Metallurgy Commons^™

Lafe0.925ti0.075o3 Perovskite Coated With Ethyl Cellulose: A High-Stability, Low-Hysteresis Platform For Advanced Humidity Sensing, Akhmad Futukhillah Fataba Alaih, Djoko Triyono, Rifqi Almusawi Rafsanjani

Makara Journal of Science

Humidity sensors are pivotal in numerous sectors, such as environmental monitoring, industrial automation, and health-care. This study presents the fabrication and detailed evaluation of an advanced humidity sensor using ethyl cellulose (EC)-coated LaFe_0.925Ti_0.075O₃ (LFTO) perovskite nanoparticles synthesized via the sol-gel method. The LFTO nanopar-ticles exhibited a mesoporous structure with an enhanced surface area, which significantly improved their moisture adsorption capabilities. The innovative application of EC coating addresses critical substrate adhesion issues, enhancing mechanical stability without compromising sensor sensitivity. Comprehensive performance evaluations revealed minimal hysteresis (

Feasibility Of Upcycling Spent Lithium-Ion Battery To Carbon Dioxide Capture Adsorbent, Chimezie Frank Onwudinjo

Master’s Theses

This study investigates the feasibility of repurposing spent lithium-ion battery (SLIB) to lithium orthosilicate (Li₄SiO₄), a high temperature carbon dioxide sorbent. Two synthesis pathways including conventional acid-leaching method (Scenario 1) and a pyrolysis-based route (Scenario 2) were explored. Additionally, techno-economic analysis (TEA) and lifecycle assessment (LCA) of the two processes were also performed. Different analytical characterization techniques were performed to understand the material properties of Li₄SiO₄ including surface area, crystallinity, morphology and thermal stability. CO₂ capture performance of the synthesized Li₄SiO₄ was tested in a thermogravimetric analyzer (TGA) using …

Nanostructured Cathode Catalysts For Aem Electrolysis: From Catalyst Design To Degradation And Hydrogen Dynamics, Yamini Kumaran

Electronic Theses & Dissertations (2024 - present)

Anion exchange membrane water electrolysis (AEMWE) presents a promising pathway toward cost-effective and sustainable hydrogen production by integrating the chemical robustness of alkaline systems with the compact, zero-gap design of proton exchange membrane electrolyzers. However, the widespread implementation of AEMWE is limited by the availability of highly active and durable platinum-group-metal (PGM)-free catalysts and by an incomplete understanding of their degradation behavior under realistic operating conditions.

This dissertation focuses on the development, characterization, and mechanistic investigation of nanostructured MoNi₄–MoO₂-based electrodes for efficient and stable hydrogen generation under alkaline and membrane-integrated environments. MoNi₄–MoO₂ nanorods …

Mxene-Based Materials For Enhanced Water Quality: Advances In Remediation Strategies, Ali Mohammad Amani, Milad Abbasi, Atena Najdian, Farzaneh Mohamadpour, Seyed Reza Kasaee, Hesam Kamyab, Shreeshivadasan Chelliapan, Mostafa Shafiee, Lobat Tayebi, Ahmad Vaez, Atefeh Najafian, Ehsan Vafa, Sareh Mosleh-Shirazi

Electrical & Computer Engineering Faculty Publications

Two-dimensional MXenes are promising candidates for water treatment because of their large surface area (e.g., exceeding 1000 m²/g for certain structures), high electrical conductivity (e.g., >1000 S/m), hydrophilicity, and chemical stability. Their strong sorption selectivity and effective reduction capacity, exemplified by heavy metal adsorption efficiencies exceeding 95 % in several studies, coupled with facile surface modification, make them suitable for removing diverse contaminants. Applications include the removal of heavy metals (e.g., achieving >90 % removal of Pb(II)), dye removal (e.g., demonstrating >80 % removal of methylene blue), and radioactive waste elimination. Furthermore, 3D MXene architecture exhibit enhanced performance in antibacterial …

