Metallurgy Commons^™

Synthesis Of Fuel Cell Membrane: Copolymerization Of Styrene On Etfe Film By Grafted Pre-Irradiation, Yohan Yohan, Rifai M. Nur, Lilik Hendrajaya, E. S. Siradj

Makara Journal of Technology

Synthesis of Fuel Cell Membrane: Copolymerization of Styrene on ETFE Film by Grafted pre-Irradiation. Preirradiation Grafting styrene monomer on ETFE film has been prepared. Research has been performed by γ-ray radiation at various total dose from 2.5 – 12.5 kGy and various dose rate from 1.3 – 1.9 kGy/hour. Irradiated copolymer is then grafted by styrene monomer in various solvent: ethanol, 2-propanol, and toluene, various concentration from 20 – 70% volume, various temperature from 50 – 90oC, and various grafting time from 2 – 12 hours. The results showed that percent of grafting is increase with increase of total dose …

Design Of Product Placement Layout In Retail Shop Using Market Basket Analysis, Isti Surjandari, Annury Citra Seruni

Makara Journal of Technology

Retailing is an industry with high level of competition. It is a customer-based industry which depends on how it could be aware of what the customers’ needs and requirements are. One technique most used in supermarkets is the mix merchandise. The purpose of this paper is to identify associated products, which then grouped in mix merchandise with the use of market basket analysis. This association between products then will be applied in the design layout of the product in the supermarket. The process of identifying the related products bought together in one transaction is done by using data mining technique. …

Production Hydrogen And Nanocarbon Via Methane Decomposition Using Ni-Based Catalysts. Effect Of Acidity And Catalyst Diameter, Widodo W. Purwanto, M. Nasikin, E. Saputra, L. Song

Makara Journal of Technology

Objectives of this research are mainly to study impacts of acidity strength (by varying amount of precipitant and loading Al-Si) and the effect of nickel particle size (by varying calcinations temperature) on decomposition reaction performances. In this research, high-nickel-loaded catalyst is prepared with two methods. Ni-Cu/Al catalysts were prepared with co-precipitation method. While the Ni-Cu/Al-Si catalyst were prepared by combined co-precipitation and sol-gel method. The direct cracking of methane was performed in 8mm quartz fixed bed reactor at atmospheric pressure and 500-700°C. The main results showed that the Al content of catalyst increases with the increasing amount of precipitant. The …

Design And Implementation Of 1-2 Ghz Stepped Frequency Gpr For Buried Metal Detection, Joko Suryana, Andriyan B. Suksmono, Tati R. Mengko

Makara Journal of Technology

Design and Implementation of 1-2 GHz Stepped Frequency GPR for Buried Metal Detection. In this paper, we describe the design and realization steps of 1 – 2 GHz SFGPR (Stepped Frequency Ground Penetrating Radar) transceiver for metal detection under the ground. Before using prototyped GPR for detecting the metal under the ground, several of calibration processes must be performed, namely phase calibration and monocycle pulse waveform calibration. After completing the calibrations, this prototyped GPR would be ready for detecting a hidden object such as a metal plate 5 cm under the ground in our small test range size 25 cm …

Simultaneous Treatment Of Organic (Phenol) And Heavy Metal (Cr6+ Or Pt4+) Wastes Over Tio2, Zno-Tio2 And Cds-Tio2 Photocatalysts, Slamet Slamet, R. Arbianti, Daryanto Daryanto

Makara Journal of Technology

Simultaneous Treatment of Organic (Phenol) and Heavy Metal (Cr6+ or Pt4+) Wastes over TiO2, ZnO-TiO2 and CdS-TiO2 Photocatalysts. Treatment of heavy metal (Cr6+ and Pt4+) and organic (phenol) wastes has been studied using the relatively new method, i.e. simultaneous photocatalytic process over TiO2 photocatalysts in the batch photoreactor. Following the photocatalytic reduction of the heavy metal wastes, recovery of Cr and Pt was carried out by precipitation and leaching method, respectively. The experimental results show that in the simultaneous photocatalytic system, there is a synergism effect between the photocatalytic reduction of heavy metal waste (Cr6+ or Pt4+) and the oxidation …

Design Of Generating Dual Frequency Operation For Triangular Microstrip Antenna Using Electromagnetic Coupling, Indra Surjati, Eko Tjipto Rahardjo, Djoko Hartanto

Makara Journal of Technology

Design of Generating Dual Frequency Operation for Triangular Microstrip Antenna Using Electromagnetic Coupling. A new design is proposed in this paper by applying a pair of slits using a microstrip feed line. Therefore the microstrip line feeding system is electromagnetically coupled to the patch. The antenna works at two different frequencies in the range from 2 GHz to 4 GHz (S band frequency). The results of the simulation shows that the dual frequency operation can be created when the slit width is 1 mm and the height of the slits ranges from 10 mm to 14 mm with inter slit …

