Materials Science and Engineering Commons^™

Soft Electronics And Sensors For Wearable Healthcare Applications, Li-Wei Lo

McKelvey School of Engineering Graduate Student Theses & Dissertations

Wearable electronics are becoming increasingly essential to personalized medicine by collecting and analyzing massive amounts of biological signals from internal organs, muscles, and blood vessels. Conventional rigid electronics may lead to motion artifacts and errors in collected data due to the mismatches in mechanical properties between human skin. Instead, soft wearable electronics provide a better platform and interface that can form intimate contact and conformably adapt to human skin. In this respect, this thesis focuses on new materials formulation, fabrication, characterization of low-cost, high sensitivity and reliable sensors for wearable health monitoring applications.

More specifically, we have studied the silver …

Contents, Jaka Fajar Fatriansyah

Journal of Materials Exploration and Findings

No abstract provided.

Preface Of Volume 1 Issue 1 On Journal Of Materials Exploration And Findings (Jmef), Jaka Fajar Fatriansyah

Journal of Materials Exploration and Findings

No abstract provided.

The Optimization Of Failure Risk Estimation On The Uniform Corrosion Rate With A Non-Linear Function, Fernanda Hartoyo, Jaka Fajar Fatriansyah, Imam Abdillah Mas'ud, Farhan Rama Digita, Hanna Ovelia, D. Rizal Asral

Journal of Materials Exploration and Findings

Failures in the oil and gas pipeline system are conditions that must be avoided and anticipated because the losses due to the failures can occur at a very high level. Internal corrosion is one of the significant causes of the failures in pipeline systems. In addition, this type of corrosion is due to the high content of carbon dioxide and other corrosive substances in crude oil and natural gas. Therefore, an optimal inspection scheduling system is required to prevent the possibility of pipeline failures due to corrosion and to avoid any overspending on the budget due to excessive inspection scheduling. …

Material Selection Of Below-Knee Leg Prosthetics, Raihan Kenji Rizqillah

Journal of Materials Exploration and Findings

The effort to select the best pylon material, part of below-knee leg prosthetic, has been performed. It begins with function analysis to generate design requirement, which concludes that the objective is to select material that gives proper mechanical properties with lowest weigth and cost. Constraint requirements eliminate unsuitable material. Material indices, a scoring function, are derived from objective with respect to a function, and used for ranking material candidates. Ranking from material indices gives top material candidates of woods. Al alloy, Mg alloy, and ferrous alloy. Further seek of documentation is undertaken by failure analysis, value analysis, fabrication, and environmental …

Investigating Features And Output Correlation Coefficient Of Natural Fiber-Reinforced Poly(Lactic Acid) Biocomposites, Andreas Federico, Siti Norasmah Surip, Wan Nor Raihan Wan Jaafar, Jaka Fajar Fatriansyah, Agrin Febrian Pradana

Journal of Materials Exploration and Findings

Polylactic acid (PLA) material has the potential to be applied in various industrial fields, but this material has shortcomings in terms of mechanical properties, especially mechanical strength, due to brittleness nature of PLA. The manufacture of PLA composite material with the addition of natural fibers as a reinforcing phase is one of the methods to increase the impact strength and maintain the biodegradable properties of the material. However, in theory, there are many factors that affect the mechanical properties of composite materials, thus making the mechanical properties of composites more complex than monolithic materials. The mechanical properties of these composite …

The Effect Of Sample Placement In The Furnace During The Heat Treatment Process Of 7075-T6 Aluminum Alloy On Microstructure, Hardness, And Electrical Conductivity, Donanta Dhaneswara, Hardi Rindharto, Muhammad Syauqi Aqilafif

Journal of Materials Exploration and Findings

This paper reports the effects of sample placement during the heat treatment on the microstructural morphology and mechanical properties of 7075 Al alloy such as hardness value and electrical conductivity. The material was in the formed of Al alloy sheets where samples were machined into a square with dimensions of 1.5 x 1.5 inch. The 7075-T0 Al alloy as samples were given heat treatment by precipitation hardening (aging) at temperature 120°C for 24 hours, so it becomes 7075-T6 Al alloy. Samples were subjected to some mechanical tests and the morphology of the resulting microstructures were characterized by optical microscopy. The …

