Structural Materials Commons^™

Experiment Research Of High Pressure Jet Grouting Pile On Ultra‐Shallow Buried Tunnel In Strong Weathered Stratum, Lu Liyang, Liu Huan, Li Pinpin

Journal of China & Foreign Highway

By taking the ultra-shallow buried construction of Xinwu Tunnel in Luoding–Xinyi Expressway in Guangdong Province as the engineering background, the key construction parameters and formation reinforcement effect of high-pressure rotary churning pile in ultra-shallow buried tunnel surrounding rock of fully weathered strata were compared. The results show that: ① slurry pressure, rotary churning speed, and lifting speed have obvious effects on the static load bearing capacity of a single pile. Under the same static load condition, greater slurry pressure indicates a lower cumulative settlement value of a single pile and a smaller increase in cumulative settlement value, and the change …

Study On Anti‐Scattering Performance Of Asphalt Concrete On Aggregate Scattering Pavement Of Highway, Yang Siyuan, Chen Guiliang

Journal of China & Foreign Highway

Due to the lack of quantitative evaluation methods for aggregate scattering degree of expressway asphalt pavement in China and abroad, according to the disease characteristics of surface layer spalling, this paper adopted the Cantabro standard dispersion test to sample the concrete of the section with aggregate scattering of Huangqunan Expressway (G3) in Zhejiang Province. The dispersion impact damage modes of the mixture with different severity were analyzed, and the anti-dispersion performance of concrete was evaluated by mass loss rate and water absorption rate. The results show that aggregate scattering will reduce the density of the concrete structure at the surface …

Variable Speed Limit Control Method For Highway Under Dense Fog, Sun Jiancheng, Qiao Jiaxing

Journal of China & Foreign Highway

In order to solve the problem of traffic safety on expressways under dense fog and change the original fixed speed limit measures, a variable speed limit control method based on the safe allowable speed was proposed. The speed limit value was calculated based on the regulations in road traffic safety law on the speed under dense fog by considering that the traffic law does not mention the road alignment conditions, road conditions, and other factors, and the monitor data was used to approximate replace the data of individual vehicles for data optimization, and the safe speed and safe distance of …

Application Of Digital Image Processing In Cracks Of Concrete Pavement, Gao Fan, He Chunguang, Wang Pengzhang, Qin Yanping, Duo Huaqiong

Journal of China & Foreign Highway

The image obtained by using the traditional crack detection method of concrete pavement has some problems, such as low contrast and high noise, which makes it difficult to meet the requirements of modern road engineering management or non-destructive testing. In order to eliminate the interference in crack images, digital image processing technology was used to improve the image quality through computers. This paper took digital image processing as the core and introduced its development and application in pavement cracks. Based on the research progress and achievements of digital image processing on pavement cracks in recent years, the principles and characteristics …

Design And Experimental Study On Special Spherical Support Of Pingtang Bridge, Tang Zhi, Ma Baihu, Du Bin, Xu Xiangdong, Xia Junyong

Journal of China & Foreign Highway

The vertical bearing capacity of the 16# pier of Pingtang Bridge is 10 000 kN, and the horizontal bearing capacity along the bridge is 12 000 kN, which is 120% of the vertical bearing capacity. The support angle needs to reach the technical parameter requirements of 0.05 rad, which far exceeds the requirements of 10–40% horizontal force of conventional highway supports. According to the specific engineering situation, a new type of support with a large horizontal bearing capacity was designed. Firstly, the finite element model of the support was established to analyze the mechanical properties of the support, and the …

Study On Practical Method Of Safety Assessment For Bridges Under Heavy‐Cargo Transportation, Jiang Xu, Wang Wanfeng, He Zhensheng, Gao Xuefeng

Journal of China & Foreign Highway

In order to meet the requirements of the industry for the high efficiency, safety, and reliability of the traffic safety assessment of heavy-duty vehicles, this paper proposed a method that combined a real-time monitoring system with a finite element method for the traffic safety assessment of heavy-duty vehicles on bridges and verified the method through practical projects. The paper evaluated the bridge’s technical condition level before the heavy-duty vehicle passes and determined the resistance reduction factor considering the bridge’s technical condition level. The finite element analysis model of the bridge was established, and the reliability of the model was verified …

Study On Pavement Performance Of Waterborne Epoxy Emulsified Asphalt And Its Application In Micro‐Surface, Jiang Hai, Liu Dachang