Mechanisms Of Dendritic Shorting In Lithium Metal Batteries With Li7la3zr2o12 Solid Electrolytes, Lukas Karapin-Springorum

Pomona Senior Theses

Energy storage will play a crucial role in efforts to mitigate the effects of climate change caused by greenhouse gas emissions from human activity. Lithium metal batteries using solid electrolytes like Li₇La₃Zr₂O₁₂ have higher energy density than lithium-ion batteries, which may enable a more rapid and complete electrification of transportation. However, lithium metal batteries suffer from undesirable short-circuiting when metallic lithium deposits connect the two electrodes. It has been debated whether these lithium dendrites generally grow directionally from the anode or are generated by the reduction of lithium ions inside the solid electrolyte, …

Calcite Depression In Bastnaesite-Calcite Flotation System Using Organic Acids, Emmy Muhoza

Graduate Theses, Dissertations, and Problem Reports (ETD)

Bastnaesite is the primary source of light REEs, namely cerium (Ce), lanthanum (La), praseodymium (Pr), neodymium (Nd), to name a few. Bastnaesite is typically concentrated using the froth flotation beneficiation method. Flotation of bastnaesite suffers from high reagent consumption due to the similar surface characteristics of bastnaesite and associated gangue minerals, including calcite. Additionally, complex stages of high-temperature conditioning are often required to suppress the detrimental impact of dissolved calcium ions on the flotation of bastnaesite. This research seeks to investigate the capabilities of organic acids in the bastnaesite-calcite flotation systems to selectively depress calcite minerals and effectively chelate calcium …

Recovery Of Phosphorus From Florida Phosphatic Waste Clay, Amir Eskanlou

Graduate Theses, Dissertations, and Problem Reports (ETD)

This MS thesis examines the recovery of phosphorus (P) from Florida waste clay (WC). A comprehensive literature review revealed that: (i)-The most important values being lost to WC are P and rare earth elements (REEs). For the recovery of these values from WC, two crucial attempts are the removal of extremely fine-sized clays, followed by the recovery of phosphate content, which can pave the path for the recovery of REEs; (ii)-Any scientific/ technological solution should, at the same time, be economically and environmentally attractive to the industry. As such, moving from mostly chemical separation processes to the primarily physical/ physicochemical …

Magnetocaloric Effect Near Room Temperature In Quintenary And Sextenary Heusler Alloys, Benjamin D. White, R. I. Barabash, O. M. Barabash, I. Jeon, M. B. Maple

All Faculty Scholarship for the College of the Sciences

An inverse magnetocaloric effect is studied in Ni₂Mn_1+xX_1-x-type Heusler alloys. Principally known for their shape-memory properties, these alloys also exhibit significant entropy and temperature changes (ΔS and ΔT_Ad, respectively) under adiabatic conditions when a modest magnetic field is applied. We investigated the impact on magnetocaloric properties of introducing substantial chemical disorder on the X-site (X = Si, Ga, In), of replacing Ni with nonmagnetic Ag, and of replacing a small amount of Mn with Gd. While a reduction in ΔS is observed in the first two cases, we observe a significant enhancement …

Analysis Of Surface Integrity In Machining Of Aisi 304 Stainless Steel Under Various Cooling And Cutting Conditions, F. Klocke, B. Döbbeler, S. Lung, S. Seelbach, Ibrahim S. Jawahir

Institute for Sustainable Manufacturing Faculty Publications

Recent studies have shown that machining under specific cooling and cutting conditions can be used to induce a nanocrystalline surface layer in the workspiece. This layer has beneficial properties, such as improved fatigue strength, wear resistance and tribological behavior. In machining, a promising approach for achieving grain refinement in the surface layer is the application of cryogenic cooling. The aim is to use the last step of the machining operation to induce the desired surface quality to save time-consuming and expensive post machining surface treatments. The material used in this study was AISI 304 stainless steel. This austenitic steel suffers …

Thermoelectric Half-Heuslers: Synthesis, Processing, And Performance, Joseph Robert Croteau

