller, Morgan A. Schake, Badrul Alam Bony, Evan T. Curtis, Conner C. Gee, Ian Mccue, Thomas J. Ripperda Jr., Yiannis S. Chatzizisis, Forrest Kievit, Ryan M. Pedrigi

Department of Mechanical and Materials Engineering: Faculty Publications

Atherosclerosis is a lipid-driven chronic inflammatory disease that leads to the formation of plaques in the inner lining of arteries. Plaques form over a range of phenotypes, the most severe of which is vulnerable to rupture and causes most of the clinically significant events. In this study, we evaluated the efficacy of nanoparticles (NPs) to differentiate between two plaque phenotypes based on accumulation kinetics in a mouse model of atherosclerosis. This model uses a perivascular cuff to induce two regions of disturbed wall shear stress (WSS) on the inner lining of the instrumented artery, low (upstream) and multidirectional (downstream), which, …

Microfabricated Platforms To Investigate Cell Mechanical Properties, Amir M. Esfahani, Grayson Minnick, Jordan Rosenbohm, Haiwei Zhai, Xiaowei Jin, Bahareh Tajvidi Safa, Justin Brooks, Ruiguo Yang

Department of Mechanical and Materials Engineering: Faculty Publications

Mechanical stimulation has been imposed on living cells using several approaches. Most early investigations were conducted on groups of cells, utilizing techniques such as substrate deformation and flow-induced shear. To investigate the properties of cells individually, many conventional techniques were utilized, such as AFM, optical traps/optical tweezers, magnetic beads, and micropipette aspiration. In specific mechanical interrogations, microelectro- mechanical systems (MEMS) have been designed to probe single cells in different interrogation modes. To exert loads on the cells, these devices often comprise piezo-electric driven actuators that attach directly to the cell or move a structure on which cells are attached. Uniaxial …

Phase Transformation And Strain Hardening Mechanisms In Advanced Engineering Steels, Hangyu Dong

Open Access Theses & Dissertations

Strain hardening and associated deformation mechanisms play a determining role in the performance of metallic materials. The objective of the doctoral research was to explore and fundamentally understand the strain hardening mechanisms in the next generation of advanced engineering steels. Two main work hardening mechanisms, notably, twinning-induced plasticity (TWIP) and transformation-induced plasticity (TRIP)) were identified that governed strength and ductility. In the nanograined austenitic steel with high strength-high ductility combination, processed by the novel phase reversion concept, twinning-induced plasticity (TWIP) was the governing deformation mechanism and contributed to good ductility. In striking contrast, transformation-induced plasticity (TRIP) was the deformation mechanism …

Synthesis And Characterization Of Tin (Sn) Incorporated Ga2o3, Guillermo Nicolas Gutierrez

Open Access Theses & Dissertations

In this work, we report on the synthesis, characterization of tin (Sn) incorporated gallium oxide Ga2O3 compounds, also included in this work is the effect of tin concentration related to the optical and electrochemical properties. The Sn incorporation into Ga2O3 creates a significant reduction in the bandgap and causes a nonlinear optical activity as the concentration varies. Substantial investigation performed to the structure, phase, and morphology of the mixed compounds governed by the stoichiometry equation Ga2−2xSnxO3-ɗ indicates that the Sn incorporation from 0.00 ≤ x ≤ 0.30 has a significant effect on these properties. To synthesize the Ga-Sn-O compounds a …

Mechanical Properties And Microstructure Evolution Of Thermally Treated Laser Powder Bed Fusion Alsi10mg, Jorge Merino-Gomez

Open Access Theses & Dissertations

The optimization of mechanical properties with thermal postprocessing treatments was investigated in this study across a wide variety of variants. The relationship between heat treatments and the impacts on the mechanical properties and microstructure of printed materials is a crucial part of additive manufacturing. As a result, the current paper provides a comprehensive overview of postprocess heat treatments for Laser Powder Bed Fusion fabricated AlSi10Mg alloy, including stress relief anneals at 190 and 285 degrees Celsius for 2 hours, hot isostatic pressing at 515 degrees Celsius for 3 hours, hot isostatic pressing + T6 treatment for 6 hours, and final …

Quick - Release End Effector Tool Interface, Shane Farritor, Thomas Frederick

Department of Mechanical and Materials Engineering: Faculty Publications

The various embodiments herein relate to a coupling apparatus for a medical device having a coupler body, a cavity defined in the coupler body, a rotatable drive component disposed within the cavity and having at least two pin receiving openings, and an actuable locking ring disposed around the cavity.