Journal of China & Foreign Highway

In order to improve the pavement performance at micro-surface, waterborne epoxy resin was used to modify the emulsified asphalt, and the compatibility, microstructure, mechanical properties, rheological properties, and pavement performance of mixtures of the modified emulsified asphalt were studied. The storage stability test shows that the epoxy emulsion has good compatibility with emulsified asphalt. With the increase in waterborne epoxy resin content, the modified emulsified asphalt tends to form an epoxy resin-dominated skeleton structure. At the same time, with the increase in waterborne epoxy resin content, the adhesion and mechanical properties of emulsified asphalt and aggregate are significantly improved. At …

Crack Control And Bond Performance Of Alternative Coated Reinforcements In Concrete, Sachin Sreedhara

All Dissertations

Concrete cracking in structures is a ubiquitous problem which can lead to the deterioration of the structure. Other than affecting the strength aspect of a structure, cracking impacts the serviceability criteria as well. Although cracking phenomenon in any structure is highly inevitable, it has to be minimized in order to maintain a structure’s life effectively. Cracking in reinforced concrete structures is related to the bond strength developed between the bar and the concrete. It also depends on an ability of the bar to resist the stresses due to shrinkage to minimize the crack. Another important aspect is the resistance offered …

Enhancement Of Asphalt Performance By Graphene-Based Bitumen Nanocomposites, Sara Moghtadernejad, Ehsan Barjasteh, Ren Nagata, Haia Malabeh

Mineta Transportation Institute

As the State of California continues to grow, demand for enhanced infrastructure such as roadways and highways escalates. In view of the current average highway lifespan of 15–20 years, the improvement of asphalt binders leads to material sustainability by decreasing required maintenance and increasing the lifespan of roadways. In the present investigation, enhancement of asphalt binder properties was achieved by different methods of mixing varying compositions of graphene nanoparticles with an SBS polymer and asphalt binder. Additionally, experimental evaluation and comparison of the rheological and mechanical properties of each specimen is presented. Graphene nanoparticles have attracted great curiosity in the …

Structural Identification And Damage Detection In Bridges Using Wave Method And Uniform Shear Beam Models: A Feasibility Study, Mehran Rahmani, Manan Naik

Mineta Transportation Institute

This report presents a wave method to be used for the structural identification and damage detection of structural components in bridges, e.g., bridge piers. This method has proven to be promising when applied to real structures and large amplitude responses in buildings (e.g., mid-rise and high-rise buildings). This study is the first application of the method to damaged bridge structures. The bridge identification was performed using wave propagation in a simple uniform shear beam model. The method identifies a wave velocity for the structure by fitting an equivalent uniform shear beam model to the impulse response functions of the recorded …

Laboratory Testing And Mechanistic Analysis Of Treated Subgrade Soils, Hari Kumar Reddy Yarrapureddi

Civil Engineering Theses

Calcium-based stabilizing agents such as cement and lime have been extensively used to improve the engineering properties of base and subgrade layers of pavement systems. Recently, polymers and chemical stabilizers have become popular due to cost efficiency, ease of application, and fast curing times. In this study, California Bearing Ratio (CBR) values of polymer and chemical treated soils were compared with the CBR values of soils treated with conventional stabilizers. Parametric sensitivity analyses was carried out on key parameters including the type of subgrade soil, stabilizing agent, stabilizing agent treatment levels, and moisture conditioning. Additionally, numerical analyses was performed to …

Bio-Binder—Innovative Asphalt Technology, Amir Tabakovic

Articles

The global road network spans 16.3 million km [1], of which 5 million km is in the EU. These road networks fulfil major economic and social goals by facilitating the movement of goods and people throughout the EU, and are therefore of the utmost importance to the economic and social life of the EU [2]. National governments invest heavily in their road networks, e.g., in 2014, EUR 53.33 billion was invested in the development and maintenance of the EU road network [3]. Each year, the world produces 1.6 trillion tonnes of asphalt [4], of which 218 million tonnes is produced …

An Investigation Into The Effects Of Fly Ash On Freeze-Thaw Durability Prediction, Yancy Schrader

