Mechanical Engineering Commons^™

Design And Numerical Simulation Of Two Dimensional Ultra Compact Combustor Model Sections For Experimental Observation Of Cavity-Vane Flow Interactions, David S. Moenter

Theses and Dissertations

An improved computational fluid dynamics (CFD) model was developed for numerical simulation of the Ultra Compact Combustor (UCC) concept to enhance turbulent flow characterization of the circumferentially traveling, centrifugal-force enhanced combustion, cavity flow into the engine main flow passage via a radial cavity in the turbine axial guide vanes. The CFD model uses a dense grid on a 60° periodic, axisymmetric combustor section, with the RNG κ-ε turbulence model to resolve turbulent flow details. An overall analysis and performance evaluation of the experimentally tested UCC configuration and an axially shortened cavity baseline configuration was conducted at various experimentally documented operating …

High Temperature Heat Exchanger Project: Quarterly Progress Report April 1, 2006 Through June 30, 2006, Anthony Hechanova

Publications (NSTD)

Numerical Analyses of the Ceramatec Sulfuric Acid Decomposer. Comparisons with experiments for the Ceramatec sulfuric acid decomposer coupon with eight straight channels for four different geometries and four different flow rates were performed. All of the operation and boundary conditions for the calculations were the same as in the Ceramatec experiments. Good agreement was found. The overall pressure drop difference between calculations and experiments for most of the cases is within 10%.

Non-Isothermal Reaction-Diffusion Systems With Thermodynamically Coupled Heat And Mass Transfer, Yaşar Demirel

Papers in Analytical Chemistry

Non-isothermal reaction-diffusion (RD) systems control the behavior of many transport and rate processes in physical, chemical, and biological systems. A considerable work has been published on mathematically coupled nonlinear differential equations of RD systems by neglecting the possible thermodynamic couplings among heat and mass fluxes, and reaction velocities. Here, the thermodynamic coupling refers that a flux occurs without its primary thermodynamic driving force, which may be gradient of temperature, or chemical potential, or reaction affinity. This study presents the modeling equations of non-isothermal RD systems with coupled heat and mass fluxes excluding the coupling of chemical reactions using the linear …

High Temperature Heat Exchanger Project: Quarterly Progress Report January 1, 2006 Through March 31, 2006, Anthony Hechanova

Publications (NSTD)

Quarterly Collaboration Meeting. The UNLVRF HTHX Project quarterly meeting was held in Albuquerque, NM, March 16 and 17, 2006. The purpose of the meeting was to promote collaboration and communication among the UNLV Research Foundation partners. A tour of Sandia National Laboratory was also provided that included a visit to their sulfuric acid decomposition test apparatus. There were 24 attendees from universities, national laboratories, and private industry. Collaborators discussed their research progress. The next meeting will be in July in Salt Lake City, UT.

Unlv Research Foundation High Temperature Heat Exchanger Development, Anthony Hechanova

Publications (NSTD)

Barriers addressed:

Nuclear Hydrogen Initiative R&D Plan – Material performance and component design and testing for: intermediate heat exchanger and high-temperature thermochemical water splitting (H2SO4 decomposition and HI decomposition). Improved materials for High Temperature Electrolysis.

Retrofit Of Distillation Columns Using Thermodynamic Analysis, Yaşar Demirel

Papers in Physical Properties

Thermodynamic analysis provides the column grand composite curves and exergy loss profiles, which are becoming readily available for a converged distillation column simulation. For example, the Aspen Plus simulator performs the thermodynamic analysis through its Column–Targeting tool for rigorous column calculations. This study uses the column grand composite curves and the exergy loss profiles obtained from Aspen Plus to assess the performance of the existing distillation columns, and reduce the costs of operation by appropriate retrofits in a methanol plant. Effectiveness of the retrofits is also assessed by means of thermodynamics and economics. The methanol plant utilizes two distillation columns …

Numerical Investigation Of Cavity-Vane Interactions Within The Ultra Compact Combustor, Jonathan F. Anisko

Theses and Dissertations

A numerical analysis and design optimization of the Ultra Compact Combustor (UCC) has been conducted. The UCC is a combustor designed to incorporate high-g loadings to increase flame propagation speed while reducing flame length, thereby helping to significantly reduce the size of a combustor. A commercial CFD package with a k-Ⲉ turbulence model has been used to develop design rules for the construction of future UCCs. There have been several versions of UCC that have been designed, built and tested by AFRL/PRTC. Since real experimental tests are expensive and construction time is prohibitive to test many different design configurations, CFD …

