Structural Materials Commons^™

Calculation Of Socket Depth For Circular Pipe Pier-Bearing Platform Socket Connection, Chen Jingli, Xiao Feng, Wang Zhigang, Wang Zhihai, Xu Yan

Journal of China & Foreign Highway

The minimum socket depth for circular pipe pier-bearing platform socket connection can be calculated according to Article C.0.3 in the Specifications for Design of Highway Precast Concrete Bridges (JTG/T 3365 -05—2022 ).In order to enable engineering designers to fully understand and correctly apply the calculation formula in this article,this paper first introduced the main technical features of the typical connection scheme,as well as the structural failure principles and objectives formulated in the specification of the typical connection scheme.Then,it briefly introduced the experimental research content and results of the typical connection scheme and explained the key construction measures and their functions …

Reliability Analysis Of Long‑Span Concrete Box Arch Bridge Under Temperature Effect Combinations, Zheng Junlin, Jiang Youbao, Zheng Xinhao, Lu Naiwei

Journal of China & Foreign Highway

The existing design methods for concrete arch bridge structures do not consider the random characteristics of the eccentricity generated by load effects and overlook the influence of stochastic eccentricity on structural reliability.To address this deficiency,a calculation model for eccentricity under temperature effect combinations was derived.The random characteristics of eccentricity for different sections of the main arch of concrete arch bridges and their sectional bearing capacities were analyzed under different load parameter combinations.By utilizing the Monte Carlo method,reliability indices were computed for different sections of the main arch and different load parameter combinations after considering the random characteristics of eccentricity.The results …

Preparation And Performance Of Emulsified Asphalt With High-Temperature Resistant And Wheel Sticking-Free Effects, Yan Han, Zha Xudong, Kang Xiaogang, Gong Yan, Zhang Zhengji, Zhang Wenshuai

Journal of China & Foreign Highway

To address the problem of wheel sticking at high temperatures in the construction process of existing wheel sticking-free emulsified asphalt of tack coat,this paper adopted the composite modification method of 70# and 15# matrix asphalt and waterborne polyurethane resin (WPR ) to prepare hard asphalt-WPR (HA-WPR )-modified emulsified asphalt in accordance with the high-temperature resistant and wheel sticking-free requirements.Through a series of laboratory tests,the technical performance,wheel sticking-free performance,and interlayer bonding performance of the emulsified asphalt were researched and compared with ordinary wheel sticking-free emulsified asphalt and ordinary emulsified asphalt tack coat oil.The results show that the technical performance of the …

Model Analysis Of Axial Compressive Mechanical Properties Of Concrete Column Constrained By Textile-Reinforced Engineered Cementitious Composites, Ma Gao, Wang Zhaoyang

Journal of China & Foreign Highway

In order to avoid the problem of matrix cracking in textile-reinforced concrete (TRC ),a reinforcement method of textile-reinforced engineered cementitious composites (ECC ),namely TRECC composed of textile and high-performance ECC was proposed.However,the research on the axial compressive mechanical properties of TRECC-constrained concrete in China and abroad is still insufficient,and there is a lack of reliable strength and ultimate strain analysis models.A total of 116 axial compression test results of TRC-constrained concrete columns and 125 axial compression test results of TRECC-constrained concrete columns were collected.The confinement mechanisms and failure modes of TRECC and TRC-constrained concrete were compared.Then,the strength models and ultimate …

Key Techniques For Constructing Flexible Geosynthetic Reinforced Soil Abutments, Yu Xiaoxiao, Xu Chao, Li Haoyu, Zuo Binli

Journal of China & Foreign Highway

The flexible geosynthetic reinforced soil (GRS ) abutments offer several advantages,including cost saving,reduced bridgehead misalignment,and good seismic performance,showing great potential for application in transportation engineering both in China and abroad.The flexible GRS abutment is essentially composed of a composite structure formed by closely spaced layers of geosynthetic reinforcement material,and the construction quality and load-bearing capacity are crucial to the success of the project.To ensure construction quality and study the construction process of flexible GRS abutments,a construction site monitoring method was adopted.Based on the experience from the construction of a vehicular overpass on the Wuwei ‒ Yuexi Expressway,the quality control measures …