Graduate Theses and Dissertations

Air is purposefully entrained into concrete primarily to improve resistance to freeze-thaw deterioration while saturated with water. Air entraining admixtures (AEAs) are chemical admixtures designed to entrain air into the concrete to provide adequate resistance to the effects of freezing and thawing. One of the challenges associated with air entrainment in concrete is the interaction of an AEA with supplementary cementitious materials present in the concrete, particularly fly ash. Fly ash is a by-product of the coal fired electrical generation industry, and often contains residual unburned carbon and other components that can increase the AEA demand of a particular concrete …

Effect Of Citric Acid On Slump, Compressive Strength, And Setting Time Of Belitic Calcium Sulfoaluminate Concrete, Israel Aguilar Rosero

Graduate Theses and Dissertations

Belitic calcium sulfoaluminate (BCSA) cement has well established advantages related to fast setting time, fast strength gain, long-term strengths, shrinkage, and sustainability. Due to its fast setting and hardening, this type of cement has historically been used to repair concrete structures, highways, and runways. This work provides much needed guidance on establishing mix design criteria for BCSA cement. Guidance is also given on the effects of set retarders on strength, slump, and setting times. Citric acid and a phosphonic acid-based admixture were tested as retarders for different concrete mixtures. Three studies were performed. In the slump study five different water …

Application Of Percentage Within Limits Concepts On A Balanced Mix Design Of Asphalt Mixtures, Elvis Alexander Castillo Camarena

Graduate Theses and Dissertations

Many agencies have incorporated rutting, and more recently cracking, laboratory test requirements in the design process of asphalt mixtures. The objective of each additional specification is to produce a balance between the stability and durability of the final product. Although a performance-engineered mixture design (PEMD), denoted here as a balanced mix design (BMD), offers compelling benefits, there is concern regarding the compatibility of the BMD with current construction practices. The objective of this work is to correlate a BMD method with realistic binder content construction tolerances by applying the concepts of a percent-within-limits (PWL) approach to field QC/QA. First, Chapter …

Development Of Multi-Axial Fatigue Retrofits For Lock Gate Components, Logan Verkamp

Graduate Theses and Dissertations

Lock gates are essential infrastructure components to the United State (US) supply chain. They create large cost savings and environmental benefits when compared with traditional methods of transport (freight and rail). Because of the large quantity of goods and dependence on these shipping chains, the US economy can be drastically affected by an unexpected gate closure. Unfortunately, many lock gates within the US have reached or exceeded their designed life. Due to the intensity of cyclic loads and the environment, fatigue cracks have become a prominent issue. Developed cracks near the pintle region (a joint which the gate rotates and …

The Application Of Gray-Scale Level-Set Method In Segmentation Of Concrete Deck Delamination Using Infrared Images, Chongsheng Cheng, Zhigang Shen

Department of Construction Engineering and Management: Faculty Publications

Conventional nondestructive delamination detection of concrete pavements through thermography is often based on temperature contrasts between delaminated and sound areas. Non-uniform backgrounds caused by the environmental conditions are often challenging for contrast-based methods to robustly differentiate the delaminated areas from the sound areas. Instead of focusing on the temperature contrast, this study proposes a temperature gradient-based level set method (LSM) to detect boundaries for delamination segmentations. A modified edge indicator function is developed to represent the normalized temperature gradient of a thermal image. The experimental study was conducted to evaluate its applicability and stability for boundary detection in terms of …

Soil-Recycled Aggregate-Geopolymer Road Base/Subbase Mixtures: Steps Towards Sustainability, Mohammad Khattak, Daniel Odion

Data

Corresponding data set for Tran-SET Project No. 18GTLSU10. Abstract of the final report is stated below for reference:

"This study deals with the development of Soil-Geopolymer mixtures using flyash, alkali activator and recycled aggregates (RAG) including recycled concrete (RCA) and reclaimed asphalt (RAP) as an alternative to soil-cement for pavement base and subbase layers. Several mix constituents were varied such as flyash type and content, RCA and RAP content and ratio of sodium silicate and sodium hydroxide. Experiment design was established and mechanical and durability characteristics of Soil-RAG-Geopolymer mixtures were evaluated and then compared to the conventional soil-cement mixtures. The …

Soil-Recycled Aggregate-Geopolymer Road Base/Subbase Mixtures: Steps Towards Sustainability, Mohammad Khattak, Daniel Odion

