Ceramic Materials Commons^™

Phase Equilibria In Aqueous Magnesium Chloride, Sulfate, Chromate And Phosphate Systems, Ladawan Urwongse

Doctoral Dissertations

"In the first part of the present study, which is presented in Paper I, solubility of MgO in aqueous HCl solutions at 23° ± 3°C was measured and combined with analyses of neat magnesium oxychloride cements to construct an equilibrium phase diagram for the system MgO-MgCl₂-H₂O. Invariant liquids in equilibrium with Mg(OH)₂ and 5Mg(OH)₂·MgCl₂·8H₂O (5.1.8), with 5·1·8 and 3Mg(OH)₂·MgCl₂·8H₂O (3·1·8), and with 3·1·8 and MgCl₂·6H₂O were located at 0.8 ± 0.2 MgO, 17.0 ±0.5 MgCl₂; at 1.0 …

Electrical Degradation In High Purity Barium Titanate, Jeffrey Duncan Keck

Doctoral Dissertations

"The stability of BaTiO₃-type insulators to DC fields has long been recognized as one of the important factors in determining the quality of a capacitor which uses such a material as its dielectric. The slow increase of the electrical conductivity of an insulator which is stressed by DC fields at levels below the breakdown strength is normally termed degradation. Since degradation is a very common malady to the ceramic capacitor manufacturers, many studies have been conducted over the past two decades in efforts to learn how to remedy the problem.

The results of previous studies have shown that …

Characterization Of Heat-Treated Nickel And Gold Films On Silicon Single Crystals, Ki Hyun Yoon

Doctoral Dissertations

"An experimental electron impact ionization source was used to determine the presence of various neutral atoms and molecules on metallized and bare surfaces of silicon wafers. The metallization consisted of thin films of nicke l and gold separately and in combination. The major surface contaminates on all samples were found to be F, Na, Cl, K, CO, and CO₂. The surface concentration of these species was found to be sensitive to the sample temperature up to 550 °C, the maximum temperature used in this study.

In the course of the mass spectrometric study, it was found that crystallites …

Phase Equilibria And Transformations In Potassium Sulfate, Chromate, Molybdate, And Tungstate, Roy Richard Ramey

Doctoral Dissertations

"Thermal expansion and transformations of K₂SO₄, K₂CrO₄, K₂MoO₄, and K₂WO₄ were studied by high temperature diffractometry, differential thermal analysis, and dilatometry. K₂SO₄ and K₂CrO₄ transform from an orthorhombic to a hexagonal structure at 580°C and 670°C respectively, with initiation of the transformation probably related to increased amplitude of S-O tetrahedral vibrations. K₂MoO₄ and K₂WO₄ transform from a monoclinic to an orthorhombic structure at 300° and 370°C respectively. A minor K₂MoO_{4 …}

Solid Transformations And Premelting Phenomena In Fluorite Structures And The System Srcl₂Bacl₂, Damri Sukhotanang

Doctoral Dissertations

"Thermal expansion and phase transformations in CaF₂, BaF₂, SrCl₂, and BaCl₂ were studied by high temperature x-ray diffractometry, differential thermal analysis, and thermodilatometric analysis. Thermal expansion characteristics of CaF₂, BaF₂ and SrCl₂ are very similar. The structures expand normally at lower temperatures and depart substantially from linearity at higher temperatures, because of formation of defects and disordering of anions. At high temperatures CaF₂ and BaF₂ react with water vapor, even at low humidities, forming oxides and emitting HF, leading to difficulty in observation of phase transformations. SrCl …

Initial Surface Reactions And Nucleation Kinetics Of Boron On Atomically Clean Molybdenum Substrates, Richard Eugene Moore

Doctoral Dissertations

"A study of the chemical vapor deposition (CVD) of boron from boron triiodide (BI₃) on molybdenum has been done with field emission microscopy (FEM) and low energy electron diffraction (LEED).

