Structural Materials Commons^™

Fatigue Resistant Cast Steel Railcar Couplers Produced By Wire-Arc Additive Manufacturing (Waam), Samuel Vellequette

Dissertations, Master's Theses and Master's Reports

Every year, approximately 90,000 cast steel railcar coupler knuckles are replaced preemptively to avoid fatigue failure. The coupler geometry has been in service since the early 1930s, so geometry changes are restricted to maintain compatibility with the existing fleet. Defects from the casting process, decarburization during heat treatment, and in-service exposure to corrosive environments combine to promote fatigue crack nucleation in high-stress regions of the knuckle. Wire-arc additive manufacturing (WAAM), which uses traditional welding techniques to build material to near-net shapes, was employed to deposit higher-strength materials in critical regions. By replacing the cast steel in the high-stress region of …

Experimental Investigation Of Liquid Metal Embrittlement In Hot-Dip Galvanized Structural Steel, Amelia Mcnamee

College of Graduate Studies: Theses & Dissertations

This research investigated the liquid metal embrittlement (LME) of hot-dipped galvanized structural steel. The relationship between stress and failure time was analyzed to evaluate the potential presence of a critical stress threshold beyond which LME may occur. A testing apparatus to induce axial stress was designed and assembled in-house. A36 low carbon steel was tested in this study. Different deadweight loadings were applied to the testing sample along the axial direction. The test temperature was maintained by a programmable furnace while the sample gauge section was submerged in a molten zinc bath. Failure time and total displacement of the steel …

Impact Of Quenching Intensity Conditions On Using A Finite Element Model To Investigate The Microstructure And Hardenability Of Low-Alloy Steel, J. S. Alabi, E. Heidari, M. F. Buchely, K. Chandrashekhara, S. N. Lekakh, R. J. O'Malley, V. Athavale, A. Kumar

Materials Science and Engineering Faculty Research & Creative Works

Quenching is one of the primary processes to improve mechanical properties in steels, particularly hardness. Quenching is well established for different geometries of individually treated steel components; while in-steam quenching of large diameter continuously cast steel bar has several specific features which are difficult and costly to experimentally optimize. the end-quench Jominy test has been used extensively to study the hardenability of different steel grades. Different numerical, analytical, and empirical models have been developed to simulate the Jominy process and to understand quenching of steels. However, it is not straight forward to translate experimental data from Jominy test on instream …

Impact Of Quenching Intensity Conditions On Using A Finite Element Model To Investigate The Microstructure And Hardenability Of Low-Alloy Steel, J. S. Alabi, E. Heidari, M. F. Buchely, K. Chandrashekhara, S. N. Lekakh, R. J. O'Malley, V. Athavale, A. Kumar

Materials Science and Engineering Faculty Research & Creative Works

Quenching is one of the primary processes to improve mechanical properties in steels, particularly hardness. Quenching is well established for different geometries of individually treated steel components; while in-steam quenching of large diameter continuously cast steel bar has several specific features which are difficult and costly to experimentally optimize. The end-quench Jominy test has been used extensively to study the hardenability of different steel grades. Different numerical, analytical, and empirical models have been developed to simulate the Jominy process and to understand quenching of steels. However, it is not straight forward to translate experimental data from Jominy test on instream …

Mechanical Characterization Of Functionally Graded M300 Maraging Steel Cellular Structures, Bradley Jay Sampson

Theses and Dissertations

Traditional methods for increasing the energy absorption of a structure involve using a stronger material or increasing the volume of the structure, resulting in a higher cost or additional weight. Additive manufacturing (AM) can be used to maximize the energy absorption of materials with the ability to create complex geometries such as cellular structures. Previous work has shown that the energy absorption of additively manufactured parts can be improved through functionally graded cellular structures; however, this strategy has not been applied to ultra-high strength steel materials. This work characterizes the effect of multiple functional-grading strategies (e.g. uniform, rod-graded, size-graded) on …

Implementation Of Experimental Static Recrystallization Of High Strength Steel Into Computational Simulation Of Multi-Pass Slab Hot Rolling, S. K. Dasari, S. Ganguly, A. Abutunis, K. Chandrashekhara, M. F. Buchely, S. N. Lekakh, R. J. O'Malley, T. Natarajan

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Microstructural changes and softening due to static recrystallization have a critical influence on thermo-mechanical behavior of high strength steels during industrial multi-pass hot rolling. Numerical simulation using finite element analysis (FEA) can be used to accurately predict the softening behavior during the hot rolling process. Therefore, the implementation of an experimentally defined static recrystallization model into FEA is necessary to get realistic simulation prediction. in this study, the extent of softening during static recrystallization in Si and Mn alloyed high strength steel was measured using double hit tests. a Gleeble™ thermo-mechanical simulator was used to perform the double hit tests …