Effects Of Cyclic Intercritical Annealing On Strength-Ductility Combinations In Medium Manganese Steels, Dawn Van Iderstine

Theses and Dissertations

Intercritically annealed medium manganese steels are a promising third-generation advanced high-strength steel candidate, relying on large fractions of Mn-enriched retained austenite for excellent strength-ductility combinations. The present study proposes a novel cyclic intercritical annealing to promote nucleation and efficient stabilization of austenite in a medium Mn microstructure. Design of the heat treatment is driven by the hypothesis that the distribution of ductile austenite is key in mitigating the strain incompatibility that accelerates failure in these steels. Development and preliminary testing of the heat treatment are first detailed and compared with literature results for equivalent isothermal annealing. The effects of cyclic …

Ferrous Alloy Manufacturing For The Martian Surface Through In-Situ Resource Utilization With Ionic Liquids Harvested Iron And Bosch Process Carbon, Blake C. Stewart

Theses and Dissertations

As research continues for the habitation of the Lunar and Martian surfaces, the need for materials for construction of structural parts, mechanical components, and tools remains as a major milestone. The use of in-situ resource utilization (ISRU) techniques is critical due to the financial, physical, and logistical burdens of sending supplies beyond low-Earth orbit. The Bosch process is currently in development as a life support system at the National Aeronautics and Space Administration’s (NASA) Marshall Space Flight Center (MSFC) to regenerate oxygen (O2) from metabolic carbon dioxide (CO2) with the byproduct of elemental carbon (C). The Bosch process presents a …

Recent Advances In Microwave Synthesis For Photoluminescence And Photocatalysis, Rajagopalan Krishnan, Sini Nanadath Shibu, Dirk Poelman, Ankush Kumar Badyal, Arup K. Kunti, Hendrik C. Swart, Samvit G. Menon

Cappa Publications

This review provides a comprehensive discussion on the microwave-assisted synthesis of various materials for photoluminescence and photocatalytic applications. In the past decade, because of its ability to synthesize nanomaterials through faster, cleaner and more cost-effective routes compared to conventional heating, microwave techniques have gained significant importance for the synthesis of metal oxides, fluorides, sulphides, and quantum dots. Additionally, due to the uniqueness of its heating mechanism, the synthesis of materials in various nanostructured forms through microwave-assisted methods has been of great interest and is widely pursued. The materials thus synthesized have been applied as sensing elements in gas sensors, luminescent …

Initial Exploration Of Reduced Gyrations For Arkansas Asphalt Mix Designs, Jocie L. Baker

Graduate Theses and Dissertations

The most common distresses in asphalt pavement are cracking and rutting. These distresses plague almost every asphalt roadway in the world. Finding ways to mitigate these distresses will improve the performance of asphalt pavements. One way to combat the premature cracking of asphalt in the field is to ensure there is enough asphalt binder within the mix. This will help the flexibility of the asphalt undergoing large loads and deformation. However, it is widely accepted that mix designs across the country lack the appropriate amount of asphalt binder in their mixes, causing dry mix designs that are subject to cracking …

Study Of Electron Energy Filtering For Cold Electron Transport At Room Temperature, Pushkar Kiran Gothe

Material Science and Engineering Dissertations - Archive

The Fermi-Dirac thermal excitation of electrons at room temperature has been a significant limitation to many technologically important phenomena such as single electron transport. The electron thermal excitation also degrades the performance of modern electronic devices as well as spintronic devices. The scaling of metal-oxide-semiconductor field-effect transistors (MOSFETs) is hindered due to the thermal excitation of electrons at room temperature. Suppression of the thermally excited electrons at room temperature would therefore enable further scaling of the transistors, and in turn, improve the performance of electronic devices. This study demonstrates the suppression of electron thermal excitation at room temperature without using …

Hierarchical Microstructures To Overcome The Conflict Between Strength And Toughness Of Hard Coatings: Tin/Ni As A Model System, Ignacio Lopez Cabanas