Fatigue Damage Quantification And Life Estimation With Provision For Microstructure, Arash Pourbagheri Jirandehi

LSU Doctoral Dissertations

This dissertation provides methodologies for the quantification of different forms of fatigue damage by considering the role of microstructure. The laws of thermodynamics in conjunction with Finite Element Method (FEM) are utilized to devise thermodynamically-base frameworks for the estimation of cyclic damage in polycrystalline metals. Accordingly, a microstructure-sensitive platform for fatigue life estimation is introduced. The proposed framework is assessed for 3D printed metallic alloys at room and elevated temperatures. Further, it is used to analyze the fatigue performance difference between additively manufactured Inconel 718 in three print orientations. This research is of fundamental vital interest because it ensures that …

In Situ Characterization Of Tensile Behavior Of Laser Rapid Solidified Al–Si Heterogeneous Microstructures, Bingqiang Wei, Wenqian Wu, Dongyue Xie, Huai-Hsun Lien, Metin Kayitmazbatir, Amit Misra, Jian Wang

Department of Mechanical and Materials Engineering: Faculty Publications

Heterogeneous Al–Si microstructure comprising of sub-micron-scale Al dendrites and nanoscale Al–Si fibrous eutectic was fabricated by processing as-cast Al-20wt.%Si alloy using laser rapid solidification. In situ tension tests explored high tensile strength ( ∼ 600 MPa) and ductility ( ∼ 10%) and high strain hardening rate ( ∼ 7 GPa). Microstructural characterization revealed the plastic co[1]deformation mechanisms between soft Al dendrites and hard nanoscale Al–Si eutectic. The progression of plasticity in nanoscale Al–Si eutectic with increasing applied strain is accommodated by dislocation plasticity in the nano-Al channels and cracking Si nanofibers. The propagation of nano-cracks is suppressed by surrounding Al, …

Digitally Twinned Additive Manufacturing: Detecting Flaws In Laser Powder Bed Fusion By Combining Thermal Simulations With In-Situmeltpool Sensor Data, R Yavari, A Riensche, E Tekerek, L Jacquemetton, H Halliday, M Vandever, A Tenequer, V Perumal, A Kontsos, Z Smoqi, K Cole, P Rao

Department of Mechanical and Materials Engineering: Faculty Publications

The goal of this research is the in-situ detection of flaw formation in metal parts made using the laser powder bed fusion (LPBF) additive manufacturing process. This is an important area of research, because, despite the considerable cost and time savings achieved, precision-driven industries, such as aerospace and biomedical, are reticent in using LPBF to make safety–critical parts due to tendency of the process to create flaws. Another emerging concern in LPBF, and additive manufacturing in general, is related to cyber security – malicious actors may tamper with the process or plant flaws inside a part to compromise its performance. …

Contact Angle Measurement Using A Hele-Shaw Cell: A Proof-Of-Concept Study, Haipeng Zhang, Jacob Gottberg, Sangjin Ryu

Department of Mechanical and Materials Engineering: Faculty Publications

Contact angle is an important property to quantify the wettability of a solid surface with a liquid, which characterizes interactions of the solid-liquid pair. Generally, to measure contact angle, special instruments such as a goniometer are necessary, but they are not readily available in certain research settings. In this study, an alternative method to measure contact angle based on a Hele-Shaw cell, microscopy imaging, and image processing is suggested. In this method, a liquid drop is injected into a transparent Hele-Shaw cell, the meniscus of the drop is captured in the top or bottom view using a brightfield microscope, and …

Contact Angle Measurement Using A Hele-Shaw Cell: A Proof-Of-Concept Study, Haipeng Zhang, Jacob Gottberg, Sangjin Ryu

Department of Mechanical and Materials Engineering: Faculty Publications

Contact angle is an important property to quantify the wettability of a solid surface with a liquid, which characterizes interactions of the solid-liquid pair. Generally, to measure contact angle, special instruments such as a goniometer are necessary, but they are not readily available in certain research settings. In this study, an alternative method to measure contact angle based on a Hele-Shaw cell, microscopy imaging, and image processing is suggested. In this method, a liquid drop is injected into a transparent Hele-Shaw cell, the meniscus of the drop is captured in the top or bottom view using a brightfield microscope, and …

Methods , Systems , And Devices Relating To Surgical End Effectors, Shane M. Farritor, Thomas Frederick, Joe Bartels

Department of Mechanical and Materials Engineering: Faculty Publications

The embodiments disclosed herein relate to various medical device components , including components that can be incorporated into robotic and / or in vivo medical devices, and more specifically including end effectors that can be incorporated into such devices. Certain end effector embodiments include various vessel cautery devices that have rotational movement as well as cautery and cutting functions while maintaining a relatively compact structure. Other end effector embodiments include various end effector devices that have more than one end effector.

Robotic Surgical Devices , Systems , And Related Methods, Shane Farritor, Erik Mumm, Philip Chu, Nishant Kumar, Jason Dumpert, Yutaka Tsutano

Department of Mechanical and Materials Engineering: Faculty Publications

The embodiments disclosed herein relate to various medical device components, including components that can be incorporated into robotic and / or in vivo medical devices. Certain embodiments include various modular medical devices for in vivo medical procedures.

