Structural Materials Commons^™

Study On Parameter Optimization Of Feet‐Lock Anchor Pipes Of Tunnels In Unconsolidated Formation, Tang Heqing, Jiang Xishan, Yang Peng

Journal of China & Foreign Highway

In order to give full play to the supporting role of the feet-lock anchor pipe in the tunnel with unconsolidated formation, it is necessary to obtain the optimal construction parameters of the feet-lock anchor pipe. Based on a tunnel project on the Huaping–Lijiang Expressway in Yunnan Province, this paper conducted numerical simulation and field test analysis. By comparing the arch subsidence and horizontal convergence of the supporting structure when the feet-lock anchor pipe with different parameters was constructed, the paper explored the characteristics and causes of the influence of construction parameters on the feet-lock effect. The results show that the …

Simulation Study On Flame Retardant Effect Of Warm‐Mixed Flame Retardant Pavement In Highway Tunnel

Journal of China & Foreign Highway

In order to obtain the flame retardant effect of the warm-mixed flame retardant asphalt pavement in highway tunnels, based on the finite element method and thermodynamics theory, the thermal analysis module of Ansys finite element software was used to study the flame retardant effect of ordinary asphalt pavement, flame retardant asphalt pavement, and warm-mixed flame retardant asphalt pavement under different fire scales. The maximum temperature of the three types of pavement increased with the increase in the fire scale. Under any fire scale, the flame retardant effect of the warm-mixed flame retardant asphalt pavement was increased by 4.9%–8.5% compared with …

Installation Construction Technology Of Composite Girder Cable‐Stayed Bridge Superstructure In Deep‐Cutting Gorge, Ren Lei, Lu Liang, Dong Zhengliang

Journal of China & Foreign Highway

In view of the installation problems of superimposed beam cable-stayed bridge across the deep canyon, this paper studied the superimposed beam lifting, transport on beam, and superimposed beam installation and proposed three kinds of lifting technology with tower truss crane, beam lifting door crane, and large tower crane, as well as two kinds of installation technology including piecemeal assembly by full rotating deck crane and whole segment assembly truss deck crane. It also made a relative comparative analysis, solving the difficulty in vertical lifting on such bridges and providing a reference for the construction of the same type of cable-stayed …

Experiment Research Of High Pressure Jet Grouting Pile On Ultra‐Shallow Buried Tunnel In Strong Weathered Stratum, Lu Liyang, Liu Huan, Li Pinpin

Journal of China & Foreign Highway

By taking the ultra-shallow buried construction of Xinwu Tunnel in Luoding–Xinyi Expressway in Guangdong Province as the engineering background, the key construction parameters and formation reinforcement effect of high-pressure rotary churning pile in ultra-shallow buried tunnel surrounding rock of fully weathered strata were compared. The results show that: ① slurry pressure, rotary churning speed, and lifting speed have obvious effects on the static load bearing capacity of a single pile. Under the same static load condition, greater slurry pressure indicates a lower cumulative settlement value of a single pile and a smaller increase in cumulative settlement value, and the change …

Study On Anti‐Scattering Performance Of Asphalt Concrete On Aggregate Scattering Pavement Of Highway, Yang Siyuan, Chen Guiliang

Journal of China & Foreign Highway

Due to the lack of quantitative evaluation methods for aggregate scattering degree of expressway asphalt pavement in China and abroad, according to the disease characteristics of surface layer spalling, this paper adopted the Cantabro standard dispersion test to sample the concrete of the section with aggregate scattering of Huangqunan Expressway (G3) in Zhejiang Province. The dispersion impact damage modes of the mixture with different severity were analyzed, and the anti-dispersion performance of concrete was evaluated by mass loss rate and water absorption rate. The results show that aggregate scattering will reduce the density of the concrete structure at the surface …

Variable Speed Limit Control Method For Highway Under Dense Fog, Sun Jiancheng, Qiao Jiaxing

Journal of China & Foreign Highway

In order to solve the problem of traffic safety on expressways under dense fog and change the original fixed speed limit measures, a variable speed limit control method based on the safe allowable speed was proposed. The speed limit value was calculated based on the regulations in road traffic safety law on the speed under dense fog by considering that the traffic law does not mention the road alignment conditions, road conditions, and other factors, and the monitor data was used to approximate replace the data of individual vehicles for data optimization, and the safe speed and safe distance of …

Application Of Digital Image Processing In Cracks Of Concrete Pavement, Gao Fan, He Chunguang, Wang Pengzhang, Qin Yanping, Duo Huaqiong

