Materials Science and Engineering Commons^™

Dissimilar Metal Weld Variability Due To Lot Differences In Nitinol/ Stainless Steel Interface, Matthew R. Rudow

Materials Engineering

Abstract

An experiment was conducted to determine and reduce the causes of variation between a 304 Stainless Steel and super elastic Nickel Titanium dissimilar metal weld. Six factors were established to understand the cause of variation: perpendicularity, final grind, surface finish, weld force, weld pulse duration, and alignment. Using a rotational test with an air piston break pressures were established and charted in Minitab to identify trends. It was shown that weld force and weld pulse duration were the two factors that had the most influence on break strength. This data also showed that higher strength groups had less variability. …

Flexi-Focus Lens: Pdms Variable Focal Length Lens, Patrick Angulo, Alex Doyle, Dylan Mcdaniel, Michael Olivarez

Industrial and Manufacturing Engineering

The design of a variable focal length, or flexi-focus, polydimethylsiloxane (PDMS) lens incorporating a light emitting diode (LED) source is intended for future use on board commercial aircraft. Specifically, the design is intended for the Boeing 787 Dreamliner aircraft, serving as a personal reading light for the passengers seated in the cabin. Most current reading lights on board aircraft are rigid, incandescent, and have very limited freedom in terms of adjusting the emitted light. Incandescent lamps are also inefficient with respect to energy consumption and light output as well as a high heat output. In an economy of increasing demand …

A Rheological Model Of The Dynamic Behaviour Of Magnetorheological Elastomers, Lin Chen, Stephen Jerrams

Articles

A rheological model is described that was developed to simulate the dynamic behaviour of magnetorheological elastomers (MREs). The viscoelasticity of the polymer composite, magnetic field induced properties and interfacial slippage between the matrix and particles were modelled by analogy with a standard linear solid model, a stiffness variable spring and a spring-Coulomb friction slider respectively. The loading history and rate dependent constitutive relationships for MREs were derived from the rheological model. The hysteresis loop from shear strain - shear stress plots, which determines the shear modulus and loss factor, were obtained from substituting cyclic loading into these constitutive relationships. The …

Determining A Method For Rendering Low Cost Cdse(Zns) Core(Shell) Quantum Dots Aqueous Soluble Via Amphiphilic Polymer Wrapping, Patrick Mcbride

Materials Engineering

Herein is described the procedure of two amphiphilic polymer wrapping techniques that may be employed for obtaining aqueous soluble quantum dots (QDs) for use in biological fluorescent imaging applications. The advent of QDs has led to new nanoscale fluorescent materials that exhibit unparalleled quantum yields (QYs), high resistance to photobleaching, tunable emissions, and
absorption over a large optical range. However, the QD synthesis employed here at Cal Poly to obtain bright, photostable CdSe(ZnS) core(shell) QDs involves the use of organic solvents and surfactants, leading to hydrophobic QDs. Since all of biology relies on aqueous solubility, this hydrophobicity creates a major …

Artificial Muscle Project: Process Development Of Polydimethyl Siloxane Thin Films For Use In Dielectric Electroactive Polymer Artificial Muscle Actuators, Vincent J. Gayotin, Richard W. Morrison, Paul A. Preisser

Materials Engineering

An artificial muscle design was created founded on the principles of a dielectric electroactive polymer (DEAP), which is fundamentally similar to a capacitor. A polydimethyl siloxane (PDMS)-based elastomer, Sylgard 184 from Dow Corning, was chosen for the design and spun coat onto polystyrene (PS) Petri dishes at varying speeds to create a thin film, using speeds of 2000 rpm, 3000 rpm, 4000 rpm, 5000 rpm, and 6000 rpm. The film thicknesses were measured optically through use of a microscope with coupled computer imaging software to generate a characteristic curve of film thickness to spin speed, achieving a minimum film thickness …

Design And Characterization Of A Process For Bulk Synthesis Of Cadmium Selenide Quantum Dots, Susan Harada

