Metallurgy Commons^™

In-Situ Defect Detection Using Acoustic Vibration Monitoring For Additive Manufacturing Processes, Ali Harake

Master's Theses

The world of additive manufacturing revolves around speed and repeatability. Inherently, the process of 3D printing is plagued with variability that fluctuates with every material and parameter modification. Without proper qualification standards, processes can never become stable enough to produce parts that may be used in aerospace, medical, and construction industries. These industries rely on high quality metrics in order to protect the lives of those who may benefit from them. To establish trust in a process, all points of variation must be controlled and accounted for every part produced. In instances where even the best process controls are enacted, …

Minimizing Leakage In Thin Walled Structures Printed Through Selective Laser Melting, Andrew Spencer Yap

Master's Theses

In this project, the scan strategy of selective laser melting (SLM) for thin walled structures was investigated by changing laser parameters and tool path. Producing thin walled structures is difficult due to defects such as warpage and porosity. A layer on the SLM 125 consists of hatch volume, fill contours, and borders, however, for thin walls, hatch volume can become unavailable, resulting in a solely border/fill contour laser tool path.

Three central composite designs (CCD) were created to optimize the laser parameters of borders to minimize leakage rate and porosity. The two factors changed were border laser power and scanning …

An Evaluation Of Ultrasonic Shot Peening And Abrasive Flow Machining As Surface Finishing Processes For Selective Laser Melted 316l, Rhys Gilmore

Master's Theses

Additive Manufacturing, and specifically powder bed fusion processes, have advanced rapidly in recent years. Selective Laser Melting in particular has been adopted in a variety of industries from biomedical to aerospace because of its capability to produce complex components with numerous alloys, including stainless steels, nickel superalloys, and titanium alloys. Post-processing is required to treat or solve metallurgical issues such as porosity, residual stresses, and surface roughness. Because of the geometric complexity of SLM produced parts, the reduction of surface roughness with conventional processing has proven especially challenging. In this Thesis, two processes, abrasive flow machining and ultrasonic shot peening, …

Preliminary Investigations Into Selective Laser Melting, David Takeo Otsu

Master's Theses

Selective laser melting is a promising metallic additive manufacturing process with many potential applications in a variety of industries. Through a gracious donation made by Lawrence Livermore National Laboratory, California Polytechnic State University received and installed an SLM 125 HL selective laser melting machine in February 2017. As part of the initial setup effort, a preliminary machine verification study was conducted to evaluate the general print quality of the machine with default parameter settings. Coincidentally, the as-printed microstructure of SLM components was evaluated through nil strength fracture surface examination, an alternative to conventional polish-and-etch metallography. A diverse set of components …

Superalloy Metallurgy A Gleeble Study Of Environmental Fracture In Inconel 601, Alan C. Demmons

Master's Theses

At temperatures above 0.5 Tm and in aggressive atmospheres predicting alloy performance is particularly challenging. Nickel alloys used in regimes where microstructure and properties are altered dynamically present unique requirements. Exposure may alter properties with unexpected early failure. The Gleeble is a valuable tool for investigation and simulation of thermo-mechanical properties of an alloy in various regimes up to the threshold of melting. In this study, four regimes of temperature and strain rate were simulated in an argon atmosphere to both investigate and document normal and abnormal failure modes. Commercial Inconel 601 was tested in selected regimes and in two …

Influence Of Grain Size And Widmanstätten Colonies On Variability Of Tensile Properties Of Forged Ti-6al-4v, Blake T. Gaspar

Master's Theses

When testing forgings for specifications, it was found that some parts did not meet the requirements for mechanical properties. This triggered an investigation into two of the parts from the lot that did not meet specification. The ultimate reason for failure was due to lower than necessary yield strength and ultimate tensile strength values, as well as unwanted variability between regions of the part. Therefore, samples of the regions were tensile tested to determine the differences that existed in yield strength, ultimate tensile strength, and elongation. After tensile testing, quantitative metallography and fractography were conducted to identify aspects of the …