Fatigue And Fracture Of Electron Beam Melting Ti-6al-4v, William A. Grell

Electronic Theses and Dissertations

For applications in the aerospace field, selection of materials for a given design requires an understanding of critical properties, like fatigue and fracture, in addition to static mechanical and physical properties. With the ongoing advancements in metallic additive manufacturing techniques and the interest in applying the process to aerospace applications, there is a clear need to fully characterize properties. Arguably, the most attractive alloy for applications in aerospace is the Ti-6Al-4V alloy. The current dissertation examines the mechanical properties of the alloy, made by the Electron Beam Melting (EBM) Powder Bed Fusion (PBF) method. As illustrated in this work, the …

A Strong And Ductile Cobalt-Free Solid-Solution Fe30ni30mn30cr10 Multi-Principal Element Alloy From Hot Rolling, Hans Pommerenke, Jiaqi Duan, Nathan Curtis, Victor Delibera, Adam Bratten, Andrew Hoffman, Mario Buchely, Ronald O'Malley, Haiming Wen

Materials Science and Engineering Faculty Research & Creative Works

Most of the face-centered cubic (FCC) multi-principal element alloys (MPEAs) developed thus far contain cobalt. for many applications, it is either required or beneficial to avoid cobalt, since cobalt has long-term activation issue (for nuclear applications), is expensive, and is considered a critical material. in addition, FCC structured solid-solution MPEAs tend to have relatively low strength. an FCC solid-solution Fe30Ni30Mn30Cr10 (at %) MPEA was fabricated via arc melting, followed by homogenization at 1100 °C for 12 h. the alloy was hot rolled at 1100 °C with a total reduction of up to 97 %. the microstructure was characterized, and mechanical …

A High-Strength Precipitation Hardened Cobalt-Free High-Entropy Alloy, Matthew Luebbe, Jiaqi Duan, Fan Zhang, Jonathan Poplawsky, Hans Pommeranke, Maalavan Arivu, Andrew Hoffman, Mario Buchely, Haiming Wen

Materials Science and Engineering Faculty Research & Creative Works

Recent studies on precipitation-hardened high-entropy alloys (HEAs) demonstrate their high strength and thermal stability, making them promising materials for high-temperature structural applications such as nuclear reactors. However, many existing HEAs contain cobalt (Co), which is unsuitable for nuclear applications because of the long-term activation issue of Co. Co is also expensive and considered a critical material for other applications. Therefore, it is desired to exclude Co from the composition. a Co-free (Fe0.3Ni0.3Mn0.3Cr0.1)88Ti4Al8 HEA was developed and studied in this work. in contrast to previous Co-free HEAs, this alloy is close to Equi atomic in its composition and promises a more …

Atomistic Simulation Studies Of Thin Film Growth And Plastic Deformation In Metals And Metal/Ceramic Nanostructures, Reza Namakian

LSU Doctoral Dissertations

Despite the significant improvements in manufacturing and synthesis processes of metals and ceramics in the past decades, there are still areas in which the procedure is still frequently more of an art or skill rather than a science. Therefore, systematic and combined experimental and computational studies are required to facilitate the development of techniques that offer thorough understanding of the events taking place during manufacturing and synthesis processes. With regard to these issues, it is paramount to address microscale characterizations and atomic scale understanding of the events during fabrication processes. One of the focuses of this study is unraveling fundamental …

Investigation Of Microstructurally Dependent Mechanical Properties Of Cold Sprayed Copper Using Correlative Microscopy, Quintin Otto

UNF Graduate Theses and Dissertations

This project employs multi-instrument materials characterization to analyze material made with the “Cold Spray” additive manufacturing process. Cold spray is an emerging additive manufacturing technique with unique benefits resulting from its low temperature adhesion process induced by plastic deformation. Metallic powder collides at high speeds creating three dimensional materials and coatings without the need for melting. Copper cold sprayed specimens were analyzed using a series of imaging techniques to characterize the microstructure at varying levels of detail and magnification. Scanning electron microscopy and electron back scattered diffraction were paired with microhardness testing to generate a correlative comparison between microstructure and …

Application Of Multi-Scale Computational Techniques To Complex Materials Systems, Mujan N. Seif

