Mechanical Engineering Commons^™

Creating Blood Analogs To Mimic Steady-State Non-Newtonian Shear-Thinning Characteristics Under Various Thermal Conditions, Hang Yi, Alexander Wang, Christopher Wang, Jared Chong, Chungyiu Ma, Luke Bramlage, Bryan Ludwig, Zifeng Yang

Mechanical and Materials Engineering Faculty Publications

Blood analogs are widely employed in in vitro experiments such as particle image velocity (PIV) to secure hemodynamics, assisting pathophysiological diagnoses of neurovascular and cardiovascular diseases, as well as pre-surgical planning and intraoperative orientation. To obtain accurate physical parameters, which are critical for diagnosis and treatment, blood analogs should exhibit realistic non-Newtonian shear-thinning features. In this study, two types of blood analogs working under room temperature (293.15 K) were created to mimic the steady-state shear-thinning features of blood over a temperature range of 295 to 312 K and a shear range of 1~250 s−1 at a hematocrit of ~40%. Type …

Electron Beam Irradiation Effects On Bulk Metals And High Entropy Alloys (Crmnv And Crmntiv) And The Synthesis And Characterization Of Irradiation-Induced Damage In Polycrystalline Metal And High Entropy Alloy Thin Films, Najmin Ara Sultana

Mechanical & Aerospace Engineering Theses & Dissertations

Accelerator beam exit windows are designed to withstand intense radiation and mechanical stress while preserving beam transmission and structural integrity. This dissertation explores the structural and mechanical responses of pure metals and high-entropy alloys (HEAs), in both bulk and thin-film forms, under high-dose electron beam (e-beam) irradiation to identify optimal materials for next-generation accelerator exit windows. Monte Carlo simulations using FLUKA, conducted at Jefferson Lab, revealed that amongst Ni, Ti, Cr, and V, Ni exhibits the highest power dissipation, while Ti depicts the lowest power dissipation, with Cr and V demonstrating intermediate characteristics. Bulk polycrystalline (PC) and single-crystalline (SC) samples …

The Utilization Of Basic Oxygen Furnace Slag As Fine Aggregates In Concrete: Physical, Mechanical, And Durability Properties, Hakan Ozkan

Journal of Sustainable Construction Materials and Technologies

This study examines the feasibility of using basic oxygen furnace slag (BOFS) as an alternative to fine crushed limestone aggregate in concrete. BOFS is sourced from two steel production facilities in Türkiye, designated as I-BOFS and E-BOFS. The experimental results showed that as the E-BOFS aggregate replacement ratio increased, the water-to-cement (w/c) ratio increased to maintain the target workability. The concrete mixtures incorporating E-BOFS exhibited consistent reductions in the compressive strength with an increase in the BOFS ratio. At the same time, I-BOFS maintained higher compressive strength, with only minor losses up to 80% of the substitution ratio. Flexural strength …

Development Of A Self-Cured Alkali-Activated Mortar, Kübra Ekiz Barış

Journal of Sustainable Construction Materials and Technologies

Alkali-activated mortars (AAM) can be produced with self-curing (SC), which supplies internal moisture to accelerate alkaline-activation reactions. The aim of using SC is to make AAMs with an early-age strength without any additional curing energy consumption and higher CO2 emissions, and to obtain in-situ practical advantages that enable the large-scale application of AAMs. The previous study produced natural pozzolan-based AAMs by applying energy-intensive heat (HC), microwave (MWC), and hybrid (HC+MWC) curing. This study investigates alternative curing regimes that reduce production energy without compromising material properties. The impacts of air curing (AC), water curing (WC), and SC on the properties were …

Naoh Molarity Effect On Mechanical And Hydrochloric Acid Resistance Of Geopolymer Mortar Based On Slag, Mahmoud Ziada, Zahraa Mohammed Kamil Al-Mayali

Journal of Sustainable Construction Materials and Technologies

The present research investigates the influence of different sodium hydroxide (NaOH) molarities on the mechanical characteristics and hydrochloric acid (HCl) resistance of geopolymer grouts manufactured from ground granulated blast-furnace slag (GGBS). Geopolymer mortars have attracted interest as sustainable substitutes for traditional cementitious materials due to their advantageous environmental effects and enhanced durability features. This study involved the fabrication of geopolymer mortar specimens by altering the NaOH molarity (M) from 6 M to 14 M. The mechanical and physical qualities were assessed using compressive strength, capillary water absorption, flexural strength, slump flow, and ultrasonic pulse velocity (UPV) tests. Subsequently, the geopolymer …