Boise State University Theses and Dissertations

Thermoelectric half-Heusler compounds have potential to convert the heat wasted from industrial and transportation processes to useful electricity. Among the highest performing half-Heusler compounds are nano-structured bulk materials which have been arc-melted, pulverized into a nano-powder, and sintered by DC-hot press. High performing n- and p-type half-Heusler compounds with nominal composition of Hf_0.25Zr_0.75NiSn_0.99Sb_0.01 and Nb_0.75Ti_0.25FeSb, respectively, have been provided to us in both dense and powder form by our collaborators at the University of Houston. We consolidate these powders by SPS, refine these powders to improve both particle size …

Solar Cell Design Using Metamaterials, Yang Liu, Yitung Chen, Jichun Li

College of Engineering: Graduate Celebration Programs

Natural structure with simultaneous negative permittivity and permeability has not been discovered yet. However, using specially-designed metal embedded in dielectric bodies can achieve a kind of artificial negative index. This periodic structure which is smaller than the guided wavelength is known as a metamaterial. However, recent designs of metamaterials have some disadvantages when they are used in the application of solar cell. The perfect absorption is only within a narrow band, and for most of the solar spectrum, the absorption is no more than 10%. Here, a new kind of absorber for the solar spectrum has been designed and analyzed, …

Time-Dependent Crack Growth Behavior Of Alloy 617 And Alloy 230 At Elevated Temperatures, Shawoon Kumar Roy

UNLV Theses, Dissertations, Professional Papers, and Capstones

Two Ni-base solid-solution-strengthened superalloys: INCONEL 617 and HAYNES 230 were studied to check sustained loading crack growth (SLCG) behavior at elevated temperatures appropriate for Next Generation Nuclear Plant (NGNP) applictaions with constant stress intensity factor (K _max = 27.75 MPa[checkmark]m) in air. The results indicate a time-dependent rate controlling process which can be characterized by a linear elastic fracture mechanics (LEFM) parameter - stress intensity factor (K). At elevated temperatures, the crack growth mechanism was best described using a damage zone concept. Based on results and study, SAGBOE (stress accelerated grain boundary oxidation embrittlement) is considered the primary reason for …

Fundamental And Applied Experimental Investigations Of Corrosion Of Steel By Lbe Under Controlled Conditions: Kinetics, Chemistry Morphology, And Surface Preparation, John Farley, Allen L. Johnson

Transmutation Sciences Materials (TRP)

Advanced nuclear processes and facilities (e.g., transmutation of nuclear waste, fast reactors, and spallation neutron sources) impose special demands on materials, which must withstand high temperatures, high radiation fields, and chemical corrosion. Proposed schemes for transmuting nuclear waste require a nonmoderating coolant such as lead-bismuth eutectic (LBE) or liquid sodium. While LBE corrodes most steels, small amounts of oxygen in the LBE greatly reduces the corrosion rate, and could ideally re-grow a damaged oxide layer in situ. The protective oxide layer would thus be self-healing. However, a fundamental understanding of the role of oxygen and passivating oxide layers is presently …

Effect Of Silicon Content On The Corrosion Resistance And Radiation-Induced Embrittlement Of Materials For Advanced Heavy Liquid Metal Nuclear Systems, Ajit K. Roy

Transmutation Sciences Materials (TRP)

The beneficial effects of Si on both the metallurgical and corrosion properties of Cr-Mo steels have previously been demonstrated at UNLV. Therefore, additions of Si ranging from 0.5-2.0 weight percent (wt%) was attempted in this investigation to explore Si effect on both the high temperature tensile properties and corrosion behavior of T91 grade steel. Corrosion studies in the presence of molten LBE could not be performed due to a lack of proper experimental facilities at UNLV. Therefore, detailed corrosion studies involving Si-containing T91 grade steels were performed in an aggressive aqueous solution of acidic pH. Further, significant efforts have been …