Material Science and Engineering Dissertations - Archive

In the recent times, industry's production speed has been increasing and thus, the production of parts needs to adapt and so do the materials used to manufacture them. Hence, tools exposed to more extreme conditions using hard coatings need them to be more reliable. In this work an improvement of the toughness of TiN/Ni coatings is achieved through the combination of different microstructures at different levels. This first part consisted on finding the optimum TiN/Ni composition by using a high throughput methodology for a faster analysis and the second on the combination of that composition with a multilayer structure to …

Modeling Hierarchical Porous Electrodes With Tailored Anisotropic Structure, Debanjan Sarker

All Theses

Modern electric vehicles and consumer electronics applications demand high specific energy from Li-ion batteries, which can be charged and discharged faster. In the search for high specific energy, researchers have tried to make thicker battery electrodes which contain a greater proportion of active material. While chemical and structural modification of electrodes can help to increase the electronic conductivity of active material, the microstructure of porous electrodes can be engineered to enhance ion transport for fast charge and discharge. Previous research has shown that macropores introduced by directional freeze tape casting can enhance the performance of thick porous electrodes. For instance, …

Superhard Single-Phase (Ti,Cr)B2 Ceramics, Lun Feng, William Fahrenholtz, Gregory E. Hilmas, Laura Silvestroni

Materials Science and Engineering Faculty Research & Creative Works

A nominally pure and dense (Ti0.9Cr0.1)B2 ceramic was produced by spark plasma sintering of powders synthesized by boro/carbothermal reduction of oxides. The synthesized powders were a single phase and had an average particle of 0.4 ± 0.1 μm and an oxygen content of 1.2 wt%. Average Vickers hardness values of the resulting ceramics increased from 25.9 ± 0.8 GPa at a load of 9.81 N, to 46.3 ± 0.8 GPa at a load of 0.49 N. Compared to the nominally pure TiB2 ceramic obtained under the same processing conditions, the (Ti0.9Cr0.1)B2 ceramic had higher values under the same load due …

Shape Memory Alloys Via Halide-Activated Pack Equilibration, Andrew S. King, Ryan D. Dempsey, David W. Lipke

Materials Science and Engineering Faculty Research & Creative Works

Fabrication of shape memory alloy (SMA) components based on NiTi is challenging due to the precision with which elemental composition and microstructure must be controlled during processing to achieve desired shape memory behavior. Herein, a method to control chemistry in an NiTi SMA via halide-activated pack equilibration (SHAPE) against a constant chemical potential reservoir is described. To demonstrate the efficacy of the SHAPE process, an initially titanium-deficient specimen (pure nickel foam) has been equilibrated against an excess of an intimately mixed two-phase pack (NiTi + Ti2Ni) in the presence of a vapor phase transport agent (iodine). The two-phase pack regulates …

Elevated Temperature Thermal Properties Of Zrb2-B4c Ceramics, Eric W. Neuman, Matthew Thompson, William Fahrenholtz, Gregory E. Hilmas

Materials Science and Engineering Faculty Research & Creative Works

The elevated temperature thermal properties of zirconium diboride ceramics containing boron carbide additions of up to 15 vol% were investigated using a combined experimental and modeling approach. The addition of B4C led to a decrease in the ZrB2 grain size from 22 µm for nominally pure ZrB2 to 5.4 µm for ZrB2 containing 15 vol% B4C. The measured room temperature thermal conductivity decreased from 93 W/m·K for nominally pure ZrB2 to 80 W/m·K for ZrB2 containing 15 vol% B4C. The thermal conductivity also decreased as temperature increased. For nominally pure ZrB2, the thermal conductivity was 67 W/m·K at 2000 °C …

Fabrication And Non-Covalent Functionalization And Characterization Of Graphene-Based Devices On Novel Substrate Cadmium Trithiophosphate (Iv) — Cdps, Abayomi Omotola Omolewu

Graduate Theses and Dissertations

With graphene at the center of several application areas such as sensing, circuits, high-frequency devices for communication systems, etc., it is crucial to understand how the intrinsic properties of devices made from graphene and other materials like platinum and palladium nanoparticles affect the performance of such devices for the specific application area. Many graphene-based devices for different application areas have focused mainly on the material composition of the graphene-based devices and how it affects performance parameters for the specific application. However, it would be insightful to understand how the intrinsic electrical properties of the graphene devices for different applications affect …