Theses and Dissertations--Chemical and Materials Engineering

The applications of computational materials science are ever-increasing, connecting fields far beyond traditional subfields in materials science. This dissertation demonstrates the broad scope of multi-scale computational techniques by investigating multiple unrelated complex material systems, namely scandate thermionic cathodes and the metallic foam component of micrometeoroid and orbital debris (MMOD) shielding. Sc-containing "scandate" cathodes have been widely reported to exhibit superior properties compared to previous thermionic cathodes; however, knowledge of their precise operating mechanism remains elusive. Here, quantum mechanical calculations were utilized to map the phase space of stable, highly-faceted and chemically-complex W nanoparticles, accounting for both finite temperature and chemical …

Structural Risk-Based Underwater Inspection (Rbui) As A Cost Reduction Of Field’S End Of Production Life, Ivan Fitrian Putra, Johny Wahyuadi Soedarsono, Mirza Mahendra, Yuki Haidir, Faisal Dwiyana Purnawarman, Iwan Sukirna, Widi Hernowo

Journal of Materials Exploration and Findings

Mubadala Petroleum operates offshore platforms in a southern Makassar Straits that needs to be periodically inspected. The cost for the inspection is massive due to the high cost of mobilization and demobilization of vessels including crew and equipment. In response of a new approach to reduce cost, a Risk-Based Underwater Inspection (RBUI) methodology is developed. This RBUI purpose is to reduce the inspection interval of the offshore platform, from every 2 years to a longer period^[1]. There are existing RBUI methodologies, which are already developed and implemented in other companies^[5]. Purpose of this paper is to …

Experimental Evidence That Shear Bands In Metallic Glasses Nucleate Like Cracks, Alan A. Long, Wendelin Wright, Xiaojun Gu, Anna Thackray, Mayisha Nakib, Jonathan T. Uhl, Karin A. Dahmen

Faculty Journal Articles

Highly time-resolved mechanical measurements, modeling, and simulations show that large shear bands in bulk metallic glasses nucleate in a manner similar to cracks. When small slips reach a nucleation size, the dynamics changes and the shear band rapidly grows to span the entire sample. Smaller nucleation sizes imply lower ductility. Ductility can be increased by increasing the nucleation size relative to the maximum (“cutoff”) shear band size at the upper edge of the power law scaling range of their size distribution. This can be achieved in three ways: (1) by increasing the nucleation size beyond this cutoff size of the …

Characterization Of Hydrogen Embrittlement Sensitivity In High Hardness Steels, David Ahlen Salley

Theses and Dissertations

High hardness steels can be affected by delayed brittle cracking often attributed to hydrogen embrittlement. Improved resistance to hydrogen embrittlement would be beneficial to many industries including military, automotive, and high-rise construction. While other prevention methods include coating, trapping, and barriers, design efforts in this study were focused on improving intrinsic properties to be more resistant to hydrogen embrittlement. Four alloys targeting 477 – 534 HB were designed and produced in-house and compared against a commercial grade 500 HB alloy. Charpy V-notch (CVN) impact toughness and tensile specimens were made according to ASTM E23 and ASTM E8 to characterize mechanical …

Austenitic, Duplex, And Lean Duplex Stainless Steel Critical Pitting Temperature In Simulated Concrete Environment, Bobby Giebel

Williams Honors College, Honors Research Projects

In this work, the critical pitting temperature (CPT) will be observed for a selection of austenitic (316LN and 24100) and duplex (2205), and lean duplex (2304, 2001) stainless steels in simulated concrete pore solution. To study the influence of temperature on the pitting stability of the stainless steels, three temperatures were tested: 25oC, 45oC, and 65oC for cyclic potentiodynamic polarization (CPP) and electrochemical impedance spectroscopy (EIS). Electrochemical properties of the interfaces we studied via EIS analysis. Kinetics were studied via CPP testing. To reveal the critical pitting temperature of the stainless steels, cyclic thermammetry was used. Characterization of the pits …

Induction Brazing, Austin Squire, Scott Compton, Logan Hathaway, Michael Fleming

Williams Honors College, Honors Research Projects

Our team would like to research and explore ways of designing a portable device that uses induction heating/brazing to connect two exhaust pipes together.