Materials Engineering

The objective of the process is to synthesize quantum dots that will fluoresce over the visible spectrum of 450 to 650nm; then to mix the quantum dots together in a polymer matrix so that when illuminated with a blue LED the mixture yields “white” light. The current quantum dot synthesis is a chemical process that involves adding a room temperature Se-TOP precursor to a 225°C Cd precursor solution to cause nucleation and growth of nanoparticles. This method, however, only yields quantum dots that fluoresce in the 520 to 600nm range. In order to create the “white” light phosphor replacement, red …

Materials Characterization Of Bamboo And Analysis Of Bonding Strength And Internal Strength As A Structural Member In Reinforced Concrete, Nithi Plangsriskul, Nicholas Dorsano

Materials Engineering

This study evaluates the potential to utilize bamboo as reinforcement in concrete structural members.  In this project, the mechanical properties of bamboo were tested, specifically force required to embed a 0.5” diameter ball 0.016” into the bamboo samples and its bonding strength with concrete.  One type of bamboo, Bambusa Oldhamii, was cut into eight sections, approximately 2.54 cm wide, along the length of the culm.  The compression test recorded the bamboo’s strength at eight points along the length of the internode and at three points along the transverse direction of each specimen.  Bambusa Oldhamii’s specimen base 1 data for inner, …

Understanding The Effects Of Temperature Extremes On The Tensile And Short Beam Shear Strength Of Epoxy-Based, Glass-Fiber Reinforced Composites, Jonathan Blake Patterson

Materials Engineering

Aptera (Oceanside, CA) has developed two epoxy-based, silica fiber-reinforced composites to be used on their three-wheeled all-electric vehicle called the 2e.  Aptera’s composites were studied at temperature extremes using a dynamic mechanical analysis (DMA) system and by tensile and short beam shear (SBS) testing using an Instron testing system. These tests were conducted to simulate the loading of the composite in the 2e vehicle.  Tensile and short beam shear samples were machined to 150 mm x 25 mm x 2 mm and 40 mm x 13 mm x 6 mm, respectively.  DMA samples were machined to 30 mm x 5 …

The Design And Manufacture Of A Microfluidic Reactor For Synthesis Of Cadmium Selenide Quantum Dots Using Silicon And Glass Substrates, Peter Gonsalves

Materials Engineering

A microfluidic reactor for synthesizing cadmium selenide (CdSe) quantum dots (QDs) was synthesized out of silicon and Pyrex glass. Microfabrication techniques were used to etch the channels into the silicon wafer. Holes were wet-drilled into Pyrex glass using a diamond-tip drill bit. The Pyrex wafer was aligned to the etched silicon wafer and both were anodically bonded to complete the microfluidic reactor. Conditions for anodic bonding were created by exposing the stacked substrates to 300V at ~350^oC under 5.46N of force.  Bulk CdSe solution was mixed at room temperature and treated as a single injection. The syringe containing …

Large Kinetic Asymmetry In The Metal-Insulator Transition Nucleated At Localized And Extended Defects, W. Fan, Jinbo Cao, J. Seidel, Yijia Gu, J. W. Yim, For Full List Of Authors, See Publisher's Website.

Materials Science and Engineering Faculty Research & Creative Works

Superheating and supercooling effects are characteristic kinetic processes in first-order phase transitions, and asymmetry between them is widely observed. In materials where electronic and structural degrees of freedom are coupled, a wide, asymmetric hysteresis may occur in the transition between electronic phases. Structural defects are known to seed heterogeneous nucleation of the phase transition, hence reduce the degree of superheating and supercooling. Here we show that in the metal-insulator transition of single-crystal VO 2, a large kinetic asymmetry arises from the distinct spatial extension and distribution of two basic types of crystal defects: point defects and twin walls. Nanometer-thick twin …