Effect Of Gravity On Methanol Diffusion Flames Burning Within A Forced Convective Environment, V. Raghavan, G. Gogos, V. Babu, T. Sundararajan

Combustion Research at University of Nebraska-Lincoln

Effect of Gravity on Methanol Diffusion Flames Burning within a Forced Convective Environment

Optimization Of A Low Heat Load Turbine Nozzle Guide Vane, Jamie J. Johnson

Theses and Dissertations

Often turbomachinery airfoils are designed with aerodynamic performance foremost in mind rather than component durability. However, future aircraft systems require ever increasing levels of gas-turbine inlet temperature causing the durability and reliability of turbine components to be an ever more important design concern. As a result, the need to provide improved heat transfer prediction and optimization methods presents itself. Here, an effort to design an airfoil with minimized heat load is reported. First, a Reynolds-Averaged Navier-Stokes (RANS) flow solver was validated over different flow regimes as well as varying boundary conditions against extensive data available in literature published by the …

Design, Build And Validation Of A Small-Scale Combustion Chamber Testing Facility, Eric R. Dittman

Theses and Dissertations

This study investigated the design parameters necessary for the construction and use of a testing facility built to test the combustor section of engines. User inputs were acquired by interview and used in the decisions made in arrangement of pieces of machinery and how different systems were to interact. The design was then carried out as the various parts of the facility were built and installed. Software was designed which controlled the different parts of the combustion process and monitored the different products of combustion as well as the properties of the air and fuel used in the combustion. These …

Effects Of Forced Convection And Surface Tension During Methanol Droplet Convection,”, V. Raghavan, D. N. Pope, G. Gogos

Combustion Research at University of Nebraska-Lincoln

Effects of Forced Convection and Surface Tension during Methanol Droplet Convection,”

Numerical Simulation Of Fuel Droplet Extinction Due To Forced Convection,", D. N. Pope, G. Gogos

Combustion Research at University of Nebraska-Lincoln

Numerical Simulation of Fuel Droplet Extinction Due to Forced Convection,"

A New Multicomponent Diffusion Formulation For The Finite-Volume Method: Application To Convective Droplet Combustion, D. N. Pope, G. Gogos

Combustion Research at University of Nebraska-Lincoln

A New Multicomponent Diffusion Formulation for the Finite-Volume Method: Application to Convective Droplet Combustion

Combustion Of Moving Droplets And Suspended Droplets: Transient Numerical Results, D. N. Pope, D. Howard, K. Lu, G. Gogos

Combustion Research at University of Nebraska-Lincoln

Combustion of Moving Droplets and Suspended Droplets: Transient Numerical Results

Surface Tension Effects During Low Reynolds Number Methanol Droplet Combustion, V. Raghavan, D. N. Pope, D. Howard, G. Gogos

Combustion Research at University of Nebraska-Lincoln

Surface Tension Effects during Low Reynolds Number Methanol Droplet Combustion

Thermally Developing Flow And Heat Transfer In Rectangular Microchannels Of Different Aspect Ratios, Poh-Seng Lee, S V. Garimella

CTRC Research Publications

Laminar convective heat transfer in the entrance region of microchannels of rectangular cross-section is investigated under circumferentially uniform wall temperature and axially uniform wall heat flux thermal boundary conditions. Three-dimensional numerical simulations were performed for laminar thermally developing flow in microchannels of different aspect ratios. Based on the temperature and heat flux distributions obtained, both the local and average Nusselt numbers are presented graphically as a function of the dimensionless axial distance and channel aspect ratio. Generalized correlations, useful for the design and optimization of microchannel heat sinks and other microfluidic devices, are proposed for predicting Nusselt numbers. The proposed …

High Temperature Heat Exchanger Project: Quarterly Progress Report October 1, 2005 Through December 31, 2005, Anthony Hechanova

Publications (NSTD)

• Liquid Salt Technical Working Group Meeting. The first meeting of the Liquid Salt Technical Working Group was held on October 28, 2005 at the Pratt Whitney Rocketdyne facility in Canoga Park, CA. 20 experts from academia, industry, and national laboratories participated to discuss current state of knowledge and research needs for high temperature liquid salt applications.
• Nuclear Hydrogen Initiative Semi-annual Review. Several participants from the UNLVRF University Consortium gave technical presentations at the NHI Semi-annual Review meeting in Rockville, MD, November 9-10, 2005.
• Quarterly Collaboration Meeting. The University of Nevada, Las Vegas hosted a UNLVRF HTHX Project quarterly meeting December …