Publications

This study deals with the development of Soil-Geopolymer mixtures using flyash, alkali activator and recycled aggregates (RAG) including recycled concrete (RCA) and reclaimed asphalt (RAP) as an alternative to soil-cement for pavement base and subbase layers. Several mix constituents were varied such as flyash type and content, RCA and RAP content and ratio of sodium silicate and sodium hydroxide. Experiment design was established and mechanical and durability characteristics of Soil-RAG-Geopolymer mixtures were evaluated and then compared to the conventional soil-cement mixtures. The results of the testing showed that for the selected Soil-RAG-Geopolymer mixtures the strength, stiffness, permanent deformation, and durability …

Mitigating Reflective Cracking Through The Use Of A Ductile Concrete Interlayer, Qian Zhang, Mohammad Khattak, Adway Das

Data

Corresponding data set for Tran-SET Project No. 18PLSU13. Abstract of the final report is stated below for reference:

"Reflective cracking is considered one of the most important issues that causes premature deterioration of composite pavements. Many types of mitigation methods have been studied in the past. However, they are either not effective in delaying the reflective cracking, or they only extend the service life by a few years. To address this critical issue and significantly extend the service life of the composite pavement, in this research, a ductile interlayer made of engineered cementitious composites (ECC) was proposed. It was hypothesized …

Development Of Geopolymer-Based Cement And Soil Stabilizers For Transportation Infrastructure, Miladin Radovic, Anand Puppala

Data

Corresponding data set for Tran-SET Project No. 18CTAM03. Abstract of the final report is stated below for reference:

"Geopolymer Cement (GPC) has drawn much attention in the recent years as an alternative to Ordinary Portland Cement (OPC) for soil stabilization, pavements, bridges and other transportation structures due to their good mechanical properties in comparison to OPC. In addition, GPC can be processed at room temperatures from aqueous solutions of waste materials (e.g. fly ash) or abundant natural sources (e.g. clay), thereby significantly reducing CO2 production associated with processing of OPC. As such, GPC proves to be a more sustainable and …

Toward Non-Corrosion And Highly Sustainable Structural Members By Using Ultra-High-Performance Materials For Transportation Infrastructure, Shih-Ho Chao, Ashish Karmacharya

Data

Corresponding data set for Tran-SET Project No. 18STUTA01. Abstract of the final report is stated below for reference:

"This research focused on investigating a highly sustainable and efficient reinforced concrete structural member for future infrastructure by utilizing emerging high-performance materials. These materials include ultra-high-performance fiber-reinforced concrete (UHP-FRC) and corrosion-resistant high-strength fiber-reinforced polymer (FRP) bars. Four reduced scale UHP-FRC specimens were tested under large displacement reversals to prove the proposed new ductile-concrete strong-reinforcement (DCSR) design concept by fully utilizing these ultra-high-performance materials. Micro steel fibers were incorporated into three specimens and ultra-high molecular weight polyethylene fibers were blended into the fourth …

Investigation Of Physical And Dynamic Properties Of High Porous Concrete, Ildar Akhmadullin

Publications

This project pursued two main objectives: (1) providing opportunities to Baton Rouge Community College (BRCC) students to develop hands-on laboratory skills and exposure to the transportation field, and (2) investigating porous concrete properties. Several BRCC student groups performed the work presented within this report; students prepared samples with different porosity and permeability according to standard specifications. The testing of the samples was performed at the Louisiana Transportation Research Center (LTRC) facility under the supervision of LTRC specialists. Findings indicate that the porosity of samples is backward proportional to the compression strength. This function is not linear but can be estimated …

Toward Non-Corrosion And Highly Sustainable Structural Members By Using Ultra-High-Performance Materials For Transportation Infrastructure, Shih-Ho Chao, Ashish Karmacharya

Publications

This research focused on investigating a highly sustainable and efficient reinforced concrete structural member for future infrastructure by utilizing emerging high-performance materials. These materials include ultra-high-performance fiber-reinforced concrete (UHP-FRC) and corrosion-resistant high-strength fiber-reinforced polymer (FRP) bars. Four reduced scale UHP-FRC specimens were tested under large displacement reversals to prove the proposed new ductile-concrete strong-reinforcement (DCSR) design concept by fully utilizing these ultra-high-performance materials. Micro steel fibers were incorporated into three specimens and ultra-high molecular weight polyethylene fibers were blended into the fourth specimen. One specimen with ASTM A1035 MMFX high-strength steel rebars, one with high-strength glass fiber reinforced polymer (GFRP) …