Research On Mechanical Entry Excavation And Reinforcement Measures For Large Cross-Section Tunnel, Liang Xiao, Li Ke, Guo Hongyan, Hu Xuebing, Yao Chengrui

Journal of China & Foreign Highway

With the innovation of tunnel construction techniques and mechanical equipment,mechanical drilling and blasting for mountain tunnels have gradually developed.However,several challenges exist during the mechanical entry excavation for mountain tunnels,including the significant influence of geological factors,limited equipment adaptability,and constrained working space.This research,based on a specific tunnel project,utilized FLAC3D finite difference software to study the mechanical excavation method and auxiliary reinforcement measures for shallow-buried segments at the large cross-section tunnel portal.A comparative analysis was conducted on the displacement of surrounding rock,the stress of supporting structures,and the variation of plastic zones before and after tunnel face reinforcement for different advances per cycle and …

Application Research Of Bim Technology In Highway Prefabricated Bridge Scheme Design, Li Jinlong, Wang Xinnan, Liu Dongsheng, Chen Zhongzhi

Journal of China & Foreign Highway

At present,the highway bridge scheme requires continuous adjustments and upgrading due to iterative updates of design data and refined investigation of the surrounding environment of the bridge site.This paper upgraded the traditional route design software,developed a GIS-integrated platform,built a three-dimensional environment with design data as the core,and created a bridge scheme model through parametric intelligent design.It also evaluated and optimized the bridge scheme based on the integration of the bridge model and the surrounding environment.The results show that by using BIM technology,the forward design of a bridge scheme based on a three-dimensional environment is realized.This approach automates the scale statistics …

Partial Replacement Of Ordinary Portland Cement In Concrete By Limestone Calcined Clay (Lc2), Merna Abdelaziz

Theses and Dissertations

Limestone calcined clay (LC2) technique is a new approach that could address the environmental problem corelated with the construction industry due to its vital reliance on the ordinary Portland cement in its various applications. LC2 technique involves partial replacement of the OPC in concrete by limestone and calcined kaolinite clay with a ratio of 1:2 respectively. The main advantage of this technique is its high applicability due to its direct application on site. This study investigated the applicability of incorporating the LC2 technique in the construction industry. Three replacement percentages of OPC by LC2 in concrete were explored, which are …

Rheology And Early-Age Structure Development In Binary And Ternary Blends Modified With Novel Graphene Types, Sahil Surehali, Collin Gustafson, Sayee Srikarah Volaity, Ranjith Divigalpitiya, Aditya Kumar, Narayanan Neithalath

Materials Science and Engineering Faculty Research & Creative Works

Interest in the use of graphene to enhance the properties of cementitious materials is growing, but major impediments in implementation are the cost of graphene and changes in binder rheology attributable to these nanomaterials. This study explores the influence of novel, cost-effective, environment-friendly, and mass-producible graphene on the rheology and early-age structure development of cementitious binders. Two novel graphene types—fractal graphene (FG) and reactive graphene (RG)—are used in plain cement mixtures as well as those containing 30 % (by mass) of fly ash and/or limestone powder, at low dosages of ≤0.02 % by mass of binder. The early- and later-age …

Thermally Stimulated Stiffening And Fly Ash's Alkaline Activation By Ca(Oh)2 Addition Facilitates 3d-Printing, Xiaodi Dai, Sharu Bhagavathi Kandy, Narayanan Neithalath, Aditya Kumar, Mathieu Bauchy, Edward Garboczi, Torben Gaedt, Samanvaya Srivastava, Gaurav Sant

Materials Science and Engineering Faculty Research & Creative Works

3D-printing could offer substantial benefits to the construction industry including the fabrication of customized/bespoke components, eliminating formwork, and reducing material waste. Despite these advantages, control of the pumpability, extrudability, and buildability of 3D-printed concrete (3DPC) remains challenging. This study demonstrates how the use of fly ash (FA) enables enhanced thermal stiffening, and rapid alkali-activation in the presence of portlandite (Ca(OH)2, CH). In general, blends of CH and FA exhibit less structural build-up at low temperatures, but upon reaching a trigger temperature of 75 °C, these blends achieve rapid stiffening, at rates of ∼800 Pa/s. The rapid stiffening arises from the …