Application Of An Hp-Adaptive Finite Element Method For Thermal Flow Problems, Xiuling Wang, Darrell Pepper

Mechanical Engineering Faculty Research

Numerical results are presented for a set of convective thermal flow problems using an hp-adaptive finite element technique. The hp-adaptive model is based on mesh refinement and spectral order incensement to produce enhanced accuracy while attempting to minimize computational requirements. An a-posteriori error estimator based on the L₂ norm is employed to guide the adaptation procedure. Example test cases consisting of natural convection in a differentially heated enclosure, flow with forced convection heat transfer over a backward facing step and natural convection within an enclosed partition are presented. Numerical results are compared with published data in the …

Cool Flames At Terrestrial, Partial, And Near-Zero Gravity, Michael R. Foster, Howard Pearlman

Faculty Publications - Biomedical, Mechanical, and Civil Engineering

Natural convection plays an important role in all terrestrial, Lunar, and Martian-based, unstirred, static reactor cool flame and low-temperature autoignitions, since the Rayleigh number (Ra) associated with the self-heating of the reaction exceeds the critical Ra (approximately 600) for onset of convection. At near-zero gravity, Ra < 600 can be achieved and the effects of convection suppressed. To systematically vary the Ra without varying the mixture stoichiometry, reactor pressure, or vessel size, cool flames are studied experimentally in a closed, unstirred, static reactor subject to different gravitational accelerations (terrestrial, 1g; Martian, 0.38g; Lunar, 0.16g; a n dr e - duced gravity, ∼10−2g). Representative results show the evolution of the visible light emission using an equimolar n-butane:oxygen premixture at temperatures ranging from 320 to 350 ◦C (593–623 K) at subatmospheric pressures. For representative reduced-gravity, spherically propagating cool flames, the flame radius based on the peak light intensity is plotted as a function of time and the flame radius (and speed) is calculated from a polynomial fit to data. A skeletal chemical kinetic Gray-Yang model developed previously for a one-dimensional, reactive– diffusive system by Fairlie and co-workers is extended to a two-dimensional axisymmetric, spherical geometry. The coupled species, energy, and momentum equations are solved numerically and the spatio-temporal variations in the temperature profiles are presented. A qualitative comparison is made with the experimental results.

Transient Heat Partition Factor For A Sliding Railcar Wheel, T C. Kennedy, C Plengsaard, Robert F. Harder

Faculty Publications - Biomedical, Mechanical, and Civil Engineering

During a wheel slide the frictional heat generated at the contact interface causes intense heating of the adjacent wheel material. If this material exceeds the austenitising temperature and then cools quickly enough, it can transform into martensite, which may ultimately crack and cause wheel failure. A knowledge of the distribution of the heat partitioned into the wheel and the rail and the resulting temperature fields is critical to developing designs to minimize these deleterious effects. A number of theoretical solutions have appeared in the literature to model the thermal aspects of this phenomenon. The objective of this investigation was to …

Including Embodied Energy Considerations At The Conceptual Stage Of Building Design, Y. Yohanis, Brian Norton

Articles

Elevated operating temperatures reduce the solar to electrical conversion efficiency of building integrated photovoltaic devices (BIPV). Phase change materials (PCM) can be used to passively limit this temperature rise although their effectiveness is limited by their low thermal conductivities and by crystallization segregation during solidification. This paper presents an experimental evaluation of the effects of convection and crystalline segregation in a PCM as a function of efficiency of heat transfer within the finned PV/PCM system. The thermal performances of bulk PCM with crystallization segregation for different internal fin arrangements are presented. It is noted that the addition of internal fins …

Magnetohydrodynamic Simulation Of Electromagnetic Pump In Tc-1, Lillian J. Ratliff

Reactor Campaign (TRP)

The pilot molten lead-bismuth target circuit (TC-1) in university of Nevada Las Vegas (UNLV) was designed for beam power of 1 MW accelerator driven system (ADS). The TC-1 is a liquid lead-bismuth eutectic (LBE) circulation loop. Circulation of the liquid alloy is driven by an annular linear induction pump (ALIP). Experimental measurements of system parameters have yielded a surprisingly low pump efficiency of less than 1%. A numerical study of the pump efficiency is being conducted to determine which operational parameters are responsible for this low efficiency and to give insight into future EM pump design. The numerical study will …

Performance Measurements Of Direct Air Injection In A Cavity-Based Flameholder For A Supersonic Combustor, Scott G. Edens

