Metallurgy Commons^™

Use Of Electrochemical Techniques And Statistical Analysis To Investigate The Pitting Probability Of Copper, Sina Matin

Electronic Thesis and Dissertation Repository

The development of a safe permanent disposal plan is essential for the long-term disposal of used fuel bundles. Nuclear Waste Management Organization (NWMO) has been investigating the deep geologic disposal of nuclear waste which offers the optimum passive safety system with a negligible probability of release of radionuclides into the environment.

The proposed used fuel containers (UFC) for the permanent disposal of high-level nuclear waste in Canada is comprised of a carbon steel vessel coated with a 3 mm corrosion-resistant copper layer deposited using a combination of electrodeposition and cold spray deposition. Although copper is often considered to be thermodynamically …

Near-Ir Laser Ablation Of Simulated Radiologically Contaminated Oxides On Carbon Steel Feeder Pipes, Thao Viet Do

Electronic Thesis and Dissertation Repository

As nuclear power plants age and retire from service, many countries face significant challenges concerning the safe long-term storage and disposal of large volumes of low and intermediate level radioactive wastes (L&ILW). The volumes of metallic waste are of particular concern, as when metal corrodes it produces hydrogen that could lead to pressure build-up in interim storage and disposal. In Canada, a significant fraction of the metallic wastes for Canada Deuterium Uranium (CANDU) nuclear reactors are out-of-core reactor components, such as carbon steel (CS) feeder pipes. The radioactive contamination is expected to be largely confined to the surface oxide layers …

Effect Of Ion Implantation On The Mechanical Properties Of The Grain And Grain Boundary Regions Of Inconel X750, Maisaa Nezar Tawfeeq

Electronic Thesis and Dissertation Repository

Annulus gas spacers in CANada Deuterium Uranium (CANDU) nuclear reactors are made from the heat-treated Inconel X750 Nickel-based alloy. This alloy is designed to have high strength and creep resistance at elevated temperature. Unlike other reactor designs, the CANDU reactor has a high thermal neutron fluence, which results in an enhancement of the radiation damage and the internal production of helium and hydrogen. They are thus susceptible to microstructural instability and mechanical property degradation with time. Studies of ex-service spacers have indicated that they display intergranular embrittlement and lower ultimate tensile strength compared to nonirradiated Inconel X750. The primary degradation …

Study On The Surface Features Of Preg-Robbing Carbonaceous Matter During Oxidation Treatment, Mana Pourdasht

Electronic Thesis and Dissertation Repository

Carbonaceous gold ores have the ability to adsorb gold (I) cyanide from leach solutions during processing. This phenomenon, known as preg-robbing, is responsible for poor recoveries as the carbonaceous materials of the ore compete with activated carbon used during the leaching and adsorption phase of processing. Chemical oxidation of carbonaceous materials by different reagents has been utilized to investigate and compare the mechanism of Au (CN)₂ adsorption onto carbonaceous materials prior to and following the treatment.

The procedure for characterization of the carbonaceous materials (plain and modified) in the sample combines the use of several analytical techniques and test …

Gamma-Radiation Induced Corrosion Of Alloy 800, Mojtaba Momeni

Electronic Thesis and Dissertation Repository

This thesis presents a newly developed mechanism and predictive model for the corrosion of Alloy 800. The Fe-Cr-Ni Alloy (Incoloy 800) is mainly used for steam generator (SG) tubing in CANDU and PWR reactors and is a candidate material for the proposed Canadian Supercritical Water Reactor (SCWR) in which it will be exposed to extreme conditions of high radiation flux and large temperature gradients. The influence of gamma radiation and water chemistry conditions on the corrosion behaviour of Alloy 800 are studied in this work. Ionizing radiation creates reducing (•e_aq^–, •H, •O₂^-) and oxidizing …

Effective Boronizing Process For Age Hardened Inconel 718, Aria Khalili

Electronic Thesis and Dissertation Repository

Boronizing or boriding is a technique to mitigate wear damage in industrial valves made of age-hardenable Inconel^® 718 which is a nickel-based superalloy. Boriding involves immersing the part in a patented boron-based compound and heating over 800 ^oC.

Boriding combined with aging has a detrimental thermal effect and was the subject of this investigation. The effects on hardness, wear and grain size, of boriding and aging separately, subsequently, and simultaneously, were investigated to observe the microstructure and mechanical properties.

