Mechanical Engineering Commons^™

Optimization Of 3d Printed Mold Performance For Injection Molding Via Hollow Infill Patterns, Alan Fong

University Honors Theses

The applicability of hollow infill patterns has been explored for its applications in making 3D printed polymer-based injection molds in the additive manufacturing industry. Hollow infill patterns offer a significant reduction in material costs as well as the opportunity for reducing the cooling times via pumping a coolant fluid through the hollow cavity in a similar fashion to traditional conformal cooling channels. A 3D Jacks Support Hollow mold model was determined to be the best performing design. FEA analysis was conducted to determine the maximum reduction in internal volume (percentage of material saved) that could be achieved without exceeding the …

Mechanical Failure Of Metal/Ceramic Interfacial Regions Under Shear And Tensile Loading, Xiaoman Zhang

LSU Doctoral Dissertations

Quantitative assessment of the adhesion strength of ceramic hard coatings on substrates is a subject of great technological importance as well as current scientific relevance. Achievement of reliable and quantitative measurements of interfacial strength has proven difficult over the past two decades. In this dissertation, how the deformation and fracture behavior of ceramic/metal/substrate interfacial regions under shear and tensile loading is influenced by the structure and chemical composition of the interfacial region were observed and discussed. Interfacial shear failure experiments were carried out on focused ion beam fabricated micro pillars containing interfacial regions of ceramic/metal/substrate systems. Detailed characterization was carried …

Experimental Investigation Of The Performance Of A Hybrid Self-Healing System In Porous Asphalt Under Fatigue Loadings, Shi Xu, Liu Xueyan, Amir Tabakovic, Erik Schlangen

Articles

Self-healing asphalt, which is designed to achieve autonomic damage repair in asphalt pavement, offers a great life-extension prospect and therefore not only reduces pavement maintenance costs but also saves energy and reduces CO2 emissions. The combined asphalt self-healing system, incorporating both encapsulated rejuvenator and induction heating, can heal cracks with melted binder and aged binder rejuvenation, and the synergistic effect of the two technologies shows significant advantages in healing efficiency over the single self-healing method. This study explores the fatigue life extension prospect of the combined healing system in porous asphalt. To this aim, porous asphalt (PA) test specimens with …

The Role Of Scenography In The Narration Of The Inner Space Of Contemporary Museums Through Employment The Space Staging, Shamael M. W. Al-Dabbagh, Dania Saleh Yaheia Al-Jaboury

Al-Esraa University College Journal for Engineering Sciences

In the recent period, several design mechanisms have emerged related to the design of internal spaces in architecture, specifically the museum spaces and associated with exhibitions, and the most important of these scenographic mechanisms are clearly and significantly adopted in the field of theater to design the stage and the scene that embodies the narrative vision and the idea of the theater director and scenographic designer to express what the text wants from Anecdotal expressing the objectives of the product of the text, therefore the research aimed to delve into the effect of the scenography mechanism on the contemporary architectural …

Evaluating The Performance Of The Jadriya Water Project For Water Treatment, Rana Mohammed Rasheed

Al-Esraa University College Journal for Engineering Sciences

For the purpose of evaluating the performance of the Al-Jadriya water project, water samples were taken before and after the sedimentation basins to find out the efficiency of the sedimentation ponds, as well as water samples were taken before and after the filtration basins, to know the efficiency of the filtration basins by conducting the following tests on them (Turbidity, TDS, TC, pH) to ensure that these ponds work properly. It was found that the efficiency rate of sedimentation ponds was 83%, which indicates the inefficiency of these ponds, as well as the inefficiency of the fast and slow mixing …

Possible Developments Of The Industrialization Of Appropriate Building Subsystem For Iraq, Wisam William Saleem Al-Ayoubi

Al-Esraa University College Journal for Engineering Sciences

Industrialization of building has developed very rapidly in industrialized countries as well as in many other parts of the world to fulfill the need for housing and public buildings after the Second World War. Prefabricated building is defined as a type of building that consists of several elements or modular units prepared in advance and assembled on-site. The term prefabricated indicates that these building elements are manufactured in the workshop or factory and then combined with other elements. Iraq has witnessed vital development in the construction industry sector. The study investigates the appropriate technology for Iraq, considering resources, economy, labor, …

Ion Exchange Method For Sulphate Removal From Treated Wastewater Of Al-Doura Refinery, Rana Mohammed Rasheed