Development Of Low Frequency Vibration Method Of Direct-Write Deposition Relevant To Layer Manufacturing Application, Susilo Adi Widyanto, Alva Edy Tontowi, Jamasri Jamasri, Heru Santosa Budi Rochardjo

Makara Journal of Technology

The research of deposition process is the first step in development process of multi materials selective laser sintering. The deposition process enables to settle multi materials powder in horizontal formation on one layer. In this research we use low frequency (70 - 200Hz) to vibrate a hopper nozzle in which powder is settled. The research method consists of two steps, the first step is to determine flow-ability parameters and the second is to join flow ability parameter with other parameters such that the line width can be controlled. The results show that the line width depends on uniformity of particle …

Sub-Surface Corrosion Research On Rock Bolt System, Perforated Ss Sheets And Steel Sets For The Yucca Mountain Repository — Quarterly Technical Report No. 5, Dhanesh Chandra, Jaak J.K. Daemen

Publications (YM)

This report encompasses the work done for this third quarter, 2005, in accordance to cooperative agreement of University of Nevada system for the Task 019 “Subsurface Corrosion Research on Rock Bolt System, Perforated SS Sheets and Steel Sets for the Yucca Mountain Repository”, the overall objective of which is to conduct corrosion research and predict the durability of rock-bolts and other underground metallic roof supports. We have started oxidation tests using Thermogravimetric Analyzer (TGA), and Potentiodynamic tests to determine the corrosion rates of rock bolts, other support materials including bench mark materials. In this quarter, we have also performed (1) …

Journal Of Materials Engineering And Performance: Editorial, C. Suryanarayana, Leon L. Shaw, Rajiv S. Mishra

Materials Science and Engineering Faculty Research & Creative Works

No abstract provided.

Modeling, Fabrication, And Optimization Of Niobium Cavities Final Phase: Final Report, Robert A. Schill Jr., Mohamed Trabia, William Culbreth

Transmutation Sciences Materials (TRP)

This final report provides the activities and accomplishments of Modeling, Fabrication, and Optimization of Niobium Cavities – Final Phase. The fluid flow experiments for the etching of the superconducting cavity walls and baffle designs of phase II of the three phases has been completed leading to a MS thesis in December of 2003. Designing the experimental setup of secondary electron emission was well underway in early summer of 2003 when funding was made available for this portion of the study. By March 2004, many of the components of the experimental study reached UNLV with some assembly accomplished. The first secondary …

Use Of Positron Annihilation Spectroscopy For Stress-Strain Measurements: Quarterly Progress Report (March – May 2005), Ajit K. Roy

Transmutation Sciences Materials (TRP)

Accomplishments:

● Analyses of defects (dislocations) in martensitic Alloy EP-823, cold-reduced to different levels, have been performed by using transmission electron microscopy. The dislocation density has been related to the degree of cold-reduction and residual stress in terms of a line-shape parameter determined by the positron annihilation spectroscopy (PAS).

● Additional PAS measurements are ongoing on tensile, welded and cold-worked specimens of Alloys EP-823 and HT-9 at the Idaho Accelerator Center of ISU. Both Subhra and Silpa are involved in these measurements.

● Silpa is performing neutron diffraction (ND) measurements at the Atomic Energy of Canada Limited (AECL), Chalk River …

Sub-Surface Corrosion Research On Rock Bolt System, Perforated Ss Sheets And Steel Sets For The Yucca Mountain Repository — Quarterly Technical Report No. 4, Dhanesh Chandra, Jaak J.K. Daemen

Publications (YM)

This report encompasses the work done for this third quarter, 2005, in accordance to cooperative agreement of University of Nevada system for the Task 019 “Subsurface Corrosion Research on Rock Bolt System, Perforated SS Sheets and Steel Sets for the Yucca Mountain Repository”, the overall objective of which is to conduct corrosion research and predict the durability of rock-bolts and other underground metallic roof supports. We have started oxidation tests using Thermogravimetric Analyzer (TGA), and Potentiodynamic tests to determine the corrosion rates of rock bolts, other support materials including bench mark materials. In this quarter, we have also performed hydrogen …

Effect Of Silicon Content On The Corrosion Resistance And Radiation-Induced Embrittlement Of Materials For Advanced Heavy Liquid Metal Nuclear Systems: Quarterly Progress Report (February – April 2005), Ajit K. Roy

Transmutation Sciences Materials (TRP)