The results show that boriding has negligible effect on the grain size and the hardness of the substrate. Besides, …

Application Of 3d Printing Technology In Porous Anode Fabrication For Enhanced Power Output Of Microbial Fuel Cells, Bin Bian

Electronic Thesis and Dissertation Repository

Microbial fuel cells (MFCs) are widely researched for application in wastewater treatment. However, the current anodes used in MFCs often suffer from high fabrication cost and uncontrollable pore sizes. In this thesis, three-dimensional printing technique was utilized to fabricate anodes with different micro pore sizes for MFCs. Copper coating and carbonization were applied to the printed polymer anodes to increase the conductivity and specific surface area. Voltages of MFCs with various anodes were measured as well as other electrochemical tests such as linear sweep voltammetry and electrochemical impedance spectroscopy. 3D copper porous anode produced higher maximum voltages and power densities …

Numerical Modeling Of Solidification Process And Prediction Of Mechanical Properties In Magnesium Alloys, Mehdi Farrokhnejad

Electronic Thesis and Dissertation Repository

A formulation used to simulate the solidification process of magnesium alloys is developed based upon the volume averaged finite volume method on unstructured collocated grids. To derive equations, a non-zero volume fraction gradient has been considered and resulting additional terms are well reasoned. For discretization the most modern approximations for gradient and hessians are used and novelties outlined. Structure-properties correlations are incorporated into the in-house code and the proposed formulation is tested for a wedge-shaped magnesium alloy casting. While the results of this study show a good agreement with the experimental data, it was concluded that a better understanding of …

Micro-Mechanical Assessment Of The Local Plastic Strain Invoked During A Splined Mandrel Flow Forming Operation, Meysam Haghshenas

Electronic Thesis and Dissertation Repository

Splined Mandrel Flow Forming (SMFF) is a metal spinning operation that involves the application of high multiaxial compressive stress states to invoke large plastic flow in the work piece. This allows for essentially one-step fabrication of complex internally-splined shapes. In this research project, the equivalent plastic strain, invoked throughout bcc (1020 steel) and fcc (5052 and 6061 aluminum alloys, pure copper, and 70/30 brass) samples, that were made by SMFF, was measured. The objective of the research were to measure the to obtain data on the effect of microstructure and mechanical parameters on the flow formability of ductile bcc and …

Process-Structure Relationships Of Magnesium Alloys, Arindam Banerjee

Electronic Thesis and Dissertation Repository

This research study characterizes the effects of solidification conditions on the resulting microstructure of an AM60B magnesium alloy during the solidification cycle of the casting. Seventeen control points are chosen from different sections of an instrument panel beam casting and its centerline coordinates are located. These control points locations are then used by Meridian Lightweight Technology Inc. to run a simulation in a MAGMASoft casting software to obtain temperature-time specific data.

An exact analytical solution to the Stefan problem is used to compute the one dimensional heat transfer for a section of the casting and to calculate its temperature distribution …

Investigation Of The Use Of Micro-Mechanical Testing To Analyze The Mechanical Anisotropy Of The Zr-2.5%Nb Pressure Tube Alloy, Richard O. Oviasuyi

Electronic Thesis and Dissertation Repository

Maintaining a safe operation of nuclear power plants is the primary requirement of nuclear power generating organizations worldwide. This necessitates the use of highly effective methods for assessing the mechanical properties of reactor materials and components. This is important since all components located in a nuclear reactor core experience high levels of neutron irradiation which cause defects to be formed in the metals’ crystal structure. The density of these crystal defects increases with increasing exposure to neutrons and cause the crystalline metal to become harder and simultaneously more brittle. This change in mechanical properties is potentially detrimental to the safe …

The Effect Of The Environment On The Corrosion Products And Corrosion Rates On Gas Transmission Pipelines, Brent Sherar

Electronic Thesis and Dissertation Repository

This thesis reports a series of investigations examining external corrosion processes along gas transmission pipelines. TransCanada PipeLines Ltd. (TCPL) has developed six proposed corrosion scenarios to describe external pipeline corrosion, based primarily on corrosion products and corrosion rates (CRs) observed at field sites. The six proposed corrosion scenarios can be divided into two groups: abiotic and biotic. The three abiotic corrosion scenarios are (1) anaerobic corrosion, (2) aerobic corrosion, and (3) anaerobic corrosion turning aerobic; while (4) anaerobic corrosion with microbial effects, (5) aerobic corrosion turning anaerobic with microbial effects, and (6) anaerobic corrosion with microbial effects turning aerobic comprise …