Mechanical Engineering Commons^™

Analysis Of Kancil's Car Knuckle Prototype, Tresna P. Soemardi, Aida Mahmudah

Makara Journal of Technology

Analysis of Kancil’s Knuckle Prototype. The objective of this work is to execute strength analysis of knuckle, which is made from FCD 50, by using static analysis on maximum loading. This maximum loading is obtained from front axle loading calculation on particular operating condition. That is, vehicle is braking while cornering in down hill. From previous vehicle loading calculation, we get a number of loading values on different speed and deceleration. At the end, we get a value of speed and deceleration that guarantee the vehicle safety if it is braking while cornering in down hill. As comparison, loading calculation …

Pid Fuzzy Logic Controller System For Dc Motor Speed Control, H. Samsul Bachri M.

Makara Journal of Technology

PID Fuzzy Logic Controller System for DC Motor Speed Control. A good controller system must have resilience to disturbance and must be able to response quickly and accurately. Problem usually appears when PID controller system was built sensitively hence the system’s respon to the disturbance will yield big overshot/undershot then the possibility of oscillation to be happened is excelsior. When the controller system was built insensitively, the overshot/undershot will be small but the recovery time will be longer. Hybrid controller system could overcome those problems by combining PID control system with fuzzy logic. The main control of this system is …

Quarternair Cugasete And Cuga0.5in 0.5te2 Thin Films Fabrication Using Flash Evaporation, A. Harsono Soepardjo

Makara Journal of Technology

Quarternair CuGaSeTe and CuGa0.5In 0.5Te2 Thin Films Fabrication Using Flash Evaporation. Quarternair materials CuGaSeTe and CuGa0.5In 0.5Te2 are the basic materials to solar cell fabrication. These materials have high absorption coefficients around 103 – 105 cm-1 and band gap energy in the range of 1-5 eV. In this research, the films were made by flash evaporation method using quarternair powder materials of CuGaSeTe and CuGa0.5In 0.5Te2 to adhere in a glass substrate. After the films were obtained, the properties of these films will be characterized optically and electrically. The lattice parameter of the films and the crystalline film structure were …

Graded Channel Mosfet Simulation With S-Pisces 2b, Hartono Siswono

Makara Journal of Technology

Graded Channel MOSFET simulation with S-Pisces 2B. Graded-Channel Metal-Oxide-Semiconductor Field-effect- Transistor or GCMOSFET is being discussed in this paper. GCMOSFET technology has been developed to meet the growing demand for low power and high performance application. In this paper, it will be shown that, compared to ungraded MOSFET, the GCMOSFET device offers the advantage of significantly higher drive current. The higher drive current is achieved because the effecctive channel length of GCMOSFET is shorter than the ungraded MOSFET’s. From the simulation result with S-PISCES 2B and MATLAB, it can been shown that the ID from GCMOSFET is higher than the …

Construction Of Depth-Structure Shelf-Edge Map For Case Study Of Kujung Formation, East Java Sea, Saifatur Rusli, Suparto Suparto

Makara Journal of Technology

Construction of Depth-Structure Shelf-edge Map for Case Study of Kujung Formation, East Java Sea. In general, reflection seismic method has capability to represent sub-surface in time domain. Seismic cross-section that depicts the formation of sub-surface usually use time domain in the format of TWT (Two Way Times). This due to in the process of seismic data acquisition, seismic wave propagates in down-going and up-going manner so that the obtained results from data processing are in the format of TWT seismic vs. shot points. This paper will describe the construction of depth-structure map for case study of Kujung Formation, East Java …

The Contextable: Building And Testing An Intelligent, Context-Aware Kitchen Table, Daniel Matthew Hoopes

Theses and Dissertations

The purpose of this thesis was to design and evaluate The ContexTable, a context-aware system built into a kitchen table. After establishing the current status of the field of context-aware systems and the hurdles and problems being faced, a functioning prototype system was designed and built. The prototype makes it possible to explore established, untested theory and novel solutions to problems faced in the field.

