Mechanical Engineering Commons^™

Go With The Flow –Thermoelectric Energy, Shawn Bell

Middle School Lesson Plans

In this unit, students will learn how thermal energy be transferred and transformed. They will carry out investigations to gather evidence to support an explanation about direct conversion of heat into electrical energy. They will develop a model that shows the components of the system and changes in the system being investigated, and they will use evidence from the investigation to construct an explanation for how the energy flows.

Significance Of Parameters Affecting The Performance Of A Passive Down-Draft Evaporative Cooling (Pdec) Tower With A Spray System, Daeho Kang, Richard K. Strand

Publications and Research

PDEC towers with spray systems are known to achieve substantial energy savings. Various parameters such as the wet-bulb depression, the tower height, and the wind speed have been known to be key factors affecting the performance of the system. To date, the significance of these parameters and other important factors have not been adequately treated in the literature. There also has been a lack of models that can successfully investigate potential benefits of the system under various conditions where this particular system could be applicable. To address these critical issues, this study performed a parametric analysis by using a FLUENT …

Fluid Analysis In Solar Heat Pipes, Ben Krumholz, Michael Agavo, William Dundon

Mechanical Engineering

Evacuated tube solar collectors are efficient systems that use heat pipes to facilitate heat transfer. They use incoming solar radiation to heat water. Professor Mason Medizade tasked the team with choosing a component of the system to research and test its influence on system performance. The team investigated the working fluid that runs through the heat pipes. Distilled water, acetone, and ethanol at a range of fill volumes form 1 mL to 11 mL were tested. The team's goal was to find a volume for each fluid to maximize performance of the system. Performance was defined as average temperature rise …

Me 350 Air Conditioning Experiment, Joshua Baida, Ellie Hallner, Tyler Eschenbach

Mechanical Engineering

In keeping with Cal Poly's focus on physically applying the concepts learned in the classroom, our team of engineering students has compiled a laboratory experiment displaying the basic thermodynamic cycle found in air conditioning systems. This vapor compression cycle is displayed on a visualization board that features all four major components of the system: the compressor, the evaporator, the condenser, and the throttling valve. Students will take measurements of temperature and pressure at each stage in the cycle and also gauge the power draw from the compressor to gain an understanding of how performance and electricity cost come into play …

Micro Debris Generator, Gordan Bradaric, Ross Byers, Stephen Quanci

Mechanical Engineering

This senior project team at Cal Poly consisting of Stephen Quanci, Gordan Bradaric, and Ross Byers has been commissioned by Erik Brown of Lawrence Livermore National Labs to create a way to reliably and consistently entrain microscopic particles into the hot HTTU flow. These particles will be used to compare the loading rates of new HEPA filters by measuring the pressure drop across the filter. The generated particles would simulate typical conditions in which these HEPA filters are expected to operate, namely fine ash. The particles used for loading the filter are intended to simulate the particulate reaching the LLNL …

Investigation Of Thermal Scaling Effects For A Turbine Blade Leading Edge And Pressure Side Model, Ryan A. Lynch

Theses and Dissertations

Recent experiments have attempted to quantify the overall cooling effectiveness at elevated temperature conditions. The Film Cooling Rig (FCR) at the Air Force Institute of Technology has been modified to better match the configuration of a similar large scale, low temperature rig at the Air Force Research Laboratory. This has enabled comparison and trend identification of how various properties scale from the low to high temperature condition. Various internal cooling and hole geometry configurations were investigated over a range of temperatures while utilizing the thermal scaling capability of Inconel 718. Film cooling trends and measures of overall effectiveness were matched, …

Efficiency Testing Of An Electronic Speed Controller, Grace Cowell, Matthew Hudson, Marcus Pereira

Mechanical Engineering

This project required the development of a rig that could experimentally determine the efficiency of an Electronic Speed Controller (ESC). The selected design focuses on measuring the losses due to heat from the device and comparing this to its input power. The selected design is a flow rig that utilizes the heat equation q=ṁcpΔT. The rig provides a steady state measurement of the ESC heat output by passing a known mass flow rate of air across the ESC and measuring the temperature difference. It uses a flowmeter to determine ṁ, thermocouples to determine ΔT, and a table lookup to determine …