This proposal is intended to study the effect of Si content not only on the corrosion resistance but also on the radiation-induced embrittlement of martensitic stainless steels. The susceptibility of these alloys with different Si content to stress corrosion cracking, general corrosion and localized corrosion will be evaluated in the molten LBE and aqueous environments of different pH values using state-of-the-art testing techniques. Testing in the aqueous media is intended to develop baseline data for comparison purpose. Radiation-induced embrittlement of these alloys will initially be studied by irradiating the test specimens with bremmstrahlung gamma radiation from 20-40 MeV electron beams …

Use Of Positron Annihilation Spectroscopy For Stress-Strain Measurements: Quarterly Progress Report (December 01, 2004 – February 28, 2005), Ajit K. Roy

Transmutation Sciences Materials (TRP)

The purpose of this collaborative research project involving the University of Nevada Las Vegas (UNLV), the Idaho State University (ISU), and the Los Alamos National Laboratory (LANL) is to evaluate the feasibility of determining residual stresses in cold-worked, plastically-deformed (bent), and welded materials using a nondestructive method based on positron annihilation spectroscopy (PAS). This technique uses γ-rays from a small MeV electron Linac to generate positrons inside the sample via pair production. This method is known to have capabilities of characterizing defects in thick specimens that could not be accomplished by conventional positron technique or other nondestructive methods. The data …

Effect Of Silicon Content On The Corrosion Resistance And Radiation-Induced Embrittlement Of Materials For Advanced Heavy Liquid Metal Nuclear Systems: Quarterly Progress Report (November 2004 – January 2005), Ajit K. Roy

Transmutation Sciences Materials (TRP)

This proposal is intended to study the effect of Si content not only on the corrosion resistance but also on the radiation-induced embrittlement of martensitic stainless steels. The susceptibility of these alloys with different Si content to stress corrosion cracking, general corrosion and localized corrosion will be evaluated in the molten LBE and aqueous environments of different pH values using state-of-the-art testing techniques. Testing in the aqueous media is intended to develop baseline data for comparison purpose. Radiation-induced embrittlement of these alloys will initially be studied by irradiating the test specimens with bremmstrahlung gamma radiation from 20-40 MeV electron beams …

Modeling, Fabrication, And Optimization Of Niobium Cavities: Phase Iii Fourth Quarterly Report, Robert A. Schill Jr., Mohamed Trabia, William Culbreth

Transmutation Sciences Materials (TRP)

Niobium cavities are important parts of the integrated NC/SC high-power linacs. Over the years, researchers in several countries have tested various cavity shapes. They concluded that elliptically shaped cells are the most appropriate shape for niobium superconducting cavities. The surface preparation can significantly affect the secondary electron emission yields. Such yields are used in design codes. Current codes use values obtained from niobium samples cleaned by a different means at temperatures other than the operating temperature. Secondary electron emission studies on LANL surface-cleaned niobium are conducted with preliminary data presented in this report at room temperature. Soon studies will be …

Sub-Surface Corrosion Research On Rock Bolt System, Perforated Ss Sheets And Steel Sets For The Yucca Mountain Repository — Quarterly Technical Report No. 3, Dhanesh Chandra, Jaak J.K. Daemen

Publications (YM)

This report encompasses the work done for third quarter in accordance to cooperative agreement of UCCSN for the Task 019 “Subsurface Corrosion Research on Rock Bolt System, Perforated SS Sheets and Steel Sets for the Yucca Mountain Repository”, the objective of which was proposed earlier, to conduct corrosion research and predict the durability of rockbolts and other underground metallic roof supports. We have recently started working on oxidation tests using Thermogravimetric Analyzer (TGA), stress corrosion cracking/hydrogen embrittlement studies on rock bolts, other support materials including bench mark materials. In this quarterly report we will discuss “Dry” oxidation of steels and …

3d Modelling With Linear Approaches Using Geometric Primitives, Mochammad Zuliansyah

Makara Journal of Technology

In this paper, we study linear approaches for 3D model acquisition from non-calibrated images. First, the intrinsic and extrinsic camera calibration is taken into consideration. In particular, we study the use of a specific calibration primitive: the parallelepiped. Parallelepipeds are frequently present in man-made environments and naturally encode the affine structure of the scene. Any information about their euclidean structure (angles or ratios of edge lengths), possibly combined with information about camera parameters is useful to obtain the euclidean reconstruction. We propose an elegant formalism to incorporate such information, in which camera parameters are dual to parallelepiped parameters, i.e. any …

