Metallurgy Commons^™

Understanding Heterogeneous Nucleation In Iron Alloys From First Principles: A Review And Discussion, Semen Naumovich Lekakh

Materials Science and Engineering Faculty Research & Creative Works

Heterogeneous nucleation during solidification plays a key role in structure formation of different types of iron-based alloys, including steels and cast irons. A review summarizes the novel theoretical methods which were used to understand the nature of heterogeneous nucleation in iron-based alloys. An ab initio simulation of atomic adsorption was used to predict the activity of heterogeneous nuclei, and the thermodynamic methods were applied to design conditions for desired precipitate formation in the iron melts. A high-resolution TEM study of individual nucleus and statistics of nuclei family, obtained from an automated SEM/EDX analysis, illustrates a possibility to design processes of …

Evaluating The Effectiveness Of Stay-In-Place Forms To Improve The Tosional Stability Of Box Beam Bridges During Erection, Karl E. Barth, Michael W. Seek, Gregory K. Michaelson, Dimitra Pyrialakou, Brook T. Woldegabriel

Engineering Technology Faculty Publications

Cold-formed tub girders provide an effective steel solution for short-span bridges. The girders are often delivered with an open top with stay-in-place forms installed on site. Walkways may be installed to the side of the girder that can induce significant torsion rotations in the open cross section. Full scale tests on girder specimens have shown that installing one or two panels of stay in place forms at the ends of the girder can significantly reduce the torsion rotation of the girder by providing warping resistance. Cantilever tests on the stay in place forms are performed to investigate the influence of …

Potential Of Lidar And Hyperspectral Sensing For Overcoming Challenges In Current Maritime Ballast Tank Corrosion Inspection, Sergio Pallas Enguita, Jiajun Jiang, Chung-Hao Chen, Samuel Kovacic, Richard Lebel

Electrical & Computer Engineering Faculty Publications

Corrosion in maritime ballast tanks is a major driver of maintenance costs and operational risks for maritime assets. Inspections are hampered by complex geometries, hazardous conditions, and the limitations of conventional methods, particularly visual assessment, which struggles with subjectivity, accessibility, and early detection, especially under coatings. This paper critically examines these challenges and explores the potential of Light Detection and Ranging (LiDAR) and Hyperspectral Imaging (HSI) to form the basis of improved inspection approaches. We discuss LiDAR’s utility for accurate 3D mapping and providing a spatial framework and HSI’s potential for objective material identification and surface characterization based on spectral …

Improving Cast Steel Rail Coupler Fatigue Resistance Through Local Wire-Arc Additive Manufacturing, Andrew M. Bunge

Dissertations, Master's Theses and Master's Reports

Every year, thousands of cast-steel railcar couplers suffer from corrosion-initiated fatigue cracking in similar areas of the coupler’s knuckle; between 2015 and 2018 about 90,000 knuckles were replaced, otherwise these couplers would have been at risk for unexpected failures. These types of couplers have been common in industrial use as early as 1932, hence it is desirable for a countermeasure to the fatigue cracking that does not involve significantly altering the geometry or casting process. Wire arc additive manufacturing (WAM) is a developing technology which boasts the ability to produce complex near-net-shape components; however, less attention has been paid to …

Causational Analysis And Rectification Of Issues Concerning Scale Formation On Hot-Rolled Straight Bar Product And Its Effects On Ultrasonic Testing, Riley Mattix

Williams Honors College, Honors Research Projects

At Charter Steel's NDT Processing Plant located in Cleveland, Ohio, a concern has arisen regarding the recently implemented bar straightening and UT (Ultrasonic Testing) equipment. A substantial amount of mill scale, which is typically removed during the straightening process, is persisting on the bar’s surface throughout most of the NDT procedure. This lingering scale has been observed to flake off once inside the UT equipment, introducing unwanted noise and phantom peaks into the UT readings. Additionally, thick mill scale has been identified as a source of background interference in the received data. In contrast, bars that have been subjected to …

Cascaded Sapphire Fiber Bragg Gratings Inscribed By Femtosecond Laser For Molten Steel Studies, Dinesh Reddy Alla, Deva Prasad Neelakandan, Farhan Mumtaz, Rex E. Gerald, Laura Bartlett, Ronald J. O'Malley, Jeffrey D. Smith, Jie Huang

Electrical and Computer Engineering Faculty Research & Creative Works

This research reports a distributed fiber optic high-temperature sensing system tailored for applications in the steel industry and various other sectors. Recent advancements in optical sensor technology have led to the exploration of sapphire crystal fibers as a solution for sensing in harsh environments. Utilizing a femtosecond (fs) laser, cascaded fiber Bragg gratings (FBGs) were meticulously fabricated within a multimode sapphire optical fiber. These FBGs endowed the system with distributed sensing capabilities and underwent rigorous testing under extreme temperatures, reaching up to 1,800 °C. The study delves into the investigation of the FBG reflection spectrum, facilitated by the development of …

