Metallurgy Commons^™

Recovery Of Phosphorus From Florida Phosphatic Waste Clay, Amir Eskanlou

Graduate Theses, Dissertations, and Problem Reports

This MS thesis examines the recovery of phosphorus (P) from Florida waste clay (WC). A comprehensive literature review revealed that: (i)-The most important values being lost to WC are P and rare earth elements (REEs). For the recovery of these values from WC, two crucial attempts are the removal of extremely fine-sized clays, followed by the recovery of phosphate content, which can pave the path for the recovery of REEs; (ii)-Any scientific/ technological solution should, at the same time, be economically and environmentally attractive to the industry. As such, moving from mostly chemical separation processes to the primarily physical/ physicochemical …

Application Of 3d Printing Technology In Porous Anode Fabrication For Enhanced Power Output Of Microbial Fuel Cells, Bin Bian

Electronic Thesis and Dissertation Repository

Microbial fuel cells (MFCs) are widely researched for application in wastewater treatment. However, the current anodes used in MFCs often suffer from high fabrication cost and uncontrollable pore sizes. In this thesis, three-dimensional printing technique was utilized to fabricate anodes with different micro pore sizes for MFCs. Copper coating and carbonization were applied to the printed polymer anodes to increase the conductivity and specific surface area. Voltages of MFCs with various anodes were measured as well as other electrochemical tests such as linear sweep voltammetry and electrochemical impedance spectroscopy. 3D copper porous anode produced higher maximum voltages and power densities …

Sustainable Disposal Of Coal Processing Waste Streams, Mohammad Rezaee

Theses and Dissertations--Mining Engineering

Modern coal preparation facilities incorporate a wide array of solid-solid and solid-liquid separation processes for rejecting mineral matter to meet market specifications. The coarse mineral matter is typically placed into engineered refuse piles whereas the fine refuse is either stored in impoundments or co-disposed with the coarse refuse. The discharge water from the refuse material represents an environmental concern due to the potential release of trace elements, and the subsequent elevation of total dissolved solids and conductivity. The research findings reported in this dissertation addresses sustainable coal processing waste disposal through using strategies aimed at minimizing the environmental impacts. To …

Ocena Wielkości Emisji Do Powietrza Z Arcelormittal Poland S.A. Oddział W Krakowie W Odniesieniu Do Standardów Unii Europejskiej, Marian Mazur, Marek Bogacki, Robert Oleniacz

Robert Oleniacz

The work presents emission factors of main air pollutants for installations of ArcelorMittal Poland S.A. Unit in Krakow (Poland) in comparison with analogous characteristic emissions for iron and steel industry in West Europe. In the comparison four installations (to coke, sinter, pig iron and steel production) were taken into consideration. The emission rates from ArcelorMittal Poland S.A. Unit in Krakow were estimated on the basis of the emission levels and production data from 2004, when took place the most significant production of liquid steel during last several years. As a result of the analysis, most the emission factors (with the …

Assessment Of Ecological Effects Of The Implementation Of Continuous Casting Of Steel, Marian Mazur, Marek Bogacki, Robert Oleniacz, Agnieszka Łopata

Robert Oleniacz

The article presents a complex analysis of the impact of the technology of continuous casting of steel (CCS) on the rate of the air pollutant emissions from one of the Polish steel and iron plants. The emission sources occurring in the production process have been identified and their rate has been determined. The implementation of CCS has brought about significant changes in the production cycle of the steel plant and it also has caused an increase of the production effectiveness of steel products. The calculated environment effects have shown a considerable emission decrease of all pollutants in the scale of …

Wpływ Związków Metali Alkalicznych W Procesie Spiekania Rud Na Emisję Pyłów, Marian Mazur, Marek Bogacki, Robert Oleniacz

Robert Oleniacz

The work shows the impact of alkali metals in the sintering process on effectiveness of the electrostatic precipitator and dust emissions into the air. The results of analysis of the content of Na and K in dust discharged from the sinter strand and emitted to the air are presented. It was found that this content is subject to large fluctuations and significantly increases in the dust phase after electrostatic precipitators. Using the balance sheet data, the effect of loads of Na2O and K2O compounds contributed to the sinter mix on emissions of dust. It was also observed high variability of …

