Semiconductor and Optical Materials Commons^™

Carrier Transport Engineering In Wide Bandgap Semiconductors For Photonic And Memory Device Applications, Ravi Teja Velpula

Dissertations

Wide bandgap (WBG) semiconductors play a crucial role in the current solid-state lighting technology. The AlGaN compound semiconductor is widely used for ultraviolet (UV) light-emitting diodes (LEDs), however, the efficiency of these LEDs is largely in a single-digit percentage range due to several factors. Until recently, AlInN alloy has been relatively unexplored, though it holds potential for light-emitters operating in the visible and UV regions. In this dissertation, the first axial AlInN core-shell nanowire UV LEDs operating in the UV-A and UV-B regions with an internal quantum efficiency (IQE) of 52% are demonstrated. Moreover, the light extraction efficiency of this …

Void-Semiconductor Gaas Photonic Crystal Surface-Emitting Lasers By Epitaxial Regrowth And Single-Epitaxy Methods, Kevin James Reilly

Nanoscience and Microsystems ETDs

Monolithic semiconductor lasers including edge-emitting lasers (EELs) and vertical-cavity surface-emitting lasers (VCSELs) fail to realize simultaneous achievement of both high-power high-quality beams due to intrinsic limitations of their resonant cavity. Photonic crystal surface emitting lasers (PCSELs) address these structural limitations through employment of a two-dimensional photonic crystal (PC) cavity that creates feedback at a single wavelength for laterally scalable devices. This function of the PC allows PCSELs to power scale with area while maintaining single-mode emission required for diffraction-limited beams. In this way, PCSELs fulfill an industry demand for high-power high-quality lasing from a single chip.

Early PCSELs were fabricated …

Design, Fabrication, And Characterization Of Conjugated Polymeric Electrochemical Memristors As Neuromorphic/Integrated Circuits, Benjamin Grant

All Dissertations

Organic materials are promising candidates for future electronic devices compared to the complementing inorganic materials due to their ease of processability, use, and disposal, low cost of fabrication, energy efficiency, and flexible nature toward implementation as flexible and non-conformal devices.With that in mind, electrochemical materials have been widely demonstrated with commercial use as sensors, displays, and a variety of other electronic devices. As Moore's law predicts the increase in the density of transistors on a chip, the requirement to create either smaller transistors or the replacement of the transistor device entirely is apparent. Memory resistors, coined ``memristor", are variable resistive …

Seeing The Big Picture: System Architecture Trends In Endoscopy And Led-Based Hyperspectral Subsystem Intergration, Craig M. Browning

Graduate Theses and Dissertations (2019 - present)

Early-stage colorectal lesions remain difficult to detect. Early development of neoplasia tends to be small (less than 10 mm) and flat and difficult to distinguish from surrounding mucosa. Additionally, optical diagnosis of neoplasia as benign or malignant is problematic. Low rates of detection of these lesions allow for continued growth in the colorectum and increased risk of cancer formation. Therefore, it is crucial to detect neoplasia and other non-neoplastic lesions to determine risk and guide future treatment. Technology for detection needs to enhance contrast of subtle tissue differences in the colorectum and track multiple biomarkers simultaneously. This work implements one …

Investigation Of Gaas Double Heterostructures For Photonic Heat Engines, Nathan Giannini-Hutchin

Optical Science and Engineering ETDs

The creation of a laser cooled semiconductor device has been a long sought achievement. GaAs-based devices have emerged as a promising candidate for the realization of this goal. Efforts to improve the efficiency of such devices have enabled the material to exhibit external quantum efficiencies (EQE, a measure of the probability that an excitation leads to the emission of a photon) of 99.5\%. Despite this impressive feat, a laser coolable device remains elusive.

To investigate the obstacles to such a device, the material characteristics of GaAs-based double heterostructures (DHS) are theoretically and experimentally examined. Through this study, a GaAs $\vert$ …

Transition-Metal Ions In Β-Ga2O3 Crystals: Identification Of Ni Acceptors, Timothy D. Gustafson, Nancy C. Giles, Brian C. Holloway, J. Jesenovec, B. L. Dutton, M. D. Mccluskey, Larry E. Halliburton

Faculty Publications

Excerpt: Transition-metal ions (Ni, Cu, and Zn) in β-Ga₂O₃ crystals form deep acceptor levels in the lower half of the bandgap. In the present study, we characterize the Ni acceptors in a Czochralski-grown crystal and find that their (0/−) level is approximately 1.40 eV above the maximum of the valence band.