Journal of China & Foreign Highway

The image obtained by using the traditional crack detection method of concrete pavement has some problems, such as low contrast and high noise, which makes it difficult to meet the requirements of modern road engineering management or non-destructive testing. In order to eliminate the interference in crack images, digital image processing technology was used to improve the image quality through computers. This paper took digital image processing as the core and introduced its development and application in pavement cracks. Based on the research progress and achievements of digital image processing on pavement cracks in recent years, the principles and characteristics …

Design And Experimental Study On Special Spherical Support Of Pingtang Bridge, Tang Zhi, Ma Baihu, Du Bin, Xu Xiangdong, Xia Junyong

Journal of China & Foreign Highway

The vertical bearing capacity of the 16# pier of Pingtang Bridge is 10 000 kN, and the horizontal bearing capacity along the bridge is 12 000 kN, which is 120% of the vertical bearing capacity. The support angle needs to reach the technical parameter requirements of 0.05 rad, which far exceeds the requirements of 10–40% horizontal force of conventional highway supports. According to the specific engineering situation, a new type of support with a large horizontal bearing capacity was designed. Firstly, the finite element model of the support was established to analyze the mechanical properties of the support, and the …

Study On Practical Method Of Safety Assessment For Bridges Under Heavy‐Cargo Transportation, Jiang Xu, Wang Wanfeng, He Zhensheng, Gao Xuefeng

Journal of China & Foreign Highway

In order to meet the requirements of the industry for the high efficiency, safety, and reliability of the traffic safety assessment of heavy-duty vehicles, this paper proposed a method that combined a real-time monitoring system with a finite element method for the traffic safety assessment of heavy-duty vehicles on bridges and verified the method through practical projects. The paper evaluated the bridge’s technical condition level before the heavy-duty vehicle passes and determined the resistance reduction factor considering the bridge’s technical condition level. The finite element analysis model of the bridge was established, and the reliability of the model was verified …

Study On Pavement Performance Of Waterborne Epoxy Emulsified Asphalt And Its Application In Micro‐Surface, Jiang Hai, Liu Dachang

Journal of China & Foreign Highway

In order to improve the pavement performance at micro-surface, waterborne epoxy resin was used to modify the emulsified asphalt, and the compatibility, microstructure, mechanical properties, rheological properties, and pavement performance of mixtures of the modified emulsified asphalt were studied. The storage stability test shows that the epoxy emulsion has good compatibility with emulsified asphalt. With the increase in waterborne epoxy resin content, the modified emulsified asphalt tends to form an epoxy resin-dominated skeleton structure. At the same time, with the increase in waterborne epoxy resin content, the adhesion and mechanical properties of emulsified asphalt and aggregate are significantly improved. At …

Precious Plastics - Plastic Brick Machine Fabrication, Timothy Ukaobasi Kanu, Evi Paraskevi Troulis

Architectural Engineering

The goal of this research is to determine the structural parameters of the recycled plastic polypropylene when molded into bricks resembling CMU blocks. To accomplish this, three mechanisms had to be assembled: the shredder, the injector, and the 1x1 mold. A tensile and compression test were to be performed on the plastic brick, and the values would be used to compare the tensile and compressive strength of PP plastic bricks, as well as their modulus of elasticity and stress vs. Strain performance. These values would be analyzed to determine whether it would be feasible to build an entire plastic wall. …

Atomistic Simulation Studies Of Thin Film Growth And Plastic Deformation In Metals And Metal/Ceramic Nanostructures, Reza Namakian

LSU Doctoral Dissertations

Despite the significant improvements in manufacturing and synthesis processes of metals and ceramics in the past decades, there are still areas in which the procedure is still frequently more of an art or skill rather than a science. Therefore, systematic and combined experimental and computational studies are required to facilitate the development of techniques that offer thorough understanding of the events taking place during manufacturing and synthesis processes. With regard to these issues, it is paramount to address microscale characterizations and atomic scale understanding of the events during fabrication processes. One of the focuses of this study is unraveling fundamental …

Freespan Analysis For Subsea Pipeline Integrity Management Strategy, Nurul Hadi, Muhammad Helmi, Edo Cathaputra, Dedi Priadi, Donanta Dhaneswara