Theoretical Modeling Of Protective Oxide Layer Growth In Non-Isothermal Lead Alloy Coolant Systems, Yitung Chen, Taide Tan, Jinsuo Zhang, Jichun Li

Transmutation Sciences Materials (TRP)

In advanced nuclear energy systems, lead alloys emerge as strong candidates for transmutation and advanced reactor systems as nuclear coolants and spallation neutron targets. However, it is widely recognized that corrosion of materials caused by lead alloys presents a critical barrier to their industrial use. A few experimental research and development projects have been set up by different groups such as at Los Alamos National Laboratory to study the corrosion phenomena in their test facilities and to develop mitigation techniques and materials. One of the central or main techniques under development is to use active control of oxygen thermodynamic activity …

Development Of Nanostructure Based Corrosion-Barrier Coatings On Steel For Transmutation Applications, Biswajit Das

Transmutation Sciences Materials (TRP)

Advanced transmutation systems require structural materials that are able to withstand high neutron fluxes, high thermal cycling, and high resistance to chemical corrosion. The current candidate materials for such structures are ferritic and ferritic-martensitic steels due to their strong resistance to swelling, good microstructural stability under irradiation, and the retention of adequate ductility at typical reactor operating temperatures.

In parallel, lead-bismuth eutectic (LBE) has emerged as a potential spallation target material for efficient production of neutrons, as well as a coolant in the accelerator system. While LBE has excellent properties as a nuclear coolant, it is also highly corrosive to …

Interaction Between Metal Fission Products And Triso Coating Materials, Clemens Heske

Fuels Campaign (TRP)

This project focuses on the chemical bonding and interface formation of metal fission products with the coating materials used in tri-isotropic (TRISO) fuel particles for gas-cooled reactors. By combining surface- and bulk-sensitive spectroscopic and microscopic methods, intermediate chemical phases at the interface, intermixing/diffusion behavior, and the electronic interface structure for different coating materials and metals are examined.

In detail, the project studies the interface formation of Pd, Cs, and Ag with SiC and pyrolytic carbon. Using SiC single crystals and highly-ordered pyrolytic carbon (HOPG) as substrates, interfaces are prepared under controlled conditions in an ultra-high vacuum environment and are studied …

Interaction Between Metal Fission Products And Triso Coating Materials, Clemens Heske

Fuels Campaign (TRP)

This project focuses on the chemical bonding and interface formation of metal fission products with the coating materials used in tri-isotropic (TRISO) fuel particles for gas-cooled reactors. By combining surface- and bulk-sensitive spectroscopic methods, intermediate chemical phases at the interface, intermixing/ diffusion behavior, and the electronic interface structure as a function of material (metal and coating materials) and temperature are examined.

In the past year, emphasis was placed on a detailed analysis and description of the Cs/SiC interface formation process.

Use Of Positron Annihilation Spectroscopy For Stress-Strain Measurements, Ajit K. Roy

Transmutation Sciences Materials (TRP)

During the past academic year, this project was focused on the characterization of residual stress in welded specimens consisting of austenitic and martensitic stainless steels using an activation technique based on the Positron Annihilation Spectroscopic (PAS) method. The extent of residual stress was expressed in terms of three line-shape parameters (S-, W- and T-). Further, efforts were made to characterize linear lattice defects such as dislocations in the vicinity of Fusion-Line (FL), Heat-Affected- Zone (HAZ), and the base material of the welded specimens using Transmission Electron Microscopy (TEM). The metallurgical microstructures at these three regions have also been evaluated by …

Fundamental And Applied Experimental Investigations Of Corrosion Of Steel By Lbe Under Controlled Conditions: Kinetics, Chemistry Morphology, And Surface Preparation, John Farley, Allen L. Johnson, Dale L. Perry

Transmutation Sciences Materials (TRP)

Advanced nuclear processes and facilities (e.g., transmutation of nuclear waste, fast reactors, and spallation neutron sources) impose special demands on materials, which must withstand high temperatures, high radiation fields, and chemical corrosion. Proposed schemes for transmuting nuclear waste require a nonmoderating coolant such as lead-bismuth eutectic (LBE). While LBE corrodes most steels, small amounts of oxygen in the LBE greatly reduces the corrosion rate, and could ideally re-grow a damaged oxide layer in-situ. The protective oxide layer would thus be self-healing. However, the fundamental understanding of the role of oxygen and passivating oxide layers is presently incomplete.

