Mechanical Engineering Commons^™

Designing, Building And Testing A Solar Thermoelectric Generation, Steg, For Energy Delivery To Remote Residential Areas In Developing Regions, Yacouba Moumouni

UNLV Theses, Dissertations, Professional Papers, and Capstones

New alternatives and inventive renewable energy techniques which encompass both generation and power management solutions are fundamental for meeting remote residential energy supply and demand today, especially if the grid is quasi-inexistent. Solar thermoelectric generators can be a cost-effective alternative to photovoltaics for a remote residential household power supply. A complete solar thermoelectric energy harvesting system is presented for energy delivery to remote residential areas in developing regions. To this end, the entire system was built, modeled, and then validated with LTspice simulator software via thermal-to-electrical analogy schemes. Valuable data in conjunction with two novel LTspice circuits were obtained, showing …

Cultural Change Through Bim: Driving Lean Transformation In Education, Avril Behan, Malachy Mathews, Kevin Furlong, Ciara Ahern, Una Beagon, Peter Brennan, Colin Conway, Lee Corcoran, Pierce Fahy, Alan Hore, Barry Mcauley, Trevor Woods

Conference papers

This paper presents a case study of how the adoption of BIM-based practices in the AECO industry is being reflected by cultural change in higher education in Ireland. The silo-mentality that has dominated the AECO sector for more than a century has, despite numerous reorganisations, been replicated in the structures of educational institutions, including in Dublin Institute of Technology since the inception of its founding colleges in the late 1800s. Most AECO programmes must include content that is external to the programme’s specific discipline. Through the School structures of the Institute, delivery of such content is known as "service teaching" …

Novel Applications Of A Thermally Tunable Bistable Buckling Silicon-On-Insulator (Soi) Microfabricated Membrane, Robert A. Lake

Theses and Dissertations

Buckled membranes are commonly used microelectromechanical systems (MEMS) structures. Recent work has demonstrated that the deflection and stiffness of these membranes can be tuned through localized joule heating. These devices were implemented into the design and fabrication of two novel device applications, a tunable pressure sensor and a steerable micromirror. A differential pressure across the membrane causes de reflection, up or down, which can be measured and related to a specific pressure. By tuning the stiffness of the membrane, its pressure response is varied providing a wider range of application for the pressure sensor. A 2.0mm by 2.0mm square membrane …

Modeling And Test Of The Efficiency Of Electronic Speed Controllers For Brushless Dc Motors, Clayton R. Green

Master's Theses

Small electric uninhabited aerial vehicles (UAV) represent a rapidly expanding market requiring optimization in both efficiency and weight; efficiency is critical during cruise or loiter where the vehicle operates at part power for up to 99% of the mission time. Of the four components (battery, motor, propeller, and electronic speed controller (ESC)) of the electric propulsion system used in small UAVs, the ESC has no accepted performance model and almost no published performance data. To collect performance data, instrumentation was developed to measure electrical power in and out of the ESC using the two wattmeter method and current sense resistors; …

Integrating Systems For Liquid/Substrate Characterization And Functional Printing, Jianyi Du, J. William Boley, Rebecca K. Kramer

The Summer Undergraduate Research Fellowship (SURF) Symposium

Gallium-Indium alloys are recently applied in fabricating soft devices, such as stretchable sensors, electric circuits, micro pumps and optics. Its printability demonstrates the possibility for a wide extension of the application. Current fabrication methods are inefficient when printing is most handled manually, and are highly dependent on material properties. There is need for a fast way to characterize material properties, and to functionally print the given shape on the substrate. This paper presents the construction of an efficiently integrated system with optical imaging and functional printing for Gallium-Indium alloys. The imaging section allows for characterization of material properties to fast …

Simulation, Control And Testing Of Advanced Hydraulic Hybrid Transmissions, Italo M. Ramos, Monika Ivantysynova, Michael Sprengel

