Other Materials Science and Engineering Commons^™

A Performance-Weighted Environmental Assessment Of Ultra-High-Volume Fly Ash Substitution In Portland Cement Concrete, Youngguk Seo, M.A. Karim, Teddy Tzvetkov, Joshua Hardy

Faculty Articles

Fly ash substitution for cement in Portland cement concrete (PCC) has been regarded as a sustainable solution, but its widespread application remains constrained by concerns over mechanical performance and durability of PCC, especially at higher replacement rates. This study evaluates PCC mixes incorporating fly ash Type C (FA-C) or Type F (FA-F) across cement replacement rates from 10% to 90%, tracking fresh-state workability, compressive strength, and surface electrical resistivity at 7, 14, and 28 curing days. A process-based life cycle assessment (LCA) with the TRACI 2.1 method quantified global warming potential (GWP, kg CO₂/m³) under a …

Next-Generation Computing Hardware: Advancements In Tantalum Oxide Reram For Ai And Neuromorphic Applications, Rajas Ravindra Mathkari

Electronic Theses & Dissertations (2024 - present)

The rapid development of artificial intelligence, machine learning, and data-intensive computing has exposed the fundamental limitations of conventional von Neumann architectures, in which energy and time are continuously lost transferring data between physically separate memory and processing units. In contrast, the human brain performs complex computations directly at the point of memory storage through billions of parallel synaptic connections, a paradigm known as in-memory computing. Realizing this in hardware requires memory devices that are fast, energy-efficient, non-volatile, and capable of storing multiple resistance levels in an analog manner. Resistive Random Access Memory (ReRAM) based on tantalum oxide (TaOx) is one …

Novel Approach For The Micro Cracks Detection Of Solar Wafers And Cells, Mohd Israil, Arvind Kumar Sharma, Ekta Gupta

Al-Bahir

This paper deals with the review of various existing technique for the microcracks detection in silicon solar cell and wafer. In addition to this, we proposed a novel approach for the machine learning technique for the inspection of the cracks those are existed in the solar cell and wafer and not able to detect by the naked eyes. There are many techniques have been developed by the various researchers around the world to inspect solar cells for defect. All the techniques discussed in this article having some features and some weakness too. This paper present here gives the two-fold solution …

Surface Morphology And Moisture Adsorption/Desorption Characteristics Of Hybrid-Dielectric Moisture Sensors, Ronak Ali

Theses and Dissertations--Electrical and Computer Engineering

Relative humidity sensors are used for high-humidity measurement. Moisture sensors, or dew point sensors are used for low-humidity measurement (< 1 ppm_v). The dissertation contains two parts of studies. In the first part, the effect of surface morphology on the response speed of moisture sensors is studied. Moisture sensors using α-Al₂O₃ films as porous dielectric materials deposited by anodic spark deposition are studied. In this part of the study, a variety of small pores have been studied to investigate the response speed of moisture sensors. Three different surface morphologies have been studied using scanning electron microscopy. One …

Investigation Of Conductive Die-Top Thermal Capacitors During Short Circuit Operation Of Silicon Carbide Devices, Youssef Abotaleb

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

Silicon carbide (SiC) power devices have garnered significant attention in recent years due to their superior thermal and electrical properties compared to traditional silicon devices. However, SiC power devices suffer from severe reliability issues arising from their mechanical properties. This is because the Young's modulus of SiC is about three times larger than that of silicon, which correspondingly raises the mechanical stresses acting on the bonding structure, often leading to device failure under power shock events.

Traditional packaging materials and designs tend to constrain SiC performance, as hot-spot temperature resulting from a power shock is one of the key factors …

Surface Treatments' Effects On The Capacitor's Dielectric Performance Under Electro-Thermal Stresses, Haider. M. Umran, Feipeng Wang

Karbala International Journal of Modern Science

Biaxial-oriented polypropylene (BOPP) films are characterized by unfavorable aging behavior because of their poor susceptibility to high temperatures, humidity, and high electric fields. This makes them unqualified to withstand harsh operating conditions, such as in capacitor applications. This study investigates the impact of annealing BOPP samples at 100 °C for five hours after fluorination at different times (15, 30, and 60 minutes) on their electrical and mechanical performance under electro-thermal stresses. Scanning electron microscope (SEM) images confirm that there is an increase in surface roughness and the formation of a dense layer of fluorine-containing groups monotonically with fluorination time. So, …