Al-Esraa University College Journal for Engineering Sciences

The treated wastewater by the industrial Wastewater Treatment Plant (WWTP), commonly named (INGECO) in Al-Doura refinery, suffers from highly sulfate concentrations that exceed the EPA specified limits of 250 mg/L. Laboratory water quality historical data have been reviewed and analyzed to determine the annual rate, maximum, and peak sulfate concentrations, which were found to be 360 mg/L, 425 mg/L, and 550 mg/L, respectively. A field inspection was conducted to identify the reasons for the high sulfate concentrations in the wastewater of most refinery process units. It was found that the maximum required sulfate remaining concentration should not exceed 10 mg/L …

The Effect Of The Spirit Of The Place On The Formulation Of Emotion In Contemporary Arab-Islamic Architecture, Mahdi Saleh Al-Faraj, Dania Saleh Yaheia

Al-Esraa University College Journal for Engineering Sciences

Arab-Islamic architecture is characterized by both constants and variables, with spiritual aspects (content) representing the constants and physical aspects (form) representing the variables. It evolves based on changing times and needs, with compassion being a significant feature associated with its spiritual aspects. Compassion is essential for collective agreement and individual emotional connection in Arab-Islamic architecture. The present research aims to investigate the influence of the spirit of the place, as embraced by designers, on the emotional characteristics of contemporary Arab-Islamic architecture. The research problem identified is the lack of a theoretical concept regarding the impact of the spirit of the …

The Effect Of Bioenergy Systems On The Architectural Product The Effect Of Fung Shui And Biogetric To Achieve The Performance Of Architectural Space, Abdullah Saadon Al-Mamoory, Ann Samari Ibrahim

Al-Esraa University College Journal for Engineering Sciences

This research presents an analytical study exploring the vital systems of energy science and their influence on architecture by examining ancient environmental philosophies like Feng Shui in China and bio-geometry in Egypt. These philosophies serve as guiding principles for studying energy and its impact on human daily life, highlighting their effects on integrated ecosystems in the design of residential buildings at both external and internal levels. The study examines key aspects such as the influence of energy on furniture arrangement in living spaces. The primary objective is to establish a synergistic relationship between architectural design of residential spaces during occupancy …

Some Aspects Of The Suitability Of Three-Story Residential Buildings For Vertical Housing In Iraq, Wisam William Saleem Al-Ayoubi

Al-Esraa University College Journal for Engineering Sciences

This research initially aimed to examine the changes in housing since the 1930s, driven by rapid population growth and evolving lifestyles, juxtaposed with advancements in contemporary building materials that are environmentally compatible. After a comprehensive analysis of housing and living arrangements throughout history, including the evolution of open house units towards more interior-focused designs such as the Baghdadi house with its central courtyard, the study delved into the significant changes and the challenges posed by the rapid population growth. The focus of the study was on the viability of vertical housing in Iraq and the considerations related to low-rise residential …

Role Of Iconic Architecture In Sustainable Tourism Development, Basim H. H. Al-Majidi, Ann Samari Ibrahim

Al-Esraa University College Journal for Engineering Sciences

Architecture "is an expression of the way of life and the spirit of the ages and cultures in which I grew up" as the buildings speak for themselves. While tourism is a scenario "to define a city to an unfamiliar audience and acquire an identity for a citizen". Both architecture and tourism have been linked together since time immemorial. Architecture was the main aspect of attracting crowds, while tourism helped architecture survive the test of time as well as money. Both tourism and architecture operate in a symbiotic manner to break the lack of familiarity with any culture and to …

Development Of A Marine Biodegradable Target Balloon, Blake Samuel Robinson, Arash Sam Akhavi, David Leonardo Albarran-Martinez

Materials Engineering

The US Navy utilizes PVC target balloons, known as Killer Tomatoes, that are inflated onboard a naval vessel then deployed into the ocean to calibrate a variety of weaponry. The Navy has requested the investigation of biodegradable polymers to replace the PVC in attempts to reduce ocean waste that is generated from the leftover PVC material. After communicating with American Pacific Plastic Fabricators (APPF), the current manufacturer of the Killer Tomatoes, we gained an understanding of the manufacturing process and the material requirements that would allow a new material to be integrated into their current process. Two proprietary, trial polymers …