A Study Of Constant Voltage Anemometry Frequency Response, Alex D. Powers

Master's Theses

The development of the constant voltage anemometer (CVA) for the boundary layer data system (BLDS) has been motivated by a need for the explicit autonomous measurement of velocity fluctuations in the boundary layer. The frequency response of a sensor operated by CVA has been studied analytically and experimentally. The thermal lag of the sensor is quantified by a time constant, M_CVA. When the time constant is decreased, the half-amplitude cut-off frequency, f_CVA, is increased, thereby decreasing the amount of attenuation during measurements. In this thesis, three main approaches have been outlined in theory and tested experimentally …

Continuum Modeling Of The Densification Of W-Ni-Fe During Selective Laser Sintering, Connor M. West

Master's Theses

The purpose of this thesis is to effectively model the time history of the temperature distribution during the selective laser sintering process and use this information to investigate the resulting relative density. The temperature is a critical parameter of the process because it directly effects the overall quality of the part. First, an efficient, affordable, and reliable simulation was developed within the finite element software, Abaqus. Next, the results from the simulations were compared to the experimental results performed by Wang et al. (2016). The FEA model consisted of a 3 layer simulation. Multiple simulations at various laser recipes were …

A Numerical Study Of Compressible Lid Driven Cavity Flow With A Moving Boundary, Amer Hussain

LSU New Orleans Theses and Dissertations

A two-dimensional (2-D), mathematical model is adopted to investigate the development of circulation patterns for compressible, laminar, and shear driven flow inside a rectangular cavity. The bottom of the cavity is free to move at a specified speed and the aspect ratio of the cavity is changed from 1.0 to 1.5. The vertical sides and the bottom of the cavity are assumed insulated. The cavity is filled with a compressible fluid with Prandtl number, Pr =1. The governing equations are solved numerically using the commercial Computational Fluid Dynamics (CFD) package ANSYS FLUENT 2015 and compared with the results for the …

Effect Of Non-Uniform Air-Side Velocity Distribution On Heat Transfer Model Predictions For Microchannel Condenser., Zachary Chapin

Electronic Theses and Dissertations

This is a study of the effects on heat transfer capacity predictions of microchannel condensers when airflow is maldistributed due to the shape of the condenser. The three shapes investigated in this study are flat, U-shape and roll. Each coil was tested in a water calorimeter and those results were compared to the model prediction. The model prediction was calculated using CoilDesigner™ modeling software with standard correlations. Using the uniform airflow assumption, the model over predicted the heat capacity measured in the calorimeter by 5-11% depending on the coil and inlet conditions. The local airflow velocity was measured using a …

Leidenfrost Energy Barriers, James Peck, Anton Hassebrook, Craig Zuhlke, Troy P. Anderson, Dennis R. Alexander, George Gogos, Sidy Ndao

UCARE: Research Products

In this work, an “Energy Barrier” was created to control the motion of Leidenfrost droplets. This barrier was created by functionalizing a portion of a mirror-polished stainless steel 304 surface with Femtosecond Laser Surface Processing (FLSP). FLSP results in superhydrophilic, hierarchical, micro- and nanostructures which are highly wetting and thus have an increased Leidenfrost temperature. Water droplets in the film boiling state were deposited, and propelled by gravity towards the Energy Barrier interface. Room temperature droplets were deposited over a range of surface temperatures beginning with the Leidenfrost temperature of mirror-polished stainless steel 304 and culminating at the Leidenfrost temperature …

Method For Determining Time-Resolved Heat Transfer Coefficient And Adiabatic Effectiveness Waveforms With Unsteady Film Cooling, James L. Rutledge, Jonathan F. Mccall

AFIT Patents

A new method for determining heat transfer coefficient (h) and adiabatic effectiveness (η) waveforms h(t) and η(t) from a single test uses a novel inverse heat transfer methodology to use surface temperature histories obtained using prior art approaches to approximate the h(t) and η(t) waveforms. The method best curve fits the data to a pair of truncated Fourier series.