Analysis Of Bimetallic Adhesion And Interfacial Toughness Of Kinetic Metallization Coatings, Alec D. Guraydin

Master's Theses

Due to their ability to confer enhanced surface properties without compromising the properties of the substrate, coatings have become ubiquitous in heavy industrial applications for corrosion, wear, and thermal protection, among others. Kinetic Metallization (KM), a solid-state impact consolidation and coating process, is well-suited for depositing industrial coatings due to its versatility, low substrate heat input, and low cost. The ability of KM coatings to adhere to the substrate is determined by the quality of the interface. The purpose of this study is to develop a model to predict the interfacial quality of KM coatings using known coating and substrate …

An Experimentally Generated Constitutive Model For Peak Stress (Σ_Peak) In Compression Samples, Kevin Mathew Lopez Galang

Master's Theses

The hot working behavior of AISI 1018 steel was studied by hot-compression deformation tests on the Gleeble 1500 thermo-mechanical simulator at true strain values of -0.143 and -0.405, true strain rate values of 0.01 and 0.1, and working temperatures of 900^°C and 1000°C. The tests show that a lower working temperature and lower true strain value results in a greater maximum compressive force. The apparent activation energy Q_app was calculated by using the Zener-Hollomon parameter combined with the low stress law. Q_{app ­}was calculated to be 311 kJ mol^-1 K^-1.

Bacterial Growth On Metal And Non-Metal Surfaces In A Static Bioreactor, Rolan Yuk Loong Liong

Master's Theses

Research was conducted to observe bacterial growth on the surface of metals in a static bioreactor. Metal and non-metal samples were subjected to bacterial exposure (1 day and 9 days). The metal samples were surface treated prior to bacterial exposure. The microstructures of the surface treated samples were analyzed by optical microscopy. After exposure, the microstructures of the samples were analyzed by scanning electron microscopy (SEM). The analysis suggested that microbial attachment on the surface was related to the underlying microstructure of steel. The preferential attachment of microbes could potentially be influenced by cathodic and anodic regions created by the …

Investigation Of Astm E 238 Bearing Pin Properties For Various Aerospace Alloys, Trevor J. Lee

Master's Theses

Aircraft are often designed with numbers determined by testing in a lab, rather than by repeatedly building prototypes. These lab tests conform to testing specifications so that the numbers can be compared between manufacturers, suppliers, and lab technicians. One such specification is ASTM specification E238 – 84(08), and it is used to determine important properties of a bearing pin joint like hinges, bolt holes, and rivet joints. The properties determined from this fastener-through-plate method are bearing strength, bearing yield strength, and bearing stiffness.

Adhering to the methods outlined in ASTM E238, a study was performed, looking at the effects that …

Effect Of Oxidation On Weld Strengthof Dissimilar Resistance Weld Interface Between 304 Stainless Steeland Near Equiatomic Austenitic Nitinol Guide Wire, Matthew Rudow

Master's Theses

Abbott Vascular encountered strength and variability issues when attempting to resistively weld 304 Stainless Steel to equiatomic Nitinol. Initial observations suggested that passivation layer (Cr₂O₃, TiO₂) formation affected the weld interface. One hundred 304 Stainless Steel/Nitinol pairs were allowed to oxidize in air at room temperature for allowed periods of time (.1, 1, 3, 5, 7, 12, 16, 24, 168, and 336 hours). Each pair was welded resistively with constant current. A Miyachi/Unitek Advanced Data Analysis Monitor (ADAM) recorded the peak resistance at the instance the weld was made. Resistances were compared to Instron …

A Quantitative Study Of The Weldability Of Inconel 718 Using Gleeble And Varestraint Test Methods, Sean Quigley

Master's Theses

Nickel super alloy Inconel 718 was tested and compared to Haynes 230 using Gleeble and Varestraint mechanical test methods. Hot cracking susceptibility was examined in either alloy using a sub-scale Varestraint test method at 5 augmented strain levels: 0.25%, 05.%, 1%, 2%, and 4%. Maximum crack length, total crack length, and number of cracks were measured for each strain level. Gleeble hot ductility on-heating and on-cooling tests were performed on both alloys. Inconel 718 was tested on-heating at target temperatures of 1600˚F, 2000˚F, 2100˚F, 2200˚F, and on cooling at 1600˚F, 1700˚F, 1800˚F, 1900˚F, and 2100˚F. Haynes 230 was tested on-heating …

