Mechanical Engineering Commons^™

Dynamic Characteristic Identification Of Seismic-Excited Multi-Story Buildings Through Response-Only Technique, Agung Budipriyanto, Priyo Suprobo

Makara Journal of Technology

Identifying dynamic characteristics of civil engineering structures is still a challenging task. It intends to assess behavior of the structures under time-dependent loads. This paper discusses a methodology suitable for identifying the characteristics of multi-story buildings using only their measured response under earthquake ground excitations. Appropriateness of technique used for structural identification was corroborated through coherence of the structure’s responses. The methodology was applied for identifying the characteristics of 14-story and 20-story office buildings located in a high seismic region. Responses of these two buildings recorded during three different seismic ground motions were investigated. The buildings’ response spectral densities and …

Synthesis And Characterization Of Soy-Based Polyurethane Foam With Utilization Of Ethylene Glycol In Polyol, Flora Elvistia Firdaus

Makara Journal of Technology

The use of vegetable oils on replacing petroleum has attracted attention of many researchers. The chemical structure of vegetable oils are different from petrochemicals, so the structure of soybean oil has to be chemically modified through its unsaturated fatty acid chain in triglyceride. A two step process was conducted for the preparation of soy-polyol in designated temperatures; 50 °C, 60 °C, and 70 °C. Ethylene glycol (EG) as co-reagent was taking part in soy-polyol synthesis, and the soy-polyol was used as a sole polyol for polyurethane synthesis. Referred to the previous study, the existence of EG in polyurethane synthesis can …

Performances Of Free-Space Optical Communication System Over Strong Turbulence, Ucuk Darusalam, Purnomo Sidi Priambodo, Harry Sudibyo, Eko Tjipto Rahardjo

Makara Journal of Technology

We report an experimental of free-space optical communication (FSOC) system that use tube propagation simulator (TPS) as the turbulence medium. The FSOC system use wavelength of 1550 nm at the rate transmission of 1000 Mbps and amplified with EDFA at the output of +23 dBm. Index structure of 10-15–10-13 as the representation of atmosphere index turbulences are used for simulation of intensity distribution model or scintillation. The simulation use gammagamma and K model as well. The beam wave propagation models used in simulation are plane wave, spherical wave and Gaussian wave. Spherical wave achieves highest performance via gamma-gamma in strong …

Preparations Of Nanostructured Silicide Bundles And Oxide Arrays, Hirokazu Tatsuoka, Wen Li, Erchao Meng, Daisuke Ishikwa, Kaito Nakane, Shingo Oda, Tomoji Matsushita, Natsuki Kurebayashi

Makara Journal of Technology

A variety of nanostructured silicide bundles and oxide nanowire arrays with abundant, non-toxic materials we are prepared. The CrSi2 nanowire and Mg2Si/MgO composite nanowire bundles were synthesized using a Si substrate and a SiOx nanofiber bundle, respectively. The hexagonal MoSi2 nanosheet bundles were also synthesized using a MoS2 layered material as a template. In addition, ZnO, CuO/Cu2O and a-Fe2O3 nanowire arrays were prepared on semiconductor or metallic substrates. The growth phenomena and the structural properties of the nanostructured materials awere investigated. In addition, the preparations of axial and radial nanowire structures weare examined.

Bioethanol Production From Iles-Iles And Sorghum Starch As Raw Materials (Effect Of Cacl 2 Addition And Saccharification Time), Kusmiyati Kusmiyati, Ali Mahmudi

Makara Journal of Technology

Bioethanol produced from agricultural sources is one alternative energy that has been developed to substitute for petroleum. However, the use of food sources such as corn and cassava to produce bioethanol still face obstacles that lead to the scarcity of food and an increase in food prices. The aim of this study was to produce bioethanol from sorghum and iles-iles, which are not used by humans as food, especially in Indonesia. For both materials, the variables studied were saccharification time (4, 8, 24, and 48 h) and concentration of CaCl2 added to the liquefaction slurry (0, 100, 200, 300, and …

The Effect Of Zephyr Layer Orientation On Zephyrboard Made From Oil Palm Petiole, Lusita Wardani, Muhamad Yusram Massijaya, Yusuf Sudo Hadi, I Wayan Darmawan