The Summer Undergraduate Research Fellowship (SURF) Symposium

Hydraulic hybrids transmissions have the potentially to substantially improve the fuel efficiency of on road vehicles. In fact recent studies have demonstrated that this technology can improve fuel economy by upwards of 30% over competing electric hybrids. To further improve the fuel economy and performance of this technology a novel blended hydraulic hybrid transmission has been constructed at the Maha Fluid Power Research Center. While this novel hybrid architecture created by the Maha lab has many benefits over conventional systems, there are a number of control challenges present due to several discrete modes of operation. And though improving fuel economy …

Application Of Fiscal Incentives For Development Of East Natuna Gas Field For Long-Term National Natural Gas Demand, Marwan Batubara, Widodo Wahyu Purwanto, Akhmad Fauzi

Makara Journal of Technology

East Natuna gas field, which has proven reserves of 46 trillion cubic feet, is projected to meet long-term natural gas needs. However, CO2-content of the gas reserves reaches 71%, leading to expensive development costs. This research investigates the feasibility of the field based on several fiscal incentives. Firstly, gas supply-demand until year 2040 was analyzed. Then, based on the analysis, the field was developed using high CO2 gas separation technology to produce gas of 1300 MMSCFD in 2023, 2600 MMSCFD in 2031, and 3900 MMSCFD in 2039. Finally, the economic feasibility was assessed using cash flow analysis in accordance with …

Transmission Electron Microscopy Characterization Of High-Temperatur Oxidation Of Fe-20cr-5al Alloy Prepared By Focused Ion Beam Technique, Mohammad Dani, Pudji Untoro, Teguh Yulius Surya Panca Putra, Parikin Parikin, Joachim Mayer, Arbi Dimyati

Makara Journal of Technology

The Focused Ion Beam (FIB) technique was applied for cross section preparation of the oxidized alloy for Transmission Electron Microscopy (TEM) study. Prior to preparation, the specimens of Fe-20Cr-5Al alloy sheet were oxidized in air at 1200 oC for 2 minutes, 10 minutes, 2 hours, and 100 hours. The microstructure and elemental composition of the samples were characterized using TEM equipped with an Energy Dispersive X-Ray Spectroscopy (EDX). The Electron Energy Loss Spectroscopy (EELS) was used to determine of the light elements. The TEM investigation reveals remarkable microstructure evolution of the specimens during oxidation which generally exhibit a typical multi-layer …

High Temperature Corrosion Of Aluminized Aisi 4130 Steel With The Different Composition Of Nacl/Na2so4 Deposits, Mohammad Badaruddin, Chaur Jeng Wang, Yudhistyra Saputra, Abu Khalid Rivai

Makara Journal of Technology

The high temperature corrosion of AISI 4130 steel can be increased by hot-dip aluminizing coating. The aluminized steel specimens with the deposit composition of 100/0, 30/70, 50/50, 70/30, and 0/100 (wt.%) NaCl/Na2SO4 were oxidized at 750 °C for 1-49 h periods. According to a parabolic rate constant (kp) value, the aluminized steel with deposit composition of 70/30 NaCl/Na2SO4 shows the highest kp value (3.71 × 10-11 g2cm- 4s-1), later followed by the kp value of 3.35 × 10-11 g2cm-4s-1 for 100/0 and the lowest kp value is 7.731 × 10-12 g2cm-4s-1 for 0/100. Whereas, the kp value for the aluminized …

Effects Of Supplier-Manufacturer Relationships On Supply-Chain Performance Of Manufacturing Industries In Indonesia, Rachmad Hidayat, Khisbullah Hudha, Sabarudin Akhmad

Makara Journal of Technology

The present study describes the relationships between commitment, communication, satisfaction, trust, relationship quality with suppliers, and supply-chain performance. The population of the study was manufacturing companies in Indonesia. Respondents were the chief executive officers or corporate secretaries or the designated managers involved in strategic decision making. Samples were taken by using a proportional area random sampling technique. Structural Equation Modeling (SEM) was used for analysis. Results of both direct and indirect testing of hypothesis indicated two hypotheses of positive and significant effects and nine hypotheses of positive but insignificant effects. Those hypotheses of positive and significant effects were the direct …