Ole Miss Engineer 2004

Ole Miss Engineer

No abstract provided.

Understanding Manufacturing Energy Use Through Statistical Analysis, J. Kelly Kissock, John Seryak

Mechanical and Aerospace Engineering Faculty Publications

Energy in manufacturing facilities is used for direct production of goods, space conditioning, and general facility support such as lighting. This paper presents a methodology for statistically analyzing plant energy use in terms of these major end uses. The methodology uses as few as 60 data points that are relatively easy for most plants to obtain. Multivariable change-point models of electricity and natural gas use as functions of outdoor air temperature and production data are then developed. The statistical models can be used to predict energy use for energy budgeting, measure savings, determine cost structures, and diagnostic purposes. Moreover, in …

Estimating Energy Savings In Compressed Air Systems, Chris Schmidt, J. Kelly Kissock

Mechanical and Aerospace Engineering Faculty Publications

Compressed air is typically one of the most expensive utilities in an industrial facility. As a result, potential savings opportunities are aggressively sought out and identified. Once identified, projected energy savings must be calculated in order to justify the cost of implementing the savings opportunity. It is important to calculate projected energy and cost savings as accurately as possible. Unfortunately, savings are frequently overestimated because the methods used to estimate savings neglect to consider important factors such as compressor control and type, storage, and multiple compressor operation.

In this paper, a methodology is presented for modeling air compressor performance and …

Adoption Of Variable Rate Technology, Isti Surjandari, Marvin T. Batte

Makara Journal of Technology

Site Specific Management (SSM), which also variously referred to as Variable Rate Technology (VRT), is an emerging technology that enables producers to make more precise input application decisions based on soil and field characteristics. This study analyzes factors influencing the adoption of VRT for fertilizer application for cash grain production in Ohio. Results show that producer and field characteristics might influence the adoption decision on various SSM components differently. It also provides insight as to the sequence of adoption of SSM component technologies and how this sequence might differ for producers of differing characteristics.

Study On Electrochromic Effect Of Polyaniline Film, Lienda Handojo, Junus Simangunsong

Makara Journal of Technology

Study on Electrochromic Effect of Polyaniline Film. The light transmission factor of an electrochromic film changes reversibly with the application of an electrical voltage. Thereby the transparent film becomes reversibly opaque so that it may be used to control light transmission. In this paper the results of a study on polyaniline film as an electrochromic active material is reported. Polyaniline looks yellow transparent in the reduced state and turns to green-blue at its oxidized state. The electrochromic device considered in this paper was fabricated in planar configuration of ITO glass − polyaniline film − electrolyte − ITO glass which involved …

Role Of K3-Xhxpw12o40 As A Catalyst In Selective Catalysis Of Methylamine Synthesis From Ammonia And Methanol, Mohammad Nasikin

Makara Journal of Technology

Role of K3-xHxPW12O40 as a Catalyst in Selective Catalysis of Methylamine Synthesis from Ammonia and Methanol. Synthesize of methylamine from methanol and ammonia was studied in this research work using a partially potassium heteropoly salt (K3-xHxPW12O40 abbreviated as KPW) as a catalyst. KPW was prepared from heteropoly salt and potassium carbonate by using ion exchange method. The reaction was conducted at 600 ~ 800K and at the atmospheric pressure. Reactor used was a continue flow reactor with W/F=0,1~0,9g-kat.mnt./cc.Concentration of reactants and products were analyzed by gas chromathography while catalyst structure was observed by XRD (X-ray diffraction). Isothermal adsorption method was …

Identification Of The First Limiting Amino Acid In Cooked Polished White Rice Fed To Weanling Holtzman Rats, Mellova Masrizal, J. B. Lamb

Makara Journal of Technology

Forty-eight male weanling rats (91 g) were utilized to study the nutritional adequacy of cooked polished white rice. Rats were individually housed, and allowed ad libitum access to one of six treatment diets. Treatment diets were 1) polished white rice plus 10% casein and 0.18% methionine, CAS, 2) polished white rice, WHR, 3) polished white rice plus 0.45% lysine, LYS, 4) polished white rice plus0.40% methionine, MET, 5) polished white rice plus 0.30% threonine, THR, 6) polished white rice plus 0.45% lysine, 0.40% methionine, and 0.40% threonine, COM. Rice was cooked prior diet formulation using a 3 to 1 ratio …