Effects Of Gypsum And Limestone On Early-Age Hydration And Strength Optimization In Belite Calcium Sulfoaluminate Cement, Sai Akshay Ponduru, Bryan K. Aylas-Paredes, Taihao Han, Advaith Neithalath, Narayanan Neithalath, Gaurav Sant, Aditya Kumar

Materials Science and Engineering Faculty Research & Creative Works

Belite calcium sulfoaluminate cement (CSAB), an alternative to Portland cement, exhibits excellent strength at both early and later ages. However, due to its high belite content, the carbon reduction from this type of cement is not sufficient when compared to other alternative cements. To further enhance CSAB's sustainability, this study investigates the performance of CSAB when partially replaced by low-carbon mineral additives (i.e., limestone and gypsum). The primary objective is to identify the optimal mixture design by incorporating gypsum and limestone to formulate a sustainable binder that maintains high compressive strength. The CSAB is replaced (with both additives) by up …

Simulation-Based Models For Postearthquake Response: A Survey And Research Directions, Abhijit Gosavi, Lauryn A. Spearing, Lesley H. Sneed

Engineering Management and Systems Engineering Faculty Research & Creative Works

Computer simulation is increasingly being used by emergency planners as a tool to improve disaster response given that it can model real-world scenarios, such as earthquakes. Although there has been an increase in simulation research focused on disaster response, much of this literature is from disparate fields and across disaster scenarios. To bridge this gap, this paper surveys simulation-based models for post-earthquake response from the year 2000 onward. Advantages of simulation over closed-form statistical models are discussed. Three main subproblems in post-earthquake response models are explored: (1) service distribution (e.g., food, water), (2) infrastructure restoration (at the building and transportation …

Integrating Off-Spec Scms Into Plc Blends, George A. Qubty

Civil Engineering Theses - Archive

Off-spec supplementary cementitious materials (SCMs) remain underutilized due to variability in reactivity and non-conformance with existing standards. This study evaluates the hydration behavior and fresh-state and mechanical performance of these materials in Portland limestone cement (PLC) systems. One Class F fly ash (FA), one bottom ash (BA), and two calcined clays (HACC and LACC) were evaluated as 20 % replacements to PLC. Hydration behavior was characterized using isothermal calorimetry and thermogravimetric analysis (TGA), while fresh-state and mechanical performance were assessed through flow table, Vicat setting time, load–crack mouth opening displacement (CMOD) flexural testing, and compressive strength testing. HACC increased compressive …

Reducing Friction In Machine Oil Via Cesium-Hybridized Graphene Oxide Quantum Dot Additives, Islam Gomaa, Sherief Elsoudy, Maryam Galal, Ahmed Azim

Nanotechnology Research Centre

Friction and wear are among the most common causes of energy loss and component failure in mechanical systems, accounting for around 20–30% of total global energy consumption. Conventional lubricants fail to provide consistent performance in harsh conditions due to inadequate additive dispersion, agglomeration, and restricted surface reactivity. Recent advances in nanomaterial-based lubricants have shown promise, but it remains difficult to achieve significant friction and wear reduction at low additive concentrations while preserving stability. In this study, we synthesized and tested cesium-hybridized graphene oxide quantum dots (Cs-GOQDs) as novel lubricant additives. When incorporated into machine oil at 0.1 wt%, Cs-GOQDs reduced …

Morphing Shape Metastructures Using The Hybrid Position Feedback Control And Bistable Structural Elements, Mehmet Simsek, Thomas E. Alberts, Onur Bilgen

Mechanical & Aerospace Engineering Faculty Publications

This research introduces a new multi-degree-of-freedom metastructure concept utilizing a hybrid position feedback controller. An arbitrary number of bistable segments, or structural elements, are connected serially or in parallel to form a distributed bistable structure, or a so-called metastructure. The hybrid controller, an unstable-then-stable second-order single-degree-of-freedom system, leverages the resonant mode of a bistable system to destabilize it and dynamically induce snap-through between equilibria. The metastructure inherits multiple bistable positions, maintaining equilibrium shapes without consuming power and enabling many equilibrium configurations. Two geometric configurations are proposed and analyzed using a modified hybrid feedback control approach, which rejects forces from neighboring …