A correlation of the efficiency by which BI₃ is effectively dissociated to form adsorbed boron, and the temperature of the substrate has been shown through work function measurements on the boron covered molybdenum field emitter surfaces. The boron-induced work function change of molybdenum has been shown to be in agreement with a theoretical model which predicts positive, as well as negative work functions for adsorbate-substrate systems. It …

Synthesis And Properties Of Cadmium Manganese Ferrites, B. W. Jong

Doctoral Dissertations

"The formation sequence of (Cd,Mn,Fe) (Mn,Fe)₂O₄ from the individual oxides,x CdO + (1-x) MnCO₃ + α-Fe₂O₃,was found by X-Ray diffraction. Cd(Mn,Fe)₂O₄ was formed completely from CdO·Fe₂O₃ and CdO·Fe₂O₄ at 900°C and reacted with MnFe₂O₄ for 0 < x < 0.5 and with α-Fe₂O₃ for 0.5 < x < 1.0 to form a single phase of (Cd,Mn,Fe) (Mn,Fe)₂O₄ at 1150°C. This is the first time that the details involved in the formation sequence of CdMn-ferrite have been shown. A mixture of 0.5 CdO + 0.5 MnCO₃ + α-Fe₂O₃ was calcined at 900°C for 2 hrs forming Cd(Mn,Fe)₂O₄ with no Cd present in the other phases. Sintering was accomplished at 1150°C for 30 minutes forming a single phase of Cd₀.₅Mn₀.₅Fe₂O₄ with a bulk sintered density of 98-99% of the X-Ray density. The rate of changing density followed the relationship, p = K ln t + c, at temperatures between 1050°C and 1300°C. Magnetic properties of CdₓMn₁₋ₓFe₂O₄ were affected by composition x. A relationship, B = gx + h, was found between maximum magnetic flux density B and composition x at room temperature for 0 <̲ x <̲ 0.3. This was rationalized by a modification of Néel's theory. The maximum magnetic flux density decreased with increasing cadmium concentration for 0.3 < x <̲ 0.5. This decrease was attributed to the changing direction of the magnetic moment in the octahedral site sub-lattice according to the superexchange theory. No magnetic properties were observed due to the formation of a compensated antiferromagnetic phase for 0.5 < x <̲ 1.0. Maximum magnetic flux density increased with bulk density, while the coercive force decreased with the grain growth and the initial permeability increased with the bulk density and grain size. A stator core used for a-c electric motor application was formed by pre-sintering at 900⁰C for 2 hrs. Slots were then sawed with a tungsten carbide blade and final sintering was accomplished at 1150⁰C for 1 hr"--Abstract, pages iii-iv.

A Study Of The Solid Regions In The System Zr-Te, Frances Dolores Jenkins

Doctoral Dissertations

"Relative intensity measurements of X-ray powder diffraction lines were made of compositions in the region ZrTe₀.₅ to ZrTe₂.₀, fired between 600º and 817ºC in evacuated sealed tubes. The experimental relative intensities of samples between ZrTe and ZrTe₂ were compared with values calculated for several theoretical models with different Zr vacancy ordering schemes and Te vacancy concentrations. The most probable structural model for compositions in the range ZrTe to ZrTe₁.₅ is one in which the number of Zr vacancies located at z = 0 ranges from 0% to 30%, with the concentration of Te vacancies ranging from 0 to 35%. A …

Structure And Properties Of Silver Borate Glasses, Edward Nashed Boulos

Doctoral Dissertations

"Clear glasses form in the system Ag₂O-B₂O₃ up to about 35 mol.% (65 wt.%) Ag₂O. Infrared absorption, thermal expansion and density data indicated an analogy to the Na₂O-B₂O₃ system. Pentaborate-triborate group pairs appear to be formed upon the addition of Ag₂O to B₂O₃ up to 20 mol.% Ag₂O and diborate groups from 20 to 33 mol.% Ag₂O. This interpretation is supported by the comparison of the infrared absorption spectra of quenched and crystallized glasses. One crystallization product ,Ag₂O.4B₂O₃, has been identified previously. A new compound starts to appear at 28 mol.% Ag₂O. Silver is generally present as a network modifier …

Internal Friction Of Ion Exchanged Li₂O•Al₂O₃•2sio₂ Glasses, A. Ismail A. Abdel-Latif

Doctoral Dissertations

"Li₂O•Al₂O₂•2SiO₂ glass fibers were ion-exchanged from 1 to 300 minutes in a sodium nitrate bath at 366ºC. The internal friction was measured along with the lithium and sodium concentration profiles. As sodium progressively replaced lithium, the alkali internal friction peak became smaller while a new peak (mixed alkali peak) appeared and increased in magnitude. These changes in the internal friction are similar to those that occur upon the addition of a second alkali to glasses prepared by conventional melting. The magnitude of both internal friction peaks in ion exchanged glasses was dependent on the overall glass composition. The magnitude of …