Application Of Tabu Search Algorithm In Job Shop Scheduling, Betrianis Betrianis, Putu Teguh Aryawan

Makara Journal of Technology

Application of Tabu Search Algorithm in Job Shop Scheduling. Tabu Search is one of local search methods which is used to solve the combinatorial optimization problem. This method aimed is to make the searching process of the best solution in a complex combinatorial optimization problem(np hard), ex : job shop scheduling problem, became more effective, in a less computational time but with no guarantee to optimum solution.In this paper, tabu search is used to solve the job shop scheduling problem consists of 3 (three) cases, which is ordering package of September, October and November with objective of minimizing makespan (Cmax). …

Alum And Pacl Coagulation, Winarni Winarni

Makara Journal of Technology

Alum and PACl Coagulation. Coagulation occurs by interaction of aluminum hydrolysis products with the contaminant such as colloidal particles. It is necessary to consider the different aluminum species that may present during specific conditions, since the mechanism of turbidity removal is dependent upon them. PACl consists of preformed aluminum hydrolysis products, which are stable below pH 6 and less sensitive than in situ hydrolysis product, alum. The benefits of PACl relative to alum have been investigated as a function of pH and Al dosages. Specific conditions and aluminum species that exist during the certain mechanisms of coagulation are discussed. Results …

The Selection Of Materials For Roller Chains From The Perspective Of Manufacturing Process, Rahmat Saptono

Makara Journal of Technology

The selection of materials for an engineering component is not only requested by its design function and shape, but also the sequence through which it is manufactured. The manufacturing operation of roller chains involves drawing and trimming processes aimed at producing semi-finished chain drives component with a well-standardized dimension. In addition to final combination of properties required by design constraints, the ability of materials to be formed into a desired shape and geometry without failure is also critical. The objective of materials selection should therefore involve additional attributes that are not typically accommodated by the standard procedure of materials selection. …

An Economic Analysis Of Variable Rate Technology, Isti Surjandari, Marvin T. Batte, Mario J. Miranda

Makara Journal of Technology

Variable Rate Technology (VRT) offers an opportunity to improve production efficiency by allowing input applications to fluctuate in response to spatial variations in soil characteristics and nutrient levels. Society may also benefit from reduced negative externalities, such as surface and groundwater contamination, from input applications. Using a dynamic spatial model, this study examines how the interaction among variability, spatial autocorrelation, and mean level of soil fertility affects optimal sampling density and the economic gains from VRT. VRT was found to be profitable under selected conditions, and the optimal grid size will vary with these conditions. In the case where variability …

Ole Miss Engineer 2003

Ole Miss Engineer

No abstract provided.

A Descriptive Performance Model Of Small, Low Cost, Diskless Beowulf Clusters, Curtis R. Nielson

Theses and Dissertations

Commodity supercomputing clusters known as Beowulf clusters, have become a low cost alternative to traditional supercomputers. Beowulf clusters combine inexpensive computers and specialized software to achieve supercomputing power. The processing nodes in a diskless Beowulf cluster do not have a local hard disk unlike the nodes in most commodity clusters. Research has provided performance information for diskless clusters built with expensive, high performance equipment. Beowulf clusters use commodity off-the-shell hardware, and little information is available about their performance. This research includes the construction of several diskless Beowulf clusters. Using the NAS Parallel Benchmarks, the performance of these clusters was measured. …

Mapping Of Ecosystems In Mount Bromo Using Remote Sensing Technology, Bangun Muljo Sukojo