Characterisation, Modelling And Simulation Of Flexible Polyurethane Foam, Conor Briody, Barry Duignan, Stephen Jerrams

Conference Papers

Flexible polyurethane foam is an open-celled polymeric material that exhibits strain rate and temperature effects. It has found various applications in areas including the packaging, medical, sports, aerospace and aeronautical industries. Polyurethane foam is ubiquitous in seating applications and finds particular use in specialised wheelchair seating where customised seating solutions are required which can provide proper comfort and support without the risk of developing pressure ulcers. Proper seating design is critical for users if this problem is to be avoided, but a lack of quantitative knowledge of this material’s behaviour has limited its effectiveness. The objectives of the work presented …

The Effects Of Heat Treatment On Area Percent Porosity And Corrosion Behavior Of High-Nickel Thermal Spray Coatings, Travis Crowe, Alec Guraydin

Materials Engineering

Samples of two Thermal Spray Coating (TSC) alloys on a low carbon steel substrate were obtained: alloy C276 and Nicko-Shield 200. Specimens of each alloy were subjected to heat treatments at temperatures at 1100° for 60 minutes and 1200° for 10 minutes, with some specimens left in the as-sprayed condition. Three replicates were prepared for each condition. Thin 1” strips were cut using a diamond wafering blade for porosity measurements and 2” x 1” specimens were cut for corrosion testing using a SiC abrasive saw. The porosity specimens were mounted in acrylic resin, polished, and examined using SEM. From these …

Characterization Of A Pdms Microfluidic Reactor For Synthesizing Quantum Dots, Brian Harley

Materials Engineering

A PDMS microfluidic reactor was made in Cal Poly’s class 1000 clean room for the purpose of synthesizing quantum dots.  The device master mold was made from a silicon substrate and SU-8 features 50μm tall.  The PDMS reactor was cast from that mold.  The flow rates of fluid through the channels, heating of the reactor and pressure in the reactor were measured in order to characterize the potential for synthesizing quantum dots.  Flow rates of 20 mL/hr through 4 mL/hr were tested to characterize the consistency of amount of time the fluid remains in the reactor at a constant flow …

Characterization Of The Oxidation Kinetics Of Fecral Ferritic Stainless Steels At 900°C For Catalytic Converter Applications, Stacy Stamm

Materials Engineering

This study characterized the oxidation kinetics of two types of ferritic stainless steel foils used as substrates for catalytic converters. Catalytic converters rely on an alumina layer on the surface of the foils, which allows the catalyst to attach to the substrate. Because the alumina layer is so important, this study characterized the weight gain, thickness, and composition of the alumina as it grew at 900°C for up to 400 hours. The two foils characterized were an MK foil, used for gasoline engines, and an EMS foil, used for diesel engines. The MK foil showed a percent weight gain of …

Ir Nonlinear Absorption Leading To Laser-Induced Damage In Ge & Gasb, Torrey J. Wagner, Matthew J. Bohn, Ronald A. Coutu Jr., L. P. Gonzales, J. M. Murray, K. L. Schepler, S. Guha

Faculty Publications

Using a simultaneous fitting technique to extract nonlinear absorption coefficients from data at two pulse widths, we measure two-photon and free-carrier absorption coefficients for Ge and GaSb at 2.05 and 2.5 μm for the first time. Results agreed well with published theory. Single-shot damage thresholds were also measured at 2.5 μm and agreed well with modeled thresholds using experimentally determined parameters including nonlinear absorption coefficients and temperature dependent linear absorption. The damage threshold for a single-layer Al₂O₃ anti-reflective coating on Ge was 55% or 35% lower than the uncoated threshold for ps or ns pulses, respectively. Wavelength-dependant …

Characterization Of The Relationship Between The Microstructure And Tensile Strength Of Annealed Ti-6al-4v, Aldo Corona