Fabricating Tinicu Ternary Shape Memory Alloy By Directed Energy Deposition Via Elemental Metal Powders, Yitao Chen, Xinchang Zhang, Mohammad Masud Parvez, Joseph William Newkirk, Frank W. Liou

Materials Science and Engineering Faculty Research & Creative Works

In this paper, a TiNiCu shape memory alloy single-wall structure was fabricated by the directed energy deposition technique with a mixture of elemental Ti, Ni, and Cu powders following the atomic percentage of Ti50Ni45Cu5 to fully utilize the material flexibility of the additive manufacturing process to develop ternary shape memory alloys. The chemical composition, phase, and material properties at multiple locations along the build direction were studied, using scanning electron microscopy, energy-dispersive X-ray spectroscopy, X-ray diffraction, Vickers hardness test-ing, tensile testing, and differential scanning calorimetry. The location-dependent compositions of martensitic TiNi and austenitic TiNi phases, mechanical properties, and functional properties …

Novel And Fast Peridynamic Models For Material Degradation And Failure, Siavash Jafarzadeh

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Fracture is one of the main mechanisms of structural failure. Corroded surfaces with chemically-induced damage are, notably, potential sites for crack initiation and propagation in metals, which can lead to catastrophic failure of structures. Despite some progress in simulating fracture and damage using classical models, realistic prediction of complex damage progression and failure has been out of reach for many decades. Peridynamics (PD), a nonlocal theory introduced in 2000, opened up new avenues in modeling material degradation and failure. Existing numerical methods used to discretize PD equations, however, are quite expensive as the PD nonlocal interactions make them unaffordable for …

Mash 2016 Test Level 3 And Test Level 4 Evaluation Of Roadside Safety Barrier With Pedestrian Features, Miguel Angel Hinojosa Palacios

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

The Minnesota Department of Transportation (MnDOT) desires to use a vehicle, bicycle, and pedestrian combination bridge railing system along pedestrian and bicycle bridge paths. The system was evaluated per MASH 2016.

In full-scale crash test no. MNPD-3, the system was evaluated according to MASH test designation no. 3-11. The 2014 Dodge Ram 1500 crew cab pickup truck impacted the system 71¼ in. upstream from the centerline of post no. 4 with a speed of 63.4 mph at an angle of 25.3 degrees. The combination railing system was found to meet the AASHTO MASH 2016 TL-3 impact safety criteria.

MnDOT uses …

Effects Of Air Pollution, Temperature And Moisture Content On Copper And Silver Corrosions And The Reliability Of Data Center Equipment, Rui Zhang

Dissertations - ALL

The effects of moisture content, temperature, and pollutant mixture on atmospheric corrosion of copper and silver were investigated by exposing test specimens to different environmental conditions, followed by surface characterization using the coulometric reduction, Scanning Electron Microscopy, and Energy Dispersive Spectrometry (SEM/EDS). Printed circuit board test cards (PCBs) with bare copper were also used to investigate the effects of voltage bias on the PCBs on the corrosion rate. The test specimens were exposed to mixed flowing gases (MFG) environment with eight different combinations of the following five pollutants at the fixed concentration levels: 60 ppb O3, 80 ppb NO2, 40 …

Effects Of Air Pollution, Temperature And Moisture Content On Copper And Silver Corrosions And The Reliability Of Data Center Equipment, Rui Zhang

Dissertations - ALL

The effects of moisture content, temperature, and pollutant mixture on atmospheric corrosion of copper and silver were investigated by exposing test specimens to different environmental conditions, followed by surface characterization using the coulometric reduction, Scanning Electron Microscopy, and Energy Dispersive Spectrometry (SEM/EDS). Printed circuit board test cards (PCBs) with bare copper were also used to investigate the effects of voltage bias on the PCBs on the corrosion rate. The test specimens were exposed to mixed flowing gases (MFG) environment with eight different combinations of the following five pollutants at the fixed concentration levels: 60 ppb O3, 80 ppb NO2, 40 …

Sound, Material And Strength Correlation, Ryan Mcbride

Symposium of Student Scholars

With a growing amount of manufacturing utilizing 3D printing, there is a correlation between strength and material which can affect sound produced by sirens. An air raid siren that has been downloaded from Thingiverse.com spins with a 49:1 gear ratio to produce 2 tone sounds and with that large number of revolutions comes friction, and in order to create a 3D printed air raid siren, the siren must be made out of a material that can withstand high temperatures without melting and quick rotations without delaminating. There are many materials that can be printed to withstand those forces, but it …

