Materials Science and Engineering Commons^™

Thermodynamic Prediction And Experimental Verification Of Multiphase Composition Of Scale Formed On Reheated Alloy Steels, Richard Osei, Semen Naumovich Lekakh, Ronald O'Malley

Materials Science and Engineering Faculty Research & Creative Works

The structure, phase, and composition of scale formed on a continuously cast steel slab during reheating depend on intrinsic factors (steel chemistry, microstructure, and as-cast surface condition) and extrinsic parameters (temperature, time, composition, and velocity of combustion gas atmosphere). The scale that forms on a slab normally has several layers with differing compositions and phases and knowledge of this scale structure is important in subsequent descaling and hot rolling processing steps. Formation of multiphase scale structures on steel during high temperature oxidation in reheat furnace proceeds according to a local thermodynamic equilibrium, while thickness of layers depends on kinetic conditions …

Photoinduced Trapping Of Charge At Sulfur Vacancies And Copper Ions In Photorefractive Sn2P2S6 Crystals, Timothy D. Gustafson, Eric M. Golden, Elizabeth M. Scherrer, Nancy C. Giles, A. A. Grabar, Sergey A. Basun, Jonathan E. Slagle [*], Larry E. Halliburton

Faculty Publications

Electron paramagnetic resonance (EPR) is used to monitor photoinduced changes in the charge states of sulfur vacancies and Cu ions in tin hypothiodiphosphate. A Sn₂P₂S₆ crystal containing Cu+ (3d10) ions at Sn²⁺ sites was grown by the chemical vapor transport method. Doubly ionized sulfur vacancies (V²⁺S) are also present in the as-grown crystal (where they serve as charge compensators for the Cu+ ions). For temperatures below 70 K, exposure to 532 or 633 nm laser light produces stable Cu²⁺ (3d⁹) ions, as electrons move from Cu⁺ ions to …

The Hot Cracking Susceptibility Subjected The Laser Beam Oscillation Welding On 6xxx Aluminum Alloy With A Partial Penetration Joint, Minjung Kang, Jason Cheon, Dong Hyuck Kam, Cheolhee Kim

Mechanical and Materials Engineering Faculty Publications and Presentations

A laser beam oscillation method using Galvano mirrors, which allows wide weld beads and controls thermal stress distribution, was suggested to suppress the formation of solidification cracks in laser welds. In order to understand the solidification cracking behavior in relation to the bead shape, laser beam oscillation welding was performed under various oscillation widths and frequency conditions. To evaluate the effect of the oscillation parameter on solidification cracking susceptibility, a regression analysis based on the shape of the bead was performed. Stress distribution generated during the laser beam oscillation welding process was also analyzed using finite element modeling simulation. From …

Economics Of Grid-Tied Solar Photovoltaic Systems Coupled To Heat Pumps: The Case Of Northern Climates Of The U.S. And Canada, Joshua M. Pearce, Nelson Sommerfeldt

Michigan Tech Publications, Part 1

Solar photovoltaic (PV) technology is now a profitable method to decarbonize the grid, but if catastrophic climate change is to be avoided, emissions from transportation and heating must also decarbonize. One approach to renewable heating is leveraging improvements in PV with heat pumps (HPs). To determine the potential for PV+HP systems in northern areas of North America, this study performs numerical simulations and economic analysis using the same loads and climate, but with local electricity and natural gas rates for Sault Ste. Marie, in both Canada and U.S. Ground-mounted, fixed-tilt, grid-tied PV systems are sized to match 100% of electric …

Nanoengineered Materials For Energy Conversion & Storage Applications: A Density Functional Theory Study, Ahmed Biby

Theses and Dissertations

The conventional approach for the development of novel materials has become long relative to the desired product development cycle. Thus, the sluggish pace of the development of materials within the conventional approach hinders the rapid transformation of the scientific outcomes into useful technological products. To this end, the field of hierarchical materials informatics evolved to bridge this gap. In this field, the multiscale material internal structure is considered the starting point and the core of this approach. This being said, the density functional theory (DFT) was used to generate useful materials data for the advancement of the hierarchical materials data-bases …

