Metallurgy Commons^™

Electropulse Annealing: Phase Composition Of Tial6v4, Vaughn Eckhardt, Ethan Croke, Ian Baker, Russ Taylor

Wetterhahn Science Symposium Posters

Titanium alloy TiAl6V4 is the most ubiquitous titanium alloy used for dental care, aerospace manufacturing, and for high performance vehicles. The material typically undergoes a thermal heat  treatment, but electropulse annealing is another process that involves sending current through the material to heat it up at a quicker rate. The rate of post-annealing cooling is high, and around the material's critical point, its two components, alpha and beta phase, change in relative concentration. After testing multiple current densities and temperatures, in general, as the current density that the sample received during electropulse annealing decreased, both the alpha and beta phases …

High Temperature Creep Deformation Mechanism Of Fe28.2ni18.8mn32.9al14.1cr6 High Entropy Alloy And Its Modified Alloys, Edwin S. Jiang, I. Baker

Dartmouth College Ph.D Dissertations

Fe28.2Ni18.8Mn32.9Al14.1Cr6 eutectic high entropy alloy exhibits a good combination of room-temperature and high temperature properties, including tensile strength, ductility, and corrosion resistance, making it a promising candidate for structural applications in extreme environments. However, the creep deformation behavior of this alloy— and high-entropy alloys (HEAs) in general—remains insufficiently understood. This dissertation systematically investigates the high-temperature creep deformation mechanisms of Fe28.2Ni18.8Mn32.9Al14.1Cr6 and its derivatives.

Creep mechanisms and associated microstructural changes were examined across a wide range of strain rates using strain-rate jump and constant-stress tests. Two dominant regimes were identified: dislocation glide/solute-drag at low strain rates, and dislocation climb at high …

First Principles Materials Discovery And Design For Photovoltaic And Solar Thermal Alloys Using High Throughput Methods, Andrew Pike

Dartmouth College Ph.D Dissertations

Materials selection has been a challenge since the dawn of time. With the advent of computational methods and high throughput databases, materials can be discovered and assessed before they are even synthesized. In this thesis I will discuss my work towards designing new materials for clean energy uses, especially alloys which have been underexplored from computational methods. To begin, I present a case study explaining the synthesis of the Yb₁₄ZnSb₁₁ thermoelectric material. Next, I explore the class of AM₂Pn₂ Zintl materials. From the previously identified BaCd₂P₂, it is suspected that …

Wear Of High Entropy Alloys: Understanding Effects Of Cryogenic Temperatures And Surface Nitriding On Wear Behavior, Aubrey Yu Tang

Dartmouth College Ph.D Dissertations

Cryogenic tribological applications have become increasingly important with the development and innovation of advanced equipment in aerospace, polar regions, superconductivity, and more. Traditional lubrication methods are not viable under these harsh environments, so metallic materials must be able to maintain excellent mechanical properties and withstand the constant impact and wear alone. High entropy alloys (HEAs) have emerged as potential candidates for these applications because of their wide variety of excellent room temperature properties and apparent improvement of mechanical properties of some HEAs at extremely low temperatures. Despite their promising nature, very limited work has been done on understanding the wear …

Optimizing Mn-Al Permanent Magnet Performance Through Control Of The Phase Transformation, Ternary Element Addition, And Advanced Processing, Thomas R. Keller

Dartmouth College Ph.D Dissertations

The growing need for electrical power in machines and vehicles brings with it a growing need for critical materials. The current high-performance permanent magnets (PMs) based on rare-earth (RE) elements Nd and Sm cannot escape the problem of raw material cost, geographic scarcity in the earth’s crust, and lack of circular global supply chains. This poses a problem of industrial ecology: can PMs be made from inexpensive, more abundant materials while still meeting sufficient performance criteria? PMs based on the magnetic τ phase of Mn-Al offer a possible alternative to REPMs. However, years of innovation have not yet achieved real-world …

Microstructure And Magnetic Properties Of Bulk Nanocrystalline Mnal, Anurag Chaturvedi, Rumana Yaqub, Ian Baker

Dartmouth Scholarship

MnAl is a promising rare-earth free permanent magnet for technological use. We have examined the effects of consolidation by back-pressure, assisted equal channel angular extrusion processing on mechanically-milled, gas-atomized Mn-46% at. Al powder. X-ray diffraction showed both that the extruded rod consisted mostly of metastable τ phase, with some of the equilibrium γ₂ and β phases, and that it largely retained the as-milled nanostructure. Magnetic measurements show a coercivity of ≤4.4 kOe and a magnetization at 10 kOe of ≤40 emu/g. In addition, extrusions exhibit greater than 95% of the theoretical density. This study opens a new window in …