Sub-Bandgap Photon-Assisted Electron Trapping And Detrapping In Algan/Gan Heterostructure Field-Effect Transistors, Andrew Gunn

All Theses

We have investigated photon-assisted trapping and detrapping of electrons injected from the gate under negative bias in a heterostructure field-effect transistor (HFET). The electron injection rate from the gate was found to be dramatically affected by sub-bandgap laser illumination. The trapped electrons reduced the two-dimensional electron gas (2DEG) density at the AlGaN/GaN heterointerface but could also be emitted from their trap states by sub-bandgap photons, leading to a recovery of 2DEG density. The trapping and detrapping dynamics were found to be strongly dependent on the wavelength and focal position of the laser, as well as the gate bias stress time …

Hierarchically Structured Photoelectrodes Via Atomic Layer Deposition, Justin Rowan Reed Demoulpied

Graduate Theses and Dissertations

In the search for a sustainable method to meet increasing energy needs, solar energy emerges as an underutilized, plentiful resource. Solar intermittency and requirements for transportation necessitate storing solar energy in the form of chemical bonds via artificial photosynthesis. Photoelectrochemical (PEC) water splitting generates hydrogen fuel from solar energy and water. A semiconducting material that successfully meets the complex requirements for building an industrially scalable PEC device has yet to emerge. This is leading to a reevaluation of materials previously overlooked within PEC research, mainly materials with limitations such as minimal charge carrier mobility and propensity to corrosion under illumination …

Controlled Manipulation Of Droplets On Fibers: Fundamentals And Printing Applications, Yueming Sun

All Dissertations

In this dissertation, the drop interactions with a single fiber is discussed under an application angle for the development on new Drop-on-Demand (DOD) printhead using a fiber-in-a-tube platform[1] to print highly viscous materials[2]. To control the drop formation and manipulation on fiber, one needs to know how the fiber wetting properties and the fiber diameter influence drop formation. And then, one needs to know the effects of fiber movement in the device on drop formation. These two questions constitute the main theme of this dissertation.

Before this study, it was accepted that the liquids could not form axisymmetric droplets if …

Quantifying The Workability Of Calcium Sulfoaluminate Cement Paste Using Time-Dependent Rheology, Sukanta K. Mondal, Adam Welz, Carrie Clinton, Kamal Khayat, Aditya Kumar, Monday Uchenna Okoronkwo

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Poor workability is a common feature of calcium sulfoaluminate (CSA) cement paste. Multiple chemical admixtures, such as set retarders and dispersants, are frequently employed to improve the workability and delay the setting of CSA cement paste. A quantitative assessment of the compatibility, efficiency, and the effects of the admixtures on cement paste workability is critical for the design of an appropriate paste formulation and admixture proportioning. Very limited studies are available on the quantitative rheology-based method for evaluating the workability of calcium sulfoaluminate cement pastes. This study presents a novel and robust time-dependent rheological method for quantifying the workability of …

Characterization Of Thermal Gelation Properties In Bioresorbable Thermally Activated Hydrogel Polymers For Hernia Surgery Applications, Alexander Mayfield

All Theses

Hydrogel adhesives are a new class of materials with excellent biocompatibility, which makes them very attractive for biomaterial applications. It has been previously shown that Tetronic T1107, a four-arm poly (propylene oxide)-poly (ethylene oxide) (PPO-PEO) block copolymer, is useful as a chemical crosslinking thermo-responsive hydrogel for bioadhesive applications. The end groups of this polymer are modified with acrylate and N-hydroxysuccinimide (NHS) functional groups. The acrylate end group gives the polymer cohesive properties with long-range chemical crosslinking using dithiothreitol (DTT), while the NHS end group gives the polymer adhesive properties through bonding with amines found in organic tissue. It was found …

3d Printed Multicomponent Polymer Based Materials Via Hybrid Filaments: Fabrication And Characterization, Erik Antonio

All Dissertations

Additive manufacturing, also known as 3D printing, promises a manufacturing revolution for both industry and academic circles. One of the most widely used method of 3D printing is Fused Deposition Modeling (FDM) or Fused Filament Fabrication (FFF), which requires a thermoplastic filament to be directed towards a heating block and then deposited via extrusion layer by layer to produce a finished part. However, there are significant issues with this technology, mainly a limitation on the materials available for use and mechanical property deficiencies when compared to traditional manufacturing. These issues are brought about by the temperature limited nature of the …