Surface Reactions Of Boron With Clean Tungsten Substrates, Thomas A. Flaim

Doctoral Dissertations

"A model developed to predict adsorbate-induced work-function changes for thermionic emitters is shown here to apply to a more general class of electron emission phenomena and a much broader range of adsorbates. This model predicts that chemically, vapor-deposited boron will increase the work function of a clean tungsten substrate at coverages between 0 and 1 monolayer. This is the first time that a single model has been shown to predict both positive and negative work function changes for different adsorbates. The reactions of chemically, vapor-deposited (CVD) boron with clean tungsten substrates were studied using field emission microscopy (FEM) and low …

Some Effects Of Oh Groups On Sodium Silicate Glasses, Mokhtar Sayed Maklad

Doctoral Dissertations

"Glasses of various compositions in the Na₂O-SiO₂ system were prepared with different levels of OH concentration. Phase separation kinetics, thermal expansion, radiation induced optical absorption, and internal friction of these glasses were studied. The increase in OH content in these glasses was found to (a) enhance the rate of phase separation; (b) increase thermal expansion above the glass temperature and change the dilatometric softening temperature in a way that depends on microstructure; (c) increase the radiation induced optical absorption bands associated with positive hole centers and decrease those associated with electron trap centers; and, (d) decrease the low temperature alkali …

Temperature Variation In Distribution Of Relaxation Times In Aluminosilicate Glasses, David Wayne Moore

Doctoral Dissertations

"The distribution of relaxation times for the alkali peak in a Li₂ O·A1₂O₃ ·2.0SiO₂ glass and for the mixed alkali peak in a 0.5Li₂O·0.5Na₂O·A1₂O₃·2.OSiO₂ glass was studied using the internal friction technique. A lognormal distribution of relaxation times provided the best agreement with the experimental data. The ß parameter of the lognormal distribution function, which is related to the half-height peak width, varied with temperature, indicating that the distribution of relaxation times is dependent upon the activation energy and the activation entropy of the relaxation mechanism. The major contributor to the distribution of relaxation times is a wide distribution in …

Diffusion And Internal Friction In Sodium-Rubidium Silicate Glasses, Gary L. Mcvay

Doctoral Dissertations

"The internal friction and self diffusion coefficients of sodium and rubidium ions for (1 - X) Na₂O·X Rb₂O·3 SiO₂ glasses have been measured. The diffusion measurements employed radioactive isotopes and a thin sectioning technique and extended from 350 to 500°C. Internal friction measurements were made from -150 to 500°C and at frequencies of 0.05 to 6000 Hz. The maximum height for the mixed alkali internal friction peak occurs at the composition where the sodium and rubidium diffusion coefficients are equal. It is concluded that the mechanism responsible for the mixed alkali peak is a cooperative rearrangement of sodium-rubidium ions and …

A Crystallization Study Of A Tetrasilicic Fluormica Glass, William H. Daniels

Doctoral Dissertations

"The transformation of a synthetic mica composition K₂Mg₅Si₈O₂₀F₄ from amorphous to crystalline structure was studied isothermally at selected temperatures from 560°C to 1150°C. thermal changes associated with the transformation were followed by differential thermal analysis techniques. Structural changes promoted by the isothermal treatments were observed by density measurements, Debye-Scherrer X-ray diffraction techniques, electron replication microscopy, and electron scanning microscopy. Isothermal treatment at 450°C for 9 hours produces structural ordering in quenched K₂Mg₅Si₈O₂₀F₄ glass. Fluorine exerts a significant influence on the transformation temperature; decreasing amounts of fluorine producing increasing transformation temperatures. The crystallizing phase rapidly attains a limiting particle size and …

The Damage Assessment Of Thermally Shocked High Density, High Purity Aluminum Oxide, John H. Ainsworth

Doctoral Dissertations

"The traditional approach to thermal shock testing in brittle materials has been to determine the temperature difference required to nucleate cracks in these materials. Recent work has indicated that the degree of damage after crack nucleation should be an additional consideration. The degree of damage resulting from cooling thermal shocks has been the primary consideration of the present work. Test specimens of two geometries: long, solid rods and short, solid cylinders were quenched from selected temperatures into ice water. The degree of damage was determined through strength measurements and sonic damping analysis. Initial damage occurred at a temperature difference above …

Optical Reflectance Spectra Of Chromium (Iii) In Mgo-Ss, Thomas Spencer Montgomery