Machine-Learning-Assisted Design Of Deep Eutectic Solvents Based On Uncovered Hydrogen Bond Patterns, Usman Lame Abbas, Yuxuan Zhang, Joseph Tapia, Md Selim, Jin Chen, Jian Shi, Qing Shao

Markey Cancer Center Faculty Publications

Non-ionic deep eutectic solvents (DESs) are non-ionic designer solvents with various applications in catalysis, extraction, carbon capture, and pharmaceuticals. However, discovering new DES candidates is challenging due to a lack of efficient tools that accurately predict DES formation. The search for DES relies heavily on intuition or trial-and-error processes, leading to low success rates or missed opportuni- ties. Recognizing that hydrogen bonds (HBs) play a central role in DES formation, we aim to identify HB features that distinguish DES from non-DES systems and use them to develop machine learning (ML) models to discover new DES systems. We first analyze the …

Application Of Quantum Algorithms In The Synthesis Of Dynamic Objects, Noilakhon Yakubova

Chemical Technology, Control and Management

Around the world, the food industry is focusing on achieving energy and resource efficiency. One of the main challenges in the field of process automation is the creation of effective control systems using intelligent technologies to improve the quality of processes and achieve the production of high-quality products with less energy and resources. Therefore, it is necessary to work with a large amount of data. Particular attention is paid to the development of computational algorithms for automated high-speed computational analysis systems for processing this data at high speed. Therefore, the article discusses the use of quantum computing methods in controlling …

Molecular Dynamics Study Of Characterization In Metal-Free Friction Materials, Yizhan Zhang

Electronic Theses and Dissertations

Metallic friction materials currently used in industry may adversely impact the environment. Substitutions for metals in friction materials, on the other hand, can introduce operational safety issues and other unforeseeable issues such as thermal-mechanical instabilities and insufficient strength. In view of it, this dissertation focuses on developing different kinds of materials from simple structure to complex structure and evaluating the material properties with the assistance of molecular dynamics (MD) tools at the nano scale.

First, the concept of the contacted surfaces in friction at the atomic scale was introduced in order to get accurate understanding of the friction process compared …

The Modernization Of Large Power Transformer Tanks, Babajide O. Williams

Electronic Theses and Dissertations

Due to the current demands placed on the power grid in terms of climate change, increasing urbanization, and terrorist attacks, the U.S. government in response to these demands, mandated that all the grid components be modernized in order to increase their reliability. As a critical component of the grid, Large Power Transformers (LPTs) play a key role in ensuring sustainable power generation and distribution. A literature search performed in this work and the analysis of data retrieved from the search showed that the tanks of these LPTs are critical to their durability, longevity, and reliability. Therefore, the reliability of LPTs …

Exploring The Potential Of Pavegen’S Kinetic Energy Generating Floor For Sustainable Energy Solutions: A Proposal For Cal Poly Slo, Brandon J. Cuneo

Construction Management

This paper proposes the installation of Pavegen's kinetic energy generating floors at Cal Poly’s campus as a sustainable energy solution. Pavegen has developed a pioneering technology that converts footsteps into clean and renewable energy. The versatility of these floors is demonstrated through successful implementations in various settings, such as transportation hubs and public spaces, generating power from foot traffic. Collaborations with Schneider Electric, installation at Dupont Circle, and integration at Heathrow Airport showcase the potential for sustainable urban infrastructure. This paper outlines research conducted on Pavegen and similar solutions, including communication with company representatives and examining proposed installation locations at …

The Study Of Corrosion On Additive-Manufactured Metals., Braydan Daniels

Electronic Theses and Dissertations

The purpose of this study was to investigate and compare the corrosion mechanisms between wrought and additive-manufactured (3D-printed) copper and stainless steel. The experimental procedure consisted of measuring the open circuit potential, electrochemical impedance spectroscopy, linear sweep voltammetry, Tafel analysis, surface topology, and scanning electron microscopy for each metal within salt water, tap water, sulfuric acid, and synthetic body fluid (excluding copper in synthetic body fluid).