Makara Journal of Technology

It is very important to utilize oil palm petiole for the production of zephyr boards. This study aimed to analyze the effect of layer orientation on zephyr board quality. Zephyr boards were made with three coating patterns (A = cross perpendicular, B= combine A and C, and C= paralell) and five zephyr layers using urea formaldehyde adhesive. They were pressed for 20 min at a pressure of 25 kgf/cm² and a temperature 120 ºC, to a target density of 0.80 g/cm³ and a size of 300 mm X 300 mm X 12 mm. Our results showed that the physical and …

Performance Evaluation Of An Optimized Floating Breakwater In Oblique Waves With A Higher-Order Boundary Element Method, Faisal Mahmuddin, Masashi Kashiwagi

Makara Journal of Technology

In the previous study, the optimal performance of a two-dimensional (2D) floating breakwater shape was obtained. The performance of this shape was also confirmed with a model experiment in a towing tank. Moreover, the shape’s performance in three dimensions (3D) was investigated in a subsequent study. However, to predict the shape’s performance in a real application more accurately, the shape’s characteristics in oblique waves must also be evaluated. In this study, the performance and characteristics of the model (hydrodynamic forces, body motions, wave elevations, and drift forces) are computed using a higher-order boundary element method (HOBEM). The HOBEM, which is …

Static, Vibration Analysis And Sensitivity Analysis Of Stepped Beams Using Singularity Functions, Peng Cheng, Carla Davila, Gene Hou

Mechanical & Aerospace Engineering Faculty Publications

A systematic approach is presented in this paper to derive the analytical deflection function of a stepped beam using singularity functions. The discontinuities considered in this development are associated with the jumps in the flexural rigidity and the applied loads. This approach is applied to static and vibration analyses of stepped beams. The same approach is later extended to perform sensitivity analysis of stepped beams. This is done by directly differentiating the analytical deflection function with respect to any beam-related design variable. The particular design variable considered here is the location of discontinuity in flexural rigidity. Example problems are presented …

Integrated Sustainability Decision-Making Framework, Michael Paul Cole

Open Access Theses & Dissertations

The Integrated Sustainability Decision-Making Framework (ISDMF) is an 'ideal case' framework developed at the University of Texas El Paso (UTEP) from 2012 to present to provide the most comprehensive and concise sustainability strategy and decision-making template available.

Sustainable decision-making improves community Quality of Life, but is often beyond the reach of the majority. A framework that is most approachable, actionable, and adoptable can accelerate convergence on and continued operation of a sustainable solution. Research confirms that published frameworks continuously emerge, and are infinite in number. Iterations benefit from prior work, and contribution occurs when an 'ideal case' is envisioned, best …

Numerical Simulations Of Dynamic Behavior Of Polyurea Toughened Steel Plates Under Impact Loading, Chien-Chung Chen, Daniel G. Linzell

Department of Civil and Environmental Engineering: Faculty Publications

The objective of the work discussed herein is to develop a nonlinear 3D finite element model to simulate dynamic behavior of polyurea toughened steel plates under impact loading. Experimental and numerical work related to model development are presented. Material properties are incorporated into numerical models to account for strain-rate effects on the dynamic behavior of polyurea and steel. One bare steel plate and four polyurea toughened steel plates were tested under impact loading using a pendulum impact device. Displacement time-history data from experimental work was used to validate the numerical models. Details on material model construction, finite element model development, …

Model Updating And Structural Health Monitoring Of Horizontal Axis Wind Turbines Via Advanced Spinning Finite Elements And Stochastic Subspace Identification Methods, Antonio Velazquez Hernandez

Dissertations, Master's Theses and Master's Reports - Open

Wind energy has been one of the most growing sectors of the nation’s renewable energy portfolio for the past decade, and the same tendency is being projected for the upcoming years given the aggressive governmental policies for the reduction of fossil fuel dependency. Great technological expectation and outstanding commercial penetration has shown the so called Horizontal Axis Wind Turbines (HAWT) technologies. Given its great acceptance, size evolution of wind turbines over time has increased exponentially. However, safety and economical concerns have emerged as a result of the newly design tendencies for massive scale wind turbine structures presenting high slenderness ratios …

College Of Engineering Senior Design Competition Fall 2013, University Of Nevada, Las Vegas

