Materials Science and Engineering Commons^™

Mechanical Behavior Of Additively Manufactured Ti-6al-4v Eli Parts: Effects Of Laser Parameter Selection, Samuel Lopez

UNF Graduate Theses and Dissertations

Additive manufacturing (AM) of TI-6AL‑4V Extra‑Low Interstitial (ELI) enables complex geometries for fatigue‑critical medical device applications, yet fatigue performance remains sensitive to process‑induced defects. This work investigates the effect of laser process parameter selection on the microstructure, mechanical properties, and fatigue behavior of TI- 6AL‑4V ELI fabricated via laser powder bed fusion (L‑PBF) using a Renishaw RenAM system. The influence of laser parameters was isolated by holding powder chemistry, build orientation, scan strategy, sub‑transus annealing, and post‑processing constant between a non‑optimized baseline and an optimized parameter set selected based on tensile performance.

Optical microscopy showed the optimized condition exhibited improved …

Development Of A Flexible In Vitro Model System For Studying Biomineralization In Humans And Marine Organisms, Reed J. Harper

UNF Graduate Theses and Dissertations

Biomineralization is a process where cells control the supersaturation of ions and spatiotemporal deposition of numerous proteins to guide biomineralization, resulting in hard mineralized tissues with complex structures and novel properties. The mechanisms of this process are not well understood but key components have been identified as critical for biomineralization to occur. The cellular expression of intrinsically disordered proteins (IDPs) and the subsequent post-translational modification (PTM) play a role in stabilization of mineral precursors, control of morphology and growth, phase/polymorph selection, and composition of mineral formed. Currently in vitro model systems use either synthetic polymers, native proteins extracted from mineralized …

Towards All-Epitaxial Josephson Junctions With High-Temperature Superconductors, Daniela Amalfi Ojeda

UNF Graduate Theses and Dissertations

Josephson junctions are fundamental components of superconducting electronics. Although junctions based on conventional superconductors are well established, reproducible devices based on high-temperature superconductors remain challenging. This work investigates the growth, fabrication, and electrical characterization of all-epitaxial DyBa₂Cu₃O₇₋ₓ (DBCO) /SrTiO₃ (STO) /DBCO trilayer heterostructures for potential Josephson junction applications. An initial optimization of YBa₂Cu₃O₇₋ₓ (YBCO) growth produced reproducible films with a zero-resistance critical temperature ( ) of K and a maximum  of 89 K. These growth conditions were adapted to DBCO, resulting in reproducible superconducting films with values of approximately 80 K. DBCO/STO/DBCO trilayers were grown by molecular beam epitaxy and …

Thermomechanical Modeling Of Transpiration Surfaces For Hypersonic Propulsion, Spencer D. Smith

Graduate Studies Theses and Dissertations 2026

Hypersonic flight vehicles are a promising form of high speed passenger transport and efficient space access architectures. However, they are fundamentally a thermally limited technology. High heat fluxes exceeding 10 MW/m2 and gas temperatures between 3000-4000K can be found both within the engine, and on the outer surface. Current conventional engineering materials are non-viable at these conditions. In order to make these materials viable, active cooling strategies could be utilized. One particularly promising type is transpiration cooling, where a coolant is diffused through a porous surface. Although researched heavily in the 1960s, adoption is still minimal. Part of the reason …

Bowtie Antenna-Coupled Bi₂Te₃–Sb₂Te₃ Thermoelectric Detector For Millimeter-Wave Radiation, Rumana Zahir

Graduate Studies Theses and Dissertations 2026

We explore the development of antenna-coupled thermoelectric detectors for long-wavelength radiation using sputtered bismuth telluride (Bi₂Te₃) and antimony telluride (Sb₂Te₃) thin films. Detection in the infrared, millimeter-wave, and terahertz regimes is critical for sensing, imaging, and energy applications; however, many existing detectors rely on cryogenic operation, exhibit narrow spectral response, or require complex material systems. In this work, we investigate the feasibility of reliable, room-temperature long-wavelength detection using microfabricated thermoelectric thin films integrated with antenna structures. A systematic full-factorial experimental approach was employed to determine how sputtering parameters and post-deposition annealing influence …