A New Method For Simulating Power Flow Density Focused By A Silicon Lens Antenna Irradiated With Linearly Polarized Thz Wave, Catur Apriono, Eko Tjipto Rahardjo, Norihisa Hiromoto

Makara Journal of Technology

A terahertz system uses dielectric lens antennas for focusing and collimating beams of terahertz wave radiation. Linearly polarized terahertz wave radiation has been widely applied in the terahertz system. Therefore, an accurate method for analyzing the power flow density in the dielectric lens antenna irradiated with the linearly polarized terahertz wave radiation is important to design the terahertz systems. In optics, ray-tracing method has been used to calculate the power flow density by a number density of rays. In this study, we propose a method of ray-tracing combined with Fresnel’s transmission, including transmittance and polarization of the terahertz wave radiation …

Stochastic Optimization Of Supply Chain Risk Measures –A Methodology For Improving Supply Security Of Subsidized Fuel Oil In Indonesia, Adinda Yuanita, Andi Noorsaman Sommeng, Anondho Wijonarko

Makara Journal of Technology

Monte Carlo simulation-based methods for stochastic optimization of risk measures is required to solve complex problems in supply security of subsidized fuel oil in Indonesia. In order to overcome constraints in distribution of subsidized fuel in Indonesia, which has the fourth largest population in the world—more than 250,000,000 people with 66.5% of productive population, and has more than 17,000 islands with its population centered around the nation's capital only—it is necessary to have a measurable and integrated risk analysis with monitoring system for the purpose of supply security of subsidized fuel. In consideration of this complex issue, uncertainty and probability …

Thermodynamic Analysis Of Irreversible Heat-Transformers, Niccolo` Giannetti, Arnas Arnas, Andrea Rocchetti, Kiyoshi Saito

Makara Journal of Technology

Absorption heat transformers extend the possibilities for efficient and environment-friendly energy conversion processes. Based on a general thermodynamic model of three-thermal cycles with finite thermal capacity of the heat sources, this paper is intent upon analyzing and optimizing the performance of absorption heat transformers, by including the influence of irreversibility in the analytical expression of the system efficiency. Dimensionless parameters for an overall optimization are defined and a first screening is performed to clarify their influence. Dependence on the main factors is highlighted to suggest how to change them in order to enhance the whole system performance. Under this point …

Swelling-Etching Characterization Of Copper (I) Oxide - Pdms For The Development Of Micro/Nano - Particles Composite Mems Corrosion Sensor, Abdoul Kader Maiga

Graduate Theses and Dissertations

The primary objective for this thesis is to contribute to the understanding of the oxide removal process for a corrosion sensing device. The goal for designing such a device is for monitoring corrosion on metallic structures. The sensing material (6.35mm x 1mm discs) of the device is composed of copper (I) oxide particles mixed in some polydimethylsiloxane (PDMS). The PDMS, “housing,” is meant for controlling the oxidation rate through the sensing material. A solvent was used to facilitate the etchant diffusion through the PDMS matrix. Toluene and acetic acid were the ideal solvent and etchant, respectively, for carrying out the …

The Future Of Rural Communities, Alondra B. Perez, Yanliang Zhang (Mentor)

Idaho Conference on Undergraduate Research

There is a problem in how modern energy is being distributed throughout the world; less than a quarter of the population have access to energy. Limited energy access is seen in rural areas because of the costs that comes from transporting material and making modern energy resources (solar panels, wind turbines, etc..). Through research on thermoelectric devices, there have been many theories tested in order to improve energy efficiency focusing on easy maneuverable resources. At Boise State’s Advanced Energy Lab, thermoelectric generators are being created and modified which can be used to help communities from rural areas power utilities needed …

Text-Independent Speaker Identification Using Statistical Learning, Alli Ayoola Ojutiku

Graduate Theses and Dissertations

The proliferation of voice-activated devices and systems and over-the-phone bank transactions has made our daily affairs much easier in recent times. The ease that these systems offer also call for a need for them to be fail-safe against impersonators. Due to the sensitive information that might be shred on these systems, it is imperative that security be an utmost concern during the development stages. Vital systems like these should incorporate a functionality of discriminating between the actual speaker and impersonators. That functionality is the focus of this thesis.