Effect Of Expanded Perlite And Exfoliated Vermiculite Aggregate Additives On Water Vapor Permeability Performance Of Cement-Based Lightweight Mortars, Lütfullah Gündüz, Şevket Onur Kalkan

Journal of Sustainable Construction Materials and Technologies

Vapor diffusion is the movement of water vapor molecules through porous materials such as wood, insulation products, and lightweight wall elements due to differences in vapor pressure. Vapor retarders are used to control vapor diffusion through wall sections and surfaces. All building materials provide some resistance to vapor diffusion, and the amount of resistance varies depending on the material's properties. These properties can vary with relative humidity and moisture content, age, temperature, and other factors. Vapor resistance is usually expressed using the inverse term of ``vapor permeability,'' which is the relative ease of vapor diffusion through a material. Water vapor …

Rubber-Modified Self-Compacting Mortar: Evaluating Setting Time And Strength Development, Navvar Makansi, Süleyman Ipek, Erhan Güneyisi

Journal of Sustainable Construction Materials and Technologies

The influence of using crumb rubber (CR) obtained from the second scraping of used tires as fine aggregate in manufacturing self-compacting mortar (SCM) was investigated experimentally in this study. To explore this, natural fine aggregate in SCM mixes was partially replaced with CR at levels ranging from 5% to 25% by total fine aggregate volume. Two mix series, one with a total binder of 500 kg/m3 and the other with a 540 kg/m3 binder, were designed at water-to-binder ratios of 0.40 and 0.33. Ordinary Portland cement (80% by weight) and fly ash (20% by weight) were used to manufacture mortars. …

Smart Traffic Management At Intersections, Gezim Hoxha, Piotr Gorzelanczyk, Rame Likaj, Shaban Thaqi, Flori Cikaqi

Journal of Sustainable Construction Materials and Technologies

Effective traffic control methods, whether at intersections or other nodes within the road network, play a critical role in ensuring traffic quality and safety. An inappropriate choice of traffic control techniques or poorly optimized light signal programming at intersections often leads to unsatisfactory service levels. This study specifically addresses the issues related to intersections controlled by traffic lights. It aims to identify the key factors influencing the regulation and programming of traffic lights, with a focus on using different microcontrollers, particularly the Raspberry Pi. The primary objective of this research is to develop a methodology and an adapted programming approach …

Identification Of Barriers And Drivers In The Adoption Of Sustainable Construction Practices In The Turkish Construction Industry: Exploratory Factor Analysis, Tülay Çivici, Mustafa Serhan Ünlütürk

Journal of Sustainable Construction Materials and Technologies

Although the importance of sustainability in the construction industry has been emphasised by many researchers and endorsed by many authorities, it is clear that the practices in the industry still need to be improved. The primary issue for adopting sustainable practices in the construction industry is identifying the barriers and drivers. For this reason, the study analysed the literature to identify the critical barriers and incentives for adopting sustainable practices in the construction industry. In light of the information from the literature, the necessary barriers and motivators in adopting sustainable practices in the construction industry were determined, and a questionnaire …

Synergistic Effect Of Alccofine As Partial Replacement Of Cement And M-Sand As Sand Substitution In Concrete For The Assessment Of Mechanical And Microstructural Properties, Yellinedi Madhavi, R.S. Ravichandran, J. Saravanan, N. Venkatasairam Kumar

Journal of Sustainable Construction Materials and Technologies

Using supplementary cementitious materials (SCMs) and traditional binder mass has revolutionized concrete production technology in the building industry. This study examines how Alcofine-1203 affects the microstructure and mechanical characteristics of concrete. The mechanical qualities of the mixtures were evaluated using six different mixes prepared for each M25 and M40 Grade. In the proposed mixes, cement is substituted with alccofine at 0 to 25% and M-Sand as fine aggregate. The Compressive strength and ultrasonic pulse velocity were assessed after 3, 7, 14, 28, 56, and 90 days of curing, and split tensile strength and flexure strength were evaluated after 28 and …

Sustainable Modification Of Stone Column Technique With Polyethylene Terephthalate (Pet) Plastic For Strengthening The Expansive Clay, Ng Jun Shen, Muzamir Hasan

Journal of Sustainable Construction Materials and Technologies

This research investigated the modification of stone column application by the association of PET plastic as a coarse aggregate material for sustainable material replacement. Clay soil improvement with a granular material fabricated column substantially affected its soil-bearing capacity. Subsequently, it avoided severe problems such as soil settlement and structural instability. Previous studies have mentioned the function and alteration of stone columns using materials like bottom ash and fly ash. Still, no attention has been paid to the utilization of PET plastic for this area. This study examined the feasibility and reliability of materials, PET plastic, and kaolin clay S300 before …