Rheology Of Alumina Suspensions Subjected To Alternating Current Electric Fields For Freeze-Casting, Sivakumar Chithamallu, Ruksana Baby, Jacob L. Jones, Dipankar Ghosh

Mechanical & Aerospace Engineering Faculty Publications

Alternating current (AC) electric field can extrinsically tune freeze‐cast microstructure, originating from field‐induced increase in viscosity of ceramic suspensions. However, the changes that occur in a ceramic suspension and rheological behavior, ultimately affecting freeze‐cast microstructure, are not well understood. Moreover, the effects of AC electrokinetic forces and temperature on viscosity need to be decoupled. The viscosity and temperature of ceramic suspensions subjected to AC field and direct heating were measured, revealing that the increase in viscosity is due to AC dielectrophoretic forces rather than field‐induced heating of suspension. The shear thinning behavior of suspensions characterized using a power‐law model reveals …

Controlling Nitrogen Pickup During Induction Melting Of Ultrahigh-Strength Cr-Ni-Mo-V Steels, Kingsley T. Amatanweze, Viraj A. Athavale, Mario F. Buchely, Laura N. Bartlett, Ronald J. O'Malley, Daniel M. Field

Materials Science and Engineering Faculty Research & Creative Works

Nitrogen pickup during air induction melting can result in porosity and a loss of fracture toughness in ultrahigh-strength quenched and tempered steel castings. Nitrogen atoms are easily adsorbed into liquid steel upon exposure to the air, and argon shrouding alone has limited effectiveness. Previous studies have shown that proper charge sequencing and maintaining a high amount of dissolved oxygen in the melt prior to tapping and deoxidation can limit nitrogen pickup in the melt. In the current study, the effect of melt practice and charging procedure on nitrogen pickup was studied as a function of hold time in a series …

Parametric Analysis Of Water Jet Descaling Efficiency Of Reheated Continuously Cast Thin Slab, Tochukwu P. Ojiako, Mario F. Buchely, Simon Lekakh, Ronald J. O'Malley, Richard Osei, Taha Tayebali

Materials Science and Engineering Faculty Research & Creative Works

Efficient oxide scale removal is critical for maintaining surface quality and process efficiency in steel manufacturing. This study optimizes water jet descaling by evaluating the performance of flat and rotary jet nozzles under varying process parameters. Using a combined approach of experimental analysis and computational fluid dynamics, it investigates the influence of pressure (138–275 bar), lead angle (0°, 15°, 25°), working distance (50–100 mm), and spray angle (15°–25°) on descaling efficiency. Findings indicate that flat jet nozzles achieve superior performance at short working distances due to concentrated impact forces, while rotary jet nozzles sustain efficiency over extended distances through dynamic …

Effect Of Gating Design On Filling And Inclusion Control In An Al-Killed Cr-Mo-Ni Steel, Kingsley T. Amatanweze, Koushik Balasubramanian, Soumava Chakraborty, Viraj A. Athavale, Mario F. Buchely, Laura N. Bartlett, Ronald J. O'Malley, Daniel M. Field, Krista R. Limmer, Katherine M. Sebeck

Materials Science and Engineering Faculty Research & Creative Works

The effect of gating system design on the inclusion population and size distribution in an aluminum-killed low-alloy advanced high strength steel casting was studied. A mold with four different gating systems: pressurized and non-pressurized with side risers, naturally pressurized with a side riser, and naturally pressurized with a top riser, was designed using computational fluid dynamics and solidification software. The design allowed inclusion populations in castings produced with each gating system to be compared during the same pouring event. Samples taken from different positions just below the top surface of each casting were analyzed using an SEM/EDS system with automated …

Ultrafast Belite (Β-C2s) Production Using Biofuel-Based Combustion Synthesis, Shubham Agrawal, Sayee Srikarah Volaity, Oluwadamilare Charles Adesina, Bryan K. Aylas-Paredes, Taihao Han, Srinivas Kilambi, Aditya Kumar, Narayanan Neithalath