Makara Journal of Technology

Mapping of Ecosystems in Mount Bromo Using Remote Sensing Technology. Covered land analyses of Landsat image have been done to get ecosystem types and map in Mount Bromo region using remote sensing technology. There are nine types of ecosystems in Mount Bromo region, i.e. primary forest, secondary forest, lake, crater, sands, uncovered land, underbrush, dry-field and residence. Distribution of rock analysis has also been done by comparing the manual image interpretation with geological map. The results were coorelated with the digital image interpretation to find rock distribution map which can be useful to get the information about water reservation potencial …

Capacity Of High-Speed Powerline Communication In Vehicles, Deny Hamdani, Ery Safrianti

Makara Journal of Technology

Powerline Communication (PLC) Systems intents to use the mains network in vehicles for high-speed data transmission. Carrier frequencies in the range of MHz are required to establish data rates of some megabits per second. In this paper, typical reference channels extracted from channel measurements are presented and computation results of their capacities according to Shannon’s theorem are presented. Furthermore, the effect of limitations of frequency range and power spectral density of transmitted signal on achievable capacity is investigated. This paper outlines an assessment for theoretical channel capacity and achievable data rates of vehicular PLC transmission schemes. Finally, EMC (Electromagnetics Compatibility) …

Diffuser Optimation At Exhaust System With Catalytic Converter For 110 Cc Mopet With Fluid Flow Cfd Simulation, Tresna P. Soemardi, Ahmad Indra Siswantara, Erwin Erwin

Makara Journal of Technology

Diffuser Optimation at Exhaust System with Catalytic Converter for 110 cc Mopet with Fluid Flow CFD Simulation. CFD simulation used to get behavior of exhaust gas through catalyst, this result will be used to optimize geometry form to perform uniform stream distribution to catalyst, and CFD Simulation will used to analyze backpressure that happened at the model.

The Study On Fluorescence Characteristics Of Chlorella Spp: Ph Influence On Culture, Retno Wigajatri P., Andrianto Handojo, Hendrik Kurniawan, N. B. Prihantini

Makara Journal of Technology

The Study on Fluorescence Characteristics of Chlorella spp: pH Influence on Culture. Experiments for measuring the fluorescence characteristics of Chlorella spp. by using high stability and high repetition rate nitrogen laser of energy 5 mJ with pulse duration of 5 ns have been carried out. The results show that for a cell concentration range from 2,625 cells/ml up to 2,769,000 cells/ml, the fluorescence intensities at pada λ = 687 nm have a linear relationship with the cell concentration. It has been also found that for a 7 days old chlorella culture, the pH variation at the starting culture influenced the …

The Performance Analysis Of A Unicast Network When Two Protocols, Sctp (Stream Control Transmission Protocol) And Tcp (Transmission Control Protocol) Coexist In The Network, Bagio Budiardjo, Michael Thiotrisno

Makara Journal of Technology

This paper elaborates the performance analysis of a unicast network when two protocols, SCTP (Stream Control Transmission Protocol) and TCP (Transmission Control Protocol) coexist in the network. These two protocols are tested using File Transfer Protocol (FTP) and Constant Bit Rate (CBR) based traffic. From the simulations, it could be concluded that SCTP could achieve better throughput compared to TCP in both FTP and CBR based traffic, with sufficiently high fairness index of both intrafairness and interfairness. The increase of simulation time yields to the increase and relatively stable network performance. The increase of the number of sessions of small …

Signal Mast Arm Fatigue Failure Investigation, Genda Chen, Michael G. Barker, Lokeswarappa R. Dharani, Christopher W. Ramsay

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The Missouri Department of Transportation (MoDOT) has discovered and documented failures in several cantilever mast arms in the recent years. The failures were primarily by fatigue at the weld of the arm to the base plate attached to the mast. With over 6000 mast arms in service in Missouri, the failures raised concerns with the existing mast arm inventory and future mast arm design. This report presents findings from an effort to determine the cause of unexpected cracking in Missouri mast arms. Three causes of premature failure were investigated: the stress ranges experienced at the weld detail were higher than …

Study About High Influence Doping To Base Resistance And Bandgap Narrowing At Si/Si1-Xgex/Si Heterojunction Bipolar Transistor, Achmad Fadhol