Integration Of Hadfield Steel Into Modern Body Armor, Jason T. Fridlund

ME 4133/6133 Mechanical Metallurgy

The increased lethality of recently fielded projectiles mandates a proportional escalation in armor performance. Recent advancements in ceramic technologies have allowed designers to incorporate harder but more brittle materials into hard armor designs to defeat yet more capable penetrating projectiles. Ceramics suffer from the feature of shattering, however, even when impacted by threats below their design parameters. While this shattering mechanism is used effectively to dissipate energy from high-energy rifle projectiles, it is wasted on low-energy projectiles, and can result in easily damaged lifesaving gear, both of which are undesirable in combat. In contrast, steel body armor has been used …

Characterization Of Hydrogen Embrittlement Sensitivity In High Hardness Steels, David Ahlen Salley

Theses and Dissertations

High hardness steels can be affected by delayed brittle cracking often attributed to hydrogen embrittlement. Improved resistance to hydrogen embrittlement would be beneficial to many industries including military, automotive, and high-rise construction. While other prevention methods include coating, trapping, and barriers, design efforts in this study were focused on improving intrinsic properties to be more resistant to hydrogen embrittlement. Four alloys targeting 477 – 534 HB were designed and produced in-house and compared against a commercial grade 500 HB alloy. Charpy V-notch (CVN) impact toughness and tensile specimens were made according to ASTM E23 and ASTM E8 to characterize mechanical …

Austenitic, Duplex, And Lean Duplex Stainless Steel Critical Pitting Temperature In Simulated Concrete Environment, Bobby Giebel

Williams Honors College, Honors Research Projects

In this work, the critical pitting temperature (CPT) will be observed for a selection of austenitic (316LN and 24100) and duplex (2205), and lean duplex (2304, 2001) stainless steels in simulated concrete pore solution. To study the influence of temperature on the pitting stability of the stainless steels, three temperatures were tested: 25oC, 45oC, and 65oC for cyclic potentiodynamic polarization (CPP) and electrochemical impedance spectroscopy (EIS). Electrochemical properties of the interfaces we studied via EIS analysis. Kinetics were studied via CPP testing. To reveal the critical pitting temperature of the stainless steels, cyclic thermammetry was used. Characterization of the pits …

Cold-Formed Steel Strength Predictions For Torsion, Yu Xia, Robert S. Glauz, Benjamin W. Schafer, Michael Seek, Hannah B. Blum

Engineering Technology Faculty Publications

Locally slender open cross-section members are susceptible to significant twisting and high warping torsion stresses. Torsion considerations are complicated by whether it is derived as a first-order effect from loading or a second-order effect from instability. Previous direct torsion experiments on lipped channels have shown significant inelastic reserve in limited cases. The current design for combined bending and torsion interaction has some limitations, including only considering the first yield in torsion and ignoring the cross-section slenderness in torsion. A parametric study is conducted to predict the torsion capacity in locally slender cross-sections. Shell finite element models of lipped Cee and …

The Process-Structure-Property-Performance Of Aisi 1020​, Jonathan Wellman, Tate James, Robbie Christman, Brian Broom

ME 4133/6133 Mechanical Metallurgy

AISI 1020 is widely used in many different industries due to its high strength, high ductility, high machinability, and good weldability. AISI 1020 has a number of applications. Low carbon steel can be used on a macroscale to build bridges, and low carbon steel can be used on smaller scales such as Lawnmower blades. Low carbon steel is the material of choice for lawn mower blades because of its ability to bend before it breaks. The ductile attribute of low carbon steel also has many other benefits.

Galvanic Corrosion In Aluminum/Steel Joints, Maegan Saul

Williams Honors College, Honors Research Projects

As car manufacturers seek to use lighter weight materials, aluminum is being more commonly used in the construction of vehicles. However, the strength of steel cannot be matched and both metals are necessary, leading to the joining of dissimilar metals. This connection of different metals leads to a galvanic coupling and subsequent corrosion of the less noble metal. This project aims to observe the corrosion and galvanic coupling behavior of aluminum alloys and carbon steel so that a model may be produced which can accurately predict the expected responses of the metals in various environments. Better, more accurate modeling of …

Optimization Of The Practice Of Slow Cooling Steel Bars: A Redesign And Modernization Of Materials, Eryn Johnston

Mechanical Engineering Undergraduate Honors Theses

Throughout the process of steel making, certain grades of steel are a higher risk for defects caused by the inability to quickly diffuse hydrogen through the steel when cooled to room temperature at a normal rate based on the ambient air temperature. To reduce the hydrogen flaking defects that are caused due to hydrogen entrapment in the steel, the process of slow cooling is utilized. This process reduces the cooling rate of steel bars by keeping them at a higher temperature for extended periods and in turn gives the hydrogen a chance to fully dissipate from the steel. In many …