Several methods have been proposed to be used to achieve this system …

Rsl Autonomous Rover, Cris Madrigal, Jiachi Zhang, Nicholas Peacock, Brogan O'Hara

Interdisciplinary Design Senior Theses

Autonomous vehicles are useful for a variety of applications such as military, urban, and agricultural environments. This paper discusses adding an autonomous navigation system to an all-terrain vehicle by implementing controllers that interface with its current system, installing sensors on the vehicle for obstacle detection, and developing effective safety mechanisms to prevent injury to others. The result is a vehicle capable of waypoint navigation and obstacle avoidance. Testing the vehicle showed that the LIDAR and the autonomous navigation system were integrated seamlessly, and that the sensor output signals were successfully translated into vehicle commands the existing system uses. This system …

Mobile Music: A Musical Therapy Assistance Device, Alex Hildebrand, Tanner Malkoff

Interdisciplinary Design Senior Theses

Children suffering from Cerebral Palsy often undergo gait therapy in order to strengthen and coordinate their trunks and legs. The patients often feel unmotivated to perform their gait training because the physical movements associated with it are difficult and there is no immediate reward. Physical therapists (PT) will often play music as an incentive to get the children focused on their physical therapy, but this is inefficient and impedes the PT from analyzing and tuning the patients' gait. Mobile Music is a small device designed for automating musical therapy during gait training. In this paper, we go through several design …

Might-E Wheel, Abigail Grills, Daniel Doke, Jared O'Rourke, Zach Jesberger

Interdisciplinary Design Senior Theses

Electric bikes are proving to be an increasingly reliable source of transportation, but with large price tags and existing conversion kits proving too complicated and unapproachable for the average user, commuters are failing to consider electric bicycles as an option. A prototype of a wireless, rear-wheel replacement to convert a bicycle from manual to full-power electric was built. This motorized wheel is called Might-E Wheel. Might-E Wheel was designed as the most approachable and user-friendly way to convert a bicycle from manual to full-power electric. Might-E Wheel was able to achieve a top speed of 27.5 km/h, a range of …

Uavino, Matthew Belesiu, Aaron Chung, Kirby Linvill, Nathan Carlson, Phillip Coyle, Megan Peekema

Interdisciplinary Design Senior Theses

UAVino is a drone solution that uses aerial imagery to determine the overall plant health and water content of vineyards. In general, the system focuses on automating crop inspection by taking aerial imagery of a vineyard, conducting post-processing, and outputting an easily interpreted map of the vineyard's overall health. The project's key innovation is an auto-docking system that allows the drone to automatically return to its launch point and recharge in order to extend mission duration. Long term, UAVino is envisioned as a multi-year, interdisciplinary project involving both the Santa Clara University Robotics Systems Laboratory and local wineries in order …

Intrusion Detection In Aerial Imagery For Protecting Pipeline Infrastructure, Paheding Sidike, Almabrok Essa, Vijayan K. Asari

Electrical and Computer Engineering Faculty Publications

We present an automated mechanism that can detect and issue warnings of machinery threat such as the presence of construction vehicles on pipeline right-of-way. The proposed scheme models the human visual perception concepts to extract fine details of objects by utilizing the corners and gradient histogram information in pyramid levels. Two real-world aerial image datasets are used for testing and evaluation.