Heating Element Including Carbon Nanotube (Cnt) Layer, Santhosh Kumar Loganathan, Virginie Rollin, Daewon Kim

Publications

Apparatus , materials , and techniques and techniques herein can include providing a deposited layer comprising a com posite material including carbon nanotubes ( CNTs ) . Accord ing to various examples , the composite can be applied to a substrate such as using a solution containing CNTs and other constituents such as sulfur . The solution can be spray applied to a substrate , or spin - coated upon a substrate , such as to provide a uniform , conductive , and optically - transpar ent film layer . In one application , such a film layer can be …

Modeling Of Methane Tank Depressurization In Cold Weather, Brittney Bridger-Burton, Kevin D. Cole

UCARE: Research Products

Non-metallic tanks are used in industry to store and transfer gasses such as methane. As the tanks are emptied, the properties of the gas change, causing heat transfer with the tank wall. When emptied while at low temperatures, liquid condensation can form and the tank lining can reach a critically low temperature, causing fracture to the tank wall. In this study, the emptying of methane in cold weather conditions from a non-metallic tank was modelled using Aspen Tech Software. A full tank of methane, at 250 bar and 288 K, was cooled to the following starting temperatures: 263, 253, 243, …

Oscillatory Flow Mechanism For Enhanced Heat Transfer, Sultan Taher Raml

Doctoral Dissertations and Master's Theses

This research project is about the use of an oscillatory flow mechanism to enhance heat transfer. The idea behind this is to induce oscillation of the end wall of one of two connected chambers of a heat exchanger which effectively will induce oscillation of the boundary layer within the connecting duct. The main idea of this thesis came from using species separation studies before 40 years ago in hyperventilation technology to help patients under anesthesia in hospitals. There are many applications for this research such as removing heat from chemical reactors, electrical devices and other enclosed environments such as submarines, …

Application Of A Multi-Zone Model For The Prediction Of Species Concentrations In Rapid Compression Machine Experiments, David Wilson

Master's Theses (2009 -)

Accurate chemical kinetic models, which predict species evolution and heat release rates in chemically reactive systems, are essential for further advancements in fuel and combustion technology. An experimental facility that is widely used for evaluating the accuracy of kinetic models is a rapid compression machine (RCM), which creates a well-defined reaction environment by compressing a reactive mixture inside a chamber. Generally, RCM experiments are conducted in order to obtain ignition delay data. However, chemical speciation data provides greater insight into reaction pathways, and is therefore a more rigorous benchmark for validating kinetic models. In order for a chemical kinetic model …

Notes On Contributions To The Science Of Rare Earth Element Enrichment In Coal And Coal Combustion Byproducts, James C. Hower, Evan J. Granite, David B. Mayfield, Ari S. Lewis, Robert B. Finkelman

Center for Applied Energy Research Faculty and Staff Publications

Coal and coal combustion byproducts can have significant concentrations of lanthanides (rare earth elements). Rare earths are vital in the production of modern electronics and optics, among other uses. Enrichment in coals may have been a function of a number of processes, with contributions from volcanic ash falls being among the most significant mechanisms. In this paper, we discuss some of the important coal-based deposits in China and the US and critique classification systems used to evaluate the relative value of the rare earth concentrations and the distribution of the elements within the coals and coal combustion byproducts.

Effect Of Spalled Particles Thermal Degradation On A Hypersonic Flow Field Environment, Raghava S. C. Davuluri, Huaibao Zhang, Alexandre Martin

Mechanical Engineering Faculty Publications

Two-way coupling is performed between a spallation code and a hypersonic aerothermodynamics CFD solver to evaluate the effect of spalled particles on the flow field. Time accurate solutions are computed in argon and air flow fields. A single particle simulations and multiple particles simulations are performed and studied. The results show that the carbon vapor released by spalled particles tend to change the composition of the flow field, particularly the upstream region of the shock.

