Mechanical Engineering Commons^™

A Sinteractive Ni-Bazr0.8Y0.2O3-Δ Composite Membrane For Hydrogen Separation, Shumin Fang, Siwei Wang, Kyle S. Brinkman, Fanglin Chen

Faculty Publications

BaZr_0.8Y_0.2O_3−δ (BZY) is an excellent candidate material for hydrogen permeation membranes due to its high bulk proton conductivity, mechanical robustness, and chemical stability in H₂O- and CO₂-containing environments. Unfortunately, the use of BZY as a separation membrane has been greatly restrained by its highly refractory nature, poor grain boundary proton conductivity, high number of grain boundaries resulting from limited grain growth during sintering, as well as low electronic conductivity. These problems can be resolved by the fabrication of a Ni–BZY composite membrane with large BZY grains, which requires the development …

Nuts & Bolts, Volume 2, Issue 2, Lance Todd, Julie Thomson, Louis Leviticus

Friends of the Larsen Tractor Museum

Museum Open House is a Success

The Passing of Museum Volunteer Larry Ehlers

Larsen Museum to Auction Twelve Tractors

Details an Estate Planning and Memorial Designation

Study Of Aluminum Honeycomb Sandwich Composite Structure For Increased Specific Damping, Aditi S. Joshi

Open Access Theses

The aluminum honeycomb sandwich composite structure is commonly used in the aerospace and automotive applications where high strength to weight ratio is desirable. However the poor performance of the aluminum honeycomb sandwich composite structure in terms of the vibration damping and the sound transmission makes their applications limited. Studying the effect of different structural modifications on the damping has become an interesting area of research in past few decades. The present study addresses the effect of adding a mass on the composite beam at various locations on the damping loss factors for the modes of vibration present in the frequency …

Towards A Sustainable Modular Robot System For Planetary Exploration, S. G. M. Hossain

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

This thesis investigates multiple perspectives of developing an unmanned robotic system suited for planetary terrains. In this case, the unmanned system consists of unit-modular robots. This type of robot has potential to be developed and maintained as a sustainable multi-robot system while located far from direct human intervention. Some characteristics that make this possible are: the cooperation, communication and connectivity among the robot modules, flexibility of individual robot modules, capability of self-healing in the case of a failed module and the ability to generate multiple gaits by means of reconfiguration. To demonstrate the effects of high flexibility of an individual …

Investigation Of The High-Temperature Redox Chemistry Of Sr2Fe1.5Mo0.5O6-Δ Via In Situ Neutron Diffraction, Daniel E. Bugaris, Jason P. Hodges, Ashfia Hug, W. Michael Chance, Andreas Heyden, Fanglin Chen, Hans-Conrad Zur Loye

Faculty Publications

Crystallographic structural changes were investigated for Sr₂Fe_1.5Mo_0.5O_6−δ, an electrode material for symmetric solid oxide fuel cells. The samples of this material were heated and cooled in wet hydrogen and wet oxygen atmospheres, to simulate the reducing and oxidizing conditions experienced under actual fuel cell operating conditions, and their structures and oxygen contents were determined using in situ powder neutron diffraction. The existence of a reversible tetragonal to cubic phase transition was established to occur between room temperature and 400 °C, both on heating and cooling in either oxygen or hydrogen. The …

An Assessment Of Flow Regime Maps And A Numerical Heat Transfer Correlation For The Stratified/Annular Regime Of Shear-Driven Internal Condensing Flows, Fnu Nikhil Shankar

Dissertations, Master's Theses and Master's Reports - Open

Several modern-day cooling applications require the incorporation of mini/micro-channel shear-driven flow condensers. There are several design challenges that need to be overcome in order to meet those requirements.

The difficulty in developing effective design tools for shear-driven flow condensers is exacerbated due to the lack of a bridge between the physics-based modelling of condensing flows and the current, popular approach based on semi-empirical heat transfer correlations. One of the primary contributors of this disconnect is a lack of understanding caused by the fact that typical heat transfer correlations eliminate the dependence of the heat transfer coefficient on the method of …

Computationally Efficient Representation Of Statistically Described Material Microstructure For Tractable Forming Simulations, Nicholas Landry

Honors Theses and Capstones

The purpose of this project is to reduce a large statistical distribution of metal microstructure orientations to a manageable distribution to be used in metal forming simulations. Microstructure sensitive simulations at the macro-scale are impractical, because with so many state variables associated with material microstructure data, these simulations are extremely computationally expensive.