During the present …

Effect Of Silicon Content On The Corrosion Resistance And Radiation- Induced Embrittlement Of Materials For Advanced Heavy Liquid Metal Nuclear Systems, Ajit K. Roy

Transmutation Sciences Materials (TRP)

This task is focused on the evaluation of the effects of silicon content on both the corrosion behavior and radiation-induced embrittlement of martensitic stainless steels having compositions similar to that of modified 9Cr-1Mo steel, also known as T91 grade steel. T91 grade steel was selected to be a candidate structural material to contain molten lead-bismuth eutectic (LBE), which can act both as a target material and a coolant during the spallation process. The operating temperature during this process may range from 420-550 °C. Thus, moderate tensile strength of the containment material (T91) is a major requirement.

The beneficial effects of …

Theoretical Modeling Of Protective Oxide Layer Growth In Non-Isothermal Lead Alloy Coolant Systems, Yitung Chen, Jinsuo Zhang, Jichun Li

Transmutation Sciences Materials (TRP)

The goal of the proposed research project is to provide basic understanding of the protective oxide layer behaviors and to develop oxide layer growth models of steels in non-isothermal lead-alloys (lead or lead-bismuth eutectic) coolant systems. Precise studies and simulations of all hydrodynamics with thermal conditions encountered in practical coolant loop systems by use of different flowing conditions in the laboratory are difficult and expensive, if not impossible. Therefore it is important and necessary to develop theoretical models to predict the protective oxide layer behaviors at the design stage of a practical lead-alloy coolant system, to properly interpret and apply …

Development Of Nanostructure Based Corrosion-Barrier Coatings On Steel For Transmutation Applications, Biswajit Das

Transmutation Sciences Materials (TRP)

Advanced transmutation systems require structural materials that are able to withstand high neutron fluxes, high thermal cycling, and high resistance to chemical corrosion. The current candidate materials for such structures are ferritic and ferritic-martensitic steels due to their strong resistance to swelling, good microstructural stability under irradiation, and the retention of adequate ductility at typical reactor operating temperatures.

In parallel, lead-bismuth eutectic (LBE) has emerged as a potential spallation target material for efficient production of neutrons, as well as a coolant in the accelerator system. While LBE has excellent properties as a nuclear coolant, it is also highly corrosive to …

Effect Of Silicon Content On The Corrosion Resistance And Radiation-Induced Embrittlement Of Materials For Advanced Heavy Liquid Metal Nuclear Systems: Quarterly Progress Report (November 2005 – January 2006), Ajit K. Roy

Transmutation Sciences Materials (TRP)

This task is intended to study the effect of Si content not only on the corrosion resistance but also on the radiation-induced embrittlement of martensitic stainless steels. The susceptibility of these alloys with different Si content to stress corrosion cracking, general corrosion and localized corrosion will be evaluated in the molten LBE and aqueous environments of different pH values using state-of-the-art testing techniques. Testing in the aqueous media is intended to develop baseline data for comparison purpose. Radiation-induced embrittlement of these alloys will initially be studied by irradiating the test specimens with bremmstrahlung gamma radiation from 20-40 MeV electron beams …

Theoretical Modeling Of Protective Oxide Layer Growth In Non-Isothermal Lead-Alloys Coolant Systems: Quarterly Progress Report (01/01/06- 03/31/06), Yitung Chen

Transmutation Sciences Materials (TRP)

Research highlights:

• A cellular automaton model using method of global restructuring on the growth and corrosion during the formation of the passive layer has been developed.

• A stochastic model, which combines the surface growth and internal oxidation, has been developed to explain the oxidation mechanism of steels in liquid lead alloys.