Effect Of Wall Thickness And Build Quality On The Compressive Properties Of 304l Thin-Walled Structures Fabricated By Slm, Myranda Spratt, Sudharshan Anandan, Rafid M. Hussein, Joseph William Newkirk, K. Chandrashekhara, Heath Misak, Michael Walker

Materials Science and Engineering Faculty Research & Creative Works

The specific strength of lightweight lattice structures built with SLM is of interest to the aerospace industry. Honeycombs were manufactured with increasing wall thicknesses (which increases density) and tested under compression. The optimal strength to density ratio was determined from the resulting data. The build quality was also evaluated to determine how/if the results were influenced by the specimen quality. Differences between the nominal and as-built geometry were identified, but considered to be minimal. Microstructural evaluation of the specimens revealed a possible dependence on the ‘border scan’ properties, as the thickness of the specimens was such that the board scan …

Temper Response Of A Vanadium Microalloy Steel, Bradley W. Hostetler

Materials Engineering

This investigation details the effect of a quench-and-temper processing treatment on the mechanical properties of a microalloy steel being considered for use as a pipeline flange. Microalloy steels are normally processed via Thermo-Mechanically Controlled Processing (TMCP) due to the increased strength from ferrite grain refinement; however, the geometry of a pipeline flange requires post processing beyond TMCP which diminishes the strengthening effect provided by TMCP. The purpose of this research project is to determine the mechanical properties produced when a vanadium microalloy steel is quenched and tempered. The two major considerations are the effect of tempering time on properties and …

Process Development And Implementation For The Imaging Of Heat Treated A2 Steel For Consolidation Into An Atlas, Jessica Roberts

Senior Honors Projects, 2010-2019

Material processes, properties, and microstructure are interconnected, often visualized as the points of a triangle. Changing the process a material goes through will in turn change the properties and microstructure of that material. In materials research and education (specifically with metals), comparison between research or experiment results and scholarly-accepted results is important. When reading textbooks addressing different properties of metals and the process of metal treatment, images are often shown of the various microstructures associated with each property or process stage. The difficulty comes in trying to compare the stages or properties to one another; often different materials and processes …

Modelling The Softening Behaviour During Galvanizing Of Various Steel Grades, Kevin Banks, Rorisang Maubane, Thabang Makwena

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Modelling The Softening Behaviour During Galvanizing Of Various Steel Grades, Kevin Banks, Rorisang Maubane, Thabang Makwena

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Temperature Distributions Influencing Lateral Spread In Industrial Hot Rolling, Baohui Tian, Siegfried Kleber, Silvia Zinner, Peter Markiewicz

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

A Study On Non-Metallic Inclusions In Foundry Steel Process, Marc Leonard Harris

Masters Theses

"The effects of sample area and automated SEM/EDS feature analysis parameters (step size, magnification and threshold) on nonmetallic inclusion characterization results has been investigated and optimized. A post-processing program was developed to automatically determine average inclusion chemistry, total element concentrations within inclusions, and for generating joint ternary diagrams with size visualization for representing nonmetallic inclusion populations. Using these tools the evolution of nonmetallic inclusions was examined for 4320 steel at a participating industrial steel foundry. The steel was sampled throughout electric arc furnace melting through ladle refining to the final casting where an in-mold sampling procedure was developed to procure …

The Examination Of Stress Corrosion Cracking In High Strength Carbon Steel Through Combined Mechanical-Electrochemical Testing, Jacob Sines

Williams Honors College, Honors Research Projects

Through the analysis of materials and environments seen in industry a better understanding of the fundamentals behind degradation mechanisms can be observed. The scope of this project was to better understand the fundamentals behind the degradation of high strength pipeline steels in a lab setting to simulate an environment seen in industry. Specifically the degradation mechanisms of high and nearly neutral pH stress corrosion cracking were examined in environments that simulated oil and gas pipelines buried in soil. Experimentation was carried out utilizing X65 carbon steel specimen, a Gamry potentiostat, a CORTEST proof ring, a CORTEST slow strain rate machine, …

An Intercritical Heat Treatment Study Of High Strength, Microalloyed Ferrous Open Die Forgings, Kelly Elizabeth Stewart

Materials Engineering

High strength, low alloy steel is most commonly utilized in plate or sheet form-with a thickness under 4 in, one unconventional application however, is open die forging where cross-sectional area can be as large as 9.5 in by 11.5 in. When forging to larger section size than one would thermo-mechanically roll sheet steel, a new set of complications, such as variation in microstructure and mechanical properties, arise. This study investigates the heat treatment and processing options needed to negate the inherent microstructural irregularity and Charpy V-Notch (CVN) toughness variation. Intercritical heat treatment—normalizing and then quench and tempering above the A …