Forest Sign Maker, Victor Espinosa Iii, Kevin Ly, Lisa Yip

Mechanical Engineering

Executive Summary:

The Inyo National Forest is arguably one of the most beautiful locations in California, containing natural masterpieces such as Mount Whitney and the Ancient Bristlecone Pine Forest. Despite its magnificence, the Inyo National Forest can be a treacherous region. The Friends of the Inyo take pride in being able to facilitate the viewing experience for all outdoorsmen by maintaining the mountain trails, which includes providing adequate trail signage.

Unfortunately, there is a fundamental issue with the recent state of trail signage in the Inyo National Forest: the rate at which signs are being vandalized or naturally destroyed is …

Smart Water Meter, Jeff Hufford, Eric Adler, Garrett Hall

Mechanical Engineering

No abstract provided.

Innovative Connectivity Ensuring Education (I.-C.E.E.), Luke Cole, Andrew Ma, Nicholas Ross, Daniel Williams

Electrical Engineering

This is the critical design review for the Telepresence/Telerobotic Technology for Children with Disabilities Project by team I.- C.E.E. (Innovative Connectivity Ensuring Education). This report details our telepresence system design for our client (Nathan Stilts) including design choices/justification, testing verification and procedures, and chosen components for implementation. There are seven chapters in total starting with introductory/background information followed by hardware and software design, verification, and testing and concludes with the current status of the project and what future work may need to be included.

Hydromodus: An Autonomous Underwater Vehicle, Alex Kost, Anu Mahinkanda, Jordan Read

Electrical Engineering

Hydromodus is a student-led multidisciplinary project conceived by Jordan Read designed to provide a low-cost modular hardware and software solution for researchers and scientists. For the scope of the Senior Project class, it is designed to be a baited remote underwater vehicle (BRUV), but the platform is highly modifiable and open-source.

Pier2pier: Final Report, Kevin Nelson, Anthony Miller, Paul Maalouf, Chahan Shah

Mechanical Engineering

No abstract provided.

Cal Poly Heliodon, Gregory Bucher, Lucas Carter, Jake Hamilton, Robin Hubilla

Mechanical Engineering

The purpose of the Heliodon project is to provide professors with a means to educate students about the movement of the sun and how that movement varies with location on earth and throughout the year.

Shark Alert: Early Warning System, Cory Peterson, Marc Rauschnot, Taylor Mcclain

Electrical Engineering

The Shark Alert Early Warning System is a device geared toward avid beach goers such as surfers, divers, and swimmers. The system is composed of an ultrasonic transmitter mounted on a shark’s dorsal fin and a receiver worn by the user around the ankle. The receiver alerts the user to the presence of a shark upon ultrasonic signal detection.

The receiver warns the user through both visual and tactile (vibration) alerts to ensure user notification. This circuit was built and tested in the EE labs and Recreation Center pools to determine transmission range. The receiver detects the transmitted signal up …

Veloelectric: Creating A Device That Harvests Energy From Bicycles, Austin Hall, Daniel Stohr, Tj Fox

Mechanical Engineering

Long distance mountain bikers, bike-packers, and many bikers in developing countries rely on electrical devices for safety and communication. These specific groups of people operate in areas with little to no electricity, and often times have no power to sustain their devices. The purpose of this Cal Poly senior project, VeloElectric, was to design, build, and test a kinetic energy harvester for bicycles that can be used to charge common mobile devices via USB. This senior project team created a device that attaches directly to a bicycle and uses vibrations to generate energy, which in turn powers a variety of …

Telepresence: Design, Implementation And Study Of An Hmd-Controlled Avatar With A Mechatronic Approach, Darren Michael Chan

Master's Theses

Telepresence describes technologies that allow users to remotely experience the sensation of being present at an event without being physically present. An avatar exists to represent the user whilst in a remote location and is tasked to collect stimuli from its immediate surroundings to be delivered to the user for consumption. With the advent of recent developments in Virtual Reality technology, viz., head-mounted displays (HMDs), new possibilities have been enabled in the field of Telepresence. The main focus of this thesis is to develop a solution for visual Telepresence, where an HMD is used to control the direction of a …