• Two conference papers have been accepted and will be presented in 2006 International Congress on the Advances in Nuclear Power Plants (ICAPP '06).

Fundamental And Applied Experimental Investigations Of Corrosion Of Steel By Lbe Under Controlled Conditions: Kinetics, Chemistry Morphology, And Surface Preparation, John Farley, Allen L. Johnson, Dale L. Perry

Transmutation Sciences Materials (TRP)

Advanced nuclear processes such as the transmutation of nuclear waste, fast reactors, liquid-metal-cooled reactors, and spallation neutron sources require advanced materials systems to contain them. The required structural materials must be stable in the presence of nonmoderating coolants. A prime candidate for such a coolant is Lead Bismuth Eutectic (LBE). Materials in these systems must be able to tolerate high neutron fluxes, high temperatures, and chemical corrosion. Unfortunately, LBE corrodes stainless steel.

The corrosive behaviors of structural materials in LBE are not well understood. The Russians have over 80 reactor-years experience with LBE coolant in their Alpha-class submarine reactors. The …

Theoretical Modeling Of Protective Oxide Layer Growth In Non-Isothermal Lead Alloy Coolant Systems, Yitung Chen, Jinsuo Zhang, Huajun Chen, Jichun Li

Transmutation Sciences Materials (TRP)

The goal of this research project is to provide a basic understanding of the protective oxide layer behaviors and to develop oxide layer growth models of steels in non-isothermal lead alloys (lead or lead-bismuth eutectic) coolant systems. Precise studies and simulations of all hydrodynamics with thermal conditions encountered in practical coolant loop systems by use of different flowing conditions in the laboratory are difficult and expensive, if not impossible. Therefore it is important and necessary to develop theoretical models to predict the protective oxide layer behaviors at the design stage of a practical lead-alloy coolant system, to properly interpret and …

Corrosion Mechanisms And Kinetics Of Steels In Lead-Bismuth Eutectic: Quaterly Report, Allen L. Johnson, John Farley

Transmutation Sciences Materials (TRP)

A large number of studies of corroded samples were conducted using SEM, XPS, probe, and the TEM. Samples from the DELTA loop at LANL and from other sources were examined. Also, the investigation of 316 class stainless steel in LBE is continuing.

Corroded samples of D-9 steel have been in the process of being studies, which is a variant of 316 stainless steel that is optimized for resistance to swelling. The D-9 samples are notable for the process in which a localized failure of the protective oxide layer becomes widespread corrosion. The research group is examining the D-9 samples using …

Effect Of Silicon Content On The Corrosion Resistance And Radiation- Induced Embrittlement Of Materials For Advanced Heavy Liquid Metal Nuclear Systems, Ajit K. Roy

Transmutation Sciences Materials (TRP)

This task is primarily focused on the evaluation of the effect of Si content on the susceptibility of modified 9Cr-1Mo-0.24V steel to stress corrosion cracking (SCC) and localized cracking in both molten lead-bismuth eutectic (LBE) and an aqueous solution of acidic pH.

Further, significant efforts are in progress to characterize the deformation mechanism of modified T91 grade steel as a function of temperature and strain rate. Simultaneously, surface analyses of the tested materials are ongoing using state-of-the-art techniques including scanning electron microscopy (SEM) and transmission electron microscopy (TEM).

Corrosion Barrier Development For Lbe Corrosion Resistance: Quarterly Report (April 2006), Biswajit Das

Transmutation Sciences Materials (TRP)

As reported in the last quarterly report, synthesis of Cr nanowires was found to be problematic in terms of uniform coverage. Hence Ni was identified as the alternative metal to form the nanowires. The purpose of the metal nanowires is to provide structural integrity to the nanoporous alumina, as well as a second defense mechanism against corrosion by oxidizing in case the top alumina layer is compromised. Nickel was selected due to its established electrochemical synthesis procedure. While Ni can provide very good structural integrity to the porous alumina, one potential problem is its higher dissolution rate in LBE. However, …