Material Characterization And Comparison Of Sol-Gel Deposited And Rf Magnetron Deposited Lead Zirconate Titanate Thin Films, Katherine Lynne Miles

Mechanical Engineering ETDs

Lead zirconate titanate (PZT) has been a material of interest for sensor, actuator, and transducer applications in microelectromechanical systems (MEMS). This is due to their favorable piezoelectric, pyroelectric and ferroelectric properties. While various methods are available to deposit PZT thin films, radio frequency (RF) magnetron sputtering was selected to provide high quality PZT films with the added capability of batch processing. These sputter deposited PZT films were characterized to determine their internal film stress, Young’s modulus, composition, and structure. After characterization, the sputtered PZT samples were poled using corona poling and direct poling methods. As a means of comparison, commercially …

Sculpting Charge In Graphene Through Patterned Strain, Dylan J. Balter, Jenna Smith

The Journal of Purdue Undergraduate Research

No abstract provided.

Optimizing Switching Of Non-Linear Properties With Hyperbolic Metamaterials, James A. Ethridge, John G. Jones, Manuel R. Ferdinandus, Michael J. Havrilla, Michael A. Marciniak

Faculty Publications

Hyperbolic metamaterials have been demonstrated to have special potential in their linear response, but the extent of their non-linear response has not been extensively modeled or measured. In this work, novel non-linear behavior of an ITO/SiO₂ layered hyperbolic metamaterial is modeled and experimentally confirmed, specifically a change in the sign of the non-linear absorption with intensity. This behavior is tunable and can be achieved with a simple one-dimensional layered design. Fabrication was performed with physical vapor deposition, and measurements were conducted using the Z-scan technique. Potential applications include tunable optical switches, optical limiters, and tunable components of laser sources.

Oxygen Vacancies In Lib3O5 Crystals And Their Role In Nonlinear Absorption, Brian C. Holloway, Christopher A. Lenyk, Timothy D. Gustafson, Nancy C. Giles

Faculty Publications

LiB₃O₅ (LBO) crystals are used to generate the second, third, and fourth harmonics of near-infrared solid-state lasers. At high power levels, the material’s performance is adversely affected by nonlinear absorption. We show that as-grown crystals contain oxygen and lithium vacancies. Transient absorption bands are formed when these intrinsic defects serve as traps for “free” electrons and holes created by x rays or by three- and four-photon absorption processes. Trapped electrons introduce a band near 300 nm and trapped holes produce bands in the 500-600 nm region. Electron paramagnetic resonance (EPR) is used to identify and characterize the …

Fabrication And Non-Covalent Functionalization And Characterization Of Graphene-Based Devices On Novel Substrate Cadmium Trithiophosphate (Iv) — Cdps, Abayomi Omotola Omolewu

Graduate Theses and Dissertations

With graphene at the center of several application areas such as sensing, circuits, high-frequency devices for communication systems, etc., it is crucial to understand how the intrinsic properties of devices made from graphene and other materials like platinum and palladium nanoparticles affect the performance of such devices for the specific application area. Many graphene-based devices for different application areas have focused mainly on the material composition of the graphene-based devices and how it affects performance parameters for the specific application. However, it would be insightful to understand how the intrinsic electrical properties of the graphene devices for different applications affect …

Sub-Bandgap Photon-Assisted Electron Trapping And Detrapping In Algan/Gan Heterostructure Field-Effect Transistors, Andrew Gunn

All Theses

We have investigated photon-assisted trapping and detrapping of electrons injected from the gate under negative bias in a heterostructure field-effect transistor (HFET). The electron injection rate from the gate was found to be dramatically affected by sub-bandgap laser illumination. The trapped electrons reduced the two-dimensional electron gas (2DEG) density at the AlGaN/GaN heterointerface but could also be emitted from their trap states by sub-bandgap photons, leading to a recovery of 2DEG density. The trapping and detrapping dynamics were found to be strongly dependent on the wavelength and focal position of the laser, as well as the gate bias stress time …

Xps And Ipe Determination Of Band Offsets Of Germanium Based Materials, Justin Michael Rudie