Assessment Of Heavy Metal Concentration In Soils Around Geita The Gold Mine, Tanzania, Mariam G. Mgendi, Mkabwa L. K Manoko, W.J.S. Mwegoha, C. Southway C. Southway

Journal of Humanities and Social Sciences

Health issues related to gold mining cannot be underestimated. Gold mining produce acid mine drainage (AMD), which in turn releases heavy metals into the nearby environment, hence causing environmental pollution. Heavy metals are naturally very toxic, thus pose a great health concern especially when their concentration exceeds the recommended permissible limits. In this study, concentrations of five heavy metals—including Pb, Ni, Cr, Cu and Zn—were assessed in the soil around Geita Gold Mine (GGM). A total of 17 sampling sites were established from which the soil samples were collected at 0-15cm and 15-30cm soil depth. The concentration of both total …

Synthesis And Characterization Of Perovskite-Based Materials For Memory Device Application, Gregory Thien Soon How

Student Works (2020-2029)

This project aims to study the resistive switching behaviour in memory devices using perovskites-based structures. A hybrid organic-inorganic lead halide perovskite was studied in this project, specifically methylammonium lead triiodide, CH3NH3PbI3 or MAPbI3 perovskite. The effect of the various counter electrodes in MAPbI3 perovskite was investigated by fabricating MAPbI3 perovskite on Indium Tin Oxide (ITO). Three commonly used electrodes which are Aluminium (Al), Silver (Ag), and Gold (Au) were thermally evaporated on top of the MAPbI3 perovskite layer. It was found that the ITO/MAPbI3/Al exhibits Resistive Random Access Memory (ReRAM) behaviour with SET voltage (VSET) of 4.5 V and RESET …

Nanoscale Enhancement Of Photosensitized Radionuclide Stimulated Therapy, Daniel Douglas Lane

McKelvey School of Engineering Graduate Student Theses & Dissertations

Photodynamic therapy (PDT) provides efficient tumor killing through the generation of reactive oxygen species (ROS) from the optical excitation of a photosensitizer (PS). Furthermore, this mechanism is highly immune stimulating, providing systemic tumor immunity with a reduction in metastasis. However, these materials had previously been limited by their dependence upon external light sources, allowing treatment of only laser-accessible malignancy. With the recent development of photosensitized radiation stimulated therapy (PRaST) this depth dependence is broken through co-localization of radionuclides and semiconducting photosensitizers. This dissertation focuses on the enhancement of titanium dioxide (TiO2) based PRaST agents through understanding of TiO2 material parameters …

Multifunctional Polydopamine Nanomaterials For Biomedical And Environmental Applications, Hamed Gholami Derami

McKelvey School of Engineering Graduate Student Theses & Dissertations

Polydopamine (PDA), a synthetic and organic material, has emerged as a promising materialplatform for various applications in energy, environmental, and biomedical fields. PDA, formed by self-polymerization of dopamine, is rich in catechol and amine groups, which facilitate covalent conjugation and/or other non-covalent interactions with organic and inorganic materials. It is highly biocompatible, biodegradable, has broadband light absorption spectrum and excellent light-to-heat conversion efficiency. Also, it is easy to synthesize and functionalize. The combination of excellent characteristics of polydopamine-based nanomaterials, make them a promising adsorbent agent for environmental wastewater treatment and photothermal agent for biomedical applications. In the first half of …

Mechanical Strength Of Germanium Doped Low Oxygen Concentration Czochralski Silicon And The Effect Of Oxygen On Nitrogen Dissociation In Silicon, Junnan Wu