Theses and Dissertations

For several years the Air Force Research Lab Propulsion Directorate has been studying the difficulties in fueling supersonic combustion ramjet engines with hydrocarbon based fuels. Recent investigations have focused on the use of direct air injection into a directly-fueled cavity-based flameholder. Direct air injection has been shown qualitatively to be a valuable tool for improving cavity combustion. Little quantitative data is available that characterizes the performance of cavity-based flameholders. The objective of this research was to quantitatively determine the specific advantages and disadvantages of the direct air injection scheme. This was accomplished via intrusive probing into a supersonic free stream …

High Temperature Heat Exchanger Project: Quarterly Progress Report July 1, 2005 Through September 30, 2005, Anthony Hechanova

Publications (NSTD)

Quarterly Collaboration Meeting. The University of California, Berkeley, hosted a UNLVRF HTHX Project quarterly meeting on September 12. The purpose of the meeting was to promote collaboration and communication among the UNLV Research Foundation partners. Collaborators discussed their research program plan and provided an update on their progress. The next meeting will be in December in Las Vegas, NV hosted by UNLV.

High Temperature Heat Exchanger Project: Quarterly Progress Report April 1, 2005 Through June 30, 2005, Anthony Hechanova

Publications (NSTD)

Quarterly Collaboration Meeting. General Atomics hosted a UNLVRF HTHX Project quarterly meeting on June 5 in San Diego, California. The purpose of the meeting was to promote collaboration and communication among the UNLV Research Foundation partners. Collaborators had the opportunity to discuss their research program plan and update their progress. The next meeting will be in September in Berkeley hosted by UC Berkeley.

HTHX Computational Design (UNLV). Work on optimizing the ceramic offset strip in compact HTHX design through parametric studies was performed and completed. A simple single channel model was used to perform parametric studies on dimensions and flow …

Stability Of Transport And Rate Processes [Review], Yaşar Demirel

Papers in Thermal Mechanics

About fifty years ago, the Turing instability demonstrated that even simple reaction-diffusion systems might lead to spatial order and differentiation, while the Rayleigh-Bénard instability showed that the maintenance of nonequilibrium might be the source of order in fluids subjected to a thermodynamic force above a critical value. Therefore, distance from global equilibrium in the form of magnitude of a thermodynamic force emerges as another constraint of stability; some systems may enhance perturbations, and evolve to highly organized states called the dissipative structures after a critical distance on the thermodynamic branch. Although the kinetics and transport coefficients represent short-range interactions, chemical …

Mercury Experience And Capabilities, University Of North Dakota. Energy And Environmental Research Center

EERC Brochures and Fact Sheets

Brochure about the Energy & Environmental Research Center’s (EERC’s) mercury research capabilities. Describes the EERC facilities and mercury testing technology. [This item is an outdated or superseded version and retained for historical purposes only. It may no longer reflect current information, policies, or practices.]

A Novel Hybrid Heat Sink Using Phase Change Materials For Transient Thermal Management Of Electronics, Shankar Krishnan, S V. Garimella, S. S. Kang

CTRC Research Publications

A hybrid heat sink concept which combines passive and active cooling approaches is proposed. The hybrid heat sink is essentially a plate fin heat sink with the tip immersed in a phase change material (PCM). The exposed area of the fins dissipates heat during periods when high convective cooling is available. When the air cooling is reduced, the heat is absorbed by the PCM. The governing conservation equations are solved using a finite-volume method on orthogonal, rectangular grids. An enthalpy method is used for modeling the melting/re-solidification phenomena. Results from the analysis elucidate the thermal performance of these hybrid heat …

Induction Heating Of Thin Films, Paul L. Bergstrom, Melissa L. Trombley

Michigan Tech Patents

A method of performing regional heating of a system having a substrate. The method may include applying a thin film to the system, and controllably energizing a coil positioned near the thin film. The energized coils thereby generate a magnetic flux. The method further includes inducing a current in the thin film with the magnetic flux thereby heating the system.

High Temperature Heat Exchanger Project:Quarterly Progress Report January 1, 2005 Through March 31, 2005, Anthony Hechanova

Publications (NSTD)

Quarterly Collaboration Meeting. Ceramatec, Inc. hosted a UNLVRF HTHX Project quarterly meeting on March 17 in Salt Lake City, Utah. The purpose of the meeting was to promote collaboration and communication among the UNLV Research Foundation partners. Collaborators had the opportunity to discuss their research program plan and update their progress. The next meeting will be in June in San Diego City hosted by General Atomics.