The goal was to develop a framework to accurately model plastic material response while repre- senting the material microstructure in a more compact form, reducing 106 or more microstructure orientations to a significantly smaller statistical distribution of representative orientations. This will significantly increase the computational efficiency and make …

Influence Of Crystal Structure On The Electrochemical Performance Of A-Site-Deficient Sr1-SNb0.1Co0.9O3-Δ Perovskite Cathodes, Yinlong Zhu, Ye Lin, Xuan Shen, Jaka Sunarso, Wei Zhou, Shanshan Jiang, Dong Su, Fanglin Chen, Zongping Shao

Faculty Publications

The creation of A-site cation defects within a perovskite oxide can substantially alter the structure and properties of its stoichiometric analogue. In this work, we demonstrate that by vacating 2 and 5% of Asite cations from SrNb_0.1Co_0.9O_3-δ (SNC1.00) perovskites (Sr_1-sNb_0.1Co_0.9O_3-δ,s = 0.02 and 0.05; denoted as SNC0.98 and SNC0.95, respectively), a Jahn–Teller (JT) distortion with varying extents takes place, leading to the formation of a modified crystal lattice within a the perovskite framework. Electrical conductivity, electrochemical performance, chemical compatibility and microstructure of Sr_1-sNb_0.1Co …

Design, Fabrication, And Properties Of 2-2 Connectivity Cement/Polymer Based Piezoelectric Composites With Varied Piezoelectric Phase Distribution, Xu Dongyu, Cheng Xin, Sourav Banerjee, Huang Shifeng

Faculty Publications

The laminated 2-2 connectivity cement/polymer based piezoelectric composites with variedpiezoelectric phase distribution were fabricated by employing Lead Zirconium Titanate ceramicas active phase, and mixture of cement powder, epoxy resin, and hardener as matrix phase with a mass proportion of 4:4:1. The dielectric, piezoelectric, and electromechanical coupling properties of the composites were studied. The composites with large total volume fraction ofpiezoelectric phase have large piezoelectric strain constant and relative permittivity, and thepiezoelectric and dielectric properties of the composites are independent of the dimensional variations of the piezoelectric ceramic layer. The composites with small total volume fraction of piezoelectric phase have large …

Low Frequency Energy Scavenging Using Sub-Wave Length Scale Acousto-Elastic Metamaterial, Raiz U. Ahmed, Sourav Banerjee

Faculty Publications

This letter presents the possibility of energy scavenging (ES) utilizing the physics of acousto-elastic metamaterial (AEMM) at low frequencies (<∼3KHz). It is proposed to use the AEMM in a dual mode (Acoustic Filter and Energy Harvester), simultaneously. AEMM’s are typically reported for filtering acoustic waves by trapping or guiding the acoustic energy, whereas this letter shows that the dynamic energy trapped inside the soft constituent (matrix) ofmetamaterials can be significantly harvested by strategically embedding piezoelectric wafers in the matrix. With unit cell AEMM model, we experimentally asserted that at lower acoustic frequencies (< ∼3 KHz), maximum power in the micro Watts (∼35µW) range can be generated, whereas, recently reported phononic crystal based metamaterials harvested only nano Watt (∼30nW) power against 10KΩ resistive load. Efficient energy scavengers at low acoustic frequencies are almost absent due to large required size relevant to the acoustic wavelength. Here we report sub wave length scale energy scavengers utilizing the coupled physics of local, structural and matrix resonances. Upon validation of the argument through analytical, numerical and experimental studies, a multi-frequency energy scavenger (ES) with multi-cellmodel is designed with varying geometrical properties capable of scavenging energy (power output from ∼10µW – ∼90µW) between 0.2 KHz and 1.5 KHz acoustic frequencies.

