Mechanical Engineering Commons^™

Balloon Borne Mars Research Platforms, Sean Michael Hancock

Mechanical & Aerospace Engineering Theses & Dissertations

Aerial platforms can fill a measurement gap between orbiters and rovers, providing planetary scale high resolution in situ measurements, access to scientifically interesting terrain that is either inaccessible or hazardous to rovers, and serve as a planet-wide delivery platforms to deploy surface probes and rovers to areas inaccessible given existing entry, descent, and landing systems. A permanent robotic outpost on the Martian surface can utilize locally-derived hydrogen as a lifting gas for balloon systems deployed from Mars. That approach can simplify the inflation and launch of aerial vehicles while allowing for a long duration deployment campaign that is not constrained …

Study Of Turbulence-Radiation Interaction In Hypersonic Turbulent Boundary Layers, L. (Lian) Duan, A. M. Feldick, M. P. Martín, M. F. Modest, D. A. Levin

Mechanical and Aerospace Engineering Faculty Research & Creative Works

In the paper, we conduct direct numerical simulations (DNS) to investigate the effect of turbulence-radiation interaction (TRI) in hypersonic turbulent boundary layers, representative of the Orion crew exploration vehicle (CEV) at peak heating condition during reentry. The radiative transfer equation (RTE) is solved using the tangent slab approximation. 1 The RTE solver is line-by-line (LBL) accurate, making use of a developed efficient spectral database 2 for spectral modeling. A multi-group full-spectrum correlated-k-distribution (FSCK) method 3 is used to reduce the number of RTE evaluations while preserving LBL accuracy. A nondimensional governing parameter to measure the significance of TRI is proposed, …

Assessment Of Turbulence-Chemistry Interaction In Hypersonic Turbulent Boundary Layers, L. (Lian) Duan, M. P. Martín

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Studies of the turbulence-chemistry interaction are performed in hypersonic turbulent boundary layers using direct numerical simulation flow fields under typical hypersonic conditions representative of blunt-body and slender body hypersonic vehicles, with super catalytic and noncatalytic wall conditions in pure air. Nondimensional governing parameters, the interaction Damköhler number and the interaction relative heat release, are proposed to measure the influence of turbulence-chemistry interaction on flow composition and temperature. Both a priori and posteriori studies are performed to assess the effect of turbulence-chemistry interaction on chemical production rates and mean and turbulent flow characteristics. It is found that the governing parameters provide …

Beading And Dimpling Techniques To Improve The Vibration And Acoustic Characteristics Of Plate Structures, Nabeel Taiseer Alshabtat

Dissertations

A method of improving the vibroacoustic characteristics of beams and plates is presented. This method is based on creating dimples or beads on the surface of the structures. The proposed method couples the finite element method with an optimization technique based on the genetic algorithm (GA). The improvement of the vibroacoustic characteristics of beams and plates is achieved by two separate strategies. The first strategy is optimizing the natural frequencies of beams and plates. The second strategy is minimizing the sound radiation from such vibrating structures. Optimizing the natural frequencies of some types of beams and simply supported plates by …

Dynamic Ergonomic Analysis And Simulation Of Fastening Operation, Akul Joshi

Doctoral Dissertations

"Operator performing fastening operation with powered hand-tools at awkward postures is subjected to external forces that may pose a risk of developing ergonomic injuries. For design of safe workplaces and selection of tools it is necessary to identify the probable causes of discomfort by simulating the work conditions and quantifying the risk factors. An ergonomic simulator is developed to simulate the fastening operation and quantify the effects of posture and force in fastening operation. The effect of dynamic forces is analyzed using two approaches. The first approach analyzes the effect of tool vibration while the second analyzes the hand-arm system …

Perch Landing Maneuvers And Control For A Rotating-Wing Mav, Jonathan Louis Lubbers

University of Kentucky Master's Theses

This thesis addresses flight control of the perch landing maneuver for micro-aerial vehicles. A longitudinal flight model is constructed for a pigeon-sized aircraft. In addition to a standard elevator control surface, wing-rotation also considered as a non-standard actuator for increasing low-speed aerodynamic braking. Optimal state and control trajectories for the perch landing maneuver are computed using commercial software. A neighboring optimal control law is then developed and implemented in a set of flight simulations. Simulations are run with both a quasisteady and an unsteady aerodynamic model. The effectiveness of wing rotation and of the neighboring optimal control law is discussed, …

A Shock Tube Technique For Blast Wave Simulation And Studies Of Flow Structure Interactions In Shock Tube Blast Experiments, Nicholas N. Kleinschmit

