Materials Science and Engineering Commons^™

Seeding Effects Of Submicron Caal-No3 Ldh Particles On The Hydration And Properties Of Portland Cement And Sulfoaluminate Cement Pastes, Sukanta K. Mondal, Monday Uchenna Okoronkwo

Chemical and Biochemical Engineering Faculty Research & Creative Works

Layered double hydroxide (LDH) is reported to improve the durability of concretes, primarily due to its ability to exchange anionic species, including chloride, which is implicated in corrosion-driven durability issues. However, there is no comprehensive study investigating the effect of LDH on the properties of different cement systems at both early and mature ages. in this study, the early age and mature age properties of Portland cement (OPC) and calcium sulfoaluminate (CSA) cement pastes seeded with submicron-sized calcium aluminum-NO3 LDH (CaAl-NO3 LDH) were investigated. the effects of the 1–5%mass dosage of LDH on the hydration of both cement systems were …

Research On 3d Printing Resin Exposure Properties And Its Application On Centrifugal Microfluidic Platform Based On Fluorescence Detection, Zheng Qiao

LSU Doctoral Dissertations

This dissertation encapsulates significant advancements in the field of SLA 3D printing and centrifugal microfluidics. Central to the research is the development of a novel mathematical model for predicting trapped resin thickness in SLA 3D printing, a groundbreaking contribution that addresses a critical aspect of printing intricate structures. This model, the first to establish a mathematical relationship for resin thickness, is rooted in a comprehensive study of the resin curing process. The research leverages the concept of 'critical dosage' for resin curing, leading to a more refined and theoretically grounded approach for calculating curing thickness. Experimentation further validates the model, …

Quasi-Static Compression Performance Of Three Subscale Origami-Inspired Carbon Fiber Reinforced Polymer, Chase Mortensen

Student Research Symposium

Sandwich-structured composites are made of a lightweight core material between two thin composite panels. Variants of the Ori-Miura folding pattern have been investigated and compared to both the traditional Miura folding pattern (Fig. 1) and the more commonly used core design, the honeycomb. While the honeycomb design is favored over the Miura folding pattern and its variants due to its simple shape and better performance in compression, honeycomb cores also present drawbacks that are detrimental to the integrity of the sandwich structure. These drawbacks include, but are not limited to:

• Honeycomb cores consist of closed channels trapping moisture and heat. …

Thermo-Gravimetric Analysis Of Variables Of Oxidization, Clark Nguyen, Mario F. Buchely

Undergraduate Research Conference at Missouri S&T

Oxidation phenomena play a critical role in high temperature metallurgical processing and the performance during life cycle of components made of both high and low alloy steels. Therefore, the development of a precise experimental methodology to quantify oxidation processes is critically important. This report summarizes my experimental study of the oxidation behavior of high and low alloy steel, including kinetics of surface oxide layer formation and spallation. The focus of study was in determining the complex interactions between alloying elements in steel matrix and oxidation environment, composition and surface morphology of formed oxides. This report will also explore how the …

The Aerodynamic Levitator Project, Noah Brown

Undergraduate Research Conference at Missouri S&T

After the development and successful demonstration of a hyperbaric aerodynamic levitator, work to redesign the nozzle was proposed for increasing levitation height and stability. The goal of this eight-week summer research project was to create a CFD model to aid in the optimization of this nozzle. This was to be accomplished by using ANSYS Fluent to first replicate experimental data found in a research paper to assess its validity. Next, the model was to be modified for use on the levitator project and then used to analyze the current nozzle design. Afterwards, Steps will be taken to make alterations to …

Thermogravimetric Analysis Of High & Low Alloy Steel, Clark Nguyen

Undergraduate Research Conference at Missouri S&T

Oxidation phenomena play a critical role in high temperature metallurgical processing and the performance during life cycle of components made of both high and low alloy steels. Therefore, the development of a precise experimental methodology to quantify oxidation processes is critically important. This report summarizes my experimental study of the oxidation behavior of high and low alloy steel, including kinetics of surface oxide layer formation and spallation. The focus of study was in determining the complex interactions between alloying elements in steel matrix and oxidation environment, composition and surface morphology of formed oxides. This report will also explore how the …

Synergy Between Ca2+ And High Ionic Field-Strength Cations During The Corrosion Of Alkali Aluminoborosilicate Glasses In Hyper-Alkaline Media, Qianhui Qin, Nicholas Stone-Weiss, Nian Shi, Pinaki Mukherjee, Jinjun Ren, Ashutosh Goel