Method For Reducing Warping Stresses In Torsionally Loaded I-Section Members Using Cfrp Plates, Mamadou Konate, Zia Razzaq

Civil & Environmental Engineering Faculty Publications

This paper presents a method for reducing warping normal stresses in torsionally loaded I-section members by utilizing carbon fiber-reinforced polymer (CFRP) plates. The CFRP plates are bonded to the outer surfaces of the flanges with a view to reducing warping normal stresses. The maximum warping normal stress in the flanges of a steel I-shaped member without the CFRP plates is compared to those obtained with the CFRP plates having various thicknesses. It has been found that the use of CFRP plates bonded to both flanges of the I-section result in a substantial reduction of the warping stresses. For the study …

Derivation, Exploration And Evaluation Of Non-Equiatomic High Entropy Alloys, Artashes Ter-Isahakyan

Theses and Dissertations--Chemical and Materials Engineering

High-entropy alloys (HEAs) are a class of multicomponent alloys based on an innovative alloying strategy that employs multi-principle elements in relatively high concentrations. Commonly defined as alloys that contain at least five principal elements, each with a concentration between 5 and 35 at %. The term entropy refers to the excess configurational entropy associated with HEAs, which is thought to facilitate the formation of solid solutions. The design strategy results in vast compositional space for exploration and innovative potential triggering a renaissance in physical metallurgy. These alloys may have favorable properties compared to conventional dilute solid solutions, but their preeminent …

Minimizing Cr-Evaporation From Balance Of Plant Components By Utilizing Cost-Effective Alumina-Forming Austenitic Steels, Lingfeng Zhou

Graduate Theses, Dissertations, and Problem Reports (ETD)

A solid oxide fuel cell (SOFC) is a clean and efficient energy conversion device. The development of intermediate-temperature SOFCs has made it preferable to use metallic interconnects (MICs) to greatly reduce the cost and significantly increase the efficiency compared to ceramic interconnect materials. However, gaseous chromium species will evaporate from the chromium-containing layer formed on the surface of commonly used MICs and balance of plant (BoP) components. Volatile chromium species have been shown to form solid deposits which poison the cathodes of SOFCs, causing drastic cell performance degradation and thereby limiting commercialization. In order to alleviate the Cr poisoning and …

Review: Factors Affecting Composite Laminates Against Lightning Strikes, Aaryan Manoj Nair

Publications and Research

Lightning strike protection (LSP) have recently been a newly developing field particularly with the emergence of graphene thin film integration into carbon fiber composite structures. This technology has a widespread application in airplanes, wind turbines, and other instruments which are susceptible to frequent lightning strikes. Electrical discharge of the instrument in a safe manner is vital for the safety of the passengers (in the case of flights) as well as the integrity of the aircraft structures because of their specific mechanical and structural properties, which are essential for their functioning. The purpose of the study is to fabricate graphene thin …

Strengthening Of 7175 Aluminum Alloy Through Multi-Step Aging Process, Colin E. Masterson, Ryland W. Jolliffe

Materials Engineering

7175 is a heat-treatable aluminum alloy commonly used in aerospace forgings. This alloy is aged with a multi-step heat treatment. This treatment must balance strength with stress corrosion cracking resistance through a degree of overaging. The team was tasked by Weber Metals to increase the strength of this treatment without sacrificing stress corrosion cracking resistance. Both two-step and retrogression and reaging treatments were tested in experiments to find a heat treatment that could increase the yield and tensile strength by 1-2 ksi while maintaining a minimum electrochemical conductivity equivalence of 38% relative to copper. Two-step aging is the more conventional …

Study Of Laser Based Additive Manufacturing For Titanium And Copper Alloys, Congyuan Zeng

LSU Doctoral Dissertations

Material processing by laser is increasingly applied in industrial applications for its outstanding characteristics, such as localized heating, high efficiency, and high manufacturing precision. In this study, two kinds of laser material processing strategies were investigated, namely laser surface engineering and laser-powder-bed fusion additive manufacturing, with pure titanium and copper alloys as target materials, respectively.

For laser surface engineering related studies, the work includes the investigation of the dynamic interactions between titanium and pure nitrogen or ambient air under transient laser processing conditions. Thanks to the in-situ synchrotron X-ray diffraction tests, the high-temperature reaction steps between titanium and pure nitrogen/ambient …

Atomistic Monte Carlo Simulation Study Of Phase Transitions In Metal Alloys, Xiaoxu Guo

Dissertations, Master's Theses and Master's Reports

The atomic-scale Monte Carlo simulation study focuses on the intrinsic behaviors of a defect-free crystal that undergoes a cubic-to-tetragonal martensitic transformation. The quasi-spin variable associated with the lattice sites characterizes the local unit cells of the orientation variants of the ground-state martensite phase, which interact with each other through long-range elastic interactions. It is shown that the diffuse scattering in the premartensitic austenite state results from the spatial correlation of the atomic-scale heterogeneous lattice displacements and manifests the displacement short-range ordering. The effects of temperature, elastic anisotropy, and shear modulus softening on the diffuse scattering and displacement short-range ordering are …