McKelvey School of Engineering Graduate Student Theses & Dissertations

During the Czochralski growth of silicon, it is inevitable for oxygen to be incorporated into the silicon crystal from the quartz crucible. Interstitial oxygen improves the mechanical strength of silicon by pinning and locking dislocations, but also generates thermal donors during device processes, shifting the electrical resistivity. For silicon wafers used in radio frequency (RF) applications, it is important to ensure the high resistivity of the substrates for good RF characteristics. Therefore, the oxygen level in these high resistivity silicon wafers is kept very low (< 2.5 × 1017 atoms/cm3) by carefully controlling the Czochralski growth conditions, in order to reduce the thermal donor concentration to an acceptable level. Silicon on insulator (SOI) substrates made from high resistivity wafers have been widely used for RF applications. SOI manufacturing includes multiple high temperature thermal cycles (1000 – 1100 °C), during which the high resistivity wafers are prone to slip and warpage. Therefore, it is technologically important to recover some of the lost mechanical strength due to the lack of oxygen by introducing electrically inactive impurities to suppress the dislocation generation and mobility in silicon. Germanium (Ge) as an isovalent impurity is 4% larger in size and forms a solid solution with silicon in the entire concentration range. Previous works have shown Ge doping at high concentrations above 6 × 1019 atoms/cm3 increased mechanical strength of silicon with high oxygen concentration (~ 1 × 1018 atoms/cm3). In this work, we explore the effect of Ge doping (7 - 9 × 1019 atoms/cm3) on the mechanical strength of low oxygen concentration (< 2 × 1017 atoms/cm3) silicon, where the oxygen associated dislocation locking and pinning are very low. A mechanical bending test was used to study the average dislocation migration velocity and the critical shear stress of dislocations motion at 600 – 750 °C for Ge doped, nitrogen doped, and undoped low oxygen samples, as well as nitrogen doped float-zone and un-doped high oxygen concentration samples. Next, we fabricated SOI substrates using these high resistivity wafers and compared their slip generation rates and the slip-free epitaxial grow temperature windows after the high temperature thermal cycles (> 1000 °C). Our results indicate at lower temperature Ge doesn’t affect the dislocation mobility …

Flexible Nanopaper Composed Of Wood-Derived Nanofibrillated Cellulose And Graphene Building Blocks, Qing Li, Ming Dai, Xueren Qian, Tian Liu, Zhenbo Liu, Yu Liu, Ming Chen, Wang He, Suqing Zeng, Yu Meng, Chenchen Dai, Jing Shen, Yingtao Liu, Wenshuai Chen, Wenbo Liu, Ping Lu

College of Science & Mathematics Departmental Research

Nanopaper has attracted considerable interest in the fields of films and paper research. However, the challenge of integrating the many advantages of nanopaper still remains. Herein, we developed a facile strategy to fabricate multifunctional nanocomposite paper (NGCP) composed of wood-derived nanofibrillated cellulose (NFC) and graphene as building blocks. NFC suspension was consisted of long and entangled NFCs (10–30 nm in width) and their aggregates. Before NGCP formation, NFC was chemically modified with a silane coupling agent to ensure that it could interact strongly with graphene in NGCP. The resulting NGCP samples were flexible and could be bent repeatedly without any …

Research Trend Of Metal Matrix Composites Reinforced With Silica Extracted By Green Route: A Bibliometric Analysis, Rinku Datkhile, Meena Laad, Babaji Ghule

Library Philosophy and Practice (e-journal)

Metal Matrix Composites have acquired an important place in the engineering applications due to their distinctive characteristics such as high specific strength, lower specific gravity, improved material stiffness, better durability, enhanced creep and fatigue strength etc. Worldwide scientists are working on the improvement of mechanical properties of composite materials. The present work attempts to summarise all the research carried out on metal matrix composites reinforced with silica extracted by green route and provides up-to-date research material for researchers who are interested in the field of composites with metal matrices. Scopus databases and software such as Gephi Vos Viewer and Table2Net …

Gas Measurement Device, Megan C. Frost, Weilue He

Michigan Tech Patents

A device including a first chamber, a second chamber, and a membrane permeable to neutral gases but impermeable to water that is positioned between the first chamber and the second chamber. The membrane includes a first layer including PVDF and PDMS, and the PVDF has a plurality of pores at least partially filled with at least some of the PDMS.