Michigan Tech Publications

One major factor impeding the design of nuclear waste glasses with enhanced waste loadings is our insufficient understanding of their composition–structure–durability relationships, specifically in the environments the waste form is expected to encounter in a geological repository. In particular, the high field-strength cations (HFSCs) are an integral component of most waste streams. However, their impact on the long-term performance of the glassy waste form remains mostly undeciphered. In this context, the present study aims to understand the impact of some HFSCs (i.e., Nb5+, Zr4+, Ti4+, and La3+) on the dissolution behavior of alkali/alkaline-earth aluminoborosilicate-based model nuclear waste glasses in hyper-alkaline …

Thermal Frontal Polymerization – Applications In Coatings And Composites, Maria Martinez

LSU Doctoral Dissertations

Thermal frontal polymerization has long been used as a method to cure composites and coatings. However, this is the first time these applications have been used without the use of a catalyst, for the case of composites and coatings.

Chapter 2 discusses how to optimize cure-on-demand, thin layer coatings, using frontal polymerization. Previously, for the use of curing thin layer coating using thermal FP, it was known to just make the formulation viscous enough, as this would prevent premature quenching caused by heat loss. It was discovered that for a given layer thickness, a minimum viscosity and initiator concentration were …

Globular Protein For Surface Modification Of Cellulosecontaining Materials, Nodira Saydaliyeva

Technical science and innovation

The purpose of this work is the chemical modification of cotton fabrics with natural globular protein. Modification was carried out in the process of finishing cotton fabrics, after decoction and bleaching in a continuous mode. The effect of modification on the strength, protein content and functional groups of cotton fabric has been studied. According to the results obtained using the AUTOGRAPH AGS-N machine, it was found that the modification of cotton fabrics with a solution of globular protein increases the strength of the treated fabrics, depending on the concentration of the modifier and the temperature regime. Treatment with a highly …

Uncertainty Analysis In Machine Learning Models, Ayorinde E. Olatunde, Weiqi Yue, Pawan K. Tripathi, Roger H. French, Anirban Mondal

Faculty Scholarship

No abstract provided.

A Guide To Fifty Years Of Research At Montana Tech: Part 3-Decontamination Of Ratioactively Contaminated Steel By Melt Refining/Slagging Processing, Larry G. Twidwell, Samuel A. Worcester

Metallurgy

This presentation includes a discussion of the research conducted at Montana Tech in the Department of Metallurgical and Materials Engineering. The discussion is focused on Decontamination of Radioactively Contaminated Steel by Melt Refining/Slagging. This presentation is based on the research of Master of Science graduate students, industrial and academic colleagues, at the Montana College of Mineral Science and Technology (which morphed to Montana Tech [1977], then to Montana Tech of The University of Montana [2000], then to Montana Technological University [2019]). The referenced work of each of the graduate students in this presentation is gratefully acknowledged. The following summary presentation …

Starfish: A Compact, Biomimetic, And Adaptive Shape Memory Alloy Orbital Debris Remover, Katelyn Branaman

Doctoral Dissertations and Master's Theses

This thesis aims to turn the tides on the orbital debris issue through the fabrication and demonstration of a compact, biomimetic, and adaptive shape memory alloy actuated orbital debris remover. The design, referred to as Starfish, is discussed in detail along with its fabrication process and object capture ability. A hard skeleton crafted from PETG was combined with shape memory alloy wires and extension springs to create a biomimetic structure that operates similar to the human hand, capable of gripping a wide range of objects. Relevant simulations were performed and discussed, the iterative fabrication process used to create each component …

Scalable Fabrication Methods For Energy Devices, Julia Elizabeth Huddy

Dartmouth College Ph.D Dissertations

Emerging energy technologies have the potential to fill gaps in performance and reliability but currently lack the capabilities to do this at a commercial scale. 3D printing has the ability to fabricate engineered lattice structures with broadly tunable surface area and optimal geometries for maximizing electrochemical performance, and perovskite solar cells (PSCs) have the potential to deliver terawatt-scale power via low-cost manufacturing. However, neither of these technologies has yet to achieve fully scalable manufacture. 3D printed energy storage devices lack an understanding of how 3D lattice type influences the specific capacity when employed in supercapacitors, and PSC fabrication is limited …

Testing Of Recycled Polypropylene As A Viable Structural Material (Quarter 2), Isabella Jimenez-Melendrez, Katherine Timbes, Jocelyn Embleton, Tauni Dela Cruz, Zyra Kingston, Emily Byrd, Jacob Stinger