Wpływ Wprowadzenia Ciągłego Odlewania Stali Na Wielkość Emisji Zanieczyszczeń Z Huty Katowice, Marian Mazur, Marek Bogacki, Robert Oleniacz

Robert Oleniacz

The paper presents the results of research carried out in 1999 in the Department of Continuous Casting of Steel (CCS) Machines in "Katowice" Steelworks in Dąbrowa Górnicza (Poland), whose main objective was the identification of emission sources of dust and gaseous pollutants, determination of emission factors and assessment of environmental effects associated with the operation of this technology. Particular attention was paid for assessing the impact of the introduction the CCS technology to reduce total emissions from "Katowice" Steelworks.

English title: Impact of the introduction of continuous casting of steel on pollutant emissions from "Katowice" Steelworks.

Bezpośrednie I Pośrednie Efekty Wprowadzenia Ciągłego Odlewania Stali W Bilansie Emisji Zanieczyszczeń Z Huty Żelaza, Marian Mazur, Marek Bogacki, Robert Oleniacz

Robert Oleniacz

This paper presents a comprehensive analysis of the impact of continuous casting technology on emissions of air pollutants from "Katowice" Steelworks in Dąbrowa Górnicza (Poland). Sources of emissions occurring in the manufacturing process and emissions levels have been identified. Implementation of continuous casting of steel has increased the efficiency of production and brought substantial ecological effects.

English title: Direct and indirect effects of introduction of continuous casting of steel in the balance sheet of pollutant emissions from "Katowice" Steelworks.

Związki Siarki Emitowane Z Procesu Wielkopiecowego, Marian Mazur, Marek Bogacki, Robert Oleniacz

Robert Oleniacz

The article describes the problem of the presence of sulfur in the blast furnace process and identifies emission sources of sulfur compounds in this process. On the basis of the measurements and calculations, the types and quantities of these compounds emitted to the air were determined. It was found that pig iron smelting in a blast furnace causes emissions of COS, SO2 and H2S. These emissions occur by losses of blast furnace gas (COS and SO2), transport of blast furnace slag inside the furnace hall (SO2) and treatment of the slag by granulation (H2S). However, the most important are only …

Emisja Związków Fluoru Z Procesów Hutnictwa Żelaza, Marian Mazur, Marek Bogacki, Robert Oleniacz

Robert Oleniacz

The paper presents the results of a comprehensive study of issues related to emissions of fluorine compounds from ferrous metallurgy processes carried out over the last few years. As part of this study raw materials used in these processes were analyzed in terms of fluorine content and its impact on the amount of air emissions of fluorine compounds. Also determined by measuring the concentration levels and emissions of fluorine in the gaseous and solid phase, including water-soluble compounds (considered to be toxic).

English title: Emissions of fluorine compounds from the processes of ferrous metallurgy.

Ocena Oddziaływania Na Środowisko Na Przykładzie Zabudowy Pieca Indukcyjnego W "Krakodlew" S.A., Marian Mazur, Marek Bogacki, Robert Oleniacz

Robert Oleniacz

The paper presents the procedure and the results of the environmental impact assessment for the induction furnace installed in the company "Krakodlew" S.A. in Krakow (Poland). This furnace will allow heating and keeping the liquid feed (pig iron) and adjust the chemical composition, which will allow for the production of high-quality heavy castings. The need to perform an environmental impact assessment for objects of this type results from the binding legal regulations in Poland. The analysis included all the main components of the environment: air, soil, vegetation, soil and water environment, land surface and acoustic climate. It was found that …

Emisja Związków Siarki Z Procesu Wielkopiecowego, Marian Mazur, Marek Bogacki, Robert Oleniacz

Robert Oleniacz

The paper describes the problem of the presence of sulfur in the blast furnace process and identifies emission sources of sulfur compounds in this process. On the basis of the measurements and calculations, the types and quantities of these compounds emitted to the air were determined. It was found that pig iron smelting in a blast furnace causes emissions of COS, SO2 and H2S. These emissions occur by losses of blast furnace gas (COS and SO2), transport of blast furnace slag inside the furnace hall (SO2) and treatment of the slag by granulation (H2S). However, the most important are only …