Materials Science and Engineering Faculty Research & Creative Works

This study presents a novel low-temperature, combustion synthesis (CS) approach for the rapid production of belite-rich cements. CS leverages the exothermic heat released from the combustion of biofuels such as lignin and/or biomass, intermixed with pelletized limestone and quartz. At an imposed furnace temperature of ∼700°C (as opposed to 1200°C–1300°C required in a conventional kiln), the source materials are rapidly transformed to belite, resulting in energy, emissions, and economic benefits. This work explores the influence of various process parameters, viz., fuel types and contents, airflow rate, porosity, holding temperature, and holding time on the efficiency of CS-based belite synthesis. Through …

Atomistic Calculations Characterizing Thermodynamic And Mechanical Properties Of High Entropy Alloys, Sarah O'Brien

Theses and Dissertations--Chemical and Materials Engineering

High entropy alloys (HEAs) are an exciting new class of materials. HEAs combine multiple elements in concentrations ranging from 5% to 35%. The large variation in concentrations increases the alloy’s entropy, stabilizing it. The stabilization is due to both an increased configurational entropy and increases the vibrational entropy when the alloy is at higher temperatures. This was seen for both MoNbTaW and FeNiMoW by combining the atomistic techniques: density functional theory (DFT) and density functional perturbation theory (DFPT). For MoNbTaW, the composition plays a large role in stabilizing the alloy over the configuration of elements. For the three-phase alloy, FeNiMoW, …

Design And Development Of A Rapid Tensile Quench Rig, Tyler Jewell, Justin Naylor

Williams Honors College, Honors Research Projects

This report outlines the design process and implantation of a tensile quenching rig that incorporated forced convection and a frequency generator. When any metal is quenched, a vapor barrier forms around it. When this happens, it limits the heat flux that may occur until the barrier turns into just nucleate boiling. The vapor barrier acts as an insulator and causes the heat flux to fluctuate, causing uneven hardening which would limit the use of some materials. To combat this effect, we are trying to use forced convection, and something new, which is adding high frequency waves into the quenching process. …

Characterization Of The Solid-State Bonding For Simulated Charge And Seam Welds In The Porthole Die Extrusion Process, Randall L. Bowers

Theses and Dissertations--Chemical and Materials Engineering

The isothermal (ISO-T) compression configuration is ideal for utilizing as a material input of flow stress at temperature and strain rate in models of the porthole die extrusion process due to the isothermal nature of the test. Micro-tensile testing was conducted to validate the solid-state welding integrity of the ISO-T samples at various temperatures and strain rates. Results of the mechanical testing were correlated with fractography and microstructural evaluations of the welds to confirm bonding behavior. Both clean interface conditions and oxidation and lubrication layers were evaluated to simulate the difference of seam and charge welds in the process. Results …

Combinatorial Thin Film Approach To Accelerate Materials Discovery: Development Of Nanoporous And Bulk Multi-Principal Element Alloys, Tibra Das Gupta

Theses and Dissertations--Chemical and Materials Engineering

Multi-principal element alloys (MPEAs) have garnered significant attention in materials science due to their potential for exhibiting a combination of desirable properties stemming from their unique configurational entropy. While early research focused on equiatomic compositions, recent studies have indicated that non-equiatomic MPEAs may offer superior mechanical performance. However, the identification of optimal non-equiatomic compositions remains challenging due to the vast compositional space and the reliance on time-consuming and computationally expensive methods. This dissertation presents a combinatorial thin film approach as a rapid and efficient strategy for discovering two types of materials: nanoporous and bulk MPEAs.