Architectural Engineering

5.25 trillion plastic particles have been found in the oceans each year, 3 million water bottles are consumed each hour, and one million plastic bags are used each minute in the United States of America (Williams). The vast majority of conventional plastics such as polyethylene, polypropylene, polystyrene, and more, are non-biodegradable (Tokiwa). To make matters worse, 70% of this non-biodegradable plastic is discarded into landfills and inevitably makes its way into the environment (Williams,). Plastic products have become vital to the United States economy due to their many uses in the construction, packaging, transportation, and health care industries. However, this …

Longitudinal Solid Polarized Target For Clas12 And Study Of Spin Structure Of Nucleons, Pushpa Pandey

Physics Theses & Dissertations

A suite of experiments measuring target-spin observables in electron-nucleon scattering (dubbed Run Group C) was conducted at Jefferson Lab’s Hall B in Newport News, VA with a new polarized nuclear target known as ‘APOLLO’ (Ammonia Polarized Longitudinally). This innovative target is engineered to seamlessly integrate with the advanced 12 GeV CEBAF (Continuous Electron Beam Accelerator Facility) accelerator and the Hall B CLAS12 (12 GeV CEBAF Large Acceptance Spectrometer) detector array. The ‘APOLLO’ target harnesses the power of Dynamic Nuclear Polarization (DNP) to achieve longitudinal polarization of solid ammonia, thereby creating a net polarization in both protons (NH₃) and …

Shorting At Long Duration: Impact Of Extended Discharge Capacity On Battery Solid Electrolytes, Ryan C. Hill, Amanda S. Peretti, Leo J. Small, Erik D. Spoerke, Yang-Tse Cheng

Chemical and Materials Engineering Faculty Publications

Long-duration energy storage (LDES) is critical to a stable, resilient, and decarbonized electric grid. While batteries are emerging as important LDES devices, extended, high-power discharges necessary for cost-competitive LDES present new materials challenges. Focusing on a new generation of low-temperature molten sodium batteries, we explore here unique phenomena related to long-duration discharge through a well-known solid electrolyte, NaSICON. Specifically, molten sodium symmetric cells at 110 ° C were cycled at 0.1 A cm−2 for 1–23 h discharges. Longer discharges led to unstable overpotentials, reduced resistances, and decreased electrolyte strength, caused by massive sodium penetration not observed in shorter duration discharges. …

Quasi-Static And Impact Load Response Of Bfrp-Reinforced Concrete Beams And Post-Terrorist-Attack Sub-Assemblages, José Luis Carrasquillo

Civil & Environmental Engineering Theses & Dissertations

This dissertation presents the outcome of a theoretical and experimental study of Basalt Fiber Reinforced Polymer (BFRP) reinforced concrete beams and post-terrorist-attack subassemblages subjected to either quasi-static or impact load. Both BFRP reinforcement as well as BFRP fabric are used in this investigation. The sub-assemblage consists of an otherwise two-span beam converted to a fixed-end single-span one owing to the loss of a middle column blasted off during the terrorist attack. The simply supported beams are subjected to a midspan quasistatic or an impact load. However, each sub-assemblage is subjected to a quasi-static load up to collapse to simulate the …

Thermo-Elasto-Plastic Stability Of Biaxially Loaded Hollow Rectangular Section Steel Beam-Columns With Applied Torsion, George Adomako Kumi

Civil & Environmental Engineering Theses & Dissertations

Presented herein is an experimental and theoretical study of biaxially loaded hollow rectangular section steel beam-columns with applied torsion at elevated temperatures. The theoretical analysis is based on a system of simultaneous materially nonlinear differential equations of equilibrium for which an iterative semi-analytic solution approach is formulated. Although the primary goal of this research is to study the influence of elevated temperatures on the steel member with the complex loading, rigorous analysis is also conducted of the member at ambient temperature for comparison. The experimental part of the study involves conducting tests on the members at both ambient and high …

Segregation And Heat Treatment Response Of Cast Quench And Partition Steels, Mujeeb Hussain Shaik

Masters Theses

Quench and partition (Q&P) steels have emerged as promising alternatives to traditional quenching and tempering methods, offering a superior balance of strength and ductility due to their unique microstructure of martensite, and retained austenite. This literature review examines the development and optimization of Q&P steels, focusing on their mechanical properties, heat treatment processes, and applications in various industries. This study explores the application and effectiveness of the Quench and Partition (Q&P) heat treatment process on cast steels and examines segregation phenomena in cast medium Mn steels. Medium Mn steels were employed for various Q&P cycles on cast specimens to investigate …