Wpływ Komponentów Alkalicznych W Procesach Spiekania I Wielkopiecowym Na Technologię I Emisję Zanieczyszczeń, Marian Mazur, Ryszard Benesch, Andrzej Łędzki, Robert Oleniacz

Robert Oleniacz

The paper presents the impact of alkali metals on sintering and blast furnace processes and air pollutant emissions including particulate matter. On the basis of the balance calculations, it was found that the main source of alkali (Na2O and K2O) in the sintering process is a raw mixture unweathered. The calculations showed that the level of dust emissions from the sinter strand to a large extent depends on: the total alkali content in a mixture of sinter, ash content in coke breeze, K2O concentration in coke ash and alkalinity of the produced sinter. Alkali metals are introduced into the blast …

Studies In Modulation Of Interfacial Reactions For Certain Sulphide Minerals, Robert Owen Beyaert

Bachelors Theses and Reports, 1928 - 1970

No abstract provided.

Production Of Standard-Grade Ferromanganese In An Electric Arc Furnace, Force F. Baney Jr.

Bachelors Theses and Reports, 1928 - 1970

The investigations conducted in this project were essentially concerned with the effects of various compositions of two different slag systems upon the increased recovery of manganese in a standard-grade ferromanganese.

Investigation Of The Ternary System Silver-Aluminum-Indium (Ag-Al-In), Elvin H. Beardslee

Bachelors Theses and Reports, 1928 - 1970

This thesis paper contains material pertaining to & preliminary investigation of the ternary system Ag-Al-In. Procedures in this preliminary investigation are discussed in detail.

Preliminary Examination Of The Aluminum Corner Of The Ternary System Aluminum-Silver-Indium (A1-Ag-In), Jerome J. Blake

Bachelors Theses and Reports, 1928 - 1970

In this paper the author attempts to lay the groundwork for future work on the Al-Ag-In system.

Crystal Habit Modification Of Sodium Chlorate, Michael R. Keegan

Bachelors Theses and Reports, 1928 - 1970

All single crystals have a particular habit or morphology. The crystal habit refers to the relative degree of development of crystallographic planes into surfaces which make up the external appearance of the single crystal.

In this paper, NaClO3 is used as a parent crystal. Its simple cubic habit is modified to tetrahedral by the use of impurities of SO4=, S2O3=, Cr2O7=, and NO3-. The degree of habit change is studied as a function of impurity concentration and temperature. The problem and phenomena are explained in terms of surface chemistry and thermodynamics.

Physico-Chemical Principles Of Sixteenth Century Metallurgy, Robert E. Johnson

Bachelors Theses and Reports, 1928 - 1970

Following a review of sixteenth century metallurgical literature and a discussion of Gibbs free energy, this thesis discusses thermodynamic considerations of galena (PbS) reduction by iron from a lead assay of this period. The importance of fluxes in this assay is emphasized. The discussion covers both equilibrium and non-equilibrium conditions at 1100 degrees Celsius. Possible substitutes for iron are also covered.

Information from twenty-one small controlled lead assays is correlated with the thermodynamic discussion to determine the purpose of each constituent in the assay.

The Beneficiation Of Titaniferous-Magnetite Sands, Ronald Lloyd Nordwick

Bachelors Theses and Reports, 1928 - 1970

The purpose of this investigation of beneficiation methods is to develop and study possible economic methods for recovering an iron-titanium concentrate of sufficient purity to meet metallurgical requirements for subsequent direct reduction to pig iron and a high titanium slag.

Stress-Corrosion Cracking Of Brass, Paul A. Fossey

Bachelors Theses and Reports, 1928 - 1970

the mechanism of stress-corrosion cracking of brass has been sought for many years. Investigators have proposed many mechanisms, but each of these mechanisms has always had several drawbacks. This paper presents an account of experimental work done in the laboratory on this subject and compares it to the work of previous investigations. It evaluates the mechanisms presented by investigators and shows the failures of these mechanisms. A theory of Nitrogen Embrittlement is presented and an evaluation of this theory with experimental work follows.