Journal of Materials Exploration and Findings

Abstract. Over a rough seabed or on seabed subject to scour, freespans can occur when contact between a subsea pipeline and the seabed is lost over an acceptable distance. When this exceeds the allowable freespan length, design stresses can be exceeded, and a vortex induced vibration (VIV) response can be initiated, resulting in the risk of fatigue failure. If this is not predicted and controlled properly, it will affect pipeline integrity, leading to expensive rectification and intervention work. Freespan analysis consisted primarily of a screening check in which the as-found freespans from Remotely Operated Vehicle (ROV) or multibeam Side …

Architecture Of Heptagonal Metallo-Macrocycles Via Embedding Metal Nodes Into Its Rigid Backbone, A.M.Shashika D. Wijerathna, He Zhao, Qiangqiang Dong, Qixia Bai, Zhiyuan Jiang, Jie Yuan, Jun Wang, Mingzhao Chen, Markus Zirnheld, Rockwell T. Li, Yuan Zhang, Yiming Li, Pingshan Wang

College of Sciences Posters

Metal-organic macrocycles have received increasing attention not only due to their versatile applications such as molecular recognition, compounds encapsulation, anti-bacteria and others, but also for their important role in the study of structure-property relationship at nano scale. However, most of the constructions utilize benzene ring as the backbone, which restricts the ligand arm angle in the range of 60, 120 and 180 degrees. Thus, the topologies of most metallo-macrocycles are limited as triangles and hexagons, and explorations of using other backbones with large angles and the construction of metallo-macrocycles with more than six edges are very rare.

In this study, …

A Deep Learning-Informed Design Scheme For Shear Friction At Concrete-To-Concrete Interface: Recommendations For Inclusion In Aashto Lrfd Guidelines, Tarutal Ghosh Mondal, Nikkolas Edgmond, Lesley Sneed, Genda Chen

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Recent advancements in construction technology have led to high-strength concrete and steel. However, these developments have depreciated the accuracy of the design equations in current provisions, which were based on normal-grade materials. To fill such a research gap, this study presents a novel deep learning-based computation scheme that can replace the current design provisions by virtue of its superior accuracy and reliability. The proposed approach exploits Neural Additive Models (NAMs) in which geometric and material properties associated with a normal weight concrete-to-concrete shear interface are inputted to individual neural network blocks. The outputs of the individual blocks are linearly combined …

Investigation Of Fiber Orientation And Mechanical Properties Of Pyrolysis Recycled Carbon-Fiber Reinforced Thermoset Composite, Reva N. Simmons, Harry Lee, Garam Kim

Discovery Undergraduate Interdisciplinary Research Internship

With increasing demand of carbon fiber reinforced fiber thermoset composites, establishing a sustainable cycle for these materials becomes crucial. Pyrolysis is a process of reclaiming carbon fiber from thermoset composites by thermally degrading the polymer at high temperatures allowing the fibers to be extracted. Carbon fiber reclaimed through current pyrolysis processes for thermoset composites typically loses its original shape and orientation, making it difficult to reorganize the fibers. This study investigated the feasibility of maintaining the fiber orientations for continuous fiber reinforced thermoset composite during pyrolysis by stitching the carbon fiber layup to a conformable copper mesh during the manufacturing …

Investigation Of Microstructurally Dependent Mechanical Properties Of Cold Sprayed Copper Using Correlative Microscopy, Quintin Otto

UNF Graduate Theses and Dissertations

This project employs multi-instrument materials characterization to analyze material made with the “Cold Spray” additive manufacturing process. Cold spray is an emerging additive manufacturing technique with unique benefits resulting from its low temperature adhesion process induced by plastic deformation. Metallic powder collides at high speeds creating three dimensional materials and coatings without the need for melting. Copper cold sprayed specimens were analyzed using a series of imaging techniques to characterize the microstructure at varying levels of detail and magnification. Scanning electron microscopy and electron back scattered diffraction were paired with microhardness testing to generate a correlative comparison between microstructure and …

Application Of Multi-Scale Computational Techniques To Complex Materials Systems, Mujan N. Seif

Theses and Dissertations--Chemical and Materials Engineering

The applications of computational materials science are ever-increasing, connecting fields far beyond traditional subfields in materials science. This dissertation demonstrates the broad scope of multi-scale computational techniques by investigating multiple unrelated complex material systems, namely scandate thermionic cathodes and the metallic foam component of micrometeoroid and orbital debris (MMOD) shielding. Sc-containing "scandate" cathodes have been widely reported to exhibit superior properties compared to previous thermionic cathodes; however, knowledge of their precise operating mechanism remains elusive. Here, quantum mechanical calculations were utilized to map the phase space of stable, highly-faceted and chemically-complex W nanoparticles, accounting for both finite temperature and chemical …