Machine Learning Modeling Of In-Situ Effective Thermal Conductivities And Ablation Behaviors Of Ceramic Matrix Composites Under Hydrogen Combustion Environments For Gas Turbine Engines, Jayanta Bhusan Deb

Graduate Studies Theses and Dissertations 2026

Through the integration of experimental characterization, machine learning, deep learning, numerical modeling, and physics-informed artificial intelligence, this dissertation explores the thermal performance of polymer-derived ceramic matrix composites (CMCs) for hydrogen combustion environments. The polymer infiltration and pyrolysis (PIP) process was used to create Yttria-stabilized zirconia (YSZ)-fiber-reinforced ceramic matrix composites, which were then experimentally assessed under hydrogen torch and hydrogen combustion conditions typical of next-generation gas turbine and aerospace propulsion systems. Front- and back-surface temperature measurements were used to continually monitor thermal reactions, and post-test microstructural characterization and numerical simulations were carried out to evaluate material integrity and heat-transfer behavior. To …

Optically-Pumped Semiconductor Optical Amplifiers, Dhruvkumar Desai

Graduate Studies Theses and Dissertations 2026

Semiconductor optical amplifiers (SOAs) offer a low-cost, compact solution for power amplification needs in an optical communication system compared with the dominant erbium-doped fiber amplifiers (EDFAs). They can also provide a wide gain bandwidth. However, conventional electrically-pumped SOAs suffer from larger noise figures, low saturation power, and polarization dependence, in comparison with EDFAs. We propose an optically-pumped SOA (OP-SOA) that will maintain the benefits of conventional SOAs while closing the gaps in other amplifier performance metrics. The underlying reasons for optical pumping are twofold. First, optical pumping allows higher carrier injection and thus "population inversion." Second, optical pumping decouples carrier …

Study On Fracture Toughness Under Different Modes Through Continuum Damage Mechanics Based Fracture Locus, Yeting Sun

Graduate Studies Theses and Dissertations 2026

Traditional elastic-plastic fracture mechanics (EPFM) relies on crack-tip analysis, whereas continuum damage mechanics (CDM) is typically calibrated from uncracked bodies. This dissertation aims to bridge the gap between these two fundamental branches by explicitly linking fracture toughness with ductile damage models. Based on the assumptions regarding Mode I crack deformation, analytical solutions are derived to establish a novel relationship among Mode I fracture toughness, CDM-based ductile fracture strain, and material strain hardening capability. This theoretical framework is subsequently extended to encompass Mode II and Mode III loading conditions. To validate the proposed relationships, finite element (FE) models are developed in …

Advanced Ysz/Si(B)Cn And Bnnt/Si(B)Cn Ceramics Matrix Composites For Extreme Environments In Hydrogen Combustion, Yiting Wang

Graduate Studies Theses and Dissertations 2026

The growing demand for carbon-neutral energy conversion has accelerated the development of hydrogen-fueled gas turbine systems, which operate at significantly higher temperatures and more chemically aggressive environments than conventional natural gas turbines. To meet these stringent requirements, ceramic matrix composite (CMC) materials consisting of yttria-stabilized zirconia (YSZ) fiber reinforced Si(B)CN ceramic matrix were developed. To further enhance in-plane heat dissipation, thermal stability, thermal shock resistance, and thermal cycling performance, a Si(B)CN/Boron Nitride Nanotubes (BNNT) nanocomposite coating was incorporated onto the YSZ/Si(B)CN composites. Microstructural characterization confirmed the formation of a continuous Si(B)CN ceramic matrix reinforced with uniformly distributed BNNTs. The resulting …

First-Principles Insights Into Electronic And Magnetic Structure At Hybrid Interfaces And Low-Dimensional Materials And Reaction On Surfaces, Bushra Ashraf

Graduate Studies Theses and Dissertations 2026

Low-dimensional materials and transition metal surfaces/interfaces provide complementary platforms for understanding how dimensionality, symmetry, spin–orbit coupling (SOC), and interfacial charge transfer/hybridization jointly control electronic structure, emergent magnetism, and surface reactivity. Using first-principles modeling with experimental comparisons, this work aims to establish interfacial structure–property relationships across low-dimensional systems.