Safety Evaluation Of Hawaii Dot Modified Type A-1 Flared Buried In Backslope Guardrail End Terminal, Sina Changizian

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

The Hawaii Department of Transportation (HDOT) desired to evaluate the crashworthiness of a guardrail end terminal design in which the upstream guardrail anchorage was connected to a block partially buried in a cut slope, known as a “Buried in Backslope” or BIB design. The HDOT BIB system used an upper W-beam with 8-in. deep blockouts attached to W6x9 steel posts and a lower W-beam rubrail located 3 in. below the upper rail. The system used two horizontal flares: 7.4:1 near the upstream anchor block and a 13:1 flare through the ditch.

Critical impact points (CIPs) were identified and recommended for …

Advancements In Characterization Of Ancient Potteries From Southeast Asia: A Review Of Analytical Techniques, Chitnarong Sirisathitkul

Makara Journal of Science

Ancient potteries offer valuable information regarding technological advancements, life dynamics, cultural diversity, and trade routes in the past. Earthenware, stoneware, and porcelain from Southeast Asia have been characterized using several analytical techniques, as reviewed in this article. Fluorescent and diffracted X-rays give rise to elemental and phase compositions, respectively. Examination of molecular bonds requires vibrational spectroscopy, which is useful for the identification of organic materials in ancient potteries. With the advent of portable X-ray fluorescence and Raman spectrometry, on-site analysis of archeological ceramics is now possible. For in-depth analysis, synchrotron light sources can provide new insights into artifacts through X-ray …

Electrospun Nanofiber Technology Based Energy Storage And Biosensor Devices For Wearable Electronics, Bianca Seufert

USF Tampa Graduate Theses and Dissertations

As progress in the field of nanotechnology continues to evolve, it is becoming more and more prevalent to apply this small but powerful technology to portable wearable electronics. The unique scale of such a technology lends its expertise to the investigation of enzymes for biometric related diagnostics or in the development of light weight flexible energy storage devices. Furthermore, as the need for highly precise and durable wearable electronics grows, the next generation of electronics must keep pace with this development in terms of shape, flexibility, functionality, and performance.

The presented research reviews the current state of art of nanofiber …

A Comparison Of Beamforming Characteristics In Isotropic And Composite Plate Structures For Use In Structural Health Monitoring, Sarah Ketchersid

Doctoral Dissertations and Master's Theses

Structural health monitoring in plate-like simple structures using phased array beamsteering of guided Lamb waves is useful in damage detection and evaluation efforts. Lamb waves can be effectively used for beamsteering using a linear array. The experimentation primarily focuses on beamsteering in the aluminum panel, which involves developing a simulation based on extracted data to visualize the dispersion of waves across the panel. By evaluating parameters such as slowness, velocity, and amplitude direction and variation for a specific metallic plate, the wavefront generated by a single wave source can be represented as a function of propagation angle and distance from …

Effect Of Fabrication Parameters On The Ferroelectricity Of Hafnium Zirconium Oxide Films: A Statistical Study, Guillermo A. Salcedo, Ahmad E. Islam, Elizabeth Reichley, Michael Dietz, Christine M. Schubert Kabban, Kevin D. Leedy, Tyson C. Back, Weison Wang, Andrew Green, Timothy S. Wolfe, James M. Sattler

Faculty Publications

Ferroelectricity in hafnium zirconium oxide (Hf_1−xZr_xO₂) and the factors that impact it have been a popular research topic since its discovery in 2011. Although the general trends are known, the interactions between fabrication parameters and their effect on the ferroelectricity of Hf_1−xZr_xO₂ require further investigation. In this paper, we present a statistical study and a model that relates Zr concentration (x), film thickness (t_f), and annealing temperature (T_a) with the remanent polarization (P_r) in tungsten (W)-capped Hf_1−xZr_xO₂. …

Recent Advances In Solar Photo(Electro)Catalytic Nitrogen Fixation, Jun-Bo Ma, Sheng Lin, Zhiqun Lin, Lan Sun, Chang-Jian Lin

Journal of Electrochemistry

Ammonia (NH₃) is an essential chemical in modern society. It is currently produced in industry by the Haber-Bosch process using H₂ and N₂ as reactants in the presence of iron-based catalysts at high-temperature (400–600 ^oC) and extremely highpressure (20–40 MPa) conditions. However, its efficiency is limited to 10% to 15%. At the same time, a large amount of energy is consumed, and CO₂ emission is inevitably. The development of a sustainable, clean, and environmentally friendly energy system represents a key strategy to address energy crisis and environmental pollution, ultimately aiming to achieve carbon neutrality. …

