Semiconductor and Optical Materials Commons^™

Fabrication Of Smooth Sac305 Thin Film Via Magnetron Sputtering, M. Ojha, A. A. Elmustafa

Mechanical & Aerospace Engineering Faculty Publications

SAC305 (96.5 wt% Sn, 3 wt% Ag, 0.5 wt%Cu) solder is increasingly becoming popular due to its reliability good characteristics and performance in addition to the environmental concerns and regulations that restrict the use of lead in nano/microelectronic products. In nano/microelectronics, manufacturing smooth solder coatings free of defects such as voids and cracks, which can compromise joint reliability is crucial. Magnetron sputtering offers a high degree of control over film thickness and composition, resulting in films with excellent uniformity and adhesion. Despite these advantages, fabricating continuous and robust SAC305 films using magnetron sputtering remains a difficult task with limited research …

Numerical Calculation Of Losses Of Trapped Vortices Under Strong Rf Meissner Current And Dc Superheating Field In Type Ii Superconductors, Walive Pathiranage Manula Randhika Pathirana

Physics Theses & Dissertations

Research on the vortex dynamics and enhancing of superheating field in superconductors has attracted much attention in accelerator physics community to develop next-generation high-performance accelerator cavities. However, the extreme dynamics of curvilinear elastic vortices driven by very strong currents close to the depairing limit or superheating field of a superconductor with a nanostructured surface has not been well understood. We calculated the superheating field H_sh and critical momentum kc characterizing the wavelength of the instability λ_m of the Meissner state to flux penetration by solving numerically the Ginzburg-Landau equations. A bulk superconductor, superconductor with the inhomogeneous surface disorder …

Plasma Processing Of Superconducting Radio Frequency Cavities, Janardan Upadhyay

Physics Theses & Dissertations

The development of plasma processing technology of superconducting radio frequency (SRF) cavities not only provides a chemical free and less expensive processing method, but also opens up the possibility for controlled modification of the inner surfaces of the cavity for better superconducting properties. The research was focused on the transition of plasma etching from two dimensional flat surfaces to inner surfaces of three dimensional (3D) structures. The results could be applicable to a variety of inner surfaces of 3D structures other than SRF cavities. Understanding the Ar/Cl₂ plasma etching mechanism is crucial for achieving the desired modification of Nb …

Uv Light-Induced Aggregation Of Titania Submicron Particles, Can Zhou, Yashar Bashirzadeh, Timothy A. Bernadowsky Jr., Xiaoyu Zhang

Mechanical & Aerospace Engineering Faculty Publications

In this study, aggregation of TiO₂ (rutile and anatase) submicron particles in deionized (DI) water under ultra-violet (UV) light irradiation was investigated. While no aggregation was observed in the dark, rutile and anatase submicron particles started aggregating upon application of UV light and ceased aggregation in about 2 and 8.4 h, respectively. It has been demonstrated that UV light directly mitigated the particle mobility of TiO₂, resulting in a neutralization effect of the Zeta potential. It was also observed that rutile particles aggregated much faster than anatase particles under UV radiation, indicating that the Zeta potential of …

Polarization Of Bi2te3 Thin Film In A Floating-Gate Capacitor Structure, Hui Yuan, Kai Zhang, Haitao Li, Hao Zhu, John E. Bonevich, Helmut Baumgart, Curt A. Richter, Qiliang Li

Electrical & Computer Engineering Faculty Publications

Metal-Oxide-Semiconductor (MOS) capacitors with Bi₂Te₃ thin film sandwiched and embedded inside the oxide layer have been fabricated and studied. The capacitors exhibit ferroelectric-like hysteresis which is a result of the robust, reversible polarization of the Bi₂Te₃ thin film while the gate voltage sweeps. The temperature-dependent capacitance measurement indicates that the activation energy is about 0.33 eV for separating the electron and hole pairs in the bulk of Bi₂Te₃, and driving them to either the top or bottom surface of the thin film. Because of the fast polarization speed, potentially excellent …

Stm Study Of Pulsed Laser Assisted Growth Of Ge Quantum Dot On Si(1 0 0)-(2 × 1), Ali Orguz Er, Hani E. Elsayed-Ali

Electrical & Computer Engineering Faculty Publications

Ge quantum dot formation on Si(1 0 0)-(2 × 1) by nanosecond pulsed laser deposition under laser excitation was investigated. Scanning tunneling microscopy was used to probe the growth mode and morphology. Excitation was performed during deposition using laser energy density of 25-100 mJ/cm ². Faceted islands were achieved at a substrate temperature of ∼250 °C only when using laser excitation. The island morphology changes with increased laser excitation energy density although the faceting of the individual islands remains the same. The size of the major length of islands increases with the excitation laser energy density. A purely electronic …