Effect Of Reinforcement Thickness And Content On The Properties Of Compressed Earth Blocks, Salah Eddine Mokeddem, Abdelmadjid Hamouine, Rabia Abdeldjebar, Atef Hamaidi

Journal of Sustainable Construction Materials and Technologies

This study explores the mechanical, hygroscopic, and thermal behavior of stabilized and unstabilized compressed earth blocks (CEB) by incorporating date palm wood chips (DPWC) as a natural fiber additive. The investigation covers a range of DPWC thicknesses (1 mm, 2 mm, 3 mm) and content variations (0% to 1% by weight), focusing on the interaction between the bio-based reinforcement and the stabilized soil matrix, which is stabilized with 10% white Portland cement. The mixtures were compressed at a pressure of 5 MPa using a hydraulic press, providing a detailed examination of how these parameters impact the structural integrity and functional …

Energy Optimal Coverage Motion Trajectory Generation Using A Fourth-Order Motion Profile, Mathias Halinga

Tanzania Journal of Engineering and Technology (TJET)

Industrial machines are widely used in manufacturing sector to manufacture several products to meet customer demands. Most of these industries runs all the time throughout a day leading to high operating cost. To cut costs and satisfy customer demand for precise products, industrial machines’ motion generation is important in improving machine motion precision while using less energy. This study presents a coverage motion energy optimization which is generated by linear interpolation of each segment described by the fourth-order motion profile. The phase changes in the profile are attained with continuity of machine kinematic limits jerk, acceleration, and velocity, which are …

Calibration Of Measurement Tools In The Experimental Test Rig For Hydropower Performance Evaluation, Ombeni J. Mdee

Tanzania Journal of Engineering and Technology (TJET)

The demonstration of a typical hydropower plant requires the development of a test rig with the installation of tools to measure the performance parameters. The measurement tools require a calibration process to improve the quality of recorded data. This study involved the calibration of traditional and automated measurement tools connected to the hydropower test rig through an Arduino microprocessor. The automated measurement tools included a pressure transducer, flow meter, digital tachometer, and torque transducer, while traditional measurement tools, including a pressure gauge, concrete water tank, contact tachometer, and force lever arm balance, were connected in the same test rig during …

Data-Driven Constrained Control, Ali Kashani

Mechanical Engineering ETDs

Ensuring safety is a fundamental challenge. Traditional methods often rely on precise mathematical models, which are difficult, impractical, or costly to obtain for real-world systems with complex, nonlinear dynamics. This dissertation develops direct data-driven control approaches that enable safe and efficient operation of nonlinear systems without requiring explicit models or performing system identification. This effort leverages machine learning, optimization, and control theory to bridge theoretical rigor and practical applicability. Deterministic guarantees are provided based on the Lipschitz continuity of the system, and probabilistic guarantees through scenario optimization. The computation of safe sets is performed using one-shot approaches with broad neural …

Towards Metrology 4.0 In Developing Countries’ Manufacturing Industries, Jailos Nzumile

Tanzania Journal of Engineering and Technology (TJET)

A systematic literature review was conducted to unveil the status of the digital transformation of metrology in developing countries, as they are lagging in utilising fourth industrial revolution (IR4.0) technologies to transform manufacturing industries. A PRISMA technique was employed using various keywords to identify, screen, and select the relevant literature. Forty publications were selected for the review, mainly discussing IR 4.0 technologies in metrological operations. The results indicate that the digital transformation of metrology has yet to be initiated in developing countries. However, the employment of IR4.0 technologies in advancing metrological operations in manufacturing industries is mostly discussed in the …

Effects Of Cutting Conditions On Tool Temperature And Material Removal Rate In Turning Operations, Simon I. Marandu

Tanzania Journal of Engineering and Technology (TJET)

Cutting conditions in manufacturing processes have effects on tool temperature and material removal rate. The objective of this study was to investigate the effects of cutting conditions namely spindle speed, feed rate, depth of cut and tool nose radius on tool temperature and material removal rate in turning operations. A total of 81 experiments were conducted to measure tool temperature and material removal rate in order to determine the effects of cutting conditions on tool temperature and material removal rate using ANOVA and regression analysis. The results show that tool nose radius, depth of cut, and spindle speed are significant …

Potential Use Of Pump As Turbine Coupled To Self-Excited Induction Generator For Micro-Hydro Cooking And Cooling Applications, Emanuel J. Nyirenda