Open Source Vacuum Oven Design For Low-Temperature Drying: Performance Evaluation For Recycled Pet And Biomass, Benjamin R. Hubbard, Lindsay I. Putman, Stephen Techtmann, Joshua M. Pearce

Michigan Tech Publications, Part 1

Vacuum drying can dehydrate materials further than dry heat methods, while protecting sensitive materials from thermal degradation. Many industries have shifted to vacuum drying as cost-or time-saving measures. Small-scale vacuum drying, however, has been limited by the high costs of specialty scientific tools. To make vacuum drying more accessible, this study provides design and performance information for a small-scale open source vacuum oven, which can be fabricated from off-the-shelf and 3-D printed components. The oven is tested for drying speed and effectiveness on both waste plastic polyethylene terephthalate (PET) and a consortium of bacteria developed for bioprocessing of terephthalate wastes …

Computational Design Of Nonlinear Stress-Strain Of Isotropic Materials, Askhad M.Polatov, Akhmat M. Ikramov, Daniyarbek Razmukhamedov

Chemical Technology, Control and Management

The article deals with the problems of numerical modeling of nonlinear physical processes of the stress-strain state of structural elements. An elastoplastic medium of a homogeneous solid material is investigated. The results of computational experiments on the study of the process of physically nonlinear deformation of isotropic elements of three-dimensional structures with a system of one- and double-periodic spherical cavities under uniaxial compression are presented. The influence and mutual influence of stress concentrators in the form of spherical cavities, vertically located two cavities and a horizontally located system of two cavities on the deformation of the structure are investigated. Numerical …

Rehology And Electrical Conductivity Of Particulate Composites In Additive Manufacturing, Bin Xia

Mechanical Engineering Research Theses and Dissertations

Extrusion-based multi-functional additive manufacturing (AM) has been a rapidly developing area in AM recently. Particulate composites are widely used in this area to provide different functionalities with different types of particulate additives. However, there is no systematic understanding of the behavior of particulate composites during extrusion (especially in small nozzles) or of their properties once deposited in the build. This work investigates the properties of the type of particulate composites usually used in additive manufacturing, composed of a polymer matrix material and particulate additives within the micrometer scale. The focus is on the material rheology in the nozzle/capillary (for the …

Device Development For Long-Term Systemic Oral Biologic Drug Delivery, Benjamin Wankum

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

A biologic drug is a drug that is produced by a living organism. Biologic drugs are used to treat various medical conditions such as arthritis, diabetes, or certain forms of cancers due to their high potency and high selectivity of action. Drawbacks of biologics include their poor stability in the gastrointestinal tract and their poor absorption. In effect, this gives the drugs very low bioavailability and short therapeutic half-lives. To combat these obstacles, current delivery methods include subcutaneous injections at home or intravenous or intramuscular injections in a medical facility.

The overall scientific goal of the research was to utilize …

An Investigation Of Testing Parameters On The Frictional Properties Of Patterned Core-Shell Nanostructures, Colin Phelan

Graduate Theses and Dissertations

Friction tests are a beneficial means to analyze the tribological characteristics and advantages of materials and textured surfaces. However, the selected test parameters can significantly influence the results. This work explores the significance of the friction testing parameters on the frictional performances of core-shell nanostructure-textured surfaces (CSNTSs). Several applied normal loads (10 μN, 100 μN, and 500 μN) and diamond counterface indenter tip radii (1 μm, 5 μm, and 20 μm) were selected for the testing of Al/diamond-like-carbon (DLC) and Al/amorphous silicon (a-Si) CSNTSs. The measured friction values of the CSNTSs were then compared to a matching Al/DLC film and …

Characterizing High Entropy Alloys For Hypersonic Applications, Katherine Pettus

Mechanical Engineering Undergraduate Honors Theses

In this paper, the properties of a new and broad class of materials, high entropy alloys (HEAs), were investigated and evaluated for hypersonic applications. The plan was to identify candidate hypersonic HEAs and model the high-temperature strength using new advanced material models that account for asymmetry and anisotropy characterized with available test data. After accessing a local database of HEAs and their material properties in collaboration with Dr. Gorsse et al., it was realized the knowledge of HEAs is currently very broad but lacks depth. While hundreds of HEAs have been created and tested, none so far have both sufficient …