Numerical Analysis And Design Optimization Of Organic Bulk Hetero-Junction Solar Cells Using The Mixed Finite Element And Arc-Length Methods, James L. Dean

Mechanical & Aerospace Engineering Theses & Dissertations

Due to the high coupling and non-linear nature of the semiconductor equations, numerical stability becomes a major problem when using a purely Newtonian numerical method in solving these equations. Presented is a robust mixed finite element formulation with application for organic solar cell devices that incorporates the arc-length predictor-corrector method to bypass such stability issues. The simulated device represents a multilayered solar cell using organic bulk hetero-junction materials including donor materials Poly[2,1,3-benzothiadiazole-4,7-diyl[4,4-bis(2-ethylhexyl)-4H-cyclopenta[2,1-b:3,4- b']dithiophene-2,6-diyl]] (PCPDTBT) and poly 3-hexylthiophene (P3HT) with acceptor fullerene materials [6,6]-phenyl C61 butyric acid methyl ester (PC61BM) or [6,6]-phenyl C71 butyric acid methyl ester (PC71BM) as the photoactive …

Electronically Enhanced Surface Diffusion During Ge Growth On Si(100), Ali Orguz Er, Hani E. Elsayed-Ali

Physics Faculty Publications

The effect of nanosecond pulsed laser excitation on surface diffusion during the growth of Ge on Si(100) at 250 °C was studied. In situ reflection high-energy electron diffraction was used to measure the surface diffusion coefficient while ex situ atomic force microscopy was used to probe the structure and morphology of the grown quantum dots. The results show that laser excitation of the substrate increases the surface diffusion during the growth of Ge on Si(100), changes the growth morphology, improves the crystalline structure of the grown quantum dots, and decreases their size distribution. A purely electronic mechanism of enhanced surface …

Excitation-Induced Germanium Quantum Dot Formation On Si (100)-(2×1), Ali Oguz Er, Hani E. Elsayed-Ali

Physics Faculty Publications

The effect of nanosecond pulsed laser excitation on the self-assembly of Ge quantum dots grown by pulsed laser deposition on Si (100)-(2×1) was studied. In situ reflection high-energy electron diffraction and ex situ atomic force microscopy were used to probe the quantum dot structure and morphology. At room temperature, applying the excitation laser decreased the surface roughness of the grown Ge film. With surface electronic excitation, crystalline Ge quantum dots were formed at 250 °C, a temperature too low for their formation without excitation. At a substrate temperature of 390 °C, electronic excitation during growth was found to improve the …

Activation Energy Of Surface Diffusion And Terrace Width Dynamics During The Growth Of In (4×3) On Si (100) - (2×1) By Femtosecond Pulsed Laser Deposition, M. A. Hafez, H. E. Elsayed-Ali

Electrical & Computer Engineering Faculty Publications

The nucleation and growth of indium on a vicinal Si (100) - (2×1) surface at high temperature by femtosecond pulsed laser deposition was investigated by in situ reflection high energy electron diffraction (RHEED). RHEED intensity relaxation was observed for the first ∼2 ML during the growth of In (4×3) by step flow. From the temperature dependence of the rate of relaxation, an activation energy of 1.4±0.2 eV of surface diffusion was determined. The results indicate that indium small clusters diffused to terrace step edges with a diffusion frequency constant of (1.0±0.1) × 10¹¹ s^-1. The RHEED specular …

Nonthermal Laser-Induced Formation Of Crystalline Ge Quantum Dots On Si(100), M. S. Hegazy, H. E. Elsayed-Ali

Electrical & Computer Engineering Faculty Publications

The effects of laser-induced electronic excitations on the self-assembly of Ge quantum dots on Si (100) - (2×1) grown by pulsed laser deposition are studied. Electronic excitations due to laser irradiation of the Si substrate and the Ge film during growth are shown to decrease the roughness of films grown at a substrate temperature of ∼120 °C. At this temperature, the grown films are nonepitaxial. Electronic excitation results in the formation of an epitaxial wetting layer and crystalline Ge quantum dots at ∼260 °C, a temperature at which no crystalline quantum dots form without excitation under the same deposition conditions. …

Band Gap Engineering Of Two Dimensional Silicon Photonic Crystals By Oxidation And Oxide Etching, Makhin Thitsa

Electrical & Computer Engineering Theses & Dissertations

In this thesis a thorough analysis is presented on the effects of oxidation and oxide etching on the band structure of two dimensional silicon photonic crystals (2 D Si PC's). By using the plane wave expansion method (PWM), two structures of triangular lattice, namely, air cylinders embedded in a silicon background and silicon cylinders embedded in an air background are modeled. The thesis focuses on triangular lattice arrangement because for certain parameter values such a lattice can give rise to absolute band gap, which prohibits the propagation of either transverse electric (TE) or transverse magnetic (TM) polarizations.