Corrosion Protective Film Formation On Mg Alloys Az 31 By Exposure To Dilute Selenite Solutions, Zhiyuan Feng, Charles C. Xu, Dadi Zhang, Rudolph Buchheit

Chemical and Materials Engineering Faculty Publications

The study of protective film formation on Mg alloys by exposure to sodium selenite solutions was conducted. Anodic polarization studies, electrochemical impedance spectroscopy studies, morphological analysis, and Energy-dispersive X-ray spectroscopy were performed on AZ31 Mg alloy after coating treatment in different concentrations of sodium selenite. The corrosion resistance was improved by around 5 times compared with control. Improved resistance to localized corrosion was observed in the coatings treated by 5 mM or 10 mM sodium selenite. The protection mechanism was ascribed to the transformation of selenite to insoluble selenium, the formation of insoluble MgSeO₃ hydrate, and polymerization of amorphous …

Upshot Of Heterogeneous Catalysis In A Nanofluid Flow Over A Rotating Disk With Slip Effects And Entropy Optimization Analysis, Muhammad Ramzan, Saima Riasat, Jae Dong Chung, Yu-Ming Chu, M. Sheikholeslami, Seifedine Kadry, Fares Howari

All Works

The present study examines homogeneous (HOM)–heterogeneous (HET) reaction in magnetohydrodynamic flow through a porous media on the surface of a rotating disk. Preceding investigations mainly concentrated on the catalysis for the rotating disk; we modeled the impact of HET catalysis in a permeable media over a rotating disk with slip condition at the boundary. The HOM reaction is followed by isothermal cubic autocatalysis, however, the HET reactions occur on the surface governed by first-order kinetics. Additionally, entropy minimization analysis is also conducted for the envisioned mathematical model. The similarity transformations are employed to convert the envisaged model into a non-dimensional …

Development Of Graphene Synthesis And Characterization Techniques Toward Cmos Applications And Beyond, Otto Kno Zietz

Dissertations and Theses

Graphene exhibits mechanical and electrical properties which, coupled with its two dimensional (2D) morphology, make it an attractive material component for inclusion in a wide range of industries. Since the discovery of graphene in 2004, industry adoption has been limited due to the demanding synthesis requirements for high quality and connected graphene as well as the difficulties associated with direct incorporation. Chemical vapor deposition (CVD) has emerged as the most cost efficient method for producing high quality graphene at scales suitable for mass production. However, the 1000°C temperatures and micrometer thick catalysts required for this process preclude direct inclusion in …

N-Type Charge Transport In Heavily P-Doped Polymers, Zhiming Liang, Hyun Ho Choi, Xuyi Luo, Tuo Liu, Ashkan Abtahi, Uma Shantini Ramasamy, J. Andrew Hitron, Kyle N. Baustert, Jacob L. Hempel, Alex M. Boehm, Armin Ansary, Douglas R. Strachan, Jianguo Mei, Chad Risko, Vitaly Podzorov, Kenneth R. Graham

Chemistry Faculty Publications

It is commonly assumed that charge-carrier transport in doped π-conjugated polymers is dominated by one type of charge carrier, either holes or electrons, as determined by the chemistry of the dopant. Here, through Seebeck coefficient and Hall effect measurements, we show that mobile electrons contribute substantially to charge-carrier transport in π-conjugated polymers that are heavily p-doped with strong electron acceptors. Specifically, the Seebeck coefficient of several p-doped polymers changes sign from positive to negative as the concentration of the oxidizing agents FeCl3 or NOBF4 increase, and Hall effect measurements for the same p-doped polymers reveal that …

Wetting And Brazing Of Yig Ceramics Using Ag–Cuo–Tio2 Metal Filler, Wanqi Zhao, Shuye Zhang, Jian Yang, Tiesong Lin, Dusan P. Sekulic, Peng He