Ni-Doped Sr2Fe1.5Mo0.5O6-Δ As Anode Materials For Solid Oxide Fuel Cells, Guoliang Xiao, Siwei Wang, Ye Lin, Zhibin Yang, Minfang Han, Fanglin Chen

Faculty Publications

10% Ni-doped Sr₂Fe_1.5Mo_0.5O_6-δ with A-site deficiency is prepared to induce in situ precipitation of B-site metals under anode conditions in solid oxide fuel cells. XRD, SEM and TEM results show that a significant amount of nano-sized Ni-Fe alloy metal phase has precipitated out from Sr_1.9Fe_1.4Ni_0.1Mo_0.5O_6-δ upon reduction at 800^◦C in H₂. The conductivity of the reduced composite reaches 29 S cm⁻¹ at 800^◦C in H₂. Furthermore, fuel cell performance of the composite anode Sr_{1.9 …}

Computationally Efficient Representation Of Statistically Described Material Microstructure For Tractable Forming Simulations, Nicholas Landry

Honors Theses and Capstones

The purpose of this project is to reduce a large statistical distribution of metal microstructure orientations to a manageable distribution to be used in metal forming simulations. Microstructure sensitive simulations at the macro-scale are impractical, because with so many state variables associated with material microstructure data, these simulations are extremely computationally expensive.

The goal was to develop a framework to accurately model plastic material response while representing the material microstructure in a more compact form, reducing 106 or more microstructure orientations to a significantly smaller statistical distribution of representative orientations. This will significantly increase the computational efficiency and make the …

Virtualized Welding Based Learning Of Human Welder Behaviors For Intelligent Robotic Welding, Yukang Liu

Theses and Dissertations--Electrical and Computer Engineering

Combining human welder (with intelligence and sensing versatility) and automated welding robots (with precision and consistency) can lead to next generation intelligent welding systems. In this dissertation intelligent welding robots are developed by process modeling / control method and learning the human welder behavior.

Weld penetration and 3D weld pool surface are first accurately controlled for an automated Gas Tungsten Arc Welding (GTAW) machine. Closed-form model predictive control (MPC) algorithm is derived for real-time welding applications. Skilled welder response to 3D weld pool surface by adjusting the welding current is then modeled using Adaptive Neuro-Fuzzy Inference System (ANFIS), and compared …

A Study Of Walkway Safety And Evaluation Of Tribological Test Equipment, Henry Thomas Baker

UNF Graduate Theses and Dissertations

A walkway tribometer measures the coefficient of friction between flooring material and a test foot. The value of the coefficient of friction is an indicator as to whether the flooring surface is slippery and has a propensity to cause slip and falls. This study determined that one style of tribometer, an XL Tribometer, mimics the heel-to-floor interaction of the human heel strike. High speed video footage revealed that the test foot strikes the surface and rotates so that full engagement occurs before sliding thus mimicking the affect of a human ankle. The test foot accelerates forward as would be expected …

Crack Growth Behavior Under Creep-Fatigue Conditions Using Compact And Double Edge Notch Tension-Compression Specimens, Santosh B. Narasimha Chary

Graduate Theses and Dissertations

The American Society for Testing and Materials (ASTM) has recently developed a new standard for creep-fatigue crack growth testing, E 2760-10, that supports testing compact specimens, C(T), under load controlled conditions. C(T) specimens are commonly used for fatigue and creep-fatigue crack growth testing under constant-load-amplitude conditions. The use of these specimens is limited to positive load ratios. They are also limited in the amount of crack growth data that can be developed at high stress intensity values due to accumulation of plastic and/or creep strains leading to ratcheting in the specimen. Testing under displacement control can potentially address these shortcomings …

Kolsky Bar Experiment For High-Rate Large Deformations Of Polycarbonate, Jason Gerald Vogeler

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Polycarbonate (PC) is a tough, transparent engineering thermoplastic. Its impact strength and ability undergo large plastic deformations without shatter make PC an ideal protective material for impact-resilient eyewear, aircraft windows and transparent armor. A good understanding of the response of this material to large deformations at high strain rates is critical for its utilization in these applications. To this end, a striker-less Kolsky bar device is employed in this work for the needed material characterization. The apparatus allow impulsive torsion and/or compression loadings with pulse durations sufficiently long for the plastic flow behavior to develop fully. Three new testing techniques …

Design Of An Automatic Wood Trimming Machine, Van Ho, Nicholas Maskal, Andrew Rutland

Mechanical Engineering

This final design report, prepared for Sunrise Arts by the Cal Poly design team Mahogany Automation, details the year-long process in which the team of three engineering students designed and built an automated wooden -plank edge trimming machine that incorporates anti-jamming and continuous loading features. The team has examined current woodworking machines and features available on the industrial and commercial market, and used these as guides along with device requirements set by the project sponsor, Bruce Palmer. The focus has been on designing the simplest and most cost effective device that allows operators to make production runs of wooden slats …