Experimental Arc Furnace Smelting Of Titaniferous Iron Sands From The Northern Oregon Coast, Allan P. Herring

Bachelors Theses and Reports, 1928 - 1970

This investigation is an attempt to experimentally smelt titaniferous iron sands from the Northern Oregon Coast in a laboratory arc furnace.

The Effect Of Ph Upon Chelation Reactions In Montmorillonite Clays, Joseph Michael Keane

Bachelors Theses and Reports, 1928 - 1970

The purpose of this thesis is to investigate several chelation reactions and determine the effect of variable pH upon these reactions.

An Investigation Of The Sintering Of Iron-Wire Compacts, George L. Vivian

Bachelors Theses and Reports, 1928 - 1970

A study of the sintering of iron has been made by observing the rate of bonding of iron wires wound on iron spools. The specimens were sintered at a constant temperature of 850c in vacuum furnaces capable of producing pressures of 10-5 to 10-4 mm of mercury, and the growth of the bond between wires was observed as a function of time.

It has been concluded that the volume-diffusion mechanism is strongly operating in the sintering of iron at 850c, but in an evacuated system, the evaporation-condensation mechanism also contributes to the sintering process.

The Identification Of Montana Clays By X-Ray Analysis, David Stephen Malyevac

Bachelors Theses and Reports, 1928 - 1970

The purpose of this study is to identify the various Montana clay minerals by means of X-ray diffraction. The ultimate aim of this investigation is to identify the different clay mixtures through an analysis of their respective diffraction patterns, and diffraction patterns obtained after various chemical and thermal treatments.

Effect Of Recovery On The Recrystallized Grain-Size Of High Purity Aluminum, Rodney L. Helterline

Bachelors Theses and Reports, 1928 - 1970

When a cold-worked metal is annealed, it’s physical properties hange as a result of a new grain structure. The annealing treatment is divided into three stages according to the changes that occur in the distorted metal: (1) recovery, (2) recrystallization, and (3) grain growth.

Investigation Of Inclusions In Armco Ingot Iron, Edwin J. Duncan

Bachelors Theses and Reports, 1928 - 1970

Various chemical and electrolytic separation methods were investigated in an attempt to separate the in­clusions in Armco ingot iron. Residues obtained were X-rayed for identification purposes. The microstruc­tures of this iron were studied with the object of de­termining the relative sizes, locations, and possible compositions of the inclusions.

The Design And Construction Of An Electrolytic Cell For Aluminum Reduction, Thomas H. Melrose

Bachelors Theses and Reports, 1928 - 1970

The purpose of this investigation was to design and construct a laboratory size electrolytic cell in which to reduce alumina, using the same basic materials that are used in a commercial size cell. The cell was designed to have a capacity of approxi­mately 100 grams of metallic aluminum produced every 8 hours. The cell was constructed so it could be operated continuously.

Polarography Of Indium, John Jackson

Bachelors Theses and Reports, 1928 - 1970

The purpose of this thesis is to study the various aspects of the polarography of indium. The eventual goal would be to develop a method of analyzing indium in unknowns. The investigation is approached by studying the indium ions in various electrolytes and in various concentrations.

Geology Of The Ragged Point Oil Field Musselshell County, Montana, David M. Amos

Bachelors Theses and Reports, 1928 - 1970

The Ragged Point oil field is located in Northwest Musselshell County, in the Lake Basin field of central Mon­tana, and on the western border of the Great Plains region. The surface topography is that of a plain marked by erosion and moderate folding. The stratigraphy of central Montana shows periodic marine invasions from the Cordilleran trough, with normal marine limestones interbedded with sandstone sand shales. These sediments are over 12,000 feet thick, with the Creta­ceous Eagle and Colorado formations exposed at the surface on the Ragged Point anticline. Undifferentiated Cambrian lime­stones and shales are the oldest rocks encountered in drilling.