Overall, printed stainless steel was more corrosion-resistant than wrought stainless steel in tap water and synthetic body fluid based on OCP, LSV, and surface topology results. Additionally, printed copper was more corrosion-resistant than wrought …

Surface Properties, Work Function, And Thermionic Electron Emission Characterization Of Materials For Next-Generation Dispenser Cathodes, Antonio Mantica

Theses and Dissertations--Chemical and Materials Engineering

A dispenser cathode’s ability to thermionically emit electrons is highly dependent on its material properties, especially those of the surface. Understanding the relationship between surface properties and electron emission, therefore, is vital to reach the next generation of the many vacuum electron devices (VEDs) that rely on the physics of electron emission. In the past century, many techniques have been developed to characterize material surfaces and quantify thermionic emission. These techniques are based on a wide range of different physical phenomena, including measuring photoemission via the photoelectric effect, measuring the electrostatic potential between metals in electrical contact, and current collection …

Fem Eem Dataset: Optimising Retrofitted Insulation For Irish Residential Building Walls, Rakshit D. Muddu, Aimee Byrne, Anthony Robinson Dr.

Datasets

A large number of combinations of Irish wall types, insulation materials, and heating fuel types were produced to compare the multiple variables which influence Optimal Insulation Thickness values. The total cost (TC) and carbon emission (CE) at optimum insulation thickness (OIT) for all combinations of insulation material and three types of fuel are considered. The dataset presents OIT for solid wall, cavity wall and cavity block wall types located in Monaghan, Dublin, and Kerry.

Challenges And Signal Processing Of High Strain Rate Mechanical Testing, Barae Lamdini

Theses and Dissertations

Dynamic testing provides valuable insight into the behavior of materials undergoing fast deformation. During Split-Hopkinson Pressure Bar testing, stress waves are measured using strain gauges as voltage variations that are usually very small. Therefore, an amplifier is required to amplify the data and analyze it. One of the few available amplifiers designed for this purpose is provided by Vishay Micro-Measurements which limits the user’s options when it comes to research or industry. Among the challenges of implementing the Hopkinson technology in the industry are the size and cost of the amplifier. In this work, we propose a novel design of …

Zero-Power Ac Current Sensor, Omar Aragonez

Mechanical Engineering ETDs

In this study, a magnetic piezoelectric cantilever powered AC current and frequency sensor is proposed. This paper covers the configuration of the experimental setup, finite element modeling of the magnetic coupling, and the optimal spatial location of the magnetic proof mass in relation to the wire for smart grid applications. Solid and stranded copper wires of various gauges were used and carried current up to 30A. The magnets act as a proof mass to lower the frequency while also coupling to the magnetic field generated by the current carrying wire. The frequency of the AC current produces a sinusoidal force …

Facile One-Step Hydrothermal Method For Nico2s4/Rgo Nanocomposite Synthesis For Efficient Hybrid Supercapacitor Electrodes, Ahmed Mysara, Sayed Y. Attia, Fouad I. El-Hosiny, M A. Sadek, Saad G. Mohamed, M M. Rashad

Nanotechnology Research Centre

Spinel nickel-cobalt sulfide (NiCo2S4) supported on reduced graphene oxide (rGO) was fabricated through a facile one-step hydrothermal method for energy storage applications. The distribution of the NiCo2S4 nanoparticles on the rGO surface was found to improve the supercapacitive performance of the assembled device. The NiCo2S4/rGO nanocomposite exhibits outstanding electrochemical behavior with a capacity (C)/specific capacitance (Cs) of 536 C g−1/1072 F g−1 at a current density of 1 A g−1. To further investigate the electrochemical behavior of the NiCo2S4/rGO nanocomposite, a hybrid supercapacitor (HSC) was constructed utilizing a NiCo2S4/rGO positive electrode and an activated carbon …

A Computational Exploration Of The Scandate Cathode Surface, Shankar Miller-Murthy

Theses and Dissertations--Chemical and Materials Engineering

The exact surface configuration of scandate cathodes has been a point of contention for the materials community for a long time. Without proper understanding of it and the related structures and emission mechanisms, scandate cathodes remain patchy and unreliable emitters. Thus, density functional theory techniques were applied to various potential surface arrangements and found that there are several low-energy surfaces with low work functions that incorporate a scandium interlayer between tungsten and oxygen or otherwise have a scandium-on-tungsten structure. Furthermore, it was discovered that adding a monolayer of scandium directly to a tungsten surface is surprisingly favorable, thermodynamically. While none …

Modeling, Fabrication, And Characterization Of Rf-Based Passive Wireless Sensors Composed Of Refractory Semiconducting Ceramics For High Temperature Applications, Kavin Sivaneri Varadharajan Idhaiam