During oxidation three …

Formation Of In- (2×1) And In Islands On Si (100) - (2×1) By Femtosecond Pulsed Laser Deposition, M. A. Hafez, H. E. Elsayed-Ali

Electrical & Computer Engineering Faculty Publications

The growth of indium on a vicinal Si (100) - (2×1) surface at room temperature by femtosecond pulsed laser deposition (fsPLD) was investigated by in situ reflection high-energy electron diffraction (RHEED). Recovery of the RHEED intensity was observed between laser pulses and when the growth was terminated. The surface diffusion coefficient of deposited In on initial two-dimensional (2D) In- (2×1) layer was determined. As growth proceeds, three-dimensional In islands grew on the 2D In- (2×1) layer. The RHEED specular profile was analyzed during film growth, while the grown In islands were examined by ex situ atomic force microscopy. The full …

Melting And Solidification Study Of As-Deposited And Recrystallized Bi Thin Films, M. K. Zayed, H. E. Elsayed-Ali

Electrical & Computer Engineering Faculty Publications

Melting and solidification of as-deposited and recrystallized Bi crystallites, deposited on highly oriented 002-graphite at 423 K, were studied using reflection high-energy electron diffraction (RHEED). Films with mean thickness between 1.5 and 33 ML (monolayers) were studied. Ex situ atomic force microscopy was used to study the morphology and the size distribution of the formed nanocrystals. The as-deposited films grew in the form of three-dimensional crystallites with different shapes and sizes, while those recrystallized from the melt were formed in nearly similar shapes but different sizes. The change in the RHEED pattern with temperature was used to probe the melting …

Growth Of Ge Quantum Dots On Si(100)-(2×1) By Pulsed Laser Deposition, M. S. Hegazy, H. E. Elsayed-Ali

Electrical & Computer Engineering Faculty Publications

Self-assembled germanium quantum dots (QDs) were grown on Si(100)-(2×1) by pulsed laser deposition. In situ reflection-high energy electron diffraction (RHEED) and postdeposition atomic force microscopy are used to study the growth of the QDs. Several films of different thicknesses were grown at a substrate temperature of 400 °C using a Q-switched Nd:yttrium aluminum garnet laser (λ= 1064 nm, 40 ns pulse width, 23 J/cm ² fluence, and 10 Hz repetition rate). At low film thicknesses, hut clusters that are faceted by different planes, depending on their height, are observed after the completion of the wetting layer. With increasing film thickness, …

Self-Assembly Of Ge Quantum Dots On Si(100)- 2×1 By Pulsed Laser Deposition, M. S. Hegazy, H. E. Elsayed-Ali

Electrical & Computer Engineering Faculty Publications

Self-assembled Ge quantum dots are grown on Si(100)- 2×1 by pulsed laser deposition. The growth is studied by in situ reflection high-energy electron diffraction and postdeposition atomic force microscopy. After the completion of the wetting layer, transient hut clusters, faceted by different planes, are observed. When the height of these clusters exceeded a certain value, the facets developed into {305} planes. Some of these huts become {305}-faceted pyramids as the film mean thickness was increased. With further thickness increase, dome clusters developed on the expense of these pyramids. © 2005 American Institute of Physics. [DOI: 10.1063/1.1949285]

Study Of Transport Properties Of Inas Using Monte Carlo Simulation, Satyanadh Gundimada

Electrical & Computer Engineering Theses & Dissertations

The present research is aimed at ascertaining the usefulness of InAs semiconductor material for single photon avalanche photo detectors operating in the Geiger mode at 2 μm wavelengths. InAs is considered as the material suitable for the purpose because of its less bandgap and lower effective mass of the electrons when compared to other semiconductor materials presently in use. Hence, theoretically transient transport properties of bulk InAs are superior and the velocity overshoot phenomena stronger. InAs is a relatively less explored material when compared to other materials like GaAs. The choice of the material is justified with thorough exploration of …