Micropatterning And Functionalization Of Single Layer Graphene: Tuning Its Electron Transport Properties, Miao-Miao Cui, Lian-Huan Han, Lan-Ping Zeng, Jia-Yao Guo, Wei-Ying Song, Chuan Liu, Yuan-Fei Wu, Shi-Yi Luo, Yun-Hua Liu, Dong-Ping Zhan

Journal of Electrochemistry

As a promising 2D material, graphene exhibits excellent physical properties including single-atom-scale thickness and remarkably high charge carrier mobility. However, its semi-metallic nature with a zero bandgap poses challenges for its application in high-performance field-effect transistors (FETs). In order to overcome these limitations, various approaches have been explored to modulate graphene's bandgap, including nanoscale confinement, external field induction, doping, and chemical micropatterning. Nevertheless, the stability and controllability still need to be improved. In this study, we propose a feasible method that combines electrochemical bromination and photolithography to precisely tune the electron transport properties of single layer graphene (SLG). Through this …

Interfacial Magnetism And Anisotropy In Dirac And Weyl Semimetals, Noah Schulz

USF Tampa Graduate Theses and Dissertations

Semimetals have gained intense interest recently due to their exotic magnetic and electronic properties. One of the most widely studied semimetals is graphene, a Dirac semimetal. The utilization of graphene in devices and sensors requires interfacing it with other materials, which may induce potentially strong interfacial effects. Furthermore, graphene alone does not possess magnetic order. Studying the interfacial effects between graphene and magnetic materials is therefore of great importance in the application of graphene to meet modern technological needs. Furthermore, by understanding the fundamental interfacial physics between graphene and magnetic materials, new properties can be unlocked, broadening the possible applications …

Engineering Nanofibers: Laboratory Characterization, Microstructural Analysis, And Image Processing Insights, Sayed Ahmadreza Razian, Mohammad Arjomandi, Kaspars Maleckis

UNO Student Research and Creative Activity Fair

Polymer nanofibers have attracted high interest in a wide array of applications, including biomaterial scaffolding, textiles, sensors, reinforcement in composites, and filtration systems. Many of these applications combine nanofibers into non-woven fabrics for better properties and easier manipulation. The properties and performance of nanofiber-based fabrics are affected by various microstructure parameters, including fiber alignment, diameter, and gap sizes between the nanofibers. These structural parameters can be controlled by adjusting various process parameters during manufacturing process, but the exact process parameter-microstructure relationships vary depending on the polymer system and need to be studied individually. The goal of this study is to …

Machine Learning Prediction Of Photoluminescence In Mos2: Challenges In Data Acquisition And A Solution Via Improved Crystal Synthesis, Ethan Swonger, John Mann, Jared Horstmann, Daniel Yang

Seaver College Research And Scholarly Achievement Symposium

Transition metal dichalcogenides (TMDCs) like molybdenum disulfide (MoS2) possess unique electronic and optical properties, making them promising materials for nanotechnology. Photoluminescence (PL) is a key indicator of MoS2 crystal quality. This study aimed to develop a machine-learning model capable of predicting the peak PL wavelength of single MoS2 crystals based on micrograph analysis. Our limited ability to consistently synthesize high-quality MoS2 crystals hampered our ability to create a large set of training data. The project focus shifted towards improving MoS2 crystal synthesis to generate improved training data. We implemented a novel approach utilizing low-pressure chemical vapor deposition (LPCVD) combined with …

La1-Xsrxcoo3 Perovskite Nanomaterial: Synthesis, Characterization, And Its Biomedical Application, Adhira Tippur, Anyet Shohag, Luke Franco, Ahmed Touhami, Swati Mohan, Mohammed Uddin

Research Symposium

Early cancer detection is paramount for effective treatment and potential cures. This research explores the application of perovskite materials, specifically Sr2+-doped Lanthanum Cobaltite (La1-xSrxCoO3) nanomaterials, in cancer detection, with a focus on rats as an experimental model. The ferroelectric nature of these materials, synthesized through a combination of sol-gel and molten-salt processes, was examined at varying Sr2+ doping levels (1-20 wt%). Rigorous characterization, employing X-ray diffraction and scanning electron microscopy, confirmed the uniform morphology of nano cubes, laying the foundation for subsequent investigations. The magnetic properties of the perovskite nanoparticles were probed, suggesting their potential as a diagnostic tool for …