Graduate Theses and Dissertations

Germanium tin and silicon germanium tin are group IV semiconductor alloys that have gained significant interest in recent years for their potential use in optoelectrical devices. While silicon and germanium are indirect bandgap materials on their own, alloying them with tin in sufficient quantities leads to a transition to direct bandgap alloys. Direct gap performance opens the door for efficient light emitting and detecting devices fabricated entirely on group IV materials that are compatible with the industry standard CMOS manufacturing techniques. Germanium tin and silicon germanium tin have bandgaps that respond to light in the mid to near infrared spectrum …

Etching Process Development For Sic Cmos, Weston Reed Renfrow

Graduate Theses and Dissertations

Silicon Carbide (SiC) is an exciting material that is growing in popularity for having qualities that make it a helpful semiconductor in extreme environments where silicon devices fail. The development of a SiC CMOS is in its infancy. There are many improvements that need to be made to develop this technology further. Photolithography is the most significant bottleneck in the etching process; it was studied and improved upon. Etching SiC can be a challenge with its reinforced crystal structure. Chlorine-based inductively coupled plasma (ICP) etching of intrinsic SiC and doped SiC, SiO2, and Silicon has been studied. A baseline chlorine …

Study Of Single-Photon Wave-Packets With Atomically Thin Nonlinear Mirrors, Christopher Klenke

Graduate Theses and Dissertations

A novel controlled phase gate for photonic quantum computing is proposed by exploiting the powerful nonlinear optical responses of atomically thin transition metal dichalcogenides (TMDs) and it is shown that such a gate could elicit a π-rad phase shift in the outgoing electric field only in the case of two incident photons and no other cases. Firstly, the motivation for such a gate is developed and then the implementation of monolayer TMDs is presented as a solution to previous realization challenges. The single-mode case of incident photons upon a TMD is derived and is then used to constrain the more …

Subwavelength Engineering Of Silicon Photonic Waveguides, Farhan Bin Tarik

All Dissertations

The dissertation demonstrates subwavelength engineering of silicon photonic waveguides in the form of two different structures or avenues: (i) a novel ultra-low mode area v-groove waveguide to enhance light-matter interaction; and (ii) a nanoscale sidewall crystalline grating performed as physical unclonable function to achieve hardware and information security. With the advancement of modern technology and modern supply chain throughout the globe, silicon photonics is set to lead the global semiconductor foundries, thanks to its abundance in nature and a mature and well-established industry. Since, the silicon waveguide is the heart of silicon photonics, it can be considered as the core …

Study Of Thin Gan/Ingan/Gan Double Graded Structures For Future Photovoltaic Application, Mirsaeid Sarollahi

Graduate Theses and Dissertations

Indium gallium nitride (In_x Ga_(1-x) N) materials have displayed great potential for photovoltaic and optoelectronic devices due to their optical and electrical properties. Properties such as direct bandgap, strong bandgap absorption, thermal stability and high radiation resistance qualify them as great materials for photovoltaic devices. The tunable bandgap which absorbs the whole solar spectrum is the most significant feature which became attractive for scientists. The bandgap for these materials varies from 0.7 eV for InN to 3.4 eV for GaN covering from infrared to ultraviolet. In_x Ga_(1-x) N wurtzite crystal is grown on GaN buffer layer by Molecular Beam Epitaxy …

Optimization Of Pulse Plating Additives And Plating Parameters For High Aspect Ratio Through Holes, Kai Yang, Ji-Da Chen, Shi-Jin Chen, Wei-Lian Xu, Mao-Gui Guo, Jin-Chao Liao, Zeng-Kun Wu

Journal of Electrochemistry

As an important component in electronic products, printed circuit board (PCB) plays a supporting and interconnecting role for the electronic components in it. With the development of communication technology, electronic products are developing in the direction of “thin, light and small”, and high density interconnection (HDI) comes into being. Due to the high-density interconnection characteristics of HDI boards, the thickness of the board is increasing. At the same time, in order to reserve space for the laying of fine lines on the subsequent board surface, the diameter of the through holes on the board is also decreasing, so the depth-diameter …

Research Progresses Of Cobalt Interconnect And Superfilling By Electroplating In Chips, Li-Jun Wei, Zi-Han Zhou, Yun-Wen Wu, Ming Li, Su Wang