Development Of Geopolymer-Based Cement And Soil Stabilizers For Transportation Infrastructure, Miladin Radovic, Anand Puppala

Publications

Geopolymer Cement (GPC) has drawn much attention in the recent years as an alternative to Ordinary Portland Cement (OPC) for soil stabilization, pavements, bridges and other transportation structures due to their good mechanical properties in comparison to OPC. In addition, GPC can be processed at room temperatures from aqueous solutions of waste materials (e.g. fly ash) or abundant natural sources (e.g. clay), thereby significantly reducing CO2 production associated with processing of OPC. As such, GPC proves to be a more sustainable and environmentally friendly alternative than OPC. This research explores methods to develop GPC with desired properties and evaluate their …

Use Of Rice Husk Ash (Rha) In Flowable Fill Concrete Mix Material, Zahid Hossain, Kazi Tamzidul Islam

Data

Corresponding data set for Tran-SET Project No. 18CASU03. Abstract of the final report is stated below for reference:

"In the way of finding sustainable development, the flowable fill is a relatively new construction technology. Flowable fill is a self-compacting material, which has been developed in recent years. Flowable fill has been used for different applications such as backfilling walls, sewer trenches, bridge abutments, conduit trenches, pile excavations, and retaining walls. This study examines the potential uses of Rice Husk Ash (RHA) as a sustainable cementitious material (SCM) in the preparation of flowable fill concrete. (RHA is an agricultural by-product of …

Self-Healing Concrete Using Encapsulated Bacterial Spores In A Simulated Hot Subtropical Climate, Marwa Hassan, Jose Milla, Tyson Rupnow, Ahsennur Soysal

Data

Corresponding data set for Tran-SET Project No. 18CLSU02. Abstract of the final report is stated below for reference:

"Bacterial concrete has become one of the most promising self-healing alternatives due to its capability to seal crack widths through microbial induced calcite precipitation (MICP). In this study, two bacterial strains were embedded at varying dosages (by weight of cement) in concrete. Beam specimens were used to identify the maximum crack-sealing efficiency, while cylinder samples were used to determine their effects on the intrinsic mechanical properties, as well as its stiffness recovery over time after inducing damage. The concrete specimens were cured …

Use Of Bagasse Ash As A Concrete Additive For Road Pavement Application, Gabriel Arce, Marwa Hassan, Maria Gutierrez-Wing, Michele Barbato

Data

Corresponding data set for Tran-SET Project No. 18CLSU03. Abstract of the final report is stated below for reference:

"The objective of this study was to evaluate the use of sugarcane bagasse ash (SCBA) as a partial replacement of cement in concrete for road pavement application. The study explored the pozzolanic activity of SCBA produced from three different processing methodologies (i.e., raw SCBA, controlled SCBA and post-processed SCBA). The experimental results revealed that SCBA produced by the controlled burning of sugarcane bagasse fiber (SBF) at 650°C and grinding (C-650), presented the maximum pozzolanic activity. However, this SCBA production process was deemed …

Uhpc Shear Keys In Concrete Bridge Superstructures, Craig Newtson, Brad Weldon, Elsy Flores, Jordan Varbel, William Toledo

Data

Corresponding data set for Tran-SET Project No. 18CNMS01. Abstract of the final report is stated below for reference:

"This research investigated the use of locally produced ultra-high performance concrete (UHPC) as a grouting material to repair deteriorated shear keys. Shear keys are used in adjacent girder superstructures to produce monolithic behavior and load transfer across the structure. Shear key durability is a concern since shear key degradation can jeopardize the integrity of the structure. Transportation agencies have reported that 75% of distress in adjacent girder bridges is due to cracking and de-bonding along shear keys. Previous research has shown that …

Uhpc Shear Keys In Concrete Bridge Superstructures, Craig Newtson, Brad Weldon, Elsy Flores, Jordan Varbel, William Toledo

Publications

This research investigated the use of locally produced ultra-high performance concrete (UHPC) as a grouting material to repair deteriorated shear keys. Shear keys are used in adjacent girder superstructures to produce monolithic behavior and load transfer across the structure. Shear key durability is a concern since shear key degradation can jeopardize the integrity of the structure. Transportation agencies have reported that 75% of distress in adjacent girder bridges is due to cracking and de-bonding along shear keys. Previous research has shown that locally produced UHPC has excellent mechanical and durability properties. UHPC has also been shown to have good bonding …