Predicting Compressive Strength And Hydration Products Of Calcium Aluminate Cement Using Data-Driven Approach, Sai Akshay Ponduru, Taihao Han, Jie Huang, Aditya Kumar

Electrical and Computer Engineering Faculty Research & Creative Works

Calcium aluminate cement (CAC) has been explored as a sustainable alternative to Portland cement, the most widely used type of cement. However, the hydration reaction and mechanical properties of CAC can be influenced by various factors such as water content, Li₂CO₃ content, and age. Due to the complex interactions between the precursors in CAC, traditional analytical models have struggled to predict CAC binders' compressive strength and porosity accurately. To overcome this limitation, this study utilizes machine learning (ML) to predict the properties of CAC. The study begins by using thermodynamic simulations to determine the phase assemblages of …

Hdd Dataset: Optimising Retrofitted Insulation For Irish Residential Building Walls, Rakshit D. Muddu, Aimee Byrne, Anthony James Robinson

Datasets

In this study, a thermal-economic analysis was conducted to determine the optimum insulation thickness of retrofitted insulation walls in different regions in Ireland. This was based on the Heating Degree Day method (HDD). This dataset contains optimum insulation thickness, payback period, cost savings and carbon emission for all 25 counties in the Republic of Ireland

Fem Eem Dataset: Optimising Retrofitted Insulation For Irish Residential Building Walls, Rakshit D. Muddu, Aimee Byrne, Anthony Robinson Dr.

Datasets

A large number of combinations of Irish wall types, insulation materials, and heating fuel types were produced to compare the multiple variables which influence Optimal Insulation Thickness values. The total cost (TC) and carbon emission (CE) at optimum insulation thickness (OIT) for all combinations of insulation material and three types of fuel are considered. The dataset presents OIT for solid wall, cavity wall and cavity block wall types located in Monaghan, Dublin, and Kerry.

Predicting Dissolution Kinetics Of Tricalcium Silicate Using Deep Learning And Analytical Models, Taihao Han, Sai Akshay Ponduru, Arianit Reka, Jie Huang, Gaurav Sant, Aditya Kumar

Electrical and Computer Engineering Faculty Research & Creative Works

The dissolution kinetics of Portland cement is a critical factor in controlling the hydration reaction and improving the performance of concrete. Tricalcium silicate (C₃S), the primary phase in Portland cement, is known to have complex dissolution mechanisms that involve multiple reactions and changes to particle surfaces. As a result, current analytical models are unable to accurately predict the dissolution kinetics of C₃S in various solvents when it is undersaturated with respect to the solvent. This paper employs the deep forest (DF) model to predict the dissolution rate of C₃S in the undersaturated solvent. The …

Deep Reinforcement Learning For Approximate Policy Iteration: Convergence Analysis And A Post-Earthquake Disaster Response Case Study, Abhijit Gosavi, L. (Lesley) H. Sneed, L. A. Spearing

Engineering Management and Systems Engineering Faculty Research & Creative Works

Approximate Policy Iteration (API) is a Class of Reinforcement Learning (RL) Algorithms that Seek to Solve the Long-Run Discounted Reward Markov Decision Process (MDP), Via the Policy Iteration Paradigm, Without Learning the Transition Model in the Underlying Bellman Equation. Unfortunately, These Algorithms Suffer from a Defect Known as Chattering in Which the Solution (Policy) Delivered in Each Iteration of the Algorithm Oscillates between Improved and Worsened Policies, Leading to Sub-Optimal Behavior. Two Causes for This that Have Been Traced to the Crucial Policy Improvement Step Are: (I) the Inaccuracies in the Policy Improvement Function and (Ii) the Exploration/exploitation Tradeoff Integral …

Development Of Inconel 718f And Inconel 718e Powders For Parts Manufacturing Utilizing Binder Jet Three-Dimensional Printing And Compressed Pellet Methods, Duncan Eric Manor Ii

Graduate Theses, Dissertations, and Problem Reports (ETD)

Alloy Inconel 718 is a Ni based superalloy used for high temperature applications including turbine blades, turbocharger rotors and nuclear reactors. Inconel 718 is a popular commercial atomized powder that has limitations in performance for use in additive manufacturing applications due to poor part quality and efficiency of current fabrication methods. Developing new compositions and additive manufacturing (AM) methodologies of IN718 is critical to improve the quality and the efficiency of IN718 parts manufacturing. Developing new additive manufacturing methodology that produces higher quality parts made of IN718 as compared to current methods has the potential to greatly impact industry, academia, …