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Improvised explosive devices (IED’s) are widely used against US and allied forces fighting in Iraq and Afghanistan. Exposure to IED blast may cause blast-induced traumatic brain injury (bTBI). The injury mechanisms are however not well understood. A critical need in bTBI-related research is the ability to replicate the loading conditions of IED blast waves in a laboratory environment. In this work, experimental studies have been carried out to explore the use of the shock tube technique for generating air shock waves that mimic the temporal and spatial characteristics of free-field blast waves and to investigate the blast wave-test sample interactions …

A Comparative Verification Of Forecasts From Two Operational Solar Wind Models, Donald C. Norquist, Warner C. Meeks

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The solar wind (SW) and interplanetary magnetic field (IMF) have a significant influence on the near‐Earth space environment. In this study we evaluate and compare forecasts from two models that predict SW and IMF conditions: the Hakamada‐Akasofu‐Fry (HAF) version 2, operational at the Air Force Weather Agency, and Wang‐Sheeley‐Arge (WSA) version 1.6, executed routinely at the Space Weather Prediction Center. SW speed (V_sw) and IMF polarity (Bpol) forecasts at L1 were compared with Wind and Advanced Composition Explorer satellite observations. Verification statistics were computed by study year and forecast day. Results revealed that both models’ mean Vsw are …

An Investigation Of Initially Delaminated Composite Sandwich With Delamination Arrest Mechanism Under Buckling Loading, Tony D. Tran

Master's Theses

This thesis involves the development of a fiberglass-foam composite sandwich structure with the introduction of delamination arrestment keys; therefore, a study of an initially delaminated composite sandwich structure was the experimental analysis on multiple configurations in how the arrestment keys are placed.

The first part of this thesis research was to the experimental design and manufacturing of the composite sandwich plates. These plates were later cut down to the specific test dimensions and manufacturing processes for the composite sandwich plates and test specimens were created. The composite sandwich plates were manufactured using a vacuum resin infusion process. The dimensions of …

Bi-Material Attachment Through A Soft Tissue Interfacial System, Y. X. Liu, S. Thomopoulos, Victor Birman, J. S. Li, G. M. Genin

Mechanical and Aerospace Engineering Faculty Research & Creative Works

No abstract provided.

2-D Path Planning For Direct Laser Deposition Process, Swathi Routhu, Divya Kanakanala, Jianzhong Ruan, Xiaoqing Frank Liu, Frank Liou

Computer Science Faculty Research & Creative Works

The zigzag and offset path have been the two most popular path patterns for tool movement in machining process. Different from the traditional machining processes, the quality of parts produced by the metal deposition process is much more dependent upon the choice of deposition paths. Due to the nature of the metal deposition processes, various tool path patterns not only change the efficiency but also affect the deposition height, a critical quality for metal deposition process. This paper presents the research conducted on calculating zigzag pattern to improve efficiency by minimizing the idle path. the deposition height is highly dependent …

Earth Systems Lesson Plan: Size And Forces Of The Solar System, Getaway Special Team 2010

Education and Outreach

No abstract provided.

Physics Lesson Plan: How Far And Fast Does It Travel?, Getaway Special Team 2010

Education and Outreach

No abstract provided.

Elementary And Middle School Science Lesson Plan: Solid, Liquid, Gas, What Is It?, Getaway Special Team 2010

Education and Outreach

No abstract provided.

Uncertainty Quantification Integrated To Cfd Modeling Of Synthetic Jet Actuators, Srikanth Adya, Daoru Frank Han, Serhat Hosder

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The Point-Collocation Non-intrusive Polynomial Chaos (NIPC) method has been applied to a stochastic synthetic jet actuator problem used as one of the test cases in the CFDVAL2004 workshop to demonstrate the integration of computationally efficient uncertainty quantification to the high-fidelity CFD modeling of synthetic jet actuators. The test case included the simulation of an actuator generating a synthetic jet issued into quiescent air. The Point-Collocation NIPC method is used to quantify the uncertainty in the long-time averaged u and v-velocities at several locations in the flow field due to the uniformly distributed uncertainty introduced in the amplitude and frequency of …

Stochastic Optimal Control In Nonlinear Systems, Celestin Nkundineza

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Stochastic control is an important area of research in engineering systems that undergo disturbances. Controlling individual states in such systems is critical. The present investigation is concerned with the application of the stochastic optimal control strategy developed by To (2010) and its implementation as well as providing computed results of linear and nonlinear systems under stationary and nonstationary random excitations. In the strategy the feedback matrix is designed based on the achievement of the objectives for individual states in the system through the application of the Lyapunov equation for the system. Each diagonal element in the gain or associated gain …

"Pull-In" Of A Pre-Stressed Thin Film By An Electrostatic Potential: A 1-D Rectangular Bridge And A 2-D Circular Diaphragm, Gang Duan, Kai Tak Wan