Strained Pd adlayers on 2H-MoS₂(0001) provide a controlled platform to separate strain-driven exchange from interface-induced quenching in an itinerant d-electron metal. Although expansive strain promotes magnetism in free-standing Pd, strong Pd–MoS₂ hybridization and charge transfer suppress the monolayer moment and leave a narrow thickness window where magnetism re-emerges in …

Investigation Of Exotic Phenomena In Topological Quantum Materials, Iftakhar Bin Elius

Graduate Studies Theses and Dissertations 2026

he First Quantum Revolution established quantum mechanics as the foundation of modern physics, enabling transformative technologies such as semiconductors, lasers, and transistors through prin-ciples of quantization, wave-particle duality, and uncertainty. The ongoing Second Quantum Rev-olution harnesses entanglement, superposition, and coherence to advance quantum computation, communication, simulation, and sensing. Central to this endeavor is the study of quantum mate-rials hosting novel electronic structures and emergent phases, including topological insulators and Dirac, Weyl, and nodal-line semimetals. In this thesis, using angle-resolved photoemission spec-troscopy (ARPES), transport measurements, and density functional theory (DFT) calculations, we investigate three classes of materials: (i) magnetic topological semimetals, …

A Framework For Optimizing Creep Model Parameters From Conventional And Accelerated Creep Tests, William D. Day

Graduate Studies Theses and Dissertations 2026

The demand for efficiency in power generation and propulsion requires higher firing temperatures and reduced cooling air consumption which raises metal temperatures. This makes simplistic creep evaluations, such as Larson-Miller and Orr-Sherby-Dorn parameters, inadequate. Finite element analysis (FEA) must simulate primary and secondary creep, predict failure, and provide design guidance. Gas turbine components, expected to last over 100,000 hours, often require extrapolation of limited test data for new materials. It is essential that robust creep simulations be developed efficiently, accurately, and effectively use limited test data.

This dissertation describes an optimized framework for efficient creep testing and rapid construction of …

Processing, Characterization And Performance Of Ceramic Liners For Hydrogen Gas Turbine Engines, Fahim Faysal

Graduate Studies Theses and Dissertations 2026

Advanced ceramics and ceramic matrix composites (CMCs) are known for their endurance at high temperatures. This study investigated the fabrication and testing of two material systems: silicon carbide nitride (SiCN) reinforced with yttria-stabilized zirconia (YSZ) fiber manufactured through polymer infiltration and pyrolysis (PIP), and 3D-printed alumina (Al₂O₃) ceramics. The CMC thermal stability at high temperatures was explored through a hydrogen torch test. The CMC surface could withstand a temperature of 1,400°C for 10 minutes during the torch test. Furthermore, the internal surface of a hydrogen combustion chamber was coated with CMC to assess its applicability as a protective barrier against …

Aqueous Iron Electrowinning: From Electrolyte Engineering To The Unexplored Potential Of Acetate Systems, Chodwell N. Verenga

Dissertations, Master's Theses and Master's Reports

Iron electrowinning and electrodeposition sit at the intersection of classical metallurgy and developing sustainable manufacturing. With the iron and steel industry responsible for 7 - 9% of global CO₂ emissions, low-temperature electrochemical pathways for iron production have garnered significant research interest. This review examines the fundamental electrochemical principles governing iron deposition, the thermodynamic constraints imposed by the iron-water system, and the kinetic challenges posed by the parasitic hydrogen evolution reaction (HER). The three key electrolyte systems are objectively evaluated: acidic sulfate and chloride electrolytes, alkaline suspension electrolytes and water-in-salt electrolytes. Their operating parameters, faradaic efficiencies, energy consumption and deposit characteristics …

Zirconium Carbide Based Materials For Extreme Aerospace Environments, Nathaniel Hyman Blatt

Doctoral Dissertations

This research focuses on the processing and properties of zirconium carbide-based materials to promote their use in extreme environment aerospace applications, including nuclear thermal propulsion and hyper sonics. Several carbide systems including ZrC, ZrC-Mo cermets, (Zr, Nb)C, and a high entropy carbide were developed. The ZrC-Mo cermet was studied extensively to understand the effect of starting carbide grain size on the final microstructure, composition, elastic moduli, hardness, fracture toughness, room and elevated temperature flexural strength, thermal diffusivity, electrical resistivity, thermal expansion coefficient, and thermal conductivity. It was shown that heat transport in the cermets was dominated by the ZrC phase …