Performance Evaluation Of Palm Oil-Based Biodiesel Combustion In An Oil Burner, Abdolsaeid Ganjehkaviri, Mohammad Nazri Mohd Jaafar, Seyed Ehsan Hosseini, Anas Basri Musthafa

Faculty Publications - Mechanical Engineering

This paper presents an experimental investigation of the combustion characteristics of palm methyl ester (PME), also known as palm oil-based biodiesel, in an oil burner system. The performance of conventional diesel fuel (CDF) and various percentages of diesel blended with palm oil-based biodiesel is also studied to evaluate their performance. The performance of the various fuels is evaluated based on the temperature profile of the combustor's wall and emissions, such as nitrogen oxides (NOx) and carbon monoxide (CO). The combustion experiments were conducted using three different oil burner nozzles (1.25, 1.50 and 1.75 USgal/h) under lean (equivalence ratio (φ) = …

Phase Change Materials-Assisted Heat Flux Reduction: Experiment And Numerical Analysis, Hussein J. Akeiber, Seyed Ehsan Hosseini, Mazlan A. Wahid, Hasanen M. Hussen, Abdulrahman Th Mohammad

Faculty Publications - Mechanical Engineering

Phase change materials (PCM) in the construction industry became attractive because of several interesting attributes, such as thermo-physical parameters, open air atmospheric condition usage, cost and the duty structure requirement. Thermal performance optimization of PCMs in terms of proficient storage of a large amount of heat or cold in a finite volume remains a challenging task. Implementation of PCMs in buildings to achieve thermal comfort for a specific climatic condition in Iraq is our main focus. From this standpoint, the present paper reports the experimental and numerical results on the lowering of heat flux inside a residential building using PCM, …

Experimental Study Of The Flow Of Ferrofluid In A Porous Media Under A Magnetic Field, Muskaan Khurana

Dissertations, Master's Theses and Master's Reports

This research presents results from a laboratory-scale experimental setup that was designed to visualize the behavior of ferrofluid percolation through a porous media. Ferrofluids are colloidal suspensions made of magnetic particles of a few nanometers and stabilized in carrier liquids like water or mineral oil. Ferrofluids get magnetized and align themselves in the direction of a magnetic field when a field gradient is applied.

With the help of this experiment we investigate the viability of controlling fluid flow in porous medium by a magnetic field in vicinity. The experiments show that ferrofluids can be used as a transporting media to …

Solar Thermal Collector, Hazel Tickner, Tyson Nakamura

All Undergraduate Projects

During the course of this project, a solar thermal collector and supporting stand were designed and manufactured to be used during Mechanical Engineering Technology labs. Students will be able to use the collector to heat water, with the sun being the only heat source. The collector was designed by calculating surface area limitations, estimated solar input, and desired efficiency, to find the required water flow rate. From there, the necessary pipe lengths and diameters were determined, and the solar thermal collector was constructed. Two pipe paths were manufactured: a curved path, and a manifold path. Students will be able to …

Oscillating Heat Pipe Performance With Evaporator Section Modifications, Mitchell Hoesing

Electronic Theses and Dissertations

The continuous development of electronic components to become faster and smaller has led to an increasing problem with thermal management. Thermal management ensures that the component operating temperatures are within a safe range, which maintains performance and improves reliability and lifespan. Traditional thermal management devices, such as the extruded-fin heat sink, are incapable of maintaining the safe operating temperature range for current and future high heat flux cooling applications. A device that has the capability to meet this growing need is the oscillating heat pipe. Oscillating heat pipes (OHPs) are passive, two-phase cooling devices that have been shown to transfer …

Shear Driven Suppressed Nucleation Annular Flow-Boiling In Millimeter-Scale Channels: Direct Numerical Simulations, Sharayu Bhasme

Dissertations, Master's Theses and Master's Reports

Many contemporary high heat-flux cooling applications are facilitated by mm-scale flow-boilers that operate in the steady annular suppressed nucleation regime (i.e., a thin evaporating liquid film flow covers the heated boiling-surface).