In Vivo Printing Of Growth Factor-Eluting Adhesive Scaffolds Improves Wound Healing, Kristo Nuutila, Mohamadmahdi Samandari, Yori Endo, Yuteng Zhang, Jacob Quint, Tannin A. Schmidt, Ali Tamayol, Indranil Sinha

Department of Mechanical and Materials Engineering: Faculty Publications

Acute and chronic wounds affect millions of people around the world, imposing a growing financial burden on patients and hospitals. Despite the application of current wound management strategies, the physiological healing process is disrupted in many cases, resulting in impaired wound healing. Therefore, more efficient and easy-to-use treatment modalities are needed. In this study, we demonstrate the benefit of in vivo printed, growth factor-eluting adhesive scaffolds for the treatment of full-thickness wounds in a porcine model. A custom-made handheld printer is implemented to finely print gelatin-methacryloyl (GelMA) hydrogel containing vascular endothelial growth factor (VEGF) into the wounds. In vitro and …

Development Of Novel Battery Materials For Lithium-Ion Batteries And Beyond, Jiyu Cai

Graduate Theses and Dissertations

As fossil fuels are depleting and causing environmental issues, it becomes imperative to widely implement renewable energies (e.g., solar and wind power). In this context, electrical energy storage (EES) systems are essential to accommodate the intermittent supply and uneven distribution of renewable energies. To this end, high-energy-density EES devices are highly demanded, such as rechargeable batteries. This dissertation presents my efforts in developing novel battery materials for lithium-ion batteries (LIBs), sodium-ion batteries (SIBs), and solidstate lithium batteries (SSLBs). These efforts include electrochemical evaluations of battery materials, surface modifications of electrodes via atomic layer deposition (ALD), and advanced characterizations of batteries …

Phase-Field Modeling Of The Polymer Membrane Formation Process For Micro- And Ultra-Filtration, Michael Rosario Cervellere

Graduate Theses and Dissertations

Porous polymer membrane filters are widely used in separation and filtration process. Micro- and ultra-filtration membranes are commonly used in biopharmaceutical applications such as filtering viruses and separating proteins from a carrier solution. The formation of these membrane filters via phase inversion is a complex and interconnected process where varying casting conditions can have a wide variety of effects on the final membrane morphol- ogy. Tailoring membrane filters for specific performance characteristics is a tedious and time consuming process. The time and length scales of membrane formation make it extremely difficult to experimentally observe membrane formation. Modeling the membrane formation …

Influence Of Extracellular Matrix Stiffness And Topography On Neuronal Cell Behavior And Neurite Outgrowth, Mohan Yasodharababu

Graduate Theses and Dissertations

The focus of regeneration therapy for traumatic brain injuries and Alzheimer's disease is on the promotion and growth of neuronal cells. In vitro research attempts to improve this by modifying the stiffness and topography of the extracellular matrix (ECM). However, the limitations of in vitro experiments make it difficult to control the individual factors influencing neuronal cell growth. A computational model can be used to decouple individual factors and study them individually to gain a better understanding of the mechanics between the neuronal cell and ECM, which will aid in the design of in vitro experimental studies.

This study develops …

Control Of Change Of Phase Through Physical Surface Shaping, Troy Anderson, Sidy Ndao, Craig Zuhlke, Dennis Alexander, George Gogos

Department of Mechanical and Materials Engineering: Faculty Publications

A system embodiment includes , but is not limited to , a solid structure configure to contact each of a material in a liquid phase and a material in a vapor phase , the solid structure including a plurality of microstructures protruding at angles relative to a horizontal plane ; and a layer of nanoparticles positioned on the plurality of microstructures , the layer of nanoparticles having a composition that is at least one of a same material as the plurality of microstructures and an oxide of the same material as the plurality of microstructures , the plurality of microstructures …

Fluid-Structure Interaction Of Nrel 5-Mw Wind Turbine, Mohamed Sayed Elkady Abd-Elhay

Theses and Dissertations

Wind energy is considered one of the major sources of renewable energy. Nowadays, wind turbine blades could exceed 100 m to maximize the generated power and minimize produced energy cost. Due to the enormous size of the wind turbines, the blades are subjected to failure by aerodynamics loads or instability issues. Also, the gravitational and centrifugal loads affect the wind turbine design because of the huge mass of the blades. Accordingly, wind turbine simulation became efficient in blade design to reduce the cost of its manufacturing. The fluid-structure interaction (FSI) is considered an effective way to study the turbine's behavior …

Minimally Invasive Delivery Of 3d Shape Recoverable Constructs With Ordered Structures For Tissue Repair, Shixuan Chen, Mark Alan Carlson, Xiaowei Li, Aleem Siddique, Wuqiang Zhu, Jingwei Xie