Doctoral Dissertations

"The valence state and coordination site of the transition-metal ion, chromium, was investigated in a MgO host lattice. The chromium ion incorporated into poly-crystalline MgO by quenching from elevated temperatures allowed investigation of a single crystalline phase, MgO-solid solution (ss). The chromium ion was confirmed to occur in the trivalent state and to occupy octahedral cation sites in the MgO lattice by the use of optical reflectance spectroscopy. The effect of the concentration of the chromium ion on the crystal field splitting energy, 10 Dq, permitted analysis over a range of Dq/B values. In conjunction, MgO-ss lattice parameters examined as …

Decomposition Of Cr(Oh)₃ To Form Active Cr₂C₃, Timothy A. Clancy

Doctoral Dissertations

"This study was concerned with the sinterability of Cr₂C₃ powders produced by the calcination of a Cr(OH)₃ gel. The decomposition of the gel was investigated by thermogravimetric analysis, X-ray analysis and microscopic examination. Comparison was made between the size of crystallites as determined by X-ray line broadening and the size of aggregated particles as determined by independent means. These lineal measurements were compared to surface area measurements on the calcined powders. The degree of sinterability was judged from the density measurements on Cr₂C₃ pellets fired under air, oxygen and nitrogen atmospheres. Energies of activation of 25 and 20 kilocalories per …

Internal Friction Of Mixed-Alkali Silicate Glasses, James E. Shelby

Doctoral Dissertations

"The mixed alkali effect in silicate glasses was examined from internal friction measurements made over the temperature range from -190 to 500⁰C and at a frequency of 0.4 Hz. Supplemental measurements of the activation energy for the different internal friction peaks, dynamic shear modulus, density, and index of refraction were also made. All measurements were confined to silicate glasses containing mixtures of Li-Na, Li-K, Li-Rb, Li-Cs, Na-K, Na-Rb, Na-Cs, and K-Rb. Rötger's interpretation of the internal friction of mixed-alkali silicate glasses is shown to be incorrect. A previously unreported internal friction peak was observed whenever two different alkali oxides were …

Mechanism Of Siliconizing Of Molybdenum And Tantalum By Vapor Deposition, Gordon Pu Kong Chu

Doctoral Dissertations

"Molybdenum and tantalum were siliconized in an enclosed system by the hydrogen reduction of silicon tetrachloride with induction heating between 900°C and 1450°C.

The siliconizing process was primarily influenced by the gaseous composition, temperature, time, molar flow ratio (SiCl₄/H₂), geometrical shape and ionization charges. The rate of siliconizing, measured as the weight gain by the fused quartz helix balance, generally follows a parabolic law, y = k t^1/2, where y = weight gain, t = time, and k = rate constant. The activation energy is estimated at 21.6 k cal/mole for siliconizing of molybdenum. …

Statistical Analysis Of Fracture Stresses Of Triaxial Porcelain Bodies, Robert E. Moore

Doctoral Dissertations

"Triaxial porcelain bodies containing various forms of silica, quartz, cristobalite and fused silica, were strength tested in bending. Significance tests were employed to discern real differences in the strength sample statistics caused by the various forms of silica. Firings were performed at three temperature levels. The differences in strength sample statistics were correlated to the microstructures of these silica porcelains.

A triaxial alumina porcelain body was employed as a model brittle solid for a study of the effect of flaw density on mean fracture stress. The flaws were introduced in the form of large diameter (d̄ = 115 microns) rounded …

Phase Relationships In The Quaternary System Lime-Titania-Zirconia-Silica, Robert Martin Gruver

Doctoral Dissertations

"The phase compatibility relationships for the quaternary system lime-titania-zirconia-silica have been determined by a solid-phase-reaction technique.

Preliminary division of the system into Alkemade tetrahedra was based on the phases found in samples by X-ray diffraction analysis. These samples covered the entire volume of the tetrahedron in a systematic fashion. When the quaternary system had been divided into regions or compatible phases, an analytical method was used to calculate the phase composition of each sample. The relative amounts of each phase in a sample determined by X-ray analysis were compared with the calculated quantities, and agreement between the two methods verified …

Nanbo₃ - Batio₃ - Basno₃ Ceramic Dielectrics, William Dean Mckee

Doctoral Dissertations

"A. The Problem.

The purpose of this investigation was to form by ceramic processes a number of compositions in the ternary system NaNbO₃ - BaSnO₃ - BaTiO₃, to determine certain dielectric properties of these, to study them by means or x-ray diffraction, and to determine the extent or correlation possible between the compositional variation of dielectric properties and the x-ray results.