Graduate Theses, Dissertations, and Problem Reports (ETD)

Real-time health monitoring of high temperature systems (>500^oC) in harsh environments is necessary to prevent catastrophic events caused by structural failures, varying pressure, and chemical reactions. Conventional solid-state temperature sensors such as resistance temperature detectors (RTDs) and thermocouples are restricted by their operating environments, sensor dimensions and often require external power sources for their operation. The current work presents the research and development of RF-based passive wireless sensing technology targeting high temperatures and harsh environmental conditions. Passive wireless devices are generally classified as near-field and far-field devices based on the interrogation distance. Near-field sensors are placed at …

Simulation And Fabrication Of All Oxide-Based Ito/Tio2/Cuo/Au Heterostructure For Solar Cell Applications, Sajal Islam

Graduate Theses/Dissertations

Oxide heterostructures have drawn great attention lately, due to their environment-friendly properties and potential applications in optoelectronic devices. In this work, a simulation study of a heterojunction solar cell was performed with SCAPS (a solar cell simulator) using TiO2 as an n-type and CuO as a p-type layer. The thickness and the dopant-dependent simulations have shown that the solar cell operates at a maximum efficiency of 19.2% when the thickness of the TiO2/CuO layers is chosen 1.4µm/1.2µm compared to the 11.5% efficiency when FTO is replaced with ITO. An indium-doped tin oxide (ITO) vs fluorine-doped tin oxide (FTO) comparison study …

Husky Hand: A Low-Cost Electro-Mechanical Prosthetic Arm For The Underprivileged, Adam Robert

Thinking Matters Symposium

A continuation of a low-cost prosthetic upper limb prototype design which was investigated in EGN 301. The prosthetic is specifically designed for the needs and requirements of under privileged individuals in the Dominican Republic with upper limb amputations. The project focuses on the creation of an open-source computer aided prosthetic hand/arm model. The design allows consumer-grade fused filament fabrication (FFF) 3-D printers to be used. The improved design allows for the integration of the PQ-12 linear actuator for grasp and finger control. This simplifies the assembly, while, also reducing the size and mass of the whole unit. Producing a low-cost …

Molecular To Macroscopic Understanding Of Chloroaluminate Anion Intercalation In Rechargeable Aluminum-Graphite Batteries, Jeffrey Xu

Dissertations and Theses

Today’s global energy challenges pose an urgent need to electrify transportation and better store intermittent renewable energy sources (e.g., solar and wind energy). For such large-scale battery applications, aluminum batteries are a promising “beyond lithium-ion” technology due to the high volumetric capacity, earth abundance, low-cost, and inherent safety of aluminum metal. However, there are very few compatible positive electrode materials that exhibit high energy density and cycling stability, in part due to the challenges of electrochemically intercalating highly charged Al³⁺ cations. Recently, graphite has been demonstrated as a promising positive electrode material in non-aqueous rechargeable aluminum batteries, which store …

Perovskite Thin Films Annealed In Supercritical Fluids For Efficient Solar Cells, Gilbert Annohene

Theses and Dissertations

In the field of photovoltaics, scientists and researchers are working fervently to produce a combination of efficient, stable, low cost and scalable devices. Methylammonium lead trihalide perovskite has attracted intense interest due to its high photovoltaic performance, low cost, and ease of manufacture. Their high absorption coefficient, tunable bandgap, low-temperature processing, and abundant elemental constituent provide innumerable advantages over other thin film absorber materials. Since the perovskite film is the most important in the device, morphology, crystallization, compositional and interface engineering have been explored to boost its performance and stability. High temperatures necessary for crystallization of organic-inorganic hybrid perovskite films …

Treated Hfo2 Based Rram Devices With Ru, Tan, Tin As Top Electrode For In-Memory Computing Hardware, Yuvraj Dineshkumar Patel

Theses

The scalability and power efficiency of the conventional CMOS technology is steadily coming to a halt due to increasing problems and challenges in fabrication technology. Many non-volatile memory devices have emerged recently to meet the scaling challenges. Memory devices such as RRAMs or ReRAM (Resistive Random-Access Memory) have proved to be a promising candidate for analog in memory computing applications related to inference and learning in artificial intelligence. A RRAM cell has a MIM (Metal insulator metal) structure that exhibits reversible resistive switching on application of positive or negative voltage. But detailed studies on the power consumption, repeatability and retention …