Xps And Ipe Determination Of Band Offsets Of Germanium Based Materials, Justin Michael Rudie

Graduate Theses and Dissertations

Germanium tin and silicon germanium tin are group IV semiconductor alloys that have gained significant interest in recent years for their potential use in optoelectrical devices. While silicon and germanium are indirect bandgap materials on their own, alloying them with tin in sufficient quantities leads to a transition to direct bandgap alloys. Direct gap performance opens the door for efficient light emitting and detecting devices fabricated entirely on group IV materials that are compatible with the industry standard CMOS manufacturing techniques. Germanium tin and silicon germanium tin have bandgaps that respond to light in the mid to near infrared spectrum …

Etching Process Development For Sic Cmos, Weston Reed Renfrow

Graduate Theses and Dissertations

Silicon Carbide (SiC) is an exciting material that is growing in popularity for having qualities that make it a helpful semiconductor in extreme environments where silicon devices fail. The development of a SiC CMOS is in its infancy. There are many improvements that need to be made to develop this technology further. Photolithography is the most significant bottleneck in the etching process; it was studied and improved upon. Etching SiC can be a challenge with its reinforced crystal structure. Chlorine-based inductively coupled plasma (ICP) etching of intrinsic SiC and doped SiC, SiO2, and Silicon has been studied. A baseline chlorine …

Study Of Single-Photon Wave-Packets With Atomically Thin Nonlinear Mirrors, Christopher Klenke

Graduate Theses and Dissertations

A novel controlled phase gate for photonic quantum computing is proposed by exploiting the powerful nonlinear optical responses of atomically thin transition metal dichalcogenides (TMDs) and it is shown that such a gate could elicit a π-rad phase shift in the outgoing electric field only in the case of two incident photons and no other cases. Firstly, the motivation for such a gate is developed and then the implementation of monolayer TMDs is presented as a solution to previous realization challenges. The single-mode case of incident photons upon a TMD is derived and is then used to constrain the more …

Understanding Charge Effects On Marked Ball Wear Rates – A Corrosion Study, John Bailey Fletcher

Masters Theses

"To measure the wear rates of grinding balls within a ball mill, marked ball wear tests (MBWTs) have been used extensively. Using the wear rates from a MBWT, operators select the most cost-effective media for their grinding application. One factor that a MBWT does not account for is the possible interaction between different media materials which could affect their corrosion rates. Galvanic coupling between dissimilar metals can cause significant changes in their corrosion rates. While galvanic interactions between minerals and grinding media have been studied, the interaction between dissimilar media has not. Corrosion rates and potentials of modern high carbon …

Effect Of Boron In Cast Iron, Suyash Durendra Pawaskar

Masters Theses

"Boron, mostly considered a residual element, has started to cause issues in the cast iron foundries by causing a decrease in the strength of pearlitic gray and ductile iron castings. Because of the increase in the use of boron-added steel scrap from automotive steel and a lack of agreement on the critical levels of boron in cast iron, foundries are facing difficulties in controlling the microstructure of gray iron castings when boron is present. The current investigation was designed to analyze the effects of boron in cast irons and predict a mechanism to understand its effects with a vision of …

Fabrication Of Nb3Sn By Magnetron Sputtering For Superconducting Radiofrequency Application, Md Nizam Sayeed

Electrical & Computer Engineering Theses & Dissertations

Particle accelerators are considered as an important device that has wide applications in cancer treatment, sterilizing waste, preserving foods, ion implantation in semiconductor industry, and in production of isotopes for medical applications. Superconducting radiofrequency (SRF) cavities are the building blocks of a linear particle accelerator. Current particle accelerators use niobium (Nb) superconductors as the sheet material to fabricate a single SRF cavity for particle acceleration. With better superconducting properties (critical temperature T_c ~ 18.3 K, superheating field H_sh~ 400 mT), Nb₃Sn is considered a potential candidate in SRF technology. Magnetron sputtering is a promising deposition …