The first study explores the …

Sustainable Hemp Industrial Panels (Ship) And Its Industrial Possibilities For The Replacement Of Oriented Strand Board (Osb), Anthony Ollins

Masters Theses

This study explores the feasibility of using industrial hemp fiber to create composite panels—termed Sustainable Hemp Industrial Panels (SHIP) as a potential competitor for oriented strand board (OSB), a commonly used structural wood product. Given hemp's historical and environmental advantages, including rapid growth, carbon sequestration capacity, and material strength, this research investigates its performance when combined with Urea-Formaldehyde (UF) resin, and in a hybrid form with Southern Yellow Pine (SYP). Two hemp-based composites were produced and tested: one with hemp and UF, and another with hemp and SYP. Using a custom-built hydraulic press, composite panels were fabricated and subjected to …

Characterization And Optimization Of Sand And Tung Oil-Based Resins For Binder-Jet 3d Printing, Daniel I. Ajiola

College of Graduate Studies: Theses & Dissertations

Binder-jet 3D printing as a transformative technology in additive manufacturing, offers the ability to fabricate complex structures with diverse materials. This thesis investigates the use of a sustainable tung oil-based resin to create composites, exploring the potential for an eco-friendly alternative to synthetic binders.

The aim of this research is to develop and characterize a bio-based resin formulation, using tung oil as the primary binder, for application in binder-jet 3D printing with sand as the reinforcement. The resin formulation was prepared by combining tung oil, n-butyl methacrylate, divinylbenzene, and di-tert-butyl peroxide in precise proportions, ensuring a balanced mixture that supports …

Pulsed Arc Additive Manufacturing Of A Functionally Graded Er2209 Duplex Stainless Steel And Hsla-100 Structure: Morphology, Characterization, And Mechanical Performance, Stevens G. Hill Jr

College of Graduate Studies: Theses & Dissertations

Wire arc additive manufacturing is a process well suited to the efficient production of large structures. Duplex stainless steel exhibits high corrosion resistance and good strength which can be highly beneficial for industrial use. However, its use is limited due to its cost and complexity in controlling microstructure to achieve desired properties. In many cases, it can be highly beneficial to manufacture a component which uses specialty steel grades such as duplex stainless steel only where necessary, and utilizes more affordable, commonly available steels for reinforcement or bulk structural support. A functionally graded material satisfies these requirements by providing a …

Laser Ablation-Induced Corrosion Resistance For Molten Salt Equipment Materials Evaluated Utilizing Electrochemical And Spectroscopic Analysis, Peggy Milota

Theses and Dissertations

Advanced reactors and used nuclear fuel separation (i.e. pyroprocessing technology) utilize high temperature salt as a thermal storage medium as well as an ionic solution for electrochemical processes. The use of these aggressive molten chloride and fluoride mediums requires specific materials or additional system alterations to extend the lifetime and structural integrity of equipment due to corrosion. Some materials, in the presence of inherently impure salt, will corrode and form oxide films in a specific formation that decreases corrosion rate by electrochemically and physically preventing elemental movement to the material surface. This is referred to as a passivation layer. However, …

Reuse Of Calcium Carbonate (Caco3) Recovered From Discarded Carpets As Filler In Fiber-Reinforced Polymer (Frp) Composites, Roshan Devkota

Graduate Theses, Dissertations, and Problem Reports (ETD)

Over four billion pounds of carpet are discarded annually in the United States, making carpet waste a significant environmental concern. Calcium carbonate (CaCo₃) constitutes up to 45% of the mass of most synthetic carpets. Reusing this CaCo₃ as a filler in the rapidly growing fiber-reinforced polymer (FRP) industry, which is projected to reach USD 10.38 billion, presents a low-cost, practical approach to developing a market-based solution to post-consumer carpet waste.

This study investigates the reuse of CaCo₃ recovered from discarded carpet backing as a filler in FRP composites, focusing on its mechanical viability in comparison to virgin CaCo₃. The methodology …

Investigating The Effects Of Fly Ash On The Properties Of Silica-Deficient High Alumina Materials, Sai Akshay Ponduru

Doctoral Dissertations

This research is made up of five studies mainly focused on attaining sustainability in high alumina cements like calcium aluminate cement (CAC) and calcium sulfoaluminate belite cements (CSAB) by partially replacing them with additives and supplementary cementitious materials (SCMs) like fly ash (FA). The first study focused on understanding the reaction kinetics of CAC and FA binders at different replacement levels (i.e. between 10%-to-50% by mass) and their effect on mechanical properties. It was also shown that the reactive nature of FAs can be determined by calculating a single parameter called number of constraints (nc) derived from topological constraint theory. …