Materials Engineering

Tensile coupons of Ti-6Al-4V were heat treated at varying annealing temperatures from 1200°F (648°C) to 1450°F (787°C)  at 50°F  (23°C) increments for 1 hour. The samples were air cooled to room temperature or furnace cooled to 800°F (426°C) followed by air cooling to room temperature. Four tensile coupons were treated at each annealing temperature and cooling rate. Alpha case was observed to form on the surface of the samples post heat treatment with a maximum depth of 25 µm (.001 in). Samples were tensile tested for their ultimate tensile strength, yield strength, and percent elongation.  Samples across all annealing temperatures …

The Effects Of Colorant Oxides And Firing Rate On The Nucleation And Growth Of Zinc Silicate Crystals In Crystalline Glazes, Nicolas Coffey

Materials Engineering

This study looked at the effects of colorant oxides and firing rate on the nucleation and growth of crystals in zinc-based crystalline glazes. One weight percent of iron and copper oxide powders were mixed separately with a zinc-based crystalline glaze. The uncolored glaze along with both colored glazes were applied to test tiles and fired. Two different firing schedules were used with different ramp up firing rates of 165°C/hr (slow) and 205°C/hr (fast). X-ray diffraction (XRD) analysis found both zinc oxide and silica oxide in the raw glaze, which are the main components in the formation of zinc silicate. XRD …

Processing Pdms Gecko Tape Using Isopore Filters And Silicon Wafer Templates, Boris Luu

Materials Engineering

Gecko tape was processed through nanomolding involving two types of templates. One template was a Millapore Isopore polycarbonate membrane filter and the other template was an n-type silicon wafer processed to include four different pore diameters. These pore diameters were 20, 40, 80, and 160 microns. AutoCAD was used to design to a mask to be used later during photolithography. Two n-type wafers were sputtered with aluminum, underwent photolithography, and then etched using reactive ion etching. A template was placed into a Petri dish and Sylgard 184 polydimethylsiloxane (PDMS) was poured on the template. Once the PDMS cured,   the 1 …

Oxidation Kinetics Of Silver Thin Films For Antimicrobial Applications In The Health Care Industry, Sean D. Morham

Materials Engineering

To determine if varying city water qualities from around the United States can support a developing “oxidation corrosion of silver thin films” method of creating aqueous ionic silver solutions for the anti-microbial treatment of healthcare linens, a test was devised holding all variables constant with the exception of water quality parameters. This corrosion style test was done in order to assess a pass/fail criteria of 25 ppb ionic silver concentration in the aqueous solutions which resulted from the corrosion of silver thin film coated substrates. Above 25 ppb being a pass, below 25 ppb being a fail. While varying the …

Investigating The Mechanical Properties Of Compression Molded Carbon Fiber Reinforced Sheet Molding Compound, Bradley A. Jones

Materials Engineering

Callaway Golf receives a proprietary blend of prepreg material from Quantum Composites. Callaway processes the prepreg in-house and supplied 254mm x 254mm x 1.3mm panels of carbon fiber sheet molding compound (CFSMC) for characterizing. Tensile strength was analyzed by conducting tensile tests per ASTM D3039. Tensile coupons were cut to 254mm long by 25.4mm wide. Tabs were constructed from 1.6mm thick GFRP printed circuit board material. A commercial grade two part epoxy was used to bond the tabs to the CFSMC. Tensile results were inconclusive due to consistent fractures occurring outside the gauge lengths of the specimens.

Flexure strength was …

A Study Of Three Transition Metal Compounds And Their Applications, Zhen Qin

Dissertations

The La_5/8-yPr_yCa_3/8MnO₃ with colossal magnetoresistance (CMR) effect has a rich phase diagram and is well studied for its electronic phase separation phenomenon, where the ferromagnetic (FM) metal order co-exists and competes with the charge-ordered (CO) insulator phase. High Pr doping will favor the CO order, leading a sharp FM to CO dominated phase transition around Pr concentration of 0.3 and above. Hydrostatic pressure favors FM metallic order without damaging the sample and can be tuned continuously. In this study, pressurized-magnetic and resistivity measurements was done on a La_0.25Pr_0.375Ca_{0.375 …}