The Effects Of Heat Treatment On The Grain Growth, Phase Evolution, And Hardness Of Newly Developed Steel-Based Hardfacing Alloys For Industrial Applications, Renee Kuzniar

Materials Engineering

Steel-based hardfacing alloys are welded onto the outside diameter of tool joints in three beads with a slight overlap between welds for underground drilling to prolong the tool joints’ life. Current hardfacing alloys have a shortened life due to cracks occurring in neighboring weld beads. To decrease cracking, the effects of composition and heat treatment on the microstructure was investigated on five alloys. Five small arc-melt circular ingots roughly 1.4 x 0.3 inches were produced. Each sample had varying amounts of C, B, Cr, Mn, Mo, Nb, Si, Ti, V, and W. The carbon levels in the alloys were .91wt%, …

Bacterial Growth On Metal And Non-Metal Surfaces In A Static Bioreactor, Rolan Yuk Loong Liong

Master's Theses

Research was conducted to observe bacterial growth on the surface of metals in a static bioreactor. Metal and non-metal samples were subjected to bacterial exposure (1 day and 9 days). The metal samples were surface treated prior to bacterial exposure. The microstructures of the surface treated samples were analyzed by optical microscopy. After exposure, the microstructures of the samples were analyzed by scanning electron microscopy (SEM). The analysis suggested that microbial attachment on the surface was related to the underlying microstructure of steel. The preferential attachment of microbes could potentially be influenced by cathodic and anodic regions created by the …

Development Of Third Generation Advanced High Strength Steels, Meghan C. Mcgrath

Doctoral Dissertations

"Lightweight duplex steels with combinations of either bainite, acicular ferrite, and austenite or martensite and austenite were investigated as third generation advanced high strength steels targeted for automotive applications. Large additions of manganese (>13 wt%) and carbon (

Duplex steels with different volume fractions of primary δ -ferrite were used to study the crystallography of austenite formed during the peritectic reaction. Solute profiles across the peritectic interface showed aluminum segregated near the interface which promoted bainitic ferrite formation. Thermal treatments were used to manipulate the concentration and type of oxides and the ferrite plate density was found to correlate …

Friction Stir Lap Welded Advanced High Strength Steels: Microstructure And Mechanical Properties, M. Ghosh, K. Kumar, R. S. Mishra

Materials Science and Engineering Faculty Research & Creative Works

Friction stir welding was carried out under different heat input and cooling rates to produce lap joints between high strength martensitic steel sheets. the microstructure of the welds was characterized, and microhardness was evaluated. Joint efficiency was determined by lap shear test. Variation in processing conditions governed total heat input, peak temperature and cooling rate during friction stir welding. Weld nugget microstructure depended principally on cooling rate. the slowest cooling rate promoted ferrite-pearlite and the fastest cooling rate resulted in martensite formation in the weld nugget. the weakest region of all the joints was the heat affected zone, which consists …

Characterization Of Iron Oxides And Atmospheric Corrosion Of Steel, Sei Jin Oh

Physics Theses & Dissertations

The study of corrosion behavior was performed using three different analytical techniques, which provided information on the formation, development and layering of iron oxides on the corrosion products as a function of atmospheric conditions, exposure time and type of steel. In particular, the protective layer formed on weathering steel was investigated as a function of different amounts of alloying elements in the steel, atmospheric conditions and exposure times. Combined together, the results provided a better understanding of the atmospheric corrosion behavior of steel, and formed a part of database of the atmospheric corrosion characteristics.

Accurate characterization of the iron oxides …

Investigation Of Inclusions In Armco Ingot Iron, Edwin J. Duncan

Bachelors Theses and Reports, 1928 - 1970

Various chemical and electrolytic separation methods were investigated in an attempt to separate the in­clusions in Armco ingot iron. Residues obtained were X-rayed for identification purposes. The microstruc­tures of this iron were studied with the object of de­termining the relative sizes, locations, and possible compositions of the inclusions.

Studies Of Tempering Behavior Of Steel X-9165 Of N-A-X 9100 Series, James A. Ndulue

Bachelors Theses and Reports, 1928 - 1970

One of the reasons why steel is the most versatile of all the metals available for engineering applications is because of the wide range of properties that can be obtained from it by proper heat treatment.

Electroplating Of Chromium, Nickel And Copper Upon Titanium, Stanley O. Fong

Bachelors Theses and Reports, 1928 - 1970

Recently, there has been a great amount of research work done on the metal titanium. Since it is a light weight metal, with unusual strength and good resistance to corrosion, it may be a possible substitute for aluminum and magnesium alloys, or steel.