Metallurgy Commons^™

Theoretical Modeling Of Protective Oxide Layer Growth In Non-Isothermal Lead Alloy Coolant Systems, Yitung Chen, Jinsuo Zhang, Huajun Chen, Jichun Li

Transmutation Sciences Materials (TRP)

The goal of this research project is to provide a basic understanding of the protective oxide layer behaviors and to develop oxide layer growth models of steels in non-isothermal lead alloys (lead or lead-bismuth eutectic) coolant systems. Precise studies and simulations of all hydrodynamics with thermal conditions encountered in practical coolant loop systems by use of different flowing conditions in the laboratory are difficult and expensive, if not impossible. Therefore it is important and necessary to develop theoretical models to predict the protective oxide layer behaviors at the design stage of a practical lead-alloy coolant system, to properly interpret and …

Effect Of Welding Parameters On Properties Of 5052 Al Friction Stir Spot Welds, T. A. Freeney, S. R. Sharma, Rajiv S. Mishra

Materials Science and Engineering Faculty Research & Creative Works

Effect of process parameters on friction stir spot welding (FSSW) of 5052 Al alloy has been evaluated. a plunge type FSSW machine was used for this study. Sheet thicknesses of 1 and 1.6mm were used. the tool rotation rate was varied between 1000 and 3000 rpm. the tool plunge rate and dwell time was varied to give weld cycle of 1-4 seconds. Shear tests were performed in 2 sheet and 3 sheet configurations to determine the influence of processing parameters on the mechanical properties of lap joint FSSWs. Higher joint strengths were observed at lower tool rotation rates. Copyright © …

Cracking Of Martensitic Alloy Ep-823 Under Controlled Potential, Ajit K. Roy, M. K. Hossain

Mechanical Engineering Faculty Research

The susceptibility of martensitic Alloy EP-823 to stress corrosion cracking was evaluated with and without an applied cathodic potential using the slow-strain-rate (SSR) testing technique. The magnitude of the applied potential was based on the corrosion potential determined by cyclic polarization. The cracking susceptibility in an acidic environment at different temperatures was expressed in terms of the true failure stress (ơ_f), time to failure (TTF), and ductility parameters, including percent elongation (%El) and percent reduction in area (%RA). The data indicate that the magnitudes of ơ_r, TTF, %El, and %RA were reduced due to cathodic charging. …

Corrosion Mechanisms And Kinetics Of Steels In Lead-Bismuth Eutectic: Quaterly Report, Allen L. Johnson, John Farley

Transmutation Sciences Materials (TRP)

A large number of studies of corroded samples were conducted using SEM, XPS, probe, and the TEM. Samples from the DELTA loop at LANL and from other sources were examined. Also, the investigation of 316 class stainless steel in LBE is continuing.

Corroded samples of D-9 steel have been in the process of being studies, which is a variant of 316 stainless steel that is optimized for resistance to swelling. The D-9 samples are notable for the process in which a localized failure of the protective oxide layer becomes widespread corrosion. The research group is examining the D-9 samples using …

Effect Of Silicon Content On The Corrosion Resistance And Radiation- Induced Embrittlement Of Materials For Advanced Heavy Liquid Metal Nuclear Systems, Ajit K. Roy

Transmutation Sciences Materials (TRP)

This task is primarily focused on the evaluation of the effect of Si content on the susceptibility of modified 9Cr-1Mo-0.24V steel to stress corrosion cracking (SCC) and localized cracking in both molten lead-bismuth eutectic (LBE) and an aqueous solution of acidic pH.

Further, significant efforts are in progress to characterize the deformation mechanism of modified T91 grade steel as a function of temperature and strain rate. Simultaneously, surface analyses of the tested materials are ongoing using state-of-the-art techniques including scanning electron microscopy (SEM) and transmission electron microscopy (TEM).

Corrosion Barrier Development For Lbe Corrosion Resistance: Quarterly Report (April 2006), Biswajit Das

Transmutation Sciences Materials (TRP)

As reported in the last quarterly report, synthesis of Cr nanowires was found to be problematic in terms of uniform coverage. Hence Ni was identified as the alternative metal to form the nanowires. The purpose of the metal nanowires is to provide structural integrity to the nanoporous alumina, as well as a second defense mechanism against corrosion by oxidizing in case the top alumina layer is compromised. Nickel was selected due to its established electrochemical synthesis procedure. While Ni can provide very good structural integrity to the porous alumina, one potential problem is its higher dissolution rate in LBE. However, …

Development Of Nanostructure Based Corrosion-Barrier Coatings On Steel For Transmutation Applications, Biswajit Das

Transmutation Sciences Materials (TRP)

Advanced transmutation systems require structural materials that are able to withstand high neutron fluxes, high thermal cycling, and high resistance to chemical corrosion. The current candidate materials for such structures are ferritic and ferritic-martensitic steels due to their strong resistance to swelling, good microstructural stability under irradiation, and the retention of adequate ductility at typical reactor operating temperatures.

In parallel, lead bismuth eutectic (LBE) has emerged as a potential spallation target material for efficient production of neutrons, as well as a coolant in the accelerator system. While LBE has excellent properties as a nuclear coolant, it is also highly corrosive …

Interaction Between Metal Fission Products And Triso Coating Materials: A Study Of Chemical Bonding And Interdiffusion: 1st Quarterly Report, 2006, Clemens Heske

Fuels Campaign (TRP)

This project is devoted to an in-depth study of the chemical and electronic impact of metal fission products on the coating layers in TRISO nuclear fuel. In particular, there is a focus on the investigation of Pd, Cs, and Ag and their interface formation with SiC and carbon-based substrates. A variety of surface and near-surface bulk sensitive probes that investigate the occupied and unoccupied electronic states of the substrate and the metal overlayer have been utilized. By a controlled and stepwise deposition of the metal overlayer, it is possible to gain substantial insight into the formation of interfaces and their …

Interaction Between Metal Fission Products And Triso Coating Materials, Clemens Heske

Fuels Campaign (TRP)

In this project the chemical bonding and interface formation of metal fission products with the coating materials used in TRISO fuel particles is investigated. The interface formation of Pd, Cs, and Ag with SiC and pyrolytic carbon is studied in detail. Using the SiC single crystals and TRISO coating materials as substrates, interfaces are prepared under controlled conditions in an ultra-high vacuum environment and are studied with a photoelectron spectroscopy, Auger electron spectroscopy, Inverse Photoemission, X-ray emission spectroscopy, and X-ray absorption spectroscopy. Recent additions to the experimental approach include microscopic techniques (Transmission Electron Microscopy, Scanning Tunneling Microscopy, Atomic Force Microscopy) …