Mechanical Engineering Faculty Publications

The wetting and brazing of Y₃Fe₅O₁₂ (YIG) ceramics with a Ag–8CuO–2TiO₂ filler was investigated for the first time. For comparison, the wettability of a Ag–10CuO filler on YIG ceramics was similarly investigated. The Ag–8CuO–2TiO₂ filler has an equilibrium contact angle of approximately 31 °C on the YIG substrate at 1000 °C; thus, its wettability is excellent. Moreover, its wettability exceeds that of Ag–10CuO. The microstructure and the interfacial structure between the filler and the substrate were determined using scanning electron microscopy, X-ray diffraction, EPMA and transmission electron microscopy. The liquid Ag–8CuO–2TiO₂ filler …

Quantifying Charge Transport In Chemically Doped Semiconducting Polymers, Shawn Gregory

Link Foundation Energy Fellowship Reports

This report is for the Link Foundation, which generously provided me a graduate research fellowship. In this report, I outline a segment of the organic electronics and organic thermoelectrics fields, then detail the contributions I have made, and finally conclude with a perspective on these fields. Subsequently, in accordance with the fellowship reporting requirements, I list all articles that I have published or will publish whose funding originated (in part) from the Link Foundation. Lastly, I share some personal notes on how this fellowship impacted my PhD experience and career.

Jcati Base Plate, Jacob Atamian

All Undergraduate Projects

Students of the Mechanical Engineering Technology (MET) program at Central Washington University have contributed to an ongoing Carbon Fiber Recycler project funded by the Joint Center for Aerospace Technology Innovation (JCATI). The goal of this project was to modify the existing recycling system to produce a higher success rate of recycled carbon composite material. This report focuses on increasing the rigidity of the crushing gears so that the deflection occurring among the components during operation was below 0.005 inches to ensure proper operating conditions. The operating speed of the crushing gears was 2.5 rpm with a crushing load of 10,500 …

Jcati Carbon Fiber Recycling Shredder, Benjamin Cooley

All Undergraduate Projects

Once carbon fibers are cast into a resin and used in a composite material, retrieving those fibers can be a difficult task. However, it is beneficial to recycle and reuse the fibers from old unneeded components rather than pay the cost of acquiring new ones. The Joint Center for Aerospace Technology Innovation (JCATI) carbon fiber recycling device condenses the multistep process of extracting the fibers by integrating all steps into one automated device. In the previous version of the device, the cutting blades turned the long composite strips into thin fingers but did not sever them across the width.

The …

Surface Acoustic Waves Increase Magnetic Domain Wall Velocity, Anil Adhikari, Shireen Adenwalla

Shireen Adenwalla Papers

Domain walls in magnetic thin films are being explored for memory applications and the speed at which they move has acquired increasing importance. Magnetic fields and currents have been shown to drive domain walls with speeds exceeding 500 m/s. We investigate another approach to increase domain wall velocities, using high frequency surface acoustic waves to create standing strain waves in a 3 micron wide strip of magnetic film with perpendicular anisotropy. Our measurements, at a resonant frequency of 248.8 MHz, indicate that domain wall velocities increase substantially, even at relatively low applied voltages. Our findings suggest that the strain wave …

Aps March Meeting 2021 (Online) Updates On Scientific Research During Pandemic Times, Vianney Gimenez-Pinto

Title III Professional Development Reports

While the ongoing global pandemic continues to affect our everyday lives, researchers in Science, Technology, Engineering and Math found a way to come together at the American Physical Society (APS) March Meeting 2021. The conference was online-only and had more than 11,000 registered attendants who actively participated in the program during March 14- 19, 2021.

Jcati Pyrolysis System, Jack Dutton

All Undergraduate Projects

The Joint Center for Aerospace Technology Innovation (JCATI) project is designed to recycle carbon fiber pieces for use in manufacturing. Part of the system requires the removal of resin from the carbon fibers to facilitate the recycling of carbon fiber. To accomplish this task the pyrolysis process is implemented using a commercial grade oven with a conveyor system. Argon gas is injected into the shroud and over the oven to purge the interior of oxygen. The conveyor system enables this to be a batch process. A ramp is used to allow simple addition of material to the conveyor system and …