Research Progress In Orthosilicates As Cathode Materials For Li-Ion Batteries, Dong-Ping Lv, Lin Wang, Yong Yang

Journal of Electrochemistry

Rechargeable Li-ion batteries fulfilling high-energy density, high safety, environmental friendliness, and low cost are demanded urgently for energy storage systems. Besides the structure stability arising from the strong Si-O covalent bond, environmental benignancy and low cost from the characteristics of Fe, Mn, Si elementals, orthosilicates (Li₂MSiO₄) show promising prospect to meet the demand of high-energy density for its two available Li+ per formula unit. Motivated by these significant advantages, Li₂MSiO₄ have been intensively investigated in the past few years. In the present work, we gave a review on the progress of orthosilicate research …

Effect Of Pore Size On Pseudo-Capacitive Performance Of Nio In The Mixed Electrolyte Of Koh And Hexacyanoferrate, Wen Wu, Meng-Yan Hou, Dan-Dan Zhou, Yong-Yao Xia

Journal of Electrochemistry

In this paper, five kinds of NiO samples with different pore size distributions were synthesized .The electrochemical capacitance of the samples were characterized in 3 mol/L KOH solution with and without hexacyanoferrate addition. Electrochemical test results indicated the NiO sample with an optimum pore size of about 15 nm shows high Coulombic efficiency of the N₄(NiO) electrode as the redox reaction of hexacyanoferrate ions would be limited in the pore, thus prevent ion diffusion into the bulk electrolyte solution .

The Flip-Flop Behavior Of Acetonitrile At Au Electrode Surface Investigated By Sum Frequency Generation Vibrational Spectroscopy, Zhi Huang, Xin Tang, Gang-Hua Deng, En-Cai Zhou, Hong-Fei Wang, Yuan Guo

Journal of Electrochemistry

The electrochemical interface between liquid acetonitrile and polycrystal gold electrode is investigated by in situ infrared visible sum frequency generation spectroscopy (SFG-VS). The structure of acetonitrile adsorbed at polycrystal gold electrode surface is studied as a function of electrode potential. The SFG spectra of CH₃ group indicate acetonitrile orients in response to the electrode potential. The SFG signal of CH₃ group turns lower as the electrode potential changes from -700mV to 300mV, and vanishes around the 300mV(pzc), then becomes a negative signal above 500mV, which indicates that the orientation is predominately with the CH₃ group toward the …

Preparation And Performance Of Carbon-Coated Si/C Composites, Li-Li Du, Quan-Chao Zhuang, Tao Wei, Yong-Li Cui, Zhi Sun, Shi-Gang Sun

Journal of Electrochemistry

Si/C composite for lithium ion batteries was obtained by pyrolyzing and ball-milling. The microstructure and component of the composite was characterized by SEM and XRD, the electrochemical performance was investigated by electrochemical impedance spectroscopy (EIS), cyclic voltammetry (CV) and galvano static charge-discharge tests. The results illustrate that the particle of Si/C composite prepared by pyrolysis exhibits inerratic morphology, uniform carbon-coating layer, good electrical conductivity, low resistance. The first intercalated-lithium capacity of the composite material is 4495 mAh/g; the first coulomb efficiency is 65.3%. From the second week the coulomb efficiency maintains 97%, and the capacity at the 100th cycle can …

Synthesis And Catalytic Property Of Flaked Spindle-Like Cuo Nanocrystals, Jian-Feng Fan, Li-Qing Li, Yu-Feng Huang, Lou-Zhen Fan