Tanzania Journal of Engineering and Technology (TJET)

Clean cooking and efficient cooling in developing countries have recently become areas of great focus. Further, the environmental impact of flooding in high-capacity hydroelectric plants has become a major concern. As a result, there is growing emphasis on developing sustainable and decentralized energy solutions, focusing on the potential of micro-hydro systems, especially in rural and remote areas. Although there are several alternative energy generation methods, their application is not straightforward. One of the latest technologies under research is using pumps as turbines coupled to an induction generator. This paper explores through a rigorous experimental approach the possibility of using a …

Thermal Modeling Techniques For Additively Manufactured Porous Metals, Lucas D. Rambo

Master's Theses

Advances in additive manufacturing have enabled the creation of metallic components with tailored porosity, offering design flexibility for thermal, structural, and fluid transport applications. This thesis investigates the effective thermal conductivity (ETC) of porous Inconel 625 (IN625) and Inconel-ceramic composites (IN625-RAM2) fabricated by Laser Powder Bed Fusion (LPBF) using Elementum 3D’s PermiAM technology. Experimental measurements of thermal conductivity using the laser flash method are compared to numerical models built from micro-computed tomography data. Simulations were performed using both finite element (FE) and finite volume (FV) methods to evaluate thermal transport in real microstructures. The study investigates the effects of micro- …

Mae Enewsbrief Jan-Mar 2025, Department Of Mechanical And Aerospace Engineering, Michigan Technological University

Department of Mechanical and Aerospace Engineering eNewsBrief

No abstract provided.

Mae Enewsbrief Oct-Dec 2024, Department Of Mechanical And Aerospace Engineering, Michigan Technological University

Department of Mechanical and Aerospace Engineering eNewsBrief

No abstract provided.

Comparative Study Of Experimental And Fea Strain Data For Cnt-Coated Fiberglass Sensors, Extensometers, And Metal Foil Strain Gauges, Omar Dwidar

Master's Theses

Material testing is essential across industries such as aerospace, automotive, and construction, playing a critical role in verifying material selection, diagnosing failures, and understanding the development of flaws in structures. These insights are key to designing successful, reliable systems. Conventional metal foil strain gauges are low cost and reliable but provide limited sensitivity with a typical gauge factor around 2. Extensometers provide highly sensitive strain measurements with the disadvantage of a bulky form factor. With advanced materials such as carbon nanotubes, it is possible to manufacture a sensor with the sensitivity closer to that of an extensometer with the small …

Design And Optimization Of Aquaculture Gear: Development Of A Cage-Integrated Reeling Mechanism For Oyster Farming, Felicity Bryant

Honors Theses

This project encompasses the design, fabrication, and testing of a cage-integrated reeling system aimed at reducing the physical labor required in oyster aquaculture at Bama Bay Oyster Farm, the last operational oyster farm in Mobile Bay. The proposed system includes two primary components: lightweight, modular oyster cages and a dual-winch reeling device for automated retrieval. Three cage prototypes—rectangular, oval, and hexagonal—were evaluated for structural performance and fabrication feasibility. The oval design was ultimately excluded due to practical fabrication limitations. The rectangular and hexagonal designs were fabricated using recycled materials and tested under the most extreme environmental conditions derived from years …

Tailoring Functional And Sensing Properties Of Polymer-Ceramic Composites Via 3d Printing, Alexis Lopez

Open Access Theses & Dissertations

Section 1.1. Abstract This chapter investigates the use of direct ink write (DIW) additive manufacturing to control grain orientation in non-toxic barium titanate (BTO) ceramics by blending spherical and platelet-shaped particles in the ink. A series of inks containing 0–40 wt.% BTO platelets were formulated with poly(vinyl alcohol), polyethylene glycol, poly(acrylic acid-co-maleic acid), and ammonium hydroxide to ensure printability and homogeneous dispersion. Cylindrical specimens (20 mm × 3 mm) were printed using a Hyrel 30M DIW system and subjected to de-binding (650 °C, 2 h) followed by a two-step sintering schedule (T₁: 1200–1350 °C; T₂: 700–850 °C; 24 h dwell). …

Mechanistic Insights Into Polymer-Assisted Graphene Exfoliation: The Roles Of Velocity, Adhesion, Cohesion, Temperature, Peeling Mode, And Edge Defect Via Coarse-Grained Molecular Dynamics, Linjiale Dai