Investigations In Hydrogen Ironmaking, Joseph William Govro

Doctoral Dissertations

The purpose of this research is to contribute to the Grid Interactive Steelmaking with Hydrogen (GISH) project. This research investigates the viability of both producing and melting Direct-Reduced Iron (DRI) utilizing hydrogen. Conventional CO reduced DRI will be referred to as “C-DRI” and DRI produced using hydrogen gas will be referred to as “H-DRI”.

An H-DRI pilot plant was constructed in Golden Colorado. The pilot plant was commissioned and successfully operated four campaigns. Process improvements were made throughout the campaigns and the process was optimized. In addition to running the pilot plant in a pure hydrogen condition, the pilot plant …

Strontium Titanate For Capacitor And Energy Storage Applications At Cryogenic Temperatures, Hung Trinh

Doctoral Dissertations

This study investigates the dielectric properties of single crystal and ceramic strontium titanate (SrTiO₃) for cryogenic capacitor applications from room temperature to 4 K. Permittivity (k) and loss tangent are dependent on temperature, frequency, mechanical stress, and applied DC electric field. Accordingly, the dielectric constant and loss tangent were measured at various frequencies and DC bias levels. Loss tangent data are also presented as equivalent series resistance (ESR). For single crystal SrTiO₃, an impurity level of ≈500 ppm barium resulted in an increase of the maximum permittivity to approximately 50,000 at 6 K. This relatively high …

Critical Parameters Controlling Oxide Scale Formation And Hydro-Descaling Efficiency During Steelmaking, Tochukwu Princewill Ojiako

Doctoral Dissertations

In modern steelmaking, cast slabs are exposed to high-temperature oxidizing environments during secondary cooling, reheating, and hot rolling, resulting in the formation of multilayer oxide scales on the steel surface. These scales interact with mold-flux residues originating from the casting process (CC). The morphology, chemistry, and adhesion of oxide scale strongly influence its removability during high-pressure hydraulic descaling and ultimately determine the surface quality of hot-rolled products. However, the mechanistic relationship between oxide scale evolution, scale-steel interfacial structure, and hydraulic descaling performance remains poorly understood.

This dissertation investigates oxide scale formation, modification, and removal in low-carbon thin-slab steels produced by …

Investigating The Effects Of Pressure On Fe And Co Intercalated 2h-Tas2 Through First-Principle Calculations, Ronald E. Putnam Jr.

UNF Graduate Theses and Dissertations

Using first-principles methods, we investigate the effects of applied isotropic pressure on the electronic and magnetic properties of intercalated Fe1/3TaS2 and Co1/3TaS2. Fe1/3TaS2 has been shown to be a ferromagnet that undergoes structural and magnetic phase transitions under applied pressure. The magnetic phase transitions are observed to be linked to the structural shift, and a mixture of magnetic phase states is present between 3 GPa and 6 GPa. Co1/3TaS2 was found to be antiferromagnetic, as confirmed by experimental work. One- and two-unit-cell systems of Co1/3TaS2 are analyzed, both showing band splitting that disappears under pressure. The application of pressure forces …

The Efficacy Of Hybrid Manufacturing For High Stress Automotive Parts, Logan Trimmer

Harrisburg University Other Works

Presentation covering the broad strokes of the project. The goal was to prove the viability of hybrid/additive manufacturing for high stress automotive applications. This project focused on recreating a piston from an old engine to examine if hybrid manufacturing could be used for such applications. On a small scale, hybrid manufacturing was able to be more cost effective if the costs of the equipment and electricity were ignored. The decision to ignore those costs came from the inability to find accurate prices for industrial casting.