Fred and Harriet Cox Senior Design Competition Projects

Part of every UNLV engineering student’s academic experience, the senior design project stimulates engineering innovation and entrepreneurship. Each student in their senior year chooses, plans, designs, and prototypes a product in this required element of the curriculum. A capstone to the student’s educational career, the senior design project encourages the student to use everything learned in the engineering program to create a practical, real world solution to an engineering challenge. The senior design competition helps focus the senior students in increasing the quality and potential for commercial application for their design projects. Judges from local industry evaluate the projects on …

Microgrid Development Using A Grid Tie Inverter, Hartono Budi Santoso, Budiyanto Budiyanto

Makara Journal of Technology

The use of renewable energy sources (RES), especially photovoltaic (PV), to meet the demand of electrical energy has been getting a great deal of attention as an alternative solution to electrical energy deficit problems. RES are being applied in power systems in a variety of configurations including microgrid systems. One of the characteristics of a microgrid is capability to supplying power to grid when there is an excess power to supply local load. This research examines the chances of saving power consumption from grid using power converters grid tie inverter (GTI) in a microgrid configuration. The test is done by …

Surface Treatment Of Fly Ash For Improving The Tensile Strength Of Fly Ash/Unsaturated Polyester Composites, Sugiman Sugiman, Paryanto Dwi Setyawan

Makara Journal of Technology

The paper presents the surface treatment of fly ashes using acid and alkali solution on the tensile strength of the fly ash/unsaturated polyester (UP) composites. Sulfuric acid (H2SO4), hydrofluoric acid (HF) and sodium hydroxide (NaOH) solution with concentration of 0%, 5%, 10%, 15%, and 20% (by weight) were used for surface treatment of fly ashes. Generally, the tensile strength of the treated fly-ash/UP composites shows a significant increase compared to the untreated fly ash. Of all surface treatments studied, the optimum tensile strength was obtained at a concentration of 10%. At this concentration, at a fly ash content of 30% …

Recycling Roof Tile Waste Material For Wall Cover Tiles, Ambar Mulyono, Silfia Mona Aryani, Joko Lulut

Makara Journal of Technology

Prior research on roof tile waste treatment has attempted to find the appropriate technology to reuse old roof tile waste by create wall cladding materials from it. Through exploration and experimentation, a treatment method has been discovered to transform the tile fragments into artificial stone that resembles the shape of coral. This baked clay artificial stone material is then processed as a decorative element for vertical surfaces that are not load-bearing, such as on the interior and exterior walls of a building. Before applying the fragments as wall tiles, several steps must be taken: 1) Blunting, which changes the look …

Synthesis Of Tungsten Oxide Nanowires Onto Ito Glass Using T-Cvd, Tomy Abuzairi, Bohr-Ran Huang, Tzu-Ching Lin

Makara Journal of Technology

Tungsten oxide is an n-type semiconductor with interesting physical and chemical properties that make it suitable for various technological applications. Tungsten oxide nanowires were synthesized not only at low temperature but also without the use of any catalysts. The tungsten oxide nanowires were synthesized at 550 °C with tungsten layers onto the ITO glass using thermal chemical vapor deposition (T-CVD). The SEM image shows that the tungsten oxide nanowires are effectively grown with the 200 nm tungsten film. The Raman spectra shoulder at ~690 cm-1 proves the synthesized of tungsten oxide nanowires.

Semiconductor Thermal Neutron Detector, Toru Aoki, Aki Miyake, Takayuki Nakano, Akifumi Koike, Hisashi Morii, Hidenori Mimura

Makara Journal of Technology

The CdTe and GaN detector with a Gd converter have been developed and investigated as a neutron detector for neutron imaging. The fabricated Gd/CdTe detector with the 25 mm thick Gd was designed on the basis of simulation results of thermal neutron detection efficiency and spatial resolution. The Gd/CdTe detector shows the detection of neutron capture gamma ray emission in the 155Gd(n, g)156Gd, 157Gd(n, g)158Gd and 113Cd(n, g)114Cd reactions and characteristic X-ray emissions due to conversion-electrons generated inside the Gd film. The observed efficient thermal neutron detection with the Gd/CdTe detector shows its promise in neutron radiography application. Moreover, a …

