Open Access. Powered by Scholars. Published by Universities.®
Other Materials Science and Engineering Commons™
Open Access. Powered by Scholars. Published by Universities.®
- Discipline
- Keyword
-
- Materials engineering (4)
- Corrosion (2)
- ASTM F75 Cobalt Chromium Alloy (1)
- Acid (1)
- Acoustics (1)
-
- Aluminum (1)
- Biaxial Bending (1)
- Borosilicate (1)
- Carbon Fiber (1)
- Carbon fiber composites (1)
- Cast (1)
- Coating (1)
- Compliance (1)
- Composite (1)
- Fabricate (1)
- Flexural stress (1)
- Glass (1)
- Lighthouse (1)
- Materials Engineering (1)
- Nanoparticles (1)
- Plasmon resonance (1)
- Prism (1)
- Ribbon microphones (1)
- Silver Salts (1)
- Stainless Steel 316L (1)
- Tensile stress (1)
- Thermoplastic composites (1)
- Twist (1)
Articles 1 - 7 of 7
Full-Text Articles in Other Materials Science and Engineering
Biaxial & Twist Testing Of Composite Carbon-Fiber Sandwich Panels For Automotive Racing Vehicles, Erik Eckberg
Biaxial & Twist Testing Of Composite Carbon-Fiber Sandwich Panels For Automotive Racing Vehicles, Erik Eckberg
Materials Engineering
Composite sandwich panels were constructed with 4-ply plain weave carbon-fiber/epoxy face sheets in the 0o/45o/0o/45o orientation and 1/8th inch Nomex honeycomb core. The panels were cut into 5-inch square test plates for mechanical testing. All testing was done on a fixture designed and fabricated by Pratt & Miller Engineering and installed on an Instron testing system at Cal Poly. The twist test was performed by supporting diagonal corners of the plate while simultaneously loading the opposite two corners at a crosshead rate of .06 in/min (ASTM 3044-94R11). Out of 10 panels tested, …
Corrosion Of Stainless Steel 316l And Astm F75 Cobalt Chromium Alloy During Immersion Testing In Silver Salt Solutions, Meagan Higgins
Corrosion Of Stainless Steel 316l And Astm F75 Cobalt Chromium Alloy During Immersion Testing In Silver Salt Solutions, Meagan Higgins
Materials Engineering
This study evaluates the potential effects of silver salts on biocompatible metals used for prostheses during the chemical reduction process to produce a silver antimicrobial layer on the metal’s surface. Samples of two biocompatible metals were obtained: Stainless Steel 316L and ASTM F75 Cobalt Chromium Alloy. Three different silver salts were also acquired: silver nitrate, silver sulfadiazine, and silver chloride. Specimens of each metal were cut to size using a 4-1/2 inch aluminum oxide, 40 grit, cut off wheel for metal, attached to a Dewalt Angle Grinder. The biocompatible metal samples were then subject to either Solution 1, water with …
Fabricating Replacement Glass Prisms For The Piedras Blancas Lighthouse, Daniel Garcken
Fabricating Replacement Glass Prisms For The Piedras Blancas Lighthouse, Daniel Garcken
Materials Engineering
The objective of this project was to design and create a process for manufacturing replacement glass prisms for the Piedras Blancas lighthouse and several other lighthouses nationwide. The prisms were designed to be in multiple metal arrays spread across the floor of the beacon room (the topmost room of the lighthouses). The prisms functioned to transmit extra, radiant light from the beacon light through the floor of the beacon room and disperse it into the maintenance room below. Using computer aided drafting (CAD) software, an original prism was measured and modeled; the corresponding mold was also modeled. G-codes for controlling …
An Exploratory Investigation Into How Cold Working Can Affect The Acoustic Performance Of Thin Aluminum Foil In A Ribbon Microphone, Alexander (Alex) Stanley
An Exploratory Investigation Into How Cold Working Can Affect The Acoustic Performance Of Thin Aluminum Foil In A Ribbon Microphone, Alexander (Alex) Stanley
Materials Engineering
Ribbons of 4 μm thin 99.1% pure aluminum foil were cut and corrugated to replace the stock ribbon in an Apex 205 ribbon microphone. Prior to corrugation, half of the ribbons were sandwiched between two KimWipes and two pieces of cardstock then hammered to impart strain hardening. Each ribbon was placed into the microphone capsule and the frequency response of each ribbon was measured. A 10 second sine sweep from 20-20,000 Hz was played through a KRK Rokit 5 speaker and recorded through a ribbon microphone placed 6 inches away from the speaker cone. The signal generated by the ribbon …
The Synthesis And Characterization Of Gold And Silver Nanoparticles In Formal And Informal Settings, Mathew Wynn
The Synthesis And Characterization Of Gold And Silver Nanoparticles In Formal And Informal Settings, Mathew Wynn
Materials Engineering
Silver nanoparticles were synthesized through the reduction of AgNO3 using NaBH4. The borohydride anions were adsorbed onto silver nanoparticles. The repelling forces of the borohydride anions prevented the aggregation of particles, but the addition of an electrolyte or agitation induced aggregation. A yellow hue was given off by the silver nanoparticle sol that, using a spectrophotometer, had plasmon resonance at 386 nm. The silver nanoparticles were estimated to be 10 to 20 nm in diameter. Gold nanoparticles were synthesized through the reduction of HAuCl4 using Na3C6H5O7. The gold nanoparticle sol gave off a red hue that had plasmon resonance at …
Analyzing The Corrosion Resistance Of Ni-Shield 200 Coatings At Different Temperatures When Exposed To Sulphuric Acid, Alex Hussinger
Analyzing The Corrosion Resistance Of Ni-Shield 200 Coatings At Different Temperatures When Exposed To Sulphuric Acid, Alex Hussinger
Materials Engineering
Six steel samples each were twin wire arc sprayed with Hastelloy C-276 or Nickel-Shield 200 coatings approximately 0.020″ thick. These samples were then cut into 3″ by 3″ squares. A 2″ diamond grit hole saw was used to abrade and polish to a smooth surface a ring in the middle in order to get an O-ring mechanical seal. The samples were then weighed and loaded into a jig that started from the bottom up with a stainless steel plate, then the sample, then a Viton O-ring, a ¾″ thick glass plate with a 1 3/4″ hole cut in it, another …
Correlation Between 90o Tensile And 90o Flexural Properties For Thermoplastic Based Carbon-Fiber Composites, Amy Lautenbach
Correlation Between 90o Tensile And 90o Flexural Properties For Thermoplastic Based Carbon-Fiber Composites, Amy Lautenbach
Materials Engineering
Thermoplastic matrix composites containing carbon fibers and 4 different resins (TP 1-TP 4) were tested in tension with the fibers at 90 degree to the longitudinal axis following ASTM D 3039-00. The tensile strengths varied from 5.07-13.87 ksi with TP 1 as the strongest, and TP 4 as the weakest. SEM images were taken of the fracture surface of the samples to explore the fiber-matrix interaction. The SEM images showed significantly more wetting of the fibers in the higher strength materials. The SEM images of the two stronger materials showed resin coating the fibers even after fracture while the two …