Tensile Properties Of Martensitic Stainless Steels At Elevated Temperatures, Ajit K. Roy, Srinivasarao R. Kukatla, Bhagath Yarlagadda, V. N. Potluri, Martin Lewis, Brendan O'Toole

Mechanical Engineering Faculty Research

Tensile properties of quenched and tempered martensitic alloys EP-823, HT-9, and 422 were evaluated at temperatures ranging from ambient to 600 °C as a function of three different tempering times. The results indicated that the yield strength, ultimate tensile strength, and the failure strength were gradually reduced with increasing temperature. The ductility parameters were enhanced at elevated temperatures due to increased plastic flow. However, the tempering time did not significantly influence these properties. The evaluation of the fracture surfaces by scanning electron microscopy revealed reduced cracking and dimpled microstructures, indicating enhanced ductility at higher testing temperatures.

Residual Stress Characterization In Structural Materials By Destructive And Nondestructive Techniques, Ajit K. Roy, Anand Venkatesh, Vikram Marthandam, Satish Dronavalli, Douglas P. Wells, Ronald Rogge

Mechanical Engineering Faculty Research

Transmutation of nuclear waste is currently being considered to transform long-lived isotopes to species with relatively short half-lives and reduced radioactivity through capture and decay of minor actinides and fission products. This process is intended for geologic disposal of spent nuclear fuels for shorter durations in the proposed Yucca Mountain repository. The molten lead-bismuth-eutectic will be used as a target and coolant during transmutation, which will be contained in a subsystem vessel made from materials such as austenitic (304L) and martensitic (EP-823 and HT-9) stainless steels. The structural materials used in this vessel will be subjected to welding operations and …

Fundamental And Applied Experimental Investigations Of Corrosion Of Steel By Lbe Under Controlled Conditions: Kinetics, Chemistry, Morphology, And Surface Preparation: Quarterly Report (January 2005-April 2005), Allen L. Johnson, John Farley, Dale L. Perry

Transmutation Sciences Materials (TRP)

This project has four components:

• The fabrication of a materials test apparatus with unique capabilities,
• Comparative studies of steel corrosion under gas phase conditions comparable to the Lead Bismuth Eutectic (LBE) oxygen control conditions,
• Isotope labeling studies, and
• Collaborative efforts with other workers in the field.

Summary of accomplishments:

• Started occupation of the High Temperature Materials Experimental Facility.
• Presented a paper at the meeting of the American Chemical Society in San Diego in March 13-17.
• Currently reviving the ion beam for implantation experiments.
• Currently analyzing 38 steel samples from the DELTA loop from LANL.

Synthesis Dibenzyl Terephthalate Through Depolimerization Of Poly (Ethylene Terephthalate) As Alternative Of Waste Plastics Recycling, Suwardi Suwardi, Crys Fajar Partana, Agus Salim, Dyah Anitasari

Makara Journal of Technology

Synthesis Dibenzyl Terephthalate Through Depolimerization of Poly(ethylene terephthalate) as Alternative of Waste Plastics Recycling. Synthesis dibenzyl terephathalate were done through PET degradation by refluxing in benzyl alcohol at 145oC temperature for 20, 24, and 28 hours in the presence of zinc acetate catalyst. The result of degradation was purified by recristalization in methanol and then melting point (mp), FTIR, 1H NMR spectra, and TLC spot were determined. The melting point of product degradation for 28 hours was 98-99 oC. Based FTIR spectra known that compunds of product degradation have OH, C=O, C-O, CH, monosubstituted benzene, disubstituted benzene groups, while on …

Dipole Magnetization Effect To Kerosene Characteristics, Mochamad Chalid, Nelson Saksono, Adiwar Adiwar, Nono Darsono

Makara Journal of Technology

Dipole Magnetization Effect to Kerosene Characteristics. Investigation of kerosene characteristics has been done by ex-situ dipole magnetization. The results show that magnetization technique can be able to influence kerosene characteristics. Polarity and viscosity of the kerosene are observed by measuring refractive index and viscosity. An hour of 4330 Gauss flux magnetic will increase refractive index from 1.447 to 1.449 and decrease the viscosity from 1.278 to 1.256. Those changing support de-clustering occurrence and polarity increment of kerosene molecule. Gas chromatography and infrared result show that those changing do not alter kerosene structure and composition.

Study Of 2d And 3d Optical Beam Induced Voltage Imaging Using Photoresistor Sensor, Warsito Warsito, Sri Wahyu Suciyati, Susi Harnani, Akhmad Dzakwan

Makara Journal of Technology

Study of 2D and 3D Optical Beam Induced Voltage Imaging Using Photoresistor Sensor. This article shows a method to study OBIV (optical beam induced voltage) imagerie system, that usually employ a laser scanning microscopy system. The OBIV imagerie system developed use a photoresistor sensor as a sample and simultaneously it can be used for analyzing its inhomogeneity response. Resolution of the system is still low, about 350μm due to high value of incident light diameter. The results inform that photoresistor sensors gave an optimum response if the incident light hits the center of sensible zone.