For such cases, this thesis presents a direct numerical simulation (DNS) approach. The steady algorithm and its accuracy are discussed. Representative detailed solutions for annular flow-boiling of FC-72 in a horizontal channel are presented.

An Experimental Investigation Of Heat Transfer For Arrays Of Impingement Jets Onto The Featured Surfaces With Cylindrical And Elliptical Raised Surfaces, Marc A. Medina

Honors Undergraduate Theses

This study focuses on multi-jet impingement for gas turbine geometries in which the objective is to understand the influence of the roughness elements on a target surface to the heat transfer. Current work has proven that implementing roughness elements for multi-jet impingement target surfaces has increased heat transfer ranging anywhere from 10-30%. This study has chosen to investigate three different roughness elements, elliptical in cross-section, to compare to smooth surface geometries for multi-jet impingement. An experimental was taken for this study to extend the current knowledge of multi-jet impingement geometries and to further understand the heat transfer performance. A temperature …

Energy Resources Use Metrics, Rahul Y. Nehete

Theses and Dissertations--Mechanical and Aerospace Engineering

Energy resources use has been considered as a key component of sustainable development. Data related to global, regional, state, sector, industry and process demonstrate that a significant reduction of energy resources for a given production rate in manufacturing processes requires an introduction of transformational technologies at the process level, propagating the impact to higher scales, leading not just to a gradual improvement of traditional technologies but to more sustainable development.

The study offers two approaches to the formulation of the limits of energy use in the context of sustainable development. The first is to construct a map of key selected …

Flow Visualization Of Buoyant Instability In A Cross-Flow: An Implication For Flame Spread Over Forest Fuel Beds, Nikolay Gustenyov

Theses and Dissertations--Mechanical and Aerospace Engineering

This thesis reports small-scale laboratory experiments designed to visualize the flow over a heated plate. A low-speed wind tunnel was built, and a heating plate was flush mounted on the wind tunnel floor to provide a uniform heat flux over its surface. A paper thin cloth soaked with commercially available Vaseline was placed on top of the heating plate to produce thick smoke streaks that were carried downstream by a horizontal airflow. Both LED light and a laser sheet of approximately 30-degrees open angle were separately used to illuminate this flow, the latter advanced downstream with 1-cm interval from the …

Kinetics Of Molten Metal Capillary Flow In Non-Reactive And Reactive Systems, Hai Fu

Theses and Dissertations--Mechanical and Aerospace Engineering

Wetting and spreading of liquid systems on solid substrates under transient conditions, driven by surface tension and viscous forces along with the interface interactions (e.g., a substrate dissolution or diffusion and/or chemical reaction) is a complex problem, still waiting to be fully understood. In this study we have performed an extensive experimental investigation of liquid aluminum alloy spreading over aluminum substrate along with corroboration with theoretical modeling, performed in separate but coordinate study. Wetting and spreading to be considered take place during a transient formation of the free liquid surface in both sessile drop and wedge-tee mating surfaces’ configurations. The …

Comparisons Of Ablator Experimental Performance To Response Modeling And Effects Of Water Phase Transition In Porous Tps Materials, David L. Smith

Theses and Dissertations--Mechanical and Aerospace Engineering

The Mars Science Laboratory Entry Descent and Landing Instrumentation (MEDLI) project performed extensive arc jet tests for development, qualification, and calibration of instrumented heat shield plugs. These plugs each contained several thermocouples for recording near-surface and in-depth temperature response of the Phenolic Impregnated Carbon Ablator (PICA) heat shield. The arc jet test results are entered into a comprehensive database so that broad trends across the test series can be compared. One method of analysis is to compare with ablator material response calculations and solve the in-depth heat conduction equations. Using the near-surface thermocouple measurements as a boundary condition in numerical …