Kinematic Synthesis Of Planar, Shape-Changing, Rigid Body Mechanisms For Design Profiles With Significant Differences In Arc Length, Shamsul A. Shamsudin, Andrew P. Murray, David H. Myszka, James P. Schmiedeler

Mechanical and Aerospace Engineering Faculty Publications

This paper presents a kinematic procedure to synthesize planar mechanisms capable of approximating a shape change defined by a general set of curves. These “morphing curves,” referred to as design profiles, differ from each other by a combination of displacement in the plane, shape variation, and notable differences in arc length. Where previous rigid-body shape-change work focused on mechanisms composed of rigid links and revolute joints to approximate curves of roughly equal arc length, this work introduces prismatic joints into the mechanisms in order to produce the different desired arc lengths. A method is presented to iteratively search along the …

Experimental And Finite Element Studies Of Shock Transmission, Eldon Jerry Goddard

UNLV Theses, Dissertations, Professional Papers, and Capstones

Composite materials are more widely used today in engineering products than ever before. Shock transmission in jointed composite sections needs to be investigated to understand the affect of composite materials on the dynamic response of the system. There exists limited published work on transient shock propagation through composite sections. The aim of this study is to analyze the transient behavior of joints in composite materials subjected to low impact loads and to develop a computational model that provides an improved physics based shock model. The jointed connection will be investigated experimentally and using Finite Element Analysis (FEA). The bolted joint …

Heat Transfer Experiment: Energy Conservation, Ben Ward, Brett Wallace, Ryan Waltman

Mechanical Engineering

This proposal, prepared for the Mechanical Engineering Department by the HTEC design team will redesign and replace the current energy conversion lab that is inaccurate and out of date. The team will evaluate methods of energy conversion, specifically using braking systems, as well as existing labs in order to design an accurate and relatable experiment for this lab. The project team will work with Professor Kim Shollenberger in order to design an experiment that demonstrates energy conversion through the first law of thermodynamics while utilizing a common device that is practical in student’s lives. The final result of this project …

Ultrasonic Propagation And Scattering In Pearlitic Steel, Hualong Du

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Diffuse ultrasonic backscatter measurements have been especially useful for extracting microstructural information and for improving flaw detection in materials. In this dissertation, this approach is applied to inspection of railroad wheels. To improve the wear resistance, the tread surfaces of railroad wheels are usually quenched with water to increase the hardness. The pearlite phase of iron, characterized by alternating ferrite and cementite phases, is created by the quenching and the lamellar spacing within grains increases progressively from the quenched tread surface to deeper locations due to the non-uniform cooling rate. The quench depth is an important parameter governing the wheel …

Experimental Study On The Effect Of Air Flow On Soap Bubble Formation, John M. Davidson

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Soap bubbles are a common interfacial fluid dynamics phenomenon having applications such as buoyant hollow spherical fillers and flow visualization of large scale airflows. In contrast to the dynamics of liquid drops in gas and gas bubbles in liquid, the dynamics of soap bubbles has not been well documented, possibly because soap bubbles have gas-liquid-gas interfaces. Having the thin-liquid-film interface seems to alter the characteristics of the bubble/drop creation process. Thus, the main objective of this study is to experimentally examine how airflow develops and interacts with the soap liquid film as the film stretches and finally collapses to pinch-off. …

Large-Displacement Lightweight Armor, Eric C. Clough

Master's Theses

Randomly entangled fibers forming loosely bound nonwoven structures are evaluated for use in lightweight armor applications. These materials sacrifice volumetric efficiency in order to realize a reduction in mass versus traditional armor materials, while maintaining equivalent ballistic performance. The primary material characterized, polyester fiberfill, is shown to have improved ballistic performance over control samples of monolithic polyester as well as 1095 steel sheets. The response of fiberfill is investigated at a variety of strain rates, from quasistatic to ballistic, under compression, tension, and shear deformation to elucidate mechanisms at work during ballistic defeat. Fiberfill’s primary mechanisms during loading are fiber …

Load Path Uncertainty In A Wood Structure And The Effect On Structural Reliability, Wenqi Wang, Christopher D. Eamon

Civil and Environmental Engineering Faculty Research Publications

The roof truss bearing points of a light-framed wood house were instrumented with load cells. It was found that under dead load alone, symmetric and theoretically identical truss reactions have significant variation. A similar degree of reaction discrepancy was found under the application of uplift pressures caused by hurricane winds. Analysis revealed that the majority of this discrepancy is caused by inherent uncertainties in load path. Although uncertainties in load magnitude and material resistance are accounted for in design by use of appropriate load and resistance factors, load path is generally taken to be deterministic. In this study, load path …