Application Of Laser Assisted Ultrasonic Nanocrystal Surface Modification On Aluminum And 3d Printed Titanium, Eman Hassan, Thomas Crouse

Williams Honors College, Honors Research Projects

A novel surface treatment, laser assisted ultrasonic nanocrystal surface modification (LA-UNSM), has proved effective in increasing surface hardness, and fatigue life. The objective of this research is to determine the effectiveness of this process on components created with additive manufacturing. To accomplish this, we investigated the effectiveness of LA-UNSM treatment on aluminum, a common 3d printed metal, and the effectiveness of LA-UNSM processing on 3d printed titanium. We first conducted our own literature review to assess the practicality of using this same treatment on aluminum. We then treated traditionally manufactured aluminum at varying levels of laser intensity to determine if …

A Modified Johnson-Cook Model Incorporating The Effect Of Grain Size On Flow Stress, S. Ganguly, Mario F. Buchely, K. Chandrashekhara, Semen Naumovich Lekakh, Ronald J. O'Malley

Materials Science and Engineering Faculty Research & Creative Works

The mechanical properties of steel are influenced by grain size, which can change through mechanisms such as nucleation and growth at elevated temperatures. However, the classic Johnson-Cook model that is widely used in hot deformation simulations does not consider the effect of grain size on flow stress. In this study, the Johnson-Cook model was modified to incorporate the effects of austenite grain size on flow stress. A finite element model was employed to characterize the effects of grain size on the flow stress for different steel grades over a range of temperatures (900⁰ to 1300⁰). Simulation results show good agreement …

Spherical Cavity Expansion Approach For The Study Of Rigid-Penetrator’S Impact Problems, Mario Buchely, Alejandro Marañon

Materials Science and Engineering Faculty Research & Creative Works

In recent years, Spherical Cavity Expansion (SCE) theory has been extensively utilized to model dynamic deformation processes related to indentation and penetration problems in many fields. In this review, the SCE theory is introduced by explaining the different mathematical features of this theory, its solution, and a potential application to model the penetration of a rigid penetrator into a deformable target. First, a chronologically literature review of the most common models used to study this kind of penetration problems is introduced, focusing on the SCE theory. Then, the engineering model of penetration is presented using the SCE approach. The model …

Investigation On The Mechanical Properties And Microstructure Analysis Of Micro-Resistance Spot Welding Between Stainless Steel 316l And Tl-6al-4v, Mohd Mansor Muhammad Safwan

Student Works (2020-2029)

In this study, ASS 316L and Ti-6Al-4V were welded together by micro-resistance spot welding (μRSW) at different combinations of welding parameters using specifically design electrode geometry in order to acquire the optimal combination of welding parameters. The welded joint were subjected to tensile shear strength test to determine the influence of welding current, welding time, welding force and different design of elctrode tip on the mechanical properties and the strength of the welded joint. The experiment was conducted by using full factorial design of experiment (DoE) with L27 orthogonal array and utilizing the analysis of variance (ANOVA) to obtain the …

Influence Of Rapid Solidification And Wrought Processing On Precipitation Strengthening And Deformation Mechanisms In Al-Sc-Zr Alloys, Yang Yang

Dissertations, Master's Theses and Master's Reports

Al-Sc-Zr alloys have drawn increasing attention in the last several decades due to their strengthening and coarsening resistance. In this study, solute concentrations of Sc and Zr were increased beyond their equilibrium solubilities without primary precipitate formation using melt-spinning. The melt-spun ribbon was metallurgically bonded into bulk shape using extrusion. With the proper aging treatment, the mechanical properties of the supersaturated melt-spun ribbon and extruded rod were found to be significantly higher than a baseline dilute alloy. Increased mechanical properties include microhardness, tensile strength at ambient-temperature, and compressive strength and threshold stress at and elevated-temperature. These increases were related to …

Jominy Hardenability Tester With In-Situ Heating, Luke Allen

Williams Honors College, Honors Research Projects

This project centers on building a Jominy Hardenability tester with In-Situ heating for the manufacturing lab at the University of Akron. A new process and setup will be designed using engineering concepts in order to make the testing more efficient and safer for the teaching and testing of metal hardness. The current Jominy testing setup has efficiency issues within the transfer of specimen from induction heater to testing rig. Our design will simplify the design by creating a test rig that removes the traveling aspect of the specimen which will limit the amount of premature cooling done and will be …