Mechanical and Aerospace Engineering Faculty Research & Creative Works

A one-dimensional (1-D) rectangular pre-stressed thin film clamped at two opposite ends is actuated by an electrostatic voltage applied to a pad directly underneath. the pre-stress is allowed to be either tensile or compressive in nature. at a critical applied voltage, the film becomes unstable and makes direct contact with the pad, leading to "pull-in". an elastic model is constructed to account for the phenomenon over ranges of film pad gap and residual stress. the results compare favorably with finite element analysis (FEA) in literature and experimental data and possess distinct advantages over other available closed-form solutions. the model is …

Implementation Of A Conrad Probe On A Boundary Layer Measurement System, Charles Rocky Ulk

Master's Theses

This thesis presents the design, calibration, and performance evaluation of a type of two-hole pressure probe anemometer known as a Conrad probe, as well as its subsequent implementation on an autonomous, compact boundary layer measurement device and its first application for subsonic in-flight measurements of a swept wing boundary layer. Calibration of the Conrad probe was accomplished using two calibration functions and a non-nulling method for resolving in-plane flow velocity direction and magnitude over a range of ±30 degrees. This approach to calibration and application offered the advantages of rapid data acquisition with lower energy consumption than alternative methods for …

Investigations Of Femtosecond-Nanosecond Dual-Beam Laser Ablation Of Dielectrics, Cheng Hsiang Lin, Zheng Hua Rao, Lan Jiang, Wu Jung Tsai, Ping Han Wu, Chih Wei Chien, Shean Jen Chen, Hai Lung Tsai

Mechanical and Aerospace Engineering Faculty Research & Creative Works

We have conducted experimental investigations for the micromachining of dielectrics (fused silica) using an integrated femtosecond (is) and nanosecond (ns) dual-beam laser system at different time delays between the fs and ns pulses. We found that the maximum ablation enhancement occurs when the fs pulse is shot near the peak of the ns pulse envelope. Enhancements up to 13.4 times in ablation depth and 50.7 times in the amount of material removal were obtained, as compared to fs laser ablation alone. the fs pulse increases the free electron density and changes the optical properties of fused silica to have metallic …

Analytic Construction Of Periodic Orbits In The Restricted Three-Body Problem, Mohammed A. Ghazy

Mechanical & Aerospace Engineering Theses & Dissertations

This dissertation explores the analytical solution properties surrounding a nominal periodic orbit in two different planes, the plane of motion of the two primaries and a plane perpendicular to the line joining the two primaries, in the circular restricted three-body problem. Assuming motion can be maintained in the plane and motion of the third body is circular, Jacobi's integral equation can be analytically integrated, yielding a closed-form expression for the period and path expressed with elliptic integral and elliptic function theory. In this case, the third body traverses a circular path with nonuniform speed. In a strict sense, the in-plane …

Validating Module Heuristics On Large Scale Products, Rachel Day, Robert B. Stone, Katie Grantham Lough

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Decreasing time and costs is a major objective in many businesses today. Including modularity in the early design phases can effectively decrease time spent on and costs associated with a project. the task of identifying modules within a product early in the design process (when decisions are less expensive) is made less daunting by using the techniques of functional modeling and module heuristics. This paper discusses the results of the initial efforts to verify the module heuristics on large products (products with functional models consisting of more than 30 sub-functions) since the module heuristics were originally developed on small products. …

Functioncad: A Functional Modeling Application Based On The Function Design Framework, Robert L. Nagel, Kenneth L. Perry, Robert B. Stone, Daniel A. Mcadams

Mechanical and Aerospace Engineering Faculty Research & Creative Works

This paper presents a functional modeling application, Function CAD, based on integrated functional and process modeling within the Function Design Framework. Function CAD provides for mixed, hierarchical models of environment, process and function with relationships represented via flows of material, energy and signal. This paper discusses the technical details of the Function CAD software including its two major components: (1) the library, libFCAD, for handling the internal representation of the model and (2) the GUI for user-Based model manipulation and visualization. the application of Function CAD within a computational, function- based conceptual design process is discussed along with the plugin …

Prediction Of The Transport Properties Of A Polyatomic Gas, Zhi Liang, Hai-Lung Tsai

Mechanical and Aerospace Engineering Faculty Research & Creative Works

An Ab Initio Molecular Potential Model is Employed in This Paper to Show its Excellent Predictability for the Transport Properties of a Polyatomic Gas from Molecular Dynamics Simulations. a Quantum Mechanical Treatment of Molecular Vibrational Energies is Included in the Green and Kubo Integral Formulas for the Calculation of the Thermal Conductivity by the Metropolis Monte Carlo Method. using CO2 Gas as an Example, the Fluid Transport Properties in the Temperature Range of 300-1000 K Are Calculated Without using Any Experimental Data. the Accuracy of the Calculated Transport Properties is Significantly Improved by the Present Model, Especially for the Thermal …

A Natural Language To Component Term Methodology: Towards A Form Based Concept Generation Tool, Matt Robert Bohm, Robert B. Stone