Optical Properties Of Wide Band Gap Indium Sulphide Thin Films Obtained By Physical Vapor Deposition, N. Barreau, S. Marsillac, J. C. Bernède, T. Ben Nasrallah, S. Belgacem

Electrical & Computer Engineering Faculty Publications

Thin films of indium sulphide containing oxygen have been synthesized following a dry physical process. The constituents are deposited by thermal evaporation on glass substrates and then annealed under argon flow. Polycrystalline β-In₂S₃ containing oxygen thin films are obtained as soon as the temperature of annealing is between 623 and 723 K. In this paper, these β-In₂S₃ thin films have optically been studied. The optical band gap is direct. Its value is not dependent on the temperature of annealing. It is about 2.8 eV, which is higher than that of β-In₂S_{3 …}

Evaluation Of The Transport Properties Of Gasb For Bipolar Applications Through Monte Carlo Simulations, Damayanthi Palaniappan

Electrical & Computer Engineering Theses & Dissertations

GaAs is currently the semiconductor material of choice for high speed, low power applications. Its electronic transport properties are superior to almost all other semiconductors. It is also used in a variety of bipolar applications such as photodetectors and photo-mixers. However, as is well known, the hole mobility and related transport parameters of GaAs are not very good. This is a serious drawback, and poses a potential problem for all applications involving bipolar conductivity. In order to increase the high :frequency limits and high-speed capability of bipolar devices, the choice of an alternative material, therefore, becomes necessary. An important first …

Optical And Electrical Properties Of Cualse² Thin Films Obtained By Selenization Of Cu/Al/Cu... Al/Cu Layers Sequentially Deposited, J. C. Bernède, S. Marsillac, C. El Moctar, A. Conan

Electrical & Computer Engineering Faculty Publications

Optical and electrical properties of CuAlSe₂ thin films obtained by selenization of Cu/Al/Cu...Al/Cu layers sequentially deposited have been investigated. It is shown that the expected energy gap (2.67 eV) is measured for well crystallized films, whereas a slightly higher value is measured for films not so well crystallized. Raman diffusion also shows differences between well and poorly crystallized films with peaks corresponding to the reference powder for the former samples. A p-type conductivity is found whatever the crystalline quality of the samples. The conductivity of the films depends also strongly on their crystalline properties. When the films are badly …

Cualse² Thin Films Obtained By Chalcogenization, S. Marsillac, K. Benchouk, C. El Moctar, J. C. Bernède, J. Pouzet, A Khellil, M. Jamali

Electrical & Computer Engineering Faculty Publications

CuAlSe₂ thin films have been synthesized by chalcogenization of thin Cu and Al layers sequentially deposited by evaporation under vacuum. It is shown that CuAlSe₂ films are obtained with some Cu₂-_δSe and Se phases present at the surface. These surface phases are suppressed by annealing under vacuum and by chemical etching in a KCN solution. At the end of the process, the XRD spectrum demonstrates that textured CuAlSe₂ films have been obtained with preferential orientation of the crystallites along the (112) direction. The gap of the films is 2.7 eV as expected. The …

The Current Voltage Characteristics Of Electron Beam Controlled Thin Film Diamond Switches, Christopher Anthony Molina

Electrical & Computer Engineering Theses & Dissertations

The dark current of natural diamond thin films and the induced current due to electron-beam irradiation was measured up to a range of 7000Ncm'. The contact material was aluminum, annealed and unannealed. Switching experiments were performed with electron energies ranging from 70keV to 172keV. The switching results obtained are strongly dependent on the biasing polarity, incident electron energy, and whether the contact is blocking or Ohmic in nature. A simple model which takes traps into consideration allows us to explain the various switching responses. The range of electrons which define, in part, the switch mode was measured for one sample …

Transient Simulations And Modelling Of Semi-Insulating Gaas Photoconductive Switches, Prasun Kumar Raha

Electrical & Computer Engineering Theses & Dissertations

The primary objective of this thesis is to develop a one-dimensional transient simulator for Photoconductive Semiconductor Switches (PCSS) taking into consideration the material characteristics, the internal physical effects, and the external circuit. Simulations have been performed to study the device behavior at different voltage levels for copper-doped silicon-compensated GaAs material, though other materials could easily be simulated by changing the parameters. The model includes hole transport, and the results demonstrate the effect of hole injection, with and without recombination centers. In addition to developing a one-dimensional transient simulator, the role of various physical effects, such as the field-dependence of trapping …

Light Injection From An Active Cladding To The Core Of A Fiber Optic Fluorosensor, Alvin Leon Bryant