Radiation Characteristics Of A Planar Strip Dipole Antenna And A Slot Dipole Antenna For Thz Applications, Catur Apriono, Eko Tjipto Rahardjo

Makara Journal of Technology

The development of a THz system often requires a device that is used to radiate or detect THz waves. One way to fulfill this requirement is to use an antenna. Therefore, we need to consider the radiation characteristics of an antenna working in the THz region. In this paper, we present simulation study of two dipole antennas, i.e. a planar strip dipole antenna and a slot dipole antenna. The simulation results show that a planar strip dipole antenna has a better radiation efficiency (more than 95%) compared to the slot dipole. It also shows that an efficiency of more than …

The Effect Of Pressing Temperature And Time On The Quality Of Particle Board Made From Jatropha Fruit Hulls Treated In Acidic Condition, Apri Heri Iswanto, Fauzi Febrianto, Yusuf Sudo Hadi, Surdiding Ruhendi, Dede Hermawan

Makara Journal of Technology

The high of pH of jatropha fruit hulls causes the negative properties of particleboard made from this material. Adjusting the particle acidity and pressing conditions (temperature and time) is among the technical modifications available to improve this particleboard’s properties. Particle acidity has been adjusted in a previous research project, and immersing the particles in acetic acid was found to be the best treatment in this preliminary research. In order to improve the particleboard’s properties, an experiment was conducted to determine the best pressing temperature and time. The objective of the research was to evaluate the influence of pressing temperature and …

Ole Miss Engineer 2013-2014

Ole Miss Engineer

No abstract provided.

Sodhana Environmental - Final Design Report, Eric Taylor, Corissa Bellis, Cody Perez, Cameron Zeller

Mechanical Engineering

A fully designed cost-effective, sustainable, toilet for the developing world.

Mode I Fracture Toughness Of Eight-Harness-Satin Carbon Cloth Weaves For Co-Cured And Post-Bonded Laminates, Josh E. Smith

Master's Theses

Mode I interlaminar fracture of 3k 8-Harness-Satin Carbon cloth, with identical fill and weft yarns, pre-impregnated with Newport 307 resin was investigated through the DCB test (ASTM D5528). Crack propagations along both the fill and weft yarns were considered for both post-bonded (co-bonded) and co-cured laminates. A patent-pending delamination insertion method was compared to the standard Teflon film option to assess its applicability to mode I fracture testing. The Modified Beam Theory, Compliance Calibration method, and Modified Compliance Calibration method were used for comparative purposes for these investigations and to evaluate the validity of the proposed Equivalent Stiffness (EQS) method. …

Load Path Uncertainty In A Wood Structure And The Effect On Structural Reliability, Wenqi Wang, Christopher D. Eamon

Civil and Environmental Engineering Faculty Research Publications

The roof truss bearing points of a light-framed wood house were instrumented with load cells. It was found that under dead load alone, symmetric and theoretically identical truss reactions have significant variation. A similar degree of reaction discrepancy was found under the application of uplift pressures caused by hurricane winds. Analysis revealed that the majority of this discrepancy is caused by inherent uncertainties in load path. Although uncertainties in load magnitude and material resistance are accounted for in design by use of appropriate load and resistance factors, load path is generally taken to be deterministic. In this study, load path …

Reliability Analysis Of Reinforced Concrete Columns Exposed To Fire, Christopher D. Eamon, Elin A. Jensen

Civil and Environmental Engineering Faculty Research Publications

A reliability analysis is conducted on reinforced concrete columns subjected to fire load. From an evaluation of load frequency of occurrence, load random variables are taken to be dead load, sustained live load, and fire temperature. Resistance is developed for axial capacity, with random variables taken as steel yield strength, concrete compressive strength, placement of reinforcement, and section width and height. A rational interaction model based on the Rankine approach is used to estimate column capacity as a function of fire exposure time. Various factors were considered in the analysis such as fire type, load ratio, reinforcement ratio, cover, concrete …

Semi-Active Structural Control Of A 2-Story Shear Building, Alana K. Wilbee, Shirley Dyke