The Efficacy Of Hybrid Manufacturing For High Stress Automotive Components, Logan Trimmer

Harrisburg University Other Works

The goal of this research was to establish the viability of using hybrid manufacturing for automotive applications. By verifying that high-stress components can be created, it can be assumed that any other lower stress part could be made to match the strength requirements. A limiting factor of adoption for hybrid manufacturing is how new the technology is. Studies on time and cost were performed allowing for comparisons with traditional manufacturing technologies (casting, forging, milling) used in automotive applications. This research utilized a Haas Automation UMC750 5-axis CNC mill with a Meltio laser wire direct energy deposition attachment. Fusion 360 was …

Waveguide-Assisted Single-Mode Fiber Bragg Gratings In A Highly Multimode Coreless Fiber Via Femtosecond Laser Inscription For Extreme Temperature Quasi-Distributed Thermal Sensing, Farhan Mumtaz, Koustav Dey, Bohong Zhang, Jeffrey D. Smith, Ronald J. O'Malley, Jie Huang

Electrical and Computer Engineering Faculty Research & Creative Works

This research reports a potential quasi-distributed thermal mapping optical sensing system for extreme temperatures, leveraging femtosecond (fs) laser inscribed single-mode fiber Bragg gratings (FBGs) and a waveguide within coreless, highly multimode optical fiber, resulting in a single-mode structure. Unlike doped single-mode fibers, coreless fibers composed of silica rods prevent issues associated with dopant migration and ensure data accuracy. The strategic placement of point-by-point FBGs in a cascaded formation on the fs-laser inscribed waveguide facilitates localized multipoint sensing. The long-term stability of the proposed waveguide-assisted FBG system was assessed over 24 hours at elevated temperatures (1000°C), showing no hysteresis during heating …

Distributed Temperature Sensing In The Spray-Cooled Shell Of A 150-Ton Dc Electric Arc Furnace Using Brillouin Optical Fiber Technology, Farhan Mumtaz, Yeshwanth Reddy Mekala, Koustav Dey, Rony Kumer Saha, Ogbole Collins Inalegwu, Manoj Kumar Pullagura, Bohong Zhang, Muhammad Roman, Nicholas Dionise, Zane Voss, Jeffrey D. Smith, Ronald J. O'Malley, Rex E. Gerald, Jie Huang

Electrical and Computer Engineering Faculty Research & Creative Works

This paper presents the deployment and validation of a Brillouin - distributed temperature sensing (DTS) system for real-time thermal monitoring of the spray-cooled upper shell of a 150-ton direct current Electric Arc Furnace (DC EAF) at Big River Steel Plant, Osceola, AR, USA. A four-channel Brillouin DTS system from OZ Optics was employed, with one active channel instrumented using an in-house-fabricated Brillouin scattering-depressed single-mode optical fiber (SMF28e+). The 60 m optical fiber sensor was fabricated, with 20 m allocated for thermal measurement and 40 m used as lead-in fiber to isolate the interrogator from the furnace environment. The fiber was …

Osmotic Dilators Vs. Foley Balloons: Bayesian Secondary Analyses Of The Dilafol Trial, Antonio F. Saad, Elenir B. C. Avritscher, Claudia Pedroza, Xiao Han, George R. Saade

Department of Obstetrics & Gynecology Faculty Publications

Background: Dilapan-S, a synthetic osmotic dilator used for pre-induction cervical ripening, has proven to be as effective as the Foley balloon in terms of vaginal versus cesarean delivery and has been associated with increased patient satisfaction. Nevertheless, its ability to lower cesarean rates and its cost-effectiveness remain poorly studied.

Objectives: To estimate the likelihood that synthetic osmotic dilators reduce cesarean deliveries and to evaluate their health system costs (2026 US$) and incremental cost-effectiveness compared to the Foley balloon during cervical ripening.

Study Design: Secondary Bayesian analyses were conducted using data from the single-center DILAFOL randomized controlled trial, which enrolled 419 …

Modulation Of Prussian Blue Redox Signaling By Molecular Imprinting For Reagent-Free Electrochemical Detection Of Emtricitabine, Abdellatif Ait Lahcen, Gymama Slaughter

Center for Bioelectronics Publications

Reagent-free electrochemical sensors offer significant benefits for rapid, affordable point-of-care drug testing. In this study, we introduce a novel, reagent-free electrochemical sensor based on a molecularly imprinted polymer (MIP) specifically designed for the selective detection of Emtricitabine (FTC), a common antiretroviral used in HIV therapy. The sensor uses laser-induced graphene (LIG) electrodes, renowned for their high conductivity and porosity, ideal for electrochemical sensing. To enable reagent-free operation, the LIG surface was electrochemically coated with Prussian Blue, serving as a redox-active layer. Next, an MIP-PPy film was electropolymerized onto the Prussian Blue surface in the presence of FTC as a template, …