Balsa Wood Bridge, Andrew Harris

All Undergraduate Projects

Faculty at Central Washington University proposed a challenge to mechanical engineering students that could be accomplished in an in-home setting. The goal was to create a balsa wood bridge, weighing no more than 85 grams, that can support a load over an open span and raise above its resting position by means of a mechanical system. To produce a successful solution to the problem, a vertical lift bridge was created consisting of two lifting towers and a load bearing bridge. Using equations of static equilibrium and strength of materials, the required width for each member was determined. Project requirements were …

Observation Of New Particle Formation In The Northern Hemisphere At Altitude From 4 To 20 Km, Mohamed Saad

Electronic Theses and Dissertations

New particle formation (NPF) is investigated using measurements of aerosol size distributions and meteorological variables made in two continents, including USA and Europe. Despite the considerably different aerosol particle abundances among the sites, a common relationship was found between the characteristics of NPF events and the air mass convective and/or advective transport. CO and O3 act as tracers of tropospheric and stratospheric air, respectively, their statistical relationship can be used to quantify air mass characteristics and origins. The mixing ratio values of CO increased within the upper troposphere layer before/during NPF events, which may serve as an indicator of occurring …

Mini Rc Baja Car, Jason Schindler

All Undergraduate Projects

Incorporating each aspect of engineering incorporated into a senior project is difficult. That is why an RC Baja car is a great senior project for Mechanical Engineering students. The approach that students must take to design, construct, and test the car is to set parameters, and to make overall goals that can be easily measured. These goals include, but not limited to things like a $700 budget and the ability to withstand a 1-foot drop to a flat surface on all four wheels simultaneously. First, the design must meet the specifications and rules that are set previously. This ensures that …

Big Data Analysis Of Nanoscience Bibliometrics, Patent, And Funding Data (2000-2019), Yuliang Zhao, Zhixiang Wei, Qing Dai, Hongwei Dong, Hongjun Xiao, Shuxian Wu, Xingxing He, Beverley Mitchell, Thomas A. Collins, Sarah Huggett, John Van Orden, Christiane Barranguet, Basak Candemir

Public Reports

Given the strategic significance of Nanoscience and nanotechnology, it is essential to evaluate and predict its developmental trends. This report is based on the largest abstract and citation database of peer-reviewed literature, Elsevier's Scopus, along with the research evaluation platform SciVal. The funding and patent analysis data for the report is from Funding Institutional and PatentSight, respectively. This report provides an evaluation of Nanoscience's scientific output, role, contribution, and impact through bibliometric analysis, combined with big data indicators of Nanoscience scientific results and patents from 2000 to 2019.

Recycling Of Fiber Polymer Matrix Composites In Cementitious Materials, Edward Patton Clark

Electronic Theses and Dissertations

Recycling options for fiber polymer matrix composite waste materials are limited because they typically cannot be reused, reprocessed for down-cycling, and are generally environmentally unfriendly. The utility industry, specifically electrical distribution, has been increasingly using hybrid carbon, glass fiber, and epoxy resin composite rods for high-voltage (HV) conductor transmission lines. The high-voltage conductor core (HVCC) used in the transmission line can have an optimal in-service-life of roughly several decades, in which the material is then retired to a waste landfill. Currently, there is limited research and recycling methodology for these hybrid composite rods. In this research, powder carbon fiber, glass …

Effects Of Resin Chemistries On The Selective Removal Of Industrially Relevant Metal Ions Using Wafer-Enhanced Electrodeionization, Humeyra B. Ulusoy Erol, Christa N. Hestekin, Jamie A. Hestekin

Chemical Engineering Faculty Publications and Presentations

Wafer-enhanced electrodeionization (WE-EDI) is an electrically driven separations technology that occurs under the influence of an applied electric field and heavily depends on ion exchange resin chemistry. Unlike filtration processes, WE-EDI can be used to selectively remove ions even from high concentration systems. Because every excess ion transported increases the operating costs, the selective separation offered by WE-EDI can provide a more energy-efficient and cost-effective process, especially for highly concentrated salt solutions. This work reports the performance comparison of four commonly used cation exchange resins (Amberlite IR120 Na⁺, Amberlite IRP 69, Dowex MAC 3 H⁺, and …