Compositions investigated contained 50 mole percent or less BaSnO₃. Materials and methods of forming were chosen with the intent that the final bodies should be pure oxide compositions as represented in the ternary …

A Study Of The Bonding By Air-Setting Refractory Mortar At Elevated Temperatures, Bhikhubhai Mahadeo Sedalia

Doctoral Dissertations

"The importance of a suitable material for the laying of bricks in furnace and kiln construction has been recognized by the refractory industry for a long time. It is necessary that a strong bond should develop between the bricks to impart strength to the entire construction work. A weak joint would form the weakest link and dangerously weaken the whole structure.

Such being the importance of the bond, the refractory industry has made quite an effort to develop jointing materials which would produce strong bonds. During the last two decades, due to intensive research and development work, many good bonding …

Carbon Monoxide Attack Of Refractories, William A. Frad

Doctoral Dissertations

"The disintegration and failure of fire clay refractories due to the action of carbon monoxide has been studied tor a period at about fifty years. The most important application is in blast furnace refractories. Similar failures due to carbon deposition, involving other gases such as methane, have been noted and less extensively studied. Failures due to the action of gases other than carbon monoxide are beyond the scope of this thesis. Occasional attempts to find some agent to prevent disintegration have been mentioned in the literature. In this study the number of such substances and the results of their action …

An Investigation Of The Characteristics Of High Alumina Refractory Castables, Gajendra Nath Mohanty

Doctoral Dissertations

"Refractory castables or concretes, a comparatively new member of the refractories family, are an admixture of highly aluminous cements and graded refractory aggregates, blended in predetermined proportions very much like structural concrete. The refractory aggregates must contain a large amount of fines contrary to the requirements of ordinary concrete. Unlike the Portland cements, which are mainly combinations of calcium silicates, the highly aluminous cements are predominantly calcium aluminates. They are comparatively of a refractory natures, having the hydraulic setting property combined also with high early strength. The discovery of the fact that these refractory concretes could be cast, in situ, …

Determination Of Progressive Corrosion Of Clay Flux Blocks, Ved Prakash Maheshwary

Doctoral Dissertations

"The Problem. Corrosion of refractories by molten corrosive liquids like molten slags and glasses is of general occurrence in those parts of the furnaces where they come in contact with the liquids. The life of a furnace generally depends upon the progressive rate of corrosion of the refractories by the slags and glasses. There have been various methods used by the investigators to ascertain the useful life of a refractory product before its use in the furnaces, but the problem is so complex that even after decades of research work by the research engineers and technologists a satisfactory and easy …

A Study Of Relative Ionic Mobility Of Alkali Ions In Dilute Alkali-Boron Trioxide Glasses As Deduced From Space Charge Considerations, Theodore J. Planje

Doctoral Dissertations

"The extensive investigations in the past have conclusively established that the alkali ions are responsible for the electrical conductivity of glass in both the brittle and viscous states; however, with the exception of one investigation in the brittle state, little consideration has been given to determination of the mobility of the alkali ion in such glassy systems. A review of the literature pertaining to the electrical conductivity of glass is presented.

A method, based on the rate of development of the ionic space charge responsible for polarization of conductivity cell employing direct current voltages, is proposed as a means for …

A Study Of The Gelation Of Air-Setting Refractory Mortars, James Irving Mueller

Doctoral Dissertations

"Three basic mortar formulae were used in this investigation, each mix having some different materials present and each having its own gelling characteristics. The study was directed along the theory that the dry materials used play an important part in the hardening. Certain admixtures were tested and several were found to improve the workability after storage. The presence of additional sodium ions in the mortar was found to be helpful in overcoming the gelation but these tended to lower the refractoriness of the mortar.

A study was made of the base exchange capacities of the dry materials and the material …

A Study Of The Flow Properties Of Concentrated Clay-Water Mixtures, William Joseph Smothers

Doctoral Dissertations

"The study of flow properties of many substances is of prime importance in varied industries. The ceramic industry is mainly concerned with these measurements on a relatively stiff ceramic body, i.e., one which contains only enough water to retain its shape after the deforming force is relieved.

Various types of instruments have been devised to measure flow properties in the so-called "true plastic range." Since the primary measurements were made on instruments of the transpiration type to devise the laws of viscous and plastic flow, it was felt that an instrument employing the flow of the plastic material through an …