Nanofibrous Materials And Nanoparticles For Combating Antimicrobial Resistance: Synthesis, Integration, And Translational Perspectives, Rewati Raman Ujjwal, Ashish Dilip Sutar, Rahul Shukla, Gymama Slaughter

Center for Bioelectronics Publications

Antimicrobial resistance (AMR) is a major global health challenge driven by mechanisms such as biofilm formation, efflux pumps, and genetic mutations. Nanoparticulate and fibrous materials have emerged as promising strategies to overcome these limitations through multimodal antimicrobial action and controlled drug delivery. This review highlights recent advances in electrospun nanofibrous systems, including natural and synthetic polymer-based scaffolds, stimuli-responsive nanofibers, and functionalized patches. Nanoparticle-loaded nanofiber systems demonstrate enhanced performance, including bacterial eradication, sustained drug release, and significant biofilm disruption. Multifunctional systems combining antimicrobial, antioxidant, and immunomodulatory properties further show synergism. Emerging innovations, such as piezoelectric and smart sensing systems, enable self-powered …

Linker-Free Gold-Sputtered Tapered Optical Fiber Plasmonic Sensors For High-Sensitivity Refractive Index Detection In Microfluidic Platforms, Erem Ujah, Gymama Slaughter

Center for Bioelectronics Publications

Gold-sputtered tapered optical fiber (Au-TOF) sensors were developed for high-sensitivity refractive-index (RI) detection using aqueous glucose standards spanning 1.33–1.41 RIU (0–50% w/v). The sensors were fabricated using a reproducible workflow combining flame-brushing tapering, plasma surface preparation, and rotational magnetron sputtering, enabling azimuthally uniform gold coatings without the use of thiol or sulfur linker chemistries. Two sputtering durations (24 s and 30 s) were investigated to examine thickness-dependent plasmonic coupling and sensing performance. Optical measurements were conducted using a broadband supercontinuum source and compact spectrometer within a 20 µL microfluidic sensing chamber. Increasing glucose concentration produced a monotonic decrease in transmission …

Engineering Electrospun Pvdf Nanofibers For Next-Generation Wearable Bioelectronics, Reshmi Banerjee, Gymama Slaughter

Center for Bioelectronics Publications

Electrospun poly(vinylidene fluoride) (PVDF) and P(VDF-TrFE) nanofibers offer a mechanically flexible, high-surface-area platform for wearable bioelectronics, including piezoelectric sensing and self-powered operation. This review establishes a process–structure–property–performance framework for engineering electrospun PVDF- and P(VDF-TrFE)-based wearable systems. Relationships amongst precursor composition, electrospinning parameters, fiber morphology and alignment, crystalline phase formation, dipole orientation, and device-level piezoelectric performance are examined. Electrospinning is compared with other established fabrication methods including solution casting, spin coating, melt processing, phase inversion, and printing in terms of electroactive β-phase fraction, flexibility, scalability, manufacturing complexity, cost, and wearable-device suitability. Device architectures and performance are evaluated across pressure and strain …

Ion-Imprinted Polymer-Based Sensors For Toxic Metal-Ion Detection In Water: Coordination Chemistry, Transduction Strategies, And Environmental Applications, Ghita Yammouri, Gymama Slaughter

Center for Bioelectronics Publications

Toxic metal contamination in aquatic environments remains a persistent threat to human health and ecosystems. Yet, the high cost, infrastructure demands, and centralized nature of conventional analytical methods constrain routine monitoring. Ion-imprinted polymers (IIPs), a subclass of molecularly imprinted polymers, have emerged as promising synthetic recognition materials for metal-ion sensing because they generate coordination-defined binding sites with high selectivity, chemical stability, low cost, and reusability. This review summarizes recent advances in Ion-imprinted polymer (IIP)-based sensing technologies for toxic metal-ion detection in water from 2016 to 2026. It examines the fundamental recognition chemistry of IIPs, major synthesis strategies used to generate …