Journal of Electrochemistry

Copper interconnect using dual damascene technology has always been the main means for metallization in the back end of line process. However, with the size effect becoming more and more obvious due to feature size reduction, copper interconnect can no longer meet the demand for high circuit speed in Post-Moore era. Following copper interconnection, cobalt interconnection in chips attracts much attention as an interconnect technology by the next generation, which has been introduced in 7 nm node of integrated circuit manufacturing and below. The electron mean free path of cobalt (~10 nm) is much shorter than copper’s (39 nm), thus …

Development Status Of Copper Electroplating Filling Technology In Through Glass Via For 3d Interconnections, Zhi-Jing Ji, Hui-Qin Ling, Pei-Lin Wu, Rui-Yi Yu, Da-Quan Yu, Ming Li

Journal of Electrochemistry

With the slow development of Moore's Law, the high density and miniaturization of microelectronic devices put forward higher requirements for advanced packaging technology. As a key technology in 2.5D/3D packaging, interposer technology has been extensively studied. According to different interposer materials, it is mainly divided into organic interposer, silicon interposer and glass interposer. Compared with the through silicon via (TSV) interconnection, the through glass via (TGV) interposer has received extensive attention in the 2.5D/3D advanced packaging field for its advantages of excellent high-frequency electrical characteristics, simple process, low cost, and adjustable coefficient of thermal expansion (CTE). However, the thermal conductivity …

Noncontact Liquid Crystalline Broadband Optoacoustic Sensors, Hengky Chandrahalim, Michael T. Dela Cruz

AFIT Patents

An optoacoustic sensor includes a liquid crystal (LC) cell formed between top and bottom plates of transparent material. A transverse grating formed across the LC cell that forms an optical transmission bandgap. A CL is aligned to form a spring-like, tunable Bragg grating that is naturally responsive to external agitations providing a spectral transition regime, or edge, in the optical transmission bandgap of the transverse grating that respond to broadband acoustic waves. The optoacoustic sensor includes a narrowband light source that is oriented to transmit light through the top plate, the LC cell, and the bottom plate. The optoacoustic sensor …

Photon Attenuation Layer Silicon-Based X-Ray Detector: Quantum Efficiency Investigation And Algorithmic Processing Of Individual Detection Events, Kevin Larkin

ENGS 88 Honors Thesis (AB Students)

State-of-the-art X-ray detectors either use silicon direct detection—which is inefficient, as silicon is mostly transparent to high-energy X-rays—or rely on expensive scintillators to first down-convert X-ray photons to lower energies. Dr. Eldred Lee of Dartmouth College recently completed doctoral research that suggested the promise of a novel alternative: silicon-based X-ray detectors that utilize photon attenuation layers rather than scintillators. While Dr. Lee’s work is certainly rigorous and meritorious, background noise controls were rendered less effective by circumstances. The work presented in this thesis succeeded in implementing much better background noise controls for a series of new tests to compare the …

Processing And Characterization Of Silicon Nitride For Rapid And Low-Level Detection Of Water Pathogens, Arielle H. Buchanan, Logan A. Chai

Materials Engineering

Water sanitation is a serious issue affecting the lives of many, and methods for assessing water cleanliness have been a major research interest for decades. Rapid and accurate water pathogen detection methods that can be performed in field applications have been a growing research focus, especially in low-income countries most affected by poor water quality. Silicon nitride was explored as a material for colorimetric water-pathogen sensing due to the large body of knowledge around its processing, and its isoelectric point. A bioassay of chlorophenol red-β-Dgalactopyranoside (CPRG) and β-galactosidase (β-gal) enzymes with Escherichia coli (E. coli) bacteria was used to examine …

Identification And Characterization Of Point Defects In Nonlinear Optical Crystals: Barium Gallium Selenide And Lithium Triborate, Brian C. Holloway

Theses and Dissertations

Increased interest in developing new nonlinear optical materials has led to 3rd generation materials, such as BaGa4Se₇ and LiB₃O₅. These two nonlinear optical crystals have the potential to enable development of tunable lasers operating across the mid-wave infrared and the ultraviolet regions, respectively. Coherent light sources are used in the development of enhanced technologies with commercial and defense-based applications such as: health and environmental monitoring devices, next-generation infrared countermeasures, and ballistic missile booster exhaust plume characterization. The performance of optical materials in high-powered military applications is largely limited by the presence of defects. These defects …

Model-Based Design Of An Optimal Lqg Regulator For A Piezoelectric Actuated Smart Structure Using A High-Precision Laser Interferometry Measurement System, Grant P. Gallagher

Master's Theses

Smart structure control systems commonly use piezoceramic sensors or accelerometers as vibration measurement devices. These measurement devices often produce noisy and/or low-precision signals, which makes it difficult to measure small-amplitude vibrations. Laser interferometry devices pose as an alternative high-precision position measurement method, capable of nanometer-scale resolution. The aim of this research is to utilize a model-based design approach to develop and implement a real-time Linear Quadratic Gaussian (LQG) regulator for a piezoelectric actuated smart structure using a high-precision laser interferometry measurement system to suppress the excitation of vibratory modes.