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Over the last few decades design researchers have put forward theories and proposed methodologies that increase the chance that a design team will reliably arrive at the optimal solution to a given design problem. Studies, however, bear out that theories and methodologies alone will not guarantee an optimal or even good design solution. Instead, a breadth of knowledge across multiple engineering domains and the time and tools to thoroughly evaluate the design space are as important as any prescriptive design method. This work presents one of the underlying engineering technologies needed to leverage artificial intelligence approaches to thoroughly search the …

Ground Support Equipment For Northrop Grumman Massive Heat Transfer Experiment, Michael A. Manuel, Christopher J. Sparber, Greg A. Trent

Aerospace Engineering

California Polytechnic State University students designed, built, and certified ground support equipment for the Northrop Grumman Massive Heat Transfer Experiment. The Cal Poly design team built the 10000, 20000, and 30000 assemblies to meet Northrop Grumman requirements. The requirements included interface limitations, design load factors, delivery, and testing specifications. The design process consists of requirements generation, conceptual design, preliminary design, design reviews, manufacturing, and certification. The hardware was successfully completed and is used at the Johnson Space and Kennedy Space Center.

Measurement Of Refractive Index Change Of Optical Fiber Core Induced By Femtosecond Laser Scanning, Y. Han, T. Wei, Hai-Lung Tsai, Hai Xiao

Mechanical and Aerospace Engineering Faculty Research & Creative Works

We report a new method to measure the refractive index change in optical fiber core induced by femtosecond (fs) laser exposure. An in-line Fabry-Perot interferometer, serving as the measurement platform, is constructed on a commercial single-mode optical fiber by onestep femtosecond (fs) laser fabrication. A positive refractive index change is observed and measured accurately as the laser pulse energy surpasses the ablation threshold.

Observations Of Temporal Group Delays In Slow-Light Multiple Coupled Photonic Crystal Cavities, S. Kocaman, Xiaodong Yang, J. F. Mcmillan, M. B. Yu, D. L. Kwong, C. W. Wong

Mechanical and Aerospace Engineering Faculty Research & Creative Works

We demonstrate temporal group delays in coherently coupled high- Q multicavity photonic crystals, in an all-optical analog to electromagnetically induced transparency. We report deterministic control of the group delay up to 4x the single cavity lifetime in our room-temperature chip. Supported by three-dimensional numerical simulations and theoretical analyses, our multipump beam approach enables control of the multicavity resonances and intercavity phase, in both single and double transparency peaks. The standing-wave wavelength-scale photon localization allows direct scalability for chip-scale optical pulse trapping and coupled-cavity quantum electrodynamics.

Modeling The Momentum And Mass Transfer Within A Micro-Scale Polymer Electrolyte Membrane Fuel Cell For Flows Within The Slip Flow Regime, Sean Tamarun Goudy

Dissertations

Polymer Electrolyte Membrane (PEM) fuel cell systems are heterogeneous catalytic systems. Although there are many computational models that describe the behavior of PEM fuel cells, few simulate the catalyst surface concentration of reactant gases at the catalyst layer-membrane layer inteface. Most PEM fuel cell models make no distinction between the bulk concentration of reactants and the catalyst surface concentration of reactants. It is the surface concentration that is key when studying PEM fuel cell systems: the reactions occur at the surface of the catalyst.

In addition, few model the dynamics within the non-continuum flow region near the solid surfaces of …

Guidance And Navigation Linear Covariance Analysis For Lunar Powered Descent, Travis J. Moesser

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

A linear covariance analysis is conducted to assess closed-loop guidance, navigation, and control system (GN&C) performance of the Altair vehicle during lunar powered descent. Guidance algorithms designed for lunar landing are presented and incorporated into the closed-loop covariance equations. Navigation-based event triggering is also included in the covariance formulation to trigger maneuvers and control dispersions. Several navigation and guidance trade studies are presented demonstrating the influence of triggering and guidance and study parameters on the vehicle GN&C performance.

Hydrogen Fuel Cell Analysis: Lessons Learned From Stationary Power Generation Final Report, Scott E. Grasman, John W. Sheffield, Fatih Dogan, Sunggyu Lee, Umit O. Koylu, Angie Rolufs

Materials Science and Engineering Faculty Research & Creative Works

This study considered opportunities for hydrogen in stationary applications in order to make recommendations related to RD&D strategies that incorporate lessons learned and best practices from relevant national and international stationary power efforts, as well as cost and environmental modeling of pathways. The study analyzed the different strategies utilized in power generation systems and identified the different challenges and opportunities for producing and using hydrogen as an energy carrier. Specific objectives included both a synopsis/critical analysis of lessons learned from previous stationary power programs and recommendations for a strategy for hydrogen infrastructure deployment. This strategy incorporates all hydrogen pathways and …