Electrical & Computer Engineering Theses & Dissertations

A fluorosensor works on the basis of light injection from the clad into the core of an optical fiber. The sensitivity of such a sensor depends on the efficiency of light injection. Conditions necessary for a high injection efficiency are experimentally determined. The refractive index difference between the core and the clad,ⁿcore ^-nclad, must be maximized to achieve a high injection efficiency. Since an air clad has the least refractive index, a bare core fiber will have a maximum efficiency. Standard optical fibers used for communication employ a minimum value for ⁿcore ^-nclad, in order …

Study Of Single-Fiber Fiber Optic Lever Microphone, Trung Duc Nguyen

Electrical & Computer Engineering Theses & Dissertations

Fiber optic sensors are widely used in today's technological applications, providing many advantages that conventional sensors lack. In particular, there is a demand in hypersonic applications to develop microphones to measure acoustic pressure that performs in high temperature and noisy surroundings. This thesis analyzes fiber optic lever microphones (FOLM), since they perform at high temperatures. An FOLM system is an intensity modulated sensor, which is simple to implement and is small in size. Two models of the FOLM have been fabricated and calibrated. The first model uses a seven-element fiber array while the second uses a single-fiber to transmit and …

A Novel Technique For Deep Level Characterization Of High-Resistivity Semiconductor Materials, Sridhar Panigrahi

Electrical & Computer Engineering Theses & Dissertations

An improved photo induced current transient spectroscopy (PICTS) technique is developed for studying deep level parameters in high-resistivity semiconductor materials. A new digital data acquisition approach and improvement in the cryogenics of the system have enabled us, for the first time in our laboratory, to detect CuA level in a copper doped silicon compensated gallium arsenide (GaAs:Si:Cu) sample. The digital approach improves both the signal to noise ratio (S/N) and the efficiency of the system. Also, multiple PICTS spectra in a single thermal cycle can be obtained. In the present work, various doped and undoped gallium arsenide ( GaAs) and …

Cathodoluminescence Of Gaas, Tyler Smith

Electrical & Computer Engineering Theses & Dissertations

Cathodoluminescence of band-gap radiation across the bulk of a proposed semiconductor switch has been studied. Such a device relies on the efficient use of cathodoluminescence to modulate the conductivity of the switch. Diagnostics were configured to measure the intensity of band-gap radiation across the bulk of several switch samples. The measured results were compared to calculations based on a four energy level band-gap model which included two deep levels EL2 and HL10.

Q Improvement Of A 5.2 Ghz Te011 Cavity By Incorporating Y1Ba2Cu3O7-X, R. Joseph Leclear

Electrical & Computer Engineering Theses & Dissertations

Research is undertaken to apply high temperature superconducting material to improve the quality factor (Q) of a 5.2 GHz cylindrical resonant cavity. In particular, the approach is to electrophoretically deposit polycrystalline Y₁Ba₂Cu₃O_7-x (YBCO) on the conducting surface of the cavity cylinder. Spalling of the YBCO ceramic coating due to expansion and contraction of the cavity during sintering and testing is overcome by segmenting the cylinder. Results show that the Q of the cavity is increased over that of a copper cavity at temperatures below 60 K. At 20 K, improvement exceeds a factor …

Monte Carlo Simulation Of Millimeter-Wave Gunn Effect Oscillators, Ramani Vaidyanathan

Electrical & Computer Engineering Theses & Dissertations

Monte Carlo simulations have been carried out to investigate the performance of microwave Gunn oscillators. Three separate aspects of the simulation problem have been comprehensively addressed in this work. First, the presence of an external circuit has been self-consistently incorporated into the calculations. The inclusion of the external circuit facilitates a study of the circuit controlled regime, and correctly models effects arising from the time dependent boundary conditions. Secondly, microscopic details of the electronic relaxation mechanisms which ultimately control the frequency response limits, have been taken into account through an iterative Monte Carlo-Poisson scheme. This procedure overcomes a potential shortcoming …

Optical And High Electric Field Effects In Bulk Gallium Arsenide Switches, Randy Roush

Electrical & Computer Engineering Theses & Dissertations

During the past few years, bulk, photoconductive switching has become recognized as a viable topic for future research on moderate and high power switches. The two-pulse, or BOSS, concept relies on an excitation laser pulse, and a separate de-excitation pulse in conjunction with silicon doped, copper compensated, GaAs to create a variable temporal electrical pulse width. The research contained in this document provides information concerning the feasibility of the BOSS concept, as the switch is scaled to larger sizes, and higher voltage and current. The major concern will be the high voltage and current effects. The absorption length for 1064 …