New Metal Based Saturable Absorber For Ultrashort Pulse Generation, Muhammad Taufiq Ahmad

Student Works (2020-2029)

Cost-efficient, robust and flexible laser systems are vital for a wide-range of applications ranging from high-precision material processing to biomedicine. This thesis aims to explore pure silver and gold based saturable absorbers (SAs) as Q-switcher and mode-locker in various fibre laser cavities. The generations of Q-switched pulses in 1-,1.55-, and 2-micron regions have been successfully demonstrated using a pure gold, which was deposited using electron beam deposition onto a PVA thin-film as SA. For instance, a stable Q-switched thulium-doped fibre laser (TDFL) operating at 1949 nm was successfully demonstrated with the gold SA. The proposed laser generates Q switched pulses …

Optimized Transconductance Designs To Enhance The Linearity Performance Of Rf Front-End Receiver Circuits In 130 Nm Cmos Technology, Nandini Vitee

Student Works (2020-2029)

Highly linear front-end circuits are greatly desired for wireless receivers to improve the dynamic range. However, intermodulation distortions caused by the non-linear transconductor current limits the linearity of the front-end receiver circuit in CMOS technologies. In addition to the inherent nonlinear effect, the downscaling of CMOS further exacerbates the linearity of the circuit due to lower voltage headroom and high-field mobility. Thus, it is essential to develop effective circuit techniques that can aid linearity enhancement without jeopardizing other preferred performances such as low noise, high conversion gain, and low-power consumption. In this thesis, two different high linear transconductors are presented …

A Brief Bibliometric Survey On Circularly Polarized Antennas For Mobile Communication, Aniket Gunjal, Abhaya Pal Singh

Library Philosophy and Practice (e-journal)

This paper presents a database review on “Circularly Polarized Antennas for Mobile Communication” as it is the emerging technique used by mobile service provider because of having benefits over other types of antennas available.The polarization purity is now the major issue. In some cases due to cross polarization issue the antenna signal is cancelled at receiver side.So, it is necessary to have circularly polarized antenna to avoid this polarization issue because of change in phase of signal. The change in phase of signal is due to striking of wave on the obstacles and it slightly tilted from its direction causes …

Tabletop Mechanical Tester, Jamie Dombroski, Brian English, Richard Leffler, Andrew Shirk

Williams Honors College, Honors Research Projects

The need for hands-on and face-to-face experiences in the engineering classroom is very great. The equations, principles, and concepts can all be learned, but without the visual and tactile application, these don’t always sink in or become concrete. A small-scale tensile test machine was designed, sourced, manufactured, and tested for the purpose of being applied in classroom settings to provide this experience to engineering students. Extensive research was performed concerning tensile machines on the market, the essential elements of which are the load cell, grips, crosshead, extensometer, motor, and frame. The raw materials for the frame were purchased and drawings …

Development Of A Sonically Powered Biodegradable Nanogenerator For Bone Regeneration, Avi S. Patel

University Scholar Projects

Background: Reconstruction of bone fractures and defects remains a big challenge in orthopedic surgery. While regenerative engineering has advanced the field greatly using a combination of biomaterial scaffolds and stem cells, one matter of difficulty is inducing osteogenesis in these cells. Recent works have shown electricity’s ability to promote osteogenesis in stem cell lines when seeded in bone scaffolds; however, typical electrical stimulators are either (a) externally housed and require overcomplex percutaneous wires be connected to the implanted scaffold or (b) implanted non-degradable devices which contain toxic batteries and require invasive removal surgeries.

Objective: Here, we establish a biodegradable, piezoelectric …

Development Of A Sonically Powered Biodegradable Nanogenerator For Bone Regeneration, Avi Patel

Honors Scholar Theses

Background: Reconstruction of bone fractures and defects remains a big challenge in orthopedic surgery. While regenerative engineering has advanced the field greatly using a combination of biomaterial scaffolds and stem cells, one matter of difficulty is inducing osteogenesis in these cells. Recent works have shown electricity’s ability to promote osteogenesis in stem cell lines when seeded in bone scaffolds; however, typical electrical stimulators are either (a) externally housed and require overcomplex percutaneous wires be connected to the implanted scaffold or (b) implanted non-degradable devices which contain toxic batteries and require invasive removal surgeries.

Objective: Here, we establish a biodegradable, piezoelectric …