The analytical model of the smart structure is derived using the …

Spinel Transition Metal Oxide Nanoparticle-Pigmented Solar Selective Coatings With High Thermal Efficiency And High-Temperature Thermal Stability In Air, Can Xu

Dartmouth College Ph.D Dissertations

This thesis explores spinel-structure transition metal oxide nanoparticle pigmented solar selective coatings with high thermal efficiency (>90%) and high-temperature (~750 ºC) thermodynamic stability via cost-effective and facile fabrication methods. Compared to the preliminary work, we reduce the emittance loss by selecting silicones with a lower emittance loss as the matrix. We further move from purchasing simple commercial oxide nanoparticles to systematically designing and synthesizing spinel-structure based three-transition-metal-incorporated oxide nanoparticles for a better optical response of nanoparticle pigmented coatings. Nanoparticles of three systems are studied, including Ni-Mn-Fe oxide, Cu-Mn-Fe oxide, and Cu-Mn-Cr oxide systems. Among, Cu-Mn-Cr oxide nanoparticle pigmented silicone …

A Circular Economy Approach To Improve E-Waste Recycling In California: Economic Potential And Policy Options, Kripa Shah

Master's Projects and Capstones

The higher consumption rates of electronic devices along with their short life cycles and few repair options poses a huge challenge for E-waste industries to manage them effectively. E-waste comprises of hazardous materials and toxic constituents that can affect the environment and public health through improper disposal. However, they also contain few valuable materials that, if recovered, can reduce the dependence on virgin raw materials. Circular economy has the potential to utilize these valuable materials and gain environment and socio-economic benefits. The research explains how the adoption of a circular economy approach can help improve the E-waste recycling in California …

Monolithically Integrated Microscale Pressure Sensor On An Optical Fiber Tip, Jeremiah C. Williams, Hengky Chandrahalim

AFIT Patents

A passive microscopic Fabry-Pérot Interferometer (FPI) pressure sensor includes an optical fiber and a three-dimensional microscopic optical enclosure. The three-dimensional microscopic optical enclosure includes tubular side walls having lateral pleated corrugations and attached to a cleaved tip of the optical fiber to receive a light signal. An optically reflecting end wall is distally engaged to the tubular side walls to enclose a trapped quantity of gas that longitudinally positions the optically reflecting end wall in relation to ambient air pressure, changing a distance traveled by a light signal reflected back through the optical fiber.

Hinged Temperature-Immune Self-Referencing Fabry–Pérot Cavity Sensors, Jeremiah C. Williams, Hengky Chandrahalim

AFIT Patents

A passive microscopic Fabry-Pérot Interferometer (FPI) sensor includes a three-dimensional microscopic optical structure formed on a cleaved tip of the optical fighter using a two-photon polymerization process on a photosensitive polymer by a three-dimensional micromachining device. The three-dimensional microscopic optical structure having a hinged optical layer pivotally connected to a distal portion of a suspended structure. A reflective layer is deposited on a mirror surface of the hinged optical layer while in an open position. The hinged optical layer is subsequently positioned in the closed position to align the mirror surface to at least partially reflect a light signal back …

Near-Earth Ion Irradiation Effects On Functional Ceramic Materials: A Combined Experimental-Monte Carlo Approach, William J. Sands

All Theses

The near-Earth space radiation environment is a complex system that creates a harmful environment for materials to operate in. Motivated by the search for using optical defects as an indicator of radiation damage, five single-crystal functional ceramic materials were selected to undergo ion irradiation at conditions found in the near-Earth space environment. Due to the complex nature of ion irradiation effects in ceramic materials, a host of calculations and experimental characterization methods were used. Calculations using the 2013 SRIM code were used to evaluate the ion projected range and the type and number of defects (vacancies) created by ion irradiation. …