Reliability Analysis Of Reinforced Concrete Columns Exposed To Fire, Christopher D. Eamon, Elin A. Jensen

Civil and Environmental Engineering Faculty Research Publications

A reliability analysis is conducted on reinforced concrete columns subjected to fire load. From an evaluation of load frequency of occurrence, load random variables are taken to be dead load, sustained live load, and fire temperature. Resistance is developed for axial capacity, with random variables taken as steel yield strength, concrete compressive strength, placement of reinforcement, and section width and height. A rational interaction model based on the Rankine approach is used to estimate column capacity as a function of fire exposure time. Various factors were considered in the analysis such as fire type, load ratio, reinforcement ratio, cover, concrete …

Active Dense Tensegrity Structure: A Novel Concept For Shape Morphing Structures, Zhiwei Wu, Thomas Siegmund

The Summer Undergraduate Research Fellowship (SURF) Symposium

Shape morphing is of relevance for advanced engineering systems such as future aerospace vehicles. Tensegrity structures, a structure comprised of a set of discontinuous compressed struts held together with a continuous web of tensioned cables, can function as the foundation of a shape morphing system (Keith et al, 2007). However, the classic tensegrity structures may not be ideal in all configurations because the space within the structure is not utilized. As an alternative, the present work proposes a dense tensegrity system as an assembly of cables carrying tensions only and polyhedral elements under compression only. An active dense tensegrity can …

Computer Simulation Study Of Slipper Lubrication In Hydraulic Machines, Jordyn B. Miller, Monika Ivantysynova

The Summer Undergraduate Research Fellowship (SURF) Symposium

Hydraulic pumps and motors are vital components used in many applications today. Specifically, the axial piston pump is important because it is reliable, relatively compact, and has a high horsepower-to-weight ratio. These features make this type of pump very advantageous in hydraulic systems. Maintaining proper lubrication between surfaces in an axial pump, such as the slipper and swashplate, is imperative in order to have smooth operation of the system and prevent metal-to-metal contact. The aim of this research is to find the optimal slipper design and fluid film thickness to simultaneously maintain a balanced pressure and decrease power loss in …

Crane Shaking Platform Design, Bixing Yan, Andrea Vacca

The Summer Undergraduate Research Fellowship (SURF) Symposium

Most of the control methodology of Mobile hydraulic crane is not as energy efficient as people think or want, and the desire to innovate novel, energy-efficient control strategy is the target of most hydraulic experts. To develop or test the control method under real road and off-road conditions, a platform that could simulate the movement and vibration of the crane truck is desired. To design and build the multi-operation platform, a design process includes brain storming, design selection, FEA (Fundamental Element Analysis), mechanical sizing, hydraulic sizing and Bill of Material is required and preferred. After going through all the steps …

Linear Controller Establishment For Displacement-Control Pump Switching System, Yangqiao Zheng, Monika Ivantysynova

The Summer Undergraduate Research Fellowship (SURF) Symposium

Displacement Controlled (DC) hydraulics system is booming recently due to its high efficiency and accurate controllability, while the surplus numbers of pumps restrains its further development. DC pump switch technique is a promising application to reduce the number of pumps as well as the cost products to promote DC hydraulics technique. It is necessary to support an innovative DC hydraulic pump switching system with a controller which would allow rapid and accurate estimation and adaptation for all the parameters, like pressures and velocities, in the system. Dynamics and Hydraulics characteristics have initially been investigated for a simplified DC pump switching …

An Investigation Of Phase-Change Effects During Rapid Compression Machine Experiments, Colin Banyon

Master's Theses (2009 -)

Rapid compression machines (RCMs) are well characterized laboratory scale devices capable of achieving internal combustion (IC) engine relevant thermodynamic environments. These machines are often used to collect ignition delay times as targets for gas-phase chemical kinetic fuel autoigntion models. Modern RCMs utilize creviced piston(s) to improve charge homogeneity and allow for an adequate validation of detailed chemistry mechanisms against experiments using computationally efficient, homogeneous reactor models (HRMs). Conventionally, experiments are preformed by introducing a premixed gas of fuel + oxidizer + diluent into the machine, which is compressed volumetrically via a piston. Experiments investigating low-vapor pressure fuels (e.g. diesels, biodiesels, …