All Theses

Graphene exfoliation is a critical step in the fabrication of high-quality graphene

layers. However, the underlying fracture mechanisms remain poorly understood. In this

work, I employed coarse-grained (CG) molecular dynamics (MD) simulations to

investigate how factors such as interfacial binding energy, substrate cohesion, temperature,

peeling mode, and edge defects influence the outcome of the exfoliation process. To model

polymer-assisted mechanical exfoliation, I used a finite-size system in which multilayer

graphene (MLG) is sandwiched between two thin polymer films. Leveraging the

spatiotemporal efficiency of the CG model, I performed fifty simulation iterations per

parameter set and analyzed the results from a …

Experimental And Theoretical Fracture Analysis Of Additively Manufactured Orthotropic V-Notches, Venkata Siva Sainath Bavapuram

Theses and Dissertations

This study presents a comprehensive investigation into the fracture behavior of additively manufactured orthotropic V-notched components made of Acrylonitrile Butadiene Styrene (ABS) material. The research integrates both theoretical and finite element approaches to evaluate stress intensity factors (SIFs) in Modes-I and II, which are fundamental in characterizing stress field distributions around notches under applied loading conditions. Unlike isotropic materials, where stress fields depend only on geometry of the component, the anisotropic nature of 3D-printed ABS introduces a dependency on material properties that necessitate different approaches to include anisotropy of the material.

Tensile specimens are 3D-printed with specific material orientations to …

Cellulose Recovery From Waste Denim Fabrics Through Indigo Vat Dye Reduction And Spandex Dissolution, Tito N. Venance

Tanzania Journal of Engineering and Technology (TJET)

This study addresses environmental conservation by tackling end-of-life management for post-consumer denim garments through the recycling of cotton fibres from waste denim. The purification process involved dithionite reduction of vat dyes in the presence of an alkali followed by selective dissolution of spandex using N,N-dimethylformamide (DMF). Optimal conditions for dye removal were determined at 90°C for 120 minutes with sodium hydroxide at 25 g/L, sodium dithionite at 6 g/L and PVP at 4.5 g/L, while spandex extraction was achieved using a 5% DMF solution at 70°C for 4 hours. Ultraviolet (UV)-vis spectrophotometric analysis indicated a significant increase in whiteness (DL*). …

Application Of Artificial Neural Network Models For Predicting Diesel And Petrol Prices In The Geographically Sparsed Regions In Tanzania, John M. Kafuku

Tanzania Journal of Engineering and Technology (TJET)

Fuel consumption in Tanzania, mainly diesel and petrol, accounts for 82 percent of the energy consumption in the country, with significant price volatility affecting market stability, availability of fuel, and investment decisions. This study uses an artificial neural network (ANN) with a backpropagating algorithm to predict fuel prices in four regions of Tanzania. Key input parameters include the currency inflation rate (CIR), the petrol fuel inventory (PFI), the diesel fuel inventory (DFI), and the fuel transport costs (FTC). The study selected the 6-10-10-2 ANN structures for Sumbawanga-Rukwa, Mpanda-Katavi, and Mbeya-Mbeya as well as 6-10-9-2 for the Songea-Ruvuma region. The results …

Clustering Mini-Grids To Enhance Power Systems Reliability In Distributed Generation, Santos Kihwele

Tanzania Journal of Engineering and Technology (TJET)

This study investigates the effectiveness of clustering mini-grids as a method to improve the reliability and operational stability of distributed generation systems in remote areas, particularly where renewable energy sources are predominant. As renewable resources like solar and wind are increasingly integrated into mini-grids, these systems face various challenges, particularly in maintaining stable voltage and frequency across interconnected networks. Such issues are compounded by the intermittent nature of renewable energy sources and the lack of extensive communication infrastructure in rural or resource-constrained settings. To address these control challenges, this study applies droop control techniques to two mini-grids in Uganda, utilizing …

Factors Affecting Adoption Of Industry 4.0 Predictive Maintenance By Manufacturing Industries: Tanzania Food And Beverage Manufacturing Industries, Fred E. Peter

Tanzania Journal of Engineering and Technology (TJET)

Industry 4.0 has increasingly become a focal point of scholarly inquiry. Nonetheless, there remains a noticeable lack of comprehensive research on the diverse and systematic factors that influence the adoption of Industry 4.0 Predictive Maintenance (PdM 4.0) in manufacturing sectors within developing regions, particularly in East Africa. This study seeks to bridge this research gap by investigating the key determinants affecting the actual implementation of PdM 4.0 in Tanzania’s food and beverage manufacturing industries. To achieve this objective, a mixed-methods research design was adopted, combining both qualitative and quantitative approaches. Qualitative data were obtained through in-depth interviews with ten industry …