Makara Journal of Technology

Study About High Influence Doping to Base Resistance and Bandgap Narrowing at Si/Si1-xGex/Si Heterojunction Bipolar Transistor. Heterojunction is a link formed bedween two semiconductor materials and differend bandgap which has thinness under 50nm and grow the mixture of plate SiGe as bases. The link is an abrupt link or graded one. In this research learnt formulation of doping concentration influence to basis resistance and bandgap narrowing through Si/Si1-xGex/Si Heterojunction Bipolar Transistor with abrupt emitter-basis link, besides taking care to mobility and basis wide to basis resistance, it is also influence of mole fraction to bandgap power. From the result shows …

Photocatalytic Treatment Of Heavy Metal Waste Cr(Vi) Withtio2 Photocatalyst, Slamet Slamet, Riyadi Syakur, Wahyu Danumulyo

Makara Journal of Technology

Photocatalytic Treatment of Heavy Metal Waste Cr(VI) with TiO2 Photocatalyst. The photocatalytic reduction of hexavalent chromium/Cr(VI) using TiO2 and copper-doped TiO2 as photocatalysts have been studied in stirred tank and circulating photoreactors. All photocatalysts were characterized with FTIR (Fourier Transform Infra Red), BET (Brunauer-Emmett-Teller), XRD (X-Ray Diffraction) and SEM (Scanning Electron Microscope). TiO2 Merck and Degussa P-25 are the commercial photocatalysts used to compare the photocatalytic activity of all the prepared catalysts. Blank test experiments as well as the effect of dopants, EDTA (ethylenediaminetetraacetic acid) and activated carbon addition were studied. Cr(VI) reduction on various pH and initial Cr(VI) concentration …

Development And Analysis Of Geographic Information System For Electricity Network (Case Study: Surabaya Industrial Estate Rungkut In Surabaya)., Lilik Jamilatul Awalin, Bangun Muljo Sukojo

Makara Journal of Technology

Development and Analysis of Geographic Information System for Electricity Network (Case Study: Surabaya Industrial Estate Rungkut in Surabaya). Geographic Information System (GIS) is a system of data which has spatial base. This may be cause has ability to process and analysis data quickly. The ability of GIS will be able to process the alternative in decision making. The need of electric power grows until recent time along with the existence of industrial sector expansion and land use expansion claim better service, large and balance stock of electric power. GIS is a solution for planning and managing data base system, for …

Application Of Remote Sensing And Geographic Information System Methods For Land Using Difference, Bangun Muljo Sukojo, Diah Susilowati

Makara Journal of Technology

Application of Remote Sensing and Geographic Information System Methods for Land Using Difference. Land using difference analysis has been done using remote sensing and Geographic Information System (GIS) methods. Identification of land using difference was conducted using map overlaying process of 1990s (digitized scalling 1:50.000) and 1997s land using map (interpreted from Landsat TM (Thematic Mapper) Image 1997) with UTM (Universal Transverse Mercator) coordinate. Image enhancement was done through histogram equalization with supervised classification devided into 7 classes: rice field, settlement, dry field, industry, pond, sport field and bush. Land using difference and river pollution BOD (Biological Oxygen Demand), COD …

Phase Composition Analysis Using Rietveld Methode And It's Influence To The Hardness Of Ti-Si-N Nanocomposites, Keba Moto, Lia Setiarini, Zufar Abubakar

Makara Journal of Technology

Phase composition analysis using rietveld methode and it’s influence to the hardness of Ti-Si-N nanocomposites. XRD data of nanocomposites Ti-Si-N have been analysed using GSAS based on Rietveld Method in order to identify phases and their composition as well as its influence on the hardness of these nanocomposites. Several new phases have been found in the sample beside the nc-TiN/a-Si3N4& a-/nc-TiSi2 that have been known widely. From the obtained crystalline phase, after the calculation of amorf Si3N4 and TiSi2 phase fraction, it is found that the optimum hardness can be reached when the fraction of a-Si3N4 phase around 8 wt.%