Department of Mechanical and Materials Engineering: Faculty Publications

Minimally invasive procedures are becoming increasingly more common in surgery. However, the biomaterials capable of delivering biomimetic, three-dimensional (3D) functional tissues in a minimally invasive manner and exhibiting ordered structures after delivery are lacking. Herein, we reported the fabrication of gelatin methacryloyl (GelMA)-coated, 3D expanded nanofiber scaffolds and their potential applications in minimally invasive delivery of 3D functional tissue constructs with ordered structures and clinically appropriate sizes (4 cm × 2 cm × 1.5 mm). GelMA-coated, expanded 3D nanofiber scaffolds produced by combining electrospinning, gas-foaming expansion, hydrogel coating, and crosslinking are extremely shape recoverable after release of compressive strain, displaying …

Maize Tassel Detection From Uav Imagery Using Deep Learning, Aziza Alzadjali, Mohammed H. Alali, Arun Narenthiran Weeranampalayam Sivakumar, Jitender S. Deogun, Stephen Scott, James C. Schnable, Yeyin Shi

Department of Mechanical and Materials Engineering: Faculty Publications

The timing of flowering plays a critical role in determining the productivity of agricultural crops. If the crops flower too early, the crop would mature before the end of the growing season, losing the opportunity to capture and use large amounts of light energy. If the crops flower too late, the crop may be killed by the change of seasons before it is ready to harvest. Maize flowering is one of the most important periods where even small amounts of stress can significantly alter yield. In this work, we developed and compared two methods for automatic tassel detection based on …

Uavs For Vegetation Monitoring: Overview And Recent Scientific Contributions, Ana I. De Castro, Yeyin Shi, Joe Mari Maja, Jose M. Pena

Department of Mechanical and Materials Engineering: Faculty Publications

This paper reviewed a set of twenty-one original and innovative papers included in a special issue on UAVs for vegetation monitoring, which proposed new methods and techniques applied to diverse agricultural and forestry scenarios. Three general categories were considered: (1) sensors and vegetation indices used, (2) technological goals pursued, and (3) agroforestry applications. Some investigations focused on issues related to UAV flight operations, spatial resolution requirements, and computation and data analytics, while others studied the ability of UAVs for characterizing relevant vegetation features (mainly canopy cover and crop height) or for detecting different plant/crop stressors, such as nutrient content/deficiencies, water …

Three-Dimensional Shape Analysis Of Peripapillary Retinal Pigment Epithelium-Basement Membrane Layer Based On Oct Radial Images, Junfei Tong, Pengfei Dong, Sachin Kedar, Deepta Ghate, Linxia Gu

Department of Mechanical and Materials Engineering: Faculty Publications

The peripapillary retinal pigment epithelium-basement membrane (ppRPE/BM) layer angle was recently proposed as a potential index for estimating intracranial pressure noninvasively. However, the ppRPE/BM layer angle, measured from the optical coherence tomography (OCT) scans, varied across the radial directions of the optic disc. This made the ppRPE/BM layer angle difficult to be utilized in its full potential. In this study, we developed a mathematical model to quantify the ppRPE/BM layer angles across radial scans in relation to the ppRPE/BM 3D morphology in terms of its 3D angle and scanning tilt angles. Results showed that the variations of the ppRPE/BM layer …

On The Comparison Of Flow Physics Between Minimal And Extended Flow Units In Turbulent Channels, Ethan A. Davis, Siamak Mirfendereski, Jae Sung Park

Department of Mechanical and Materials Engineering: Faculty Publications

Direct numerical simulations were performed to study the effects of the domain size of a minimal flow unit (MFU) and its inherent periodic boundary conditions on flow physics of a turbulent channel flow in a range of 200 ≤ Re_τ ≤ 1000. This was accomplished by comparing turbulent statistics with those computed in sub-domains (SD) of extended domain simulations. The dimensions of the MFU and SD were matched, and SD dynamics were set to minimize artificial periodicities. Streamwise and spanwise dimensions of healthy MFUs were found to increase linearly with Reynolds number. It was also found that both MFU …

Synthesis And Characterization Of Functiona Materials For 3d Printed Composites, Elizabeth Irene Reza

Open Access Theses & Dissertations

The following body of work encompasses the synThesis, upscaling, additive manufacturing, and characterization of microspheres as functional fillers incorporated into polymer syntactic foams. Synthesizing microspheres permits control over morphology, dispersion of particles, and size while the use of direct write manufacturing allowed for the controllability of filler orientation. Two different syntactic foams were developed from similar methodologies: (1) a silicone syntactic foam (2) epoxy syntactic foam. The silicone epoxy foam showed an increasing in damping and elastic modulus. The epoxy syntactic foams showed an enhanced thermal and electrical properties.