Journal of Electrochemistry

A simple and efficient electrochemical route was developed for the synthesis of flaked spindle-like CuO nanocrystals using aqueous electrolyte and Cu sacrificial anode (graphite as the cathode) in an undivided cell at a constant potential mode under room temperature. The morphologies, structure and component of CuO nanocrystals obtained were characterized by SEM, XRD, respectively. Flaked spindle-like CuO nanocrystals were successfully used to modify a GC electrode to detect H₂O₂ with cyclic voltammetry (CV) and amperometric (AC).The results showed that products were pure monoclinic CuO nanocrystals. The linear range for the determination of hydrogen peroxide is from 1.0 …

Investigation Of Supercapacitors Based On Polyvinyl Alcohol Hydrogel-Polymer Electrolyte, Kai-Qing Xu, Le-Qing Fan, Ji-Huai Wu, Qing Leng, Xin Zhong, Jian-Ming Lin, Miao-Liang Huang, Zhang Lan

Journal of Electrochemistry

For the first time, the supercapacitor based on the hydrogel-polymer electrolyte which consisted of the cross-linking of polyvinyl alcohol-glutaraldehyde (PVA-GA) using 2-acrylamido-2-methyl propane sulfonic acid (AMPS) as solicitation reagent was assembled. The gel polymer electrolyte was characterized by FTIR and AC impedance. The maximum ionic conductivity is 1.23 mS/cm at room temperature. The electrochemical properties of the supercapacitor were investigated by cyclic voltammetry, AC impedance spectra and constant current charge-discharge curve. The results show that the specific capacitance reachs 139 F/g with AMPS of 1.0 g and 0.05 mL of 5 %(by mass) GA. And the specific capacitance still retained …

Influence Of Tert-Butylpyridine On The Band Energetics Of Nanostructured Tio2 Electrodes And The Photoelectrochemical Properties Of Dye-Seneitized Electrodes, Shu-Ming Yang, Ji-Chao Wang, Hui-Zhi Kou, Hong-Bin Xue, Hong-Jun Wang, Yu-Ling Guo

Journal of Electrochemistry

The flat band edges (Efb) of nanostructured TiO₂ electrodes in electrolyte solutions with tert-butylpyridine (TBP) of different concentrations have been determined with spectroelectrochemical technique. TBP played a role in band energetics of nanostructured TiO₂ electrodes. The Efb values of -2.25, -2.46 and -2.62 V were determined in three 0.2 mol•L^-1 tetrabutylammonium perchlorate (TBAP) acetonitrile electrolytes which contain 0, 0.2 and 0.4 mol•L^-1 TBP respectively. The addition of Li+ ions shifted Efb positively. The Efb values of -1.12, -1.22 and -1.30 V were determined in three 0.2 mol•L^-1 LiClO₄ acetonitrile electrolytes which contain 0, 0.2 …

Electric Vehicles And Power Batteries, Xin-Ping Ai, Han-Xi Yang

Journal of Electrochemistry

In retrospect of the historical development of Electric Vehicles (EV), the impact of battery technologies on the progress of EV was discussed. In consequence, it is concluded that the lack of advanced batteries was the main cause for the fluctuations of EV development and the sluggish commercialization of electric cars in the past century. After a brief introduction to the classification and the requirements of electric vehicles, the main issues of the batteries including safety, temperature range for operation and the cost as well as the effects of these factors on the applications of advanced batteries for electric vehicles were …

Preparation And Electrocatalytic Activity Of The Pt/Wc/Tio2 Composites, Chun-An Ma, Bin Yu, Mei-Qin Shi, Xiao-Ling Lang

Journal of Electrochemistry

TiO₂ was used as the support for preparation of Pt/WC/TiO₂ composite catalyst. The composites were characterized by XRD, SEM and TEM methods. The electrocatalytical activity of Pt/WC/TiO₂ composite for oxidation of methanol was investigated by cyclic voltammetry. Pt/WC/TiO₂ exhibited higher activity compared with that of Pt/TiO₂ and Pt/WC composite catalysts. Based on this we discussed the effects of crystal phases of TiO₂ on the electrocatalytical activity of Pt/WC/TiO₂ composite catalyst.