Design, Fabrication, And Characterization Of A Thin-Film Nickel-Titanium Shape Memory Alloy Diaphragm For Use In Micro-Electro-Mechanical Systems, Brian Joel Alvarez

Master's Theses

Previous work done at Cal Poly has shown that thin-film nickel-titanium (NiTi) can be easily sputtered onto silicon wafers and annealed to create a crystallized shape memory alloy (SMA) film. Initial work on creating devices yielded cantilevers that were highly warped due to thin-film stress created during the sputtering process. The objective of this work was to create a thin-film NiTi SMA device that could be better characterized. A membrane was selected due to the simplicity of fabrication and testing which would also oppose the thin-film stress due to the increase in attachment points to the substrate.

Silicon wafers were …

Effect Of Au Content On Microstructural Evolution Of Snagcu Solder Joints That Undergo Isothermal Aging And Reliability Testing, Patrick J. Hyland

Master's Theses

Electronics, especially, printed circuit boards (PCBs) are a widespread technology. Metal coatings or “surface finishes” are often added to PCB board pads and component leads during manufacturing to improve their performance. Electroplated nickel/gold over copper is a popular surface finish for printed circuit boards and component leads. The presence of gold in solder joints, however, is known to have detrimental effects referred to as gold embrittlement. It is generally understood that tin-lead solder joints with less than 3 weight percent (wt%) of gold will not experience reliability issues. The acceptable level of gold in lead-free solder joints, however, is less …

Characterization Of Inconel 718: Using The Gleeble And Varestraint Testing Methods To Determine The Weldability Of Inconel 718, Nathaniel Oscar Knock

Master's Theses

Nickel based superalloys were developed to withstand the severe thermal and mechanical environment associated with rocket propulsion systems and jet engines. In many alloy systems the strength of a component rapidly deteriorates as the operating temperature increases. Nickel based superalloys, however, retain strength over a range of temperatures which includes the operating range for many propulsion systems. This improved performance is accomplished by a combination of solid-solution strengthening, precipitation strengthening and grain-boundary strengthening. Furthermore, super-alloy systems are designed for ease of fabrication, to include machining, welding and heat treating. Inconel 718 was developed to overcome problems with post-weld cracking that …

The Effects Of Applied Strain And Heat Treatment On The Properties Of Niti Wire During Shape Setting, Frank Zapoticla

Master's Theses

NiTi components are commonly subjected to thermo-mechanical heat treatments during production and fabrication. This study investigates the effects of applied strain of 0-10% and heat treatments of 300-600ºC for times of 2-30 minutes during shape-setting of Ti–50.8 at% Ni wire with a nominal diameter of 0.495 mm and an initial transition temperature, Af, of 12ºC. Strain was applied prior to heat treatments by coiling NiTi wire, essentially producing coiled springs, around different diameter steel mandrels to obtain different strain levels. The samples of NiTi wire under applied strain were heat treated in a salt bath, followed by a rapid quench. …

Shielding Effectiveness Of Superalloy, Aluminum, And Mumetal Shielding Tapes, Cindy Suit Cheung

Master's Theses

Using MIL-HDBK-419A, MATLAB and Nomographs, Shielding Effectiveness for the Magnetic Field, Electric Field, and Plane Wave were calculated over a frequency range from 10 Hz to 1 GHz. The three shielding tapes used included superalloy, aluminum, and mumetal. Calculations for Shielding Effectiveness involve the computation of Absorption Loss, Reflection Loss, and Re-Reflection Correction Factor. From the outcome of the calculations, it was suitable to conclude that all three metals fulfill the 40 dB Shielding Effectiveness requirements for SGEMP fields for frequencies greater or equal to 1 MHz. Accordingly, all three shielding tapes provide at least 40 dB of shielding to …