The Summer Undergraduate Research Fellowship (SURF) Symposium

With continuing urban development across the world, it is becoming ever more important to provide increased structural safety against events such as earthquakes and strong winds. The field of structural control has recently been growing to meet these challenges through the use of semi-active control methods, such as the Magnetorheological (MR) Damper. However, due to the non-linearity of the device, the knowledge base surrounding the MR Damper and its various control algorithms still needs to be strengthened before large-scale implementation of this control method can occur. To address these issues, this study will examine a two story benchmark structure using …

Dimensionless Criteria For Selecting Tidally-Influenced Advective-Dispersive Desalination Brine Mixing Plume Characterization Models, Alireza Shahvari

Civil & Environmental Engineering Theses & Dissertations

The very nature of requirements for implementing a desalination process is highly spatial due to the need to secure both a source for the operation and sink for brine dilution. Thus, the applicable coastal location is bound to natural tidal mixing characteristics and subjected to a near- or a far-field availability for source and sink. Mixing characteristics of coastal waters are very different from one point to another due to the spatiotemporal tidal characteristic in loco in a manner that it can vary from being highly advective to completely dispersive dominant. Once a location is identified, estimation of corresponding water …

The Effect Zeolite Addition In Natural Rubber Polypropylene Composite On Mechanical, Structure, And Thermal Characteristics, Nurdin Bukit, Erna Frida

Makara Journal of Technology

This study was conducted to determine the effect of zeolite as filler on mechanical properties, and thermal structure blends of natural rubber and polypropylene (NR/PP). In this study, NR/PP/PP-g-MA blends was filled uncalcined zeolite and calcined zeolite at different weight percent of the 2, 4, and 6%. Samples were characterized to determine the tensile strength, fracture elongation and Young's modulus. Structure of the samples was investigated using XRD method and thermal characteristics were analyzed using DTA/TGA technique. The results obtained for tensile strength showed a significant influence with the addition zeolite of the NR/PP blends at 2% by weight of …

Characteristics Of Vacuum Freeze Drying With Utilization Of Internal Cooling And Condenser Waste Heat For Sublimation, Muhammad Idrus Alhamid, Nasruddin Yusuf, Indra Teuku Meurah Mahlia, Engkos Ahmad Kosasih, Muhamad Yulianto, Rio Ricardi

Makara Journal of Technology

Vacuum freeze drying is an excellent drying method, but it is very energy-intensive because a relatively long drying time is required. This research investigates the utilization of condenser waste heat for sublimation as a way of accelerating the drying rate. In addition, it also investigates the effect of internal cooling combined with vacuum cooling in the pressure reduction process. Jelly fish tentacles were used as the specimen, with different configurations for condenser heat waste and internal cooling valve opening. The results show that heating with condenser heat waste can accelerate the drying rate up to 0.0035 kg/m2.s. In addition, pre-freezing …

A New Experimental Approach To Evaluate Plasma-Induced Damage In Microcantilever, Yuki Nishimori, Shinji Ueki, Masakazu Sugiyama, Seiji Samukawa, Gen Hashiguchi

Makara Journal of Technology

Plasma etching, during micro-fabrication processing is indispensable for fabricating MEMS structures. During the plasma processes, two major matters, charged ions and vacuum–ultraviolet (VUV) irradiation damage, take charge of reliability degradation. The charged ions induce unwanted sidewall etching, generally called as “notching”, which causes degradation in brittle strength. Furthermore, the VUV irradiation gives rise to crystal defects on the etching surface. To overcome the problem, neutral beam etching (NBE), which use neutral particles without the VUV irradiation, has been developed. In order to evaluate the effect of the NBE quantitatively, we measured the resonance property of a micro-cantilever before and after …

Fatigue Life Prediction Of The Keel Structure Of A Tsunami Buoy Using Spectral Fatigue Analysis Method, Angga Yustiawan, Ketut Suastika, Wibowo Harso Nugroho

Makara Journal of Technology

One of the components of the Indonesia Tsunami Early Warning System (InaTEWS) is a surface buoy. The surface buoy is exposed to dynamic and random loadings while operating at sea, particularly due to waves. Because of the cyclic nature of the wave load, this may result in a fatigue damage of the keel structure, which connects the mooring line with the buoy hull. The operating location of the buoy is off the Java South Coast at the coordinate (10.3998 S, 108.3417 E). To determine the stress transfer function, model tests were performed, measuring the buoy motions and the stress at …