Flexi Radio Base Station (Rbs) Performance Analysis Of Voice And Trafic On Kota 2 Jakarta Barat Base Station Control (Bsc), Mushfar Ferdian, Fitri Yuli Zulkifli

Makara Journal of Technology

Flexi Radio Base Station (RBS) Performance Analysis of Voice and Trafic on Kota 2 Jakarta Barat Base Station Control (BSC). The CDMA 2000 technology uses circuit switch method to handle voice traffic and packet switch method to handle data traffic between the user and RBS (Radio Base Station). These two parameters can be used to measure performance of the network generally, so it is necessary to optimize them. This paper analyze the performance of RBS by measuring its parameters such as set up failure ratio, drop ratio, and occupancy. Furthermore, the traffic increment is calculated too in order to provide …

Water Quality Of Rivers And Ponds On Dki Jakarta, Diana Hendrawan

Makara Journal of Technology

Water Quality of Rivers and Ponds on DKI Jakarta. Thirteen big rivers, some small rivers, and 40 ponds spread over districts at Jakarta city are potential to support human being life. As the population is growing and the usage of stream water is increasing, the condition and quality of rivers and ponds are changing. Crowd housing can affect rivers and ponds pollution, as the people awareness about clean and healthy environment is less. Stream water pollution assessment can be done by counting the effect of pollutant to life of stream water organisms. This assessment unit could be classified into physics, …

Time Domain Characterization Of 1-2 Ghz Circular-Ended Bowtie Antenna Using Normalizad Impulse Response, Joko Suryana, Andriyan B. Suksmono, Tati R. Mengko

Makara Journal of Technology

Time Domain Characterization of 1-2 GHz Circular-ended Bowtie Antenna Using Normalizad Impulse Response. Frequency domain analysis is a powerful and compact tool for characterizing the antenna parameters such as gain, radiation pattern and the impedance as a function of frequency. However, if time or space is a major concern, such as in the GPR appication, the time domain analysis would be a very important tool due to their unique capability for determining the echo delay and range profile of target image. In this paper, we will describe the classical theory of system characterization in time domain, and then also propose …

Theoretical Modeling Of Protective Oxide Layer Growth In Non-Isothermal Lead-Alloys Coolant Systems: Quarterly Progress Report (01/01/05- 03/31/05), Yitung Chen

Transmutation Sciences Materials (TRP)

The goal of the proposed research project is to provide basic understanding of the protective oxide layer behaviors and to develop oxide layer growth models of steels in non-isothermal lead-alloys (lead or lead-bismuth eutectic) coolant systems. It is widely recognized that the corrosiveness of the lead-alloys is a critical obstacle and challenge for which it can be safely used or applied in the nuclear coolant systems. Active oxygen control technique can promote the formation of the “self-healing” oxide films on the structural material surface, drastically reducing steel corrosion and coolant contamination. Many experiments of steels exposed to flowing lead-alloys have …

An Investigation Of A Simplified Gouging Model, Gregory S. Rickerd

Theses and Dissertations

Gouging is a type of structural failure that becomes important when two metals slide against each other at velocities in the range of 1.5 kilometers per second. A computer model has previously been used to model the development of gouging at the Holloman High Speed Test Track. This model has not been experimentally verified to be correct, due to the complexity of the model. This research develops a simplified model that can be experimentally verified. The computer program utilized in this research was studied to determine the most appropriate options to use in simulations. This was accomplished by modeling a …

Effect Of Silicon Content On The Corrosion Resistance And Radiation-Induced Embrittlement Of Materials For Advanced Heavy Liquid Metal Nuclear Systems: Quarterly Progress Report (August 2004 – October 2004), Ajit K. Roy

Transmutation Sciences Materials (TRP)

The purpose of this collaborative research project involving the University of Nevada Las Vegas (UNLV), Los Alamos National Laboratory (LANL) and Idaho State University (ISU) is to evaluate the effect of silicon (Si) content on the corrosion behavior and radiation-induced embrittlement of martensitic stainless steels having chemical compositions similar to that of the modified 9Cr-1Mo steel. Recent studies at LANL involving Alloy EP-823 of different Si content have demonstrated that increased Si content in this alloy may enhance the corrosion resistance in molten lead-bismutheutectic (LBE). Since very little data exists in the open literature on the beneficial effect of Si …