Noise Control In Sorting Conveyors, Eyra Herrera

Mechanical Engineering Undergraduate Honors Theses

E-commerce has increased the necessity of effective material handling equipment in warehouses and distribution centers. Sorter conveyors systems facilitate material handling by providing a reliable and automated system to classify and distribute products in a gentle and rapid manner. With the steady increase of speed in sorter conveyors to satisfy today’s industry demand, some systems have started to produce high noise levels that could potentially affect workers’ health. Since decreasing the speed of these conveyors is not a viable option to decrease noise in sorter equipment, industries have opted to find other ways to apply noise control to their equipment. …

Design And Control Of A Peristaltic Pump To Simulate Left Atrial Pressure In A Conductive Silicone Model, Jeremy Collins

Mechanical Engineering Undergraduate Honors Theses

According to the CDC, atrial fibrillation is responsible for more than 454,000 hospitalizations and approximately 158,000 deaths per year. A common treatment for atrial fibrillation is catheter ablation, a process in which a long flexible tube is guided through the femoral artery and to the source of arrhythmia in the heart, where it measures the electrical potential at various locations and converts problematic heart tissue to scar tissue via ablation. This paper details the design and control of a low-cost ($400) peristaltic pump system using repetitive control to replicate blood pressure in the left atrium in a conductive silicone model …

Development Of An Intraperitoneal Catheter Placement Device For Use On The Battlefield, Riley Reynolds

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

The objective of this project was to simplify peritoneal cavity access so an Airforce field medic can safely infuse oxygen microbubbles (OMBs) into the intraperitoneal space for the emergency treatment of hypoxia due to lung damage. To solve this problem, we created an intraperitoneal catheter placement device for use on the battlefield. The three common methods and some of the most common devices for peritoneal cavity access were reviewed. Injury frequencies for each of the three methods were analyzed. The results showed that each of the access techniques gives a similar rate of iatrogenic injury.

The battlefield conditions where the …

Performance And Economics Of Solar Inverters And Module Level Power Electronics In A 1 Mw Photovoltaic System, Maxwell Criswell

Biological and Agricultural Engineering Undergraduate Honors Theses

Photovoltaic solar panels convert sunlight to electricity in the form of direct current; therefore, a necessary component of every photovoltaic system is an inverter to convert the electricity to usable alternating current. There are various commercially available inverter technologies manufactured today such as microinverters, string inverters, and central inverters, as well as module level power electronic devices such as DC optimizers that are capable of improving system performance in string and central inverter systems. This thesis compares the performance and economics of five different inverter and module level power electronic systems through model simulation using Helioscope software. The five alternatives …

First-Principles Studies Of Nucleation Of Atomic-Layered Molybdenum Disulfide By Atomic Layer Deposition, Matthew Lawson

Boise State University Theses and Dissertations

This dissertation implements first-principles calculations to understand the nucleation mechanisms for atomic layer deposition (ALD) of molybdenum disulfide (MoS₂) using MoF₆ and H₂S precursors. ALD is a self-limiting process that can deposit a range of materials at the nanoscale, while maintaining chemical stoichiometry, atomic scale thickness control, and can conform to high-aspect ratio substrate designs. ALD is extremely sensitive to surface chemistry and morphology; therefore, it is critical to understand how these factors control deposition.

Density functional theory (DFT) was used to understand what factors can control the nucleation for ALD of MoS₂ using …

A Hyperelastic Porous Media Framework For Ionic Polymer-Metal Composites And Characterization Of Transduction Phenomena Via Dimensional Analysis And Nonlinear Regression, Zakai J. Olsen

UNLV Theses, Dissertations, Professional Papers, and Capstones

Ionic polymer-metal composites (IPMC) are smart materials that exhibit large deformation in response to small applied voltages, and conversely generate detectable electrical signals in response to mechanical deformations. The study of IPMC materials is a rich field of research, and an interesting intersection of material science, electrochemistry, continuum mechanics, and thermodynamics. Due to their electromechanical and mechanoelectrical transduction capabilities, IPMCs find many applications in robotics, soft robotics, artificial muscles, and biomimetics. This study aims to investigate the dominating physical phenomena that underly the actuation and sensing behavior